Search Documents

By L. M. Chan, D. H. Carlson, J. B. Johnson

"Abstract — Concentrations of tailpipe pollutants from diesel-powered. underground mine vehicles change over time due to engine wear and the need for maintenance. Since this deterioration in pollutant emissions may adversely affect the air quality in an underground mine, it should be monitored and controlled. This paper presents decision criteria concerning when to service a mine vehicle diesel engine. These criteria, based on mine air and tailpipe concentration measurements, are designed to maintain the tailpipe concentrations within limits that assure satisfactory mine air quality.Application of the deterioration criteria to mine vehicle emissions involves:establishing, for each pollutant, the allowable deterioration factor, anddetermining the deterioration factor, from the mine air and tailpipe diesel pollutant measurements, and the mine air threshold limit values (TLVs).If the deterioration factor is greater than or equal to the allowable deterioration factor the vehicle is removed from service for maintenance.An analysis applying the criteria to measurements made in an underground coal mine is presented. The tailpipe pollutant concentration data were collected using the Emissions Mea-surement Apparatus (EMA) developed by Michigan Techno-logical University. Since the TLV for diesel particulate matter (DPM) has not yet been established assumed mine air DPMTLVs of 15 and 1.0 mg/m3 were used in the analysis. For all of the diesel haulage vehicles included in the analysis. DPM was found to be the critical pollutant (the one most in need of control). For an assumed mine air DPM TLV of 15 mg/m3 none of the diesel haulage vehicles would he removed from service. However reducing the DPM TLV to 1.0 mg/m3 would make it necessary to remove two of the three vehicles tested from service."

Mar 1, 1992

By L. G. Marshall

The geology, mining, beneficiating, types of products, and costs in terms of percent of total costs and of labor, power, and supplies of two crushed- limestone operations in Madison County, Iowa, are described in this paper. The operations are basically similar, differing in refinements in mining, product types, and markets. The operations are comparable as to personnel and as to weighted costs in terms of percent of total costs and in terms of man-hours, power, and supplies. The waste-to-stone stripping ratio is 1 to 0.8 at both operations, the powder factor is 0.29 pound of explosives per ton of stone, and daily production is 95 tons per man-shift. Both companies use crawler-mounted diesel shovels for loading, truck transportation, wagon drills, and dry screening.

Jan 1, 1963

By C. C. Knox

In Kiowa County, Okla., extensive deposits of clay are closely associated with pre-Cambrian anorthosites and gabbros. Investigation by the Bureau of Mines, including 1,723 feet of auger drilling, has shown the presence of very large quantities of clay containing between 20 and 25 percent alumina. All of the material contains large amounts of impurities, and even the best clays, selected for their relatively low content of iron, titanium, and magnesium, are unsuitable for the production of alumina by the sulfuric-acid process The soda-lime process gave somewhat better results, the product being nearer specification for commercial alumina. The clays are not amenable to beneficiation by simple sedimentation processes, and the alumina content could not easily be increased to produce material suitable for any alumina process.

Jan 1, 1948

By M. M. Wong

Salt mixtures consisting of KC1, BaC12, and HfCl4 with RbCl or CsCl were investigated as electrolytes for refining hafnium. The presence of RbCI or CsCl in the electrolyte appeared to suppress the volatility of. Best electrorefining was obtained with an electrolyte containing 50.7 percent KCl, 27.l percent BaCl2, 15.7 percent CsCl, and 6.5 percent HfCl4. In this electrolyte, hafnium metal with an average oxygen content of 470 ppm was produced from an anode feed containing l,600 ppm oxygen. All metallic impurities were lowered, except titanium, manganese, and tin.

