Search Documents

By T. T. Read, T. L. Joseph, F. H. Royster

In a preliminary study of the beneficiation of iron ores conducted by the Bureau of Mines, one of the authors (T. T. Read) found it necessary to ascertain, if possible, how much effect a decrease in the silica content of an iron ore has upon the cost of making pig iron from the ore. In the beneficiation of iron ores the most important impurity to be removed is usually silica, and the amount that can be expended on a beneficiation process to reduce the silica content of the ore is obviously determined by the amount of increase in the value of the ore after beneficiation. The price that can actually be obtained for a beneficiated ore is, of course, a matter of negotiation between the seller and the buyer, but since the relative value of different grades of iron ore must be chiefly based upon the cost of making pig iron from them, an approximation as to the effect which decrease in the silica content of ore has upon the cost of snaking pig iron is an important guide in estimating what probable average gain will result from subjecting an ore to a beneficiation process. A search of the literature failed to reveal any detailed statement on this important topic, but fortunately the data are at hand to permit making an approximate calculation of the probable effect. For the purpose of the calculation assume three iron ores with the following composition (natural):

Jan 1, 1924

By W. L. Acherman

Molybdenum, tungsten, and vanadium were found by the Bureau of Mines to possess generally superior chemical and galvanic corrosion properties in many aqueous corrosive media at temperatures up to the boiling point. The corrosion resistance of vanadium in certain solutions was further improved by alloying it with such metals as columbium, tantalum, and titanium. was susceptible to a type of crevice corrosion in mercuric chloride solutions, but no other instances of crevice corrosion were encountered. With few exceptions, molybdenum, tungsten, and vanadium were not adversely affected when coupled with dissimilar metals in galvanic corrosion experiments; in some cases one or both members of a couple were protected by contact. When exposed to aqueous ammonia spray at 60° C, all three metals were attacked, but they were moderately resistant in spray environments of substitute ocean water and ammonium dihydrogen phosphate.

Jan 1, 1966

The number of railroad coal cars (open top hoppers), dominated rail car orders and deliveries in 1975 according to announcements made February 11, by the Association of American Railroads and the American Railway Car Institute. Acting to keep ahead of increased coal production, the railroads installed 21,748 new coal cars in 1975, the most since 1957. The 1975 installation resulted in a net increase of 6,560 coal cars and an overall gain of 4.5 percent in the total capacity of the hopper car fleet. With most of the new coal cars going into unit train service --where car utilization is greatest --the railroads actual coal-carrying capacity was increased far more than 4.5 percent. The AAR estimated that unit train operations now move 50 percent of all rail-hauled coal compared to only 42 percent 2 years ago. COBALT - The Societe Miniere de Tenke Fungurume (SMTF) copper-cobalt project in Zaire reportedly was suspended in January for an indefenite length of time. According to officials, the deferment resulted from a number of adverse factors, one of which was exceptional increases in capital costs. The project was scheduled for completion in early 1978, with an eventual production of 14.3 million pounds of cobalt per year. Reserves of cobalt were reported to be 505 million pounds. SMTF is a consortium and includes American, British, French, Japanese, and Zairian interests.

Jan 1, 1976

By Frederick W. Lee

List of contributing editors of Geophysical Abstracts:

Sep 1, 1932

By Victor E. Kral

"SUMMARYFollowing a magnetometer survey on the McCoy iron deposit, a trenching and drilling program was carried out by the Bureau of Mines in August 1944.This deposit is 32.3 miles southwest of Battle Mountain in the McCoy Mining District, Lander County, Nevada, and lies on the east flank of the Fish Creek Mountains at an altitude of 5,400 feet, about 1 1/2 miles south of the gold camp of McCoy.Total production from the deposit has been 400 tons of magnetite, mined by hand and shipped to the west coast for ship's ballast.Bureau drilled two holes to a total depth of 92 feet and excavated 12 feet of trenches. Both holes were drilled in the same ore body and engineered magnetite ore 14 and 11 feet thick. Trenching was used successfully to show the lateral limits of the ore.Magnetite ore bodies were found to occur as replacements of a limestone bed in quartzite. They outcrop near and parallel to the exposure of a diorite entrusting that forms a long westward-trending ridge. Although magnetic outcrops can be traced for 5,000 feet trenching definitely proved the ore bodies to be disconnected to have little or no lateral extent beyond their outcrops. Only two ore bodies more than 10 feet thick were found; one of these is the inaccessible to and the other was drilled by the Bureau."

Jan 1, 1947

By John E. Pahlman

The Bureau of Mines conducted column-leaching tests on 25 domestic Mn ores to determine the feasibility of extracting Mn by in situ or heap leaching with dissolved sulfur dioxide (S02) solutions. The ores tested were obtained from deposits in Arizona, Arkansas, California, Colorado. Maine, Minnesota, Nevada, and South Dakota. Dissolved S02 was found to be effective for leaching Mn; extractions greater than 90 pct were obtained with solution application rates of 1 mL/min from uncalcined, minus 2.5-plus 1.3-cm ore pieces. Leaching