Search Documents

By Andrew B. Cecala

While various types of equipment are used in bulk material processing plants to control respirable dust, the equipment often doesn't adequately protect workers. One cost-effective way to supplement your existing dust control equipment is to install a whole-plant ventilation system. This article outlines research by the National Institute of Occupational Safety and Health (NIOSH) on using whole-plant ventilation in two mineral processing operations to reduce respirable dust levels. Information also covers how to design a ventilation system for any bulk material processing plant.

By J. A. Ruppert, P. M. Sullivan

A study was made of filtration techniques for recovering the major part of the tin contained in iron - tin alloys known as hardhead . Special smallscale filtering apparatus and a three - stage cyclic process were developed . Eighty- seven percent of the tin contained in an alloy of 82 percent tin and 17 percent iron was recovered as pure metal by pressing at 975° C followed by a second pressing at 800 ° C and a final filtering at 250 ° C. Small amounts of Sb , Cu , and Fe impurities were removed by adding Al to the molten product and performing another filtration at 250 ° C.

Jan 1, 1964

By Franklin H. Persse

To meet escalating energy requirements, substantial increases in production from the strippable coal and lignite deposits in eastern Montana, western North Dakota, and northeastern Wyoming already have occurred, and further expansions are expected at least until the year 2000. Such production, attributable largely to rising demand for low-sulfur coal, must be accomplished with a minimum of adverse effects on the environment. Information on geology, climate, and current land use in the Upper Missouri River basin is presented in the Bureau of Mines review as a guideline to what operators may expect during and after mining. Proven methods of protecting the air and water from pollution and of restoring mined land for other uses are described, and untried methods of land reclamation, some with equipment yet to be manufactured, are discussed as possible means of maintaining aesthetic values in the basin. Costs incurred to protect the environment are part of the production cost and thus are borne by the ultimate consumer. Unit production costs are less for the thick coal and lignite deposits of the basin than for the thinner but higher Btu coal deposits of the Eastern and Midwestern United States. Precise comparisons of environmental protection costs between mines in such disparate areas cannot be made, because of differences in physical conditions, accounting procedures, and other variables.

Jan 1, 1975

By S. H. Ash

NO MORE important question has come before the coal-mining industry in many places, especially in the anthracite region of Pennsylvania, than prevention of stream pollution by mine drainage. Available information on acid mine drainage in the anthracite region of Pennsylvania indicates that a pollution problem must be solved in any program of anthracite mine drainage. The major problem concerns satisfactory disposal of the daily average mine-water discharge of 327,000 gallons per minute (g. p. m.), or 472 million gallons per day (g. p. d.), containing a free-acid load of 431 tons or a total acid load of 934 tons a clay as H2S04. This report indicates the scope of the problem and gives some suggestions concerning its solution.

Jan 1, 1951

By Stephen R. Wilson

The West Tintic mining district is located at the southern end of the Sheeprock Range in Juab County, Utah (fig. 1). Scheelite was discovered in the area during 1940, and the Desert Tungsten Co. began mining in May 1942. The ore was shipped to the Metals Reserve Co. chemical treatment plant at Salt Lake City during the war. A Bureau of Mines development project was established on property controlled by the Desert Tungsten Co. Work was started during September 1942 and completed in February 1943. The program included removal of overburden in the mine area to facilitate geologic napping, followed by surface trenching, diamond drilling, and sampling (figs. 2,. 3, 4, and 5). Eleven diamond-drill holes totaling 1,480 feet were drilled from the surface. Sixty-one samples from the surface trenches and diamond drill holes were assayed. The logs of the holes are given in table 2. Assay results of samples from the surface trenches and diamond drill holes are listed in tables 1 and 3. Geologists of the U.S. Geological Survey mapped the mineralized area during the project period. The scheelite deposits occur in limestone areas adjacent to intrusive m9.sses, which are principally monzonite. The ore bodies are pyrometasomatic in origin, but consist of two somewhat different types: (1) a series of veins occupying fault zones in limestone and (2) tactite bodies immediately adjacent to the limestone. The veins in the limestone have been the most productive of the two types.