Jan 1, 1966

By Oliver Bowles

Since 1922 when the Bureau of Mines issued a report2 covering the slate industry in detail, changes in technology have taken place which have an important bearing on the industry. The present paper comprises a record of these changes. Though the value of slate, for roofing, structural, blackboard, sanitary, and electrical uses is generally recognized, it has many competitors. To meet this constantly increasing competition producers are promoting economies in manufacture, and improving processes, thereby lessening costs of production, and are placing on the market products of the highest possible quality, thus creating satisfaction and confidence on the part of the user. This endeavor to place the industry on a better basis, both as regards processes and products, is shown in the recent developments in technology which are presented herein. Valuable assistance in obtaining data for this paper was given by W. S. Hays, secretary of the National Slate Association, N. M. Male, president of the National Slate Association, and Robert Notvest, consulting engineer, Cleveland, O.

Jan 1, 1926

By K. C. Dean

Changes in the types of materials used for the construction of recent automobile models have occasioned a review of the continued applicability of current recycling techniques. Plastics are being used increasingly in late model cars. To evaluate the changes occurring, a 1972 Mercury Montego, furnished by the Ford Motor Co., was completely dismantled and analyzed, and the composition was compared with that of a composite automobile from 15 vehicles ranging in date of manufacture from 1954 to 1965 and designated as a circa 1960 model. The composite vehicle contained about 26 pounds of plastics, while the 1972 model contained over four times that quantity. The increasing use of plastics in automobiles suggests that research to improve the economic potentiality of plastics recycling is warranted.

Jan 1, 1974

By Walter W. Fowkes

Leonardite is a coallike substance, similar in structure and composition to lignitic coal and believed to be derived from lignitic coal by the process of natural oxidation. Leonardite is little known outside lignite-producing areas and has been developed commercially only to a minor extent. The higher oxygen content and less compact structure of leonardite, compared with lignite, make it undesirable as a fuel but indicate that it has potential as a source of chemicals and for other nonfuel uses. It is a convenient source of humic acids. The United States has a large natural reserve of leonardite; furthermore, it can be produced in the laboratory under controlled conditions. The significant elemental difference between leonardite and lignite is the oxygen content (leonardite, 28-29 percent; lignite, 19-20 percent). The higher oxygen content of leonardite is due entirely to a Larger number of carboxylic acid groups. This fact explains the 17-Cold increase in alkali solubility of leonardite. Spectral studies indicate that the material is mixed salts of humic acids.

Jan 1, 1960

By Edward F. Divers

This Bureau of Mines report describes a new type of scrubber (dust collector) and ventilation system built into the auger support frame (boom) of a Jeffrey 120L continuous mining machine. With this twin scrubber arrangement, one scrubber is mounted into each side of the boom. Each scrubber includes a 2,500-cfm fan, a flooded fibrous-bed scrubber panel, and a water droplet eliminator. The system was designed for minimum size and adds only a few inches to machine height. Exhaust duct design allows flexibility with various airflow configurations to suit both blowing and exhaust fare ventilation systems and brattice distances ranging up to 20 feet. Full-scale tests with exhaust ventilation were conducted at a Mine Safety and Health Administration surface facility at Bruceton, Pa., to determine the scrubbers' methane dilution capability. Several configurations of the twin scrubber-ventilation system produced striking improvements in face methane dilution when compared with conventional systems.

Jan 1, 1981

By A. Adams

The Bureau of Mines determined the composition of the vapors liberated during thermal decomposition of aluminium nitrate nonahydrate. Small samples were heated from room temperature to 5500 C with initial heating rates from 500 to 2000 C/min. Gases were rapidly swept away from the heated chamber with Ar and subjected to immediate analysis in order to minimize reaction between the components. In addition to H20, four N-containing compounds were identified: HN03, N02, NO, and N20. Nz could not be determined in the presence of the nitrogen oxides, and at-tempted separation from the oxides led to the formation of more nitrogen. Relative amounts of each component were found to vary over a period of time; however, total amounts measured with different heating rates were reasonably constant and were typically as follows: 84.2 pct HN03, 7.1 pct N02, 4.3 pct NO, and 4.2 pct N20. HN03 and NO were determined from chemical reactions with a permanganate solution, N20 was measured with a mass spectrometer, and NO2 was measured with a spectro-photometer. Details of the methods used are described. Since NO2 and NO can readily be converted to HN03, about 96 pct of the N from the decomposition can be recovered as HN03