Jan 1, 1950

By R. A. Beall

Consumable-electrode arc melting is now accepted throughout the industry as the best method for producing ingots of zirconium, titanium, molybdenum, and their alloys. In addition, the technique is widely used in laboratories for fusing samples of such metals as hafnium, chromium, tantalum, columbium, and thorium. The production of consumable electrodes from these metals presents some rather difficult problems, the accepted industrial solution being the use of heavy powder-metallurgy-type presses. This paper summarizes information on fabrication of consumable electrodes by this and alternative means, such as sintering, nippling, and welding lightly pressed compacts of scrap metal. A possible saving of considerable capital investment is shown in the case of sintered compacts. The electrical circuit components of a pilot sintering unit are analyzed. INTRODUCTION The consumable-electrode arc-melting process has been accepted by most of the industry as the best method at present for producing high-quality pure or alloy in-got from sponge titanium or zirconium. This technique is not particularly new, having been patented by Von Bolton (l)3/ in 1909 for melting tantalum. However, it has been applied to industrial-scale operation only in the last few years. Among the important contributions to this technique are the work of Kroll (2) and Parke and Ham (3) and the work reported by the Office of Naval Research (4). The Bureau of Mines-has added considerably to the knowledge of this process (5-9).

Jan 1, 1956

By G. T. Brow

An experimental method is described for testing diffusion of gases in crude oils at pressures and temperatures up to 3,000 psia and 200° F. A sampling technique was developed to withdraw by constant-pressure mercury displacement about 60 µl of oil from the diffusion cell through any of several 1/2-in vertically spaced capillary tubes and to trap about 4 µl of the oil in a specially designed microsampler. Oil trapped in the microsampler can be completely inserted in the sample inlet of a chromatograph. From analysis in a three-stage chromatograph (GLC), gas concentration in a sample is determined from the ratio of gas peak heights to area of peaks of reference components (hexanes or heptanes) in the oil. A diffusion coefficient is calculated from measured concentration profiles with known equations for diffusion in finite or semi-infinite systems, depending on whether the gas has or has not reached the end of the oil column. Results are given for a test of methane diffusing at 2,560 psia and 160° F in crude oil from the Weber Sandstone reservoir in the Rangely field, Colorado. A constant diffusion coefficient of 3.34 X 10-5 cm2 per sec was obtained which gives a good fit between calculated and experimental profiles determined at six times after start of diffusion. The maximum standard error of gas concentration determinations experienced with this method was ±0.88 ml per ml of gas-free oil.

Jan 1, 1970

By J. E. Tiffany, Z. C. Gaugler

An active list of permissible explosives was published in December 1943 as part of the Bureau of Mines Report of Investigations 3736 under the title "Active List of Permissible Explosives and Blasting Devices Approved Previous to June 30, 1943." This list included 180 brand names. Changes in the list that have been authorized to December 31, 1945, placed 10 additional brands of permissible explosives on the active permis- sible list as a result of tests and changes in brand names.. Twelve permis- sible explosives were transferred from the active. to the inactive list. The present list contains 178 brand names. The brand names of the permissible explosives placed on the active list are as follows: American 3-A By test. Apcol No. 1-B Do. Black Diamond No. 11-B DO. Black Diamond No. 55 DO. Coalite G-1 DO. Coelite K-1 Do. Do. Coalite L-1 Coalite IS-1 Columbia B-2 DO. By change in name. By test. Monobel AA The permissible explosives transferred from the active to the inactive list are as follows: Anthracite B, L. F. Big Red No. 8 Independent No. 1, L. F. Independent No. 2, L. F. Independent No. 3, L. F. Independent No. 4, L. F. Independent No. 5, L. F. Independent No. 9, L. F. Independent No. 9-C, L. F. Independent No. 10, L. F. Independent No. 11, L. F. King No. 9

Jul 1, 1946

By A. F. Jolly

As a part of ongoing research into the sulfidation partitioning of selected complex minerals, the U.S. Bureau of Mines conducted research designed to selectively recover Cu from sulfidized chalcopyrite (CuFeS2). Ferric chloride (FeCI3) solutions leached >90 pct of the Cu and <20 pct (sometimes < 10 pct) of the Fe in the sulfidized concentrates. Cupric chloride (CuCI2) leaches were even more selective, solubilizing essentially 100 pct of the Cu and < 5 pct of the Fe. In contrast, leaching non-sulfidized CuFeS2 with either FeCl3 or CuCl2 showed that somewhat more Fe than Cu dissolved. These studies demonstrate that Cu is substantially more leachable from sulfidized CuFeS2 than from nonsulfidized CuFeS2? The Cu-and Fe-bearing constituents generated as sulfidation products, CuS (covellite) and FeS2 (pyrite), respectively, are differentially dissolved. The solubility of Fe from pyrite in sulfidized CuFeS2 is much lower than the solubility of Fe from complex nonsulfidized sulfide where Fe and Cu are bound in the same crystal lattice. Thus, the Cu dissolves selectively, producing a high-Cu filtrate from which Cu can be recovered by cementation or by electrolysis. Flotation of CuS-FeS2 mixtures indicates partitioned phases can be physically separated if effective liberation can be achieved. Magnetic separation tests yielded less promising results.

Jan 1, 1991

These proceedings consist of papers presented at two Bureau of Mines Technology Transfer Seminars in early 1980 for the purpose of disseminating recent advances in mining technology related to surface coal mining reclamation.

Jan 1, 1980

By G. W. Birge, D. E. Wolfson, J. G. Walters

An investigation was conducted to determine the relationship between ASTM and Micum tumbler data and to develop equations that would enable the conversion of data from one test method for comparison with those determined by the other , and thereby facilitate the international exchange of data . Relative strengths of 18 commercially produced cokes were determined by ASTM and Micum tumblers and ASTM shatter test . Two of the samples were coke produced for foundry use , and two were produced in beehive ovens . The remaining 14 samples were produced for blast furnace consumption and had ASTM tumbler stabilities of 36 to 58. Statistical procedures were used to relate the three test methods and also to evaluate the effect of charge weights , top sizes of coke , and types of screens specified by the two standard tumbler procedures , square - hole wire mesh for the ASTM tumbler and punched round - hole for the Micum . A significant result was that the data obtained with like screens have a higher degree of correlation with a smaller standard deviation than data from the screens specified for each tumbler .

Jan 1, 1964

Studies on coal mine drainage sludge densification have led to the following conclusions: 1. Coal mine waters containing iron principally in the ferrous (Fea+) state can be treated by a modification of the commonly practiced lime neutralization process to yield a ferromagnetic sludge. The sludge, presumably composed in large part of a hydrated ferrosoferric oxide (Fe304.xH20), is much denser and faster settling than the ordinary "yellowboy" sludge obtained by lime neutralization and aeration at ambient temperatures. 2. The magnetic sludge preparation technique involves (quantitative) precipitation of iron (largely as Fe(OH)2) by the addition of hydrated lime to a pH of 8.5, separation of the resulting sludge from the aqueous phase, and heating of the sludge concentrate to at least 80 C (176 F), preferably higher, followed by mild aeration. 3. Magnesium, present as Mg2 in most coal mine drainage waters, inhibits the formation of the magnetic sludge. This inhibition can be adequately minimized by keeping the pH below 9.6 during lime addition (thus avoiding the coprecipitation of Mg(OH)2) and by separating the sludge from the bulk of the aqueous phase before the heating step, as indicated in (2) above. 4. Aluminum, commonly present in coal mine drainage waters, also inhibits the formation of the magnetic sludge. This inhibition is of practical significance when the molar ratio of aluminum/total iron is greater than 0.18. Below this value, sludges are still appreciably magnetic, but are bulkier and slower settling than those obtained when aluminum is absent. Unlike magnesium inhibition, aluminum inhibition cannot be minimized by the scheme indicated above, since aluminum precipitates as Al(OH)3 near pH 4 and remains dispersed within the sludge. 5. The limitation on aluminum content is probably the most serious restriction affecting the feasibility of the magnetic sludge process as presently conceived. Nevertheless, a limited review of available water quality data has indicated that, in terms of relative acid and iron loadings, a significant number of major coal mine discharges in the eastern Ohio River basin may be amenable to treatment by a magnetic sludge process. 6. Data from tests on the use of magnetic seeding materials indicate that seeding did not enhance the formation of a magnetic sludge under the experimental conditions employed.