Jan 1, 1987

By G. W. Jones, F. E. Scott, R. E. Kennedy

Methylene chloride , dichloromethane CH2C12 , a low - boiling and highly volatile organic chlorinated compound, is used extensively as a refrigerant in air conditioning installations , as an intermediate in organic synthesis , and as a solvent for cellulose acetate and other materials . As its vapors are not inflammable in air at ordinary temperatures , it can be used to advantage where it would be highly dangerous to use ordinarily inflammable solvents . The question has been raised as to its inflammable range in pure oxygen and in air enriched with oxygen . To find the answer to this question, tests were carried out with various mixtures of methylene chloride , oxygen, and nitrogen mixtures . It was found that methylene chloride has wide limits of inflammability in pure oxygen . Additional tests were then made to establish the complete range of inflammability of these gases . The methylene chloride employed in the tests was cbtained from the Eastman Kodak Co. It had a reported boiling range of 40.5 ° to 42.0 ° C. and a density of 1.322 at 20 ° C.

Oct 1, 1943

By G. L. Oldright

[This paper is the fifth 4/ of a series of publications on smelting in the load blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation, and to correlate the behavior of the furnace at various tines with the main factors governing the operation of the blast furnace, and metallurgical losses.]

Jan 1, 1929

By Maria I. DeRosa

This Bureau of Mines report describes the Automated Breathing Metabolic Simulator and its hardware and software systems with emphasis on the role exerted by the software program subroutines in controlling the hardware mechanisms during the simulation of man's respiratory and metabolic functions.

Jan 1, 1978

By R. Hogg, T. F. Dumm

"Procedures for particle size analysis on respirable dust from coal mines have been evaluated. Using respirable dusts dispersed in a laboratory dust chamber, size distributions measured using cascade impactors have been compared with the results of a variety of laboratory sizing methods performed on samples collected on filters placed side-by-side with the impactors. The laboratory techniques included centrifugal sedimentation, laser diffraction/scattering and automatic particle counting. The general agreement among the various methods was very good, with systematic differences which can be attributed to the different definitions of size used. Simple conversion factors have been obtained which can be used to transform the laboratory data to equivalent aerodynamic sizes.Similar comparisons have been made on samples collected in underground coal mines. Again, the results are in quite good agreement although small discrepancies were observed in· some cases. These have been attributed to some degree of agglomeration in the airborne dust, leading to slightly coarser apparent distributions in the impactor samples INTRODUCTIONA primary goal of mine ventilation is the control of airborne dust, especially in the ""respirable"" size range, typically defined as finer than about 5 to 10 µm. It follows that determination of the amount and characteristics of the respirable dust is an important factor in evaluating the performance of ventilation systems. Particle size information on airborne dust in mines is commonly obtained by in- situ measurements using cascade impactors. However, these tend to be inconvenient for routine data collection and the alternative approach of collecting samples in the mine, on filters for example, and returning them to the laboratory for detailed analysis is very attractive. Questions have often been raised, on the other hand, as to the appropriateness of this approach. How well · do such laboratory methods describe the distribution of aerodynamic diameter of the airborne dust particles in the mine environment? The purpose of the work described in this paper was to evaluate some laboratory sizing methods and to compare the results of such measurements with the size data obtained by the direct, in-situ method."

Jan 1, 1989

By E. D. Gradner

During 1924 a number of lives were lost and other men incapacitated by the toxic effects of gases produced in blasting in massive sulphides. In one mine, three men working in a raise were caught by gases from blasting a drift round in massive sulphide on the level. The round in the drift was shot ahead of time and it was necessary for the three men to travel through the gases to the intake air course. Two of the men lost their lives, and the third was injured, apparently for life. Other men at this same mine have been caught in the gases at blasting time and seriously injured. At a second mine, the gases from blasting in sulphides appear to be very dangerous, and it was necessary to send a number of men who were caught in such gases to the hospital. One man who was seriously gassed has not recovered in over a year is time. Another man similarly gassed soon died of influenza.