Jan 1, 1971

By J. B. Zadra, J. M. Gomes, Don H. Baker

Electrolytic deposition at 1,000 ° C in an electrolyte essentially consisting of 7 parts sodium pyrophosphate , 2 parts sodium chloride , and 1 part sodium tetraborate yielded tungsten of 99.9 percent purity . Scheelite concentrates containing 25 to 73 percent WO, and varying quantities of iron , lime , and silica were used as feed materials for the electrolysis . The metal contained less than 0.01 weight - percent each of iron , calcium , silicon , aluminum , carbon , and oxygen . Modification of the electrolyte permitted deposition of equal - quality metal from scheelite concentrates containing higher quantities of iron , calcium , and silica . The electrolytic separation of molybdenum and tungsten was accomplished by minor variations in the operating procedures .

Jan 1, 1964

By S. Don Brown

Between 1987 and 1988, the Bureau of Mines studied the mineral resources of the White River National Forest and part of the Arapaho National Forest to appraise the resources present and to determine the types of deposits, and their location, that could be mined economically if sufficient demand and metal prices existed. The study included a comprehensive literature search and a limited amount of field investigation of minerals and mining activity in and near the Forest. Mineral resource information indicates that in the Gore Range the area between Tennessee Pass and Gilman may contain large base-and precious-metal deposits, and could be the focus of exploration activity in the near future. The Breckenridge mining district was found to have a moderate to high likelihood for mineral exploration and possible development of gold. Recent exploration and minor development work has occurred in several other areas: Montezuma, Kokomo-Tenmile, and Upper Blue River districts, and portions of the Sawatch Range. Limestone, marble, sand and gravel, rock for crushed aggregate, and other industrial rocks have been recently mined or Quarried in the Forrest, and will likely be mined or quarried in the near future. Currently coal is being produced at one mine in the Forest, and extensive identified coal resources are located in the Forest. Parts of four known gas fields lie within the Forest west of Glenwood Springs; there is current production at one field.

Jan 1, 1990

By A. Renton Amell

The rate of dissolution of U02 was measured in acid solutions similar to those used for in situ leaching, with S04 of 10-1.82 to 10-4 M, Fe(III) of 10-2 to 10-4 M and pH&apos;s of 1.1 to 2.3. The dependence of dissolution rate on pH was small and inconsistent, probably reflecting the combined effects of a very weakly polar oxidizing complex, probably FeSO4+, and a nearly neutral U02 surface. Differences in the state of the U02 surface may explain this variability as well as contrasts between these results and results reported in other work. Changing either S04 or Fe(III) concentrations significantly affects dissolution rates. Increasing low sulfate concentrations in solutions containing 10 2 M Fe(III) at pH 2 results in formation of FeSO4+. In such solutions, rates increased with (S04)/(Fe(III)) up to 1:30, thereby indicating that the oxidation of U02 by FeSO4 is more rapid than by Fe3+. However, the dissolution rate decreased at higher (SO4)/ (Fe(III)), due either to sorption of SO42- on the UO2 surface or to formation of other less reactive sulfate complexes such as Fe(S04)2 or FeHSO4+ However, Fe(III) concentration is the dominant factor in determining solution rates. The rate was directly proportional to ferric iron concentration, indicating that the rate-determining step of the dissolution reaction is a single-electron oxidation by a ferric complex. Dissolution rates were lower in solutions of 0.1 and 1.0% H202 (0.029 and 0.29 M) than at similar concentrations of ferric iron because of formation of an insoluble surface coating of uranium peroxide, UO4?4H20. This phase may limit the value of hydrogen peroxide as an oxidant in lixiviants, not only by its very low solubility, but perhaps also by filling pores and reducing permeability in the ore body.