Jan 1, 1926

By James V. Luxner

The airflow and methane distribution patterns developed in an equipment-free entry 6.5 feet high and 12 feet wide, ventilated by line brattice operated blowing to or exhausting from the face, were determined by the Bureau of Mines for varying conditions. Results of these studies show that blowing line brattice systems of face ventilation are more effective than comparable exhaust systems. The face ventilating efficiency of any line brattice system is dependent upon the method of ventilation, the face distance, the tight rib distance, the volume of air delivered to the end of the line brattice, and the volume of methane released at the face. Experimental results indicate that maximum face ventilation efficiency is achieved when the inby terminus of the line brattice is installed 5 feet from the face and at a distance less than one-third the entry width from the nearest rib. Analyses of data are based upon the ability of a face ventilation system to dilute methane in the immediate face area.

Jan 1, 1969

By David E. Emerson

An improved method and apparatus for determining the impurities in helium by preconcentration and subsequent analysis by mass spectrometry are described. Preconcentration of the impurities is accomplished by passing a known volume of helium, at slightly above atmospheric pressure, through a metal coil and trap assembly immersed in liquid helium. The concentrated impurities are then analyzed by mass spectrometry. This method can detect impurities in the range of 0.01 to 600 ppm with an accuracy of better than ±0.05 ppm at the 1-ppm level. One operator can analyze 15 samples in an 8-hour day.

Jan 1, 1970

By W. G. Messner

Pipelines for transporting crude oil and refined products in the United States totaled 189,982 miles on January 1, 1959. This mileage was less than a 1-percent increase from the 1956 total of 188,540 miles. During the three-year period (January 1956 - January 199), 14,886 miles of new pipe and 10,649 miles of secondhand pipe was laid. Pipe taken up in the same period was 24,093 miles. The facts regarding pipeline mileage were obtained by the Bureau of Mines from pipeline companies and information provided by the Interstate Commerce Commission. Crude-oil gathering lines, as of January 1959, were 40 percent of the United States pipeline mileage and totaled 75,182 miles, an increase of 1,656 miles during the three-year period. Crude-oil trunklines totaled 70,317 miles or 37 percent of the United States pipeline mileage, a decline of 8,277 miles from the 1956 total. Some of this loss is attributed to the converting of crude lines to refined products. Refined product lines in January 1959, totaled 44,483 or 23 percent of the United States mileage, an increase of 8,063 miles during the three-year period.

Jan 1, 1959

By George T. Motock

The author prepared the following report as the result of a trip to Germany in the summer of 1945 for the Technical Industrial Intelligence Commitee Subcommittee on Metals and Minerals. The purpose of this committee, which functions under the Joint Intelligence Committee of the Joint Chiefs of Staff of the United States Armed Forces and of which the Bureau of Mines

Jan 1, 1946

An evaluation of blasting procedures in surface mining operations was undertaken to determine means for improving safety. The objectives of the study were to: 1. Develop guidelines for safer blasting practices 2. Specify changes or additions in regulations concerning the use of explosives 3. Identify areas in which additional knowledge needs to be developed. As a basis for the evaluation, an idealized blasting cycle was prepared. Developed in the form of a scenario of surface mining operations, this synthesis of good mining practices served as the standard against which observed activities were compared. Blasting hazards were divided into two categories: those known to exist and those which are potential. Known hazards were identified in terms of situations which have actually resulted in explosives-related accidents. The evidence for known hazards was obtained primarily from MESA records of mine accidents. Potential hazards were identified by observation of mining activities and consultations with mining, explosive industry and government regulatory agency personnel.

Jan 1, 1977

By Graham W. Marks

The general positions of the absorption maxima of aqueous solutions of the violet and green isomers of chromic sulfate the visible spectral region have long been known, but, to the knowledge of the writer, no comprehensive studies have ever been made. To gain further knowledge concerning these inorganic complexes and to investigate the possibilities of developing an analytical method for determining the concentrations of the violet and green isomers in a mixture, a more complete investigation was made in the spectral range from 325 to 850 millimicrons.

Jan 1, 1951