Jan 1, 1978

By M. E. Tyrrell, C. W. Houck

Mixtures of zirconium diboride and refractory metals of group VI were resistance sintered to high - density compacts using modified electric welding equipment . To evaluate the use of chromium , molybdenum , or tungsten as binders for zirconium diboride the sintered compacts were examined in polished sections and tested for crushing strength , hardness , microhardness , oxidation rate , and resistance to mechanical shock . Chromium yielded the highest compressive strength , the greatest resistance to mechanical shock and oxidation , and a satisfactory Rockwell hardness . Molybdenum did not yield a satisfactory cermet . Tungsten yielded compacts having high microhardness but very low mechanical strength .

Jan 1, 1964

By Ivan L. Nichols

Tailings dumps at Mercur, Utah, contain about $7 million worth of gold in 3.5 million tons of mill tailings assaying about 0.07 ounce of gold per ton. Commercial mining and milling at Mercur ceased in 1942. To determine whether improved technology was now available that might permit economic reprocessing of the Mercur dumps, the Bureau of Mines probed for a low-cost method that would be applicable to these tailings. A composite sample prepared for laboratory studies assayed 0.062 ounce gold per ton. About 10 percent of the gold occurred as a water-soluble cyanide. Conventional cyanide leaching dissolved 32 percent of the gold, and hot, strong cyanide solution dissolved 42 percent. Results were not improved by pretreatment with acids, bases, or oxidants. After expensive preroasting, gold recovery by cyanidation was increased to 65 percent. The simple procedures were ineffective, and more effective procedures were too costly for economical processing of Mercur tailings.

Jan 1, 1970

By A. R. T. Denues, A. P. Rowles

"INTRODUCTION Summarized data developed by J. E. Crawshaw and E.J. Murphy, 4/of the Explosives Division of the Bureau of Mines, suggesting marked variations in oxygen condition in three permissible explosives, have been reported 5/. Such variation is of interest in other work, it having been shown, for example, that the oxygen condition may have marked effect upon the products 3/ and the propulsive strength 7/ of explosives. It seemed that a more detailed presentation and more usual statistical analysis of these data might be of considerable general interest and not complemented in the literature.This report presents both the original data developed by Crawshaw and Murphy and the results of a simplified but seemingly acceptable statistical analysis of these data. The logical ground for this analysis might seem somewhat questionable because of the lack of systematic information concerning the extent of errors in the analytical procedure but the data show that there are several cogent and seemingly unequivocal indications of real heterogeneity in the explosives."

Jun 1, 1942

By Welby G. Courtney

The Bureau of Mines conducted a field test program in the Pittsburgh coal seam to investigate the effect of water sprays in the suppression of respirable dust being formed while cutting with a continuous-mining machine. Emphasis was given to the location of spray nozzles on the top and bottom of the cutting boom. Results showed that (1) sumping caused about 60 percent of the dust escaping the face area, and shearing and loading caused the other 40 percent; (2) during sumping, top and bottom sprays were equally effective in dust suppression and reduced dust ~13 percent; (3) during shearing and loading, bottom sprays reduced dust 61 percent and were about 50 percent more effective than top sprays; (4) the combination of top and bottom sprays was slightly more effective than the separate systems, but water consumption increased 60 percent; and (5) inclusion of throat sprays decreased dust reduction by removing some of the water from top and bottom sprays where it was more effective.

Jan 1, 1978

By Fermont F. Clarke, Others, Paul Zinner

"INTRODUCTION The Edison mine comprises workings on two irregular spodumene-bearing pegmatite dikes which outcrop near the town of Keystone in the southern portion of the Black Hills of South Dakota. The Bureau of Mines conducted an investigation of the Edison mine as part of a comprehensive study of the lithium mineral-production possibilities in the Black Hills area. The work was undertaken during the Second World War, when the demand for certain lithium salts and compounds exceeded the then small productive capacity of the industry.During the course of the project, the Bureau of Mines completed 13 diamond core-drill holes, aggregating 2,114.5 feet of drilling. Twenty-six cannel samples were taken from the main Edison shaft, and 13 miscellaneous samples were obtained to permit analysis of the efficiency of phases of mining and sorting operations. Metallurgical tests were made by the Bureau of Mines to investigate the feasibility of beneficiating spodumere-bearing ores from the Edison mine. 3/"

Apr 1, 1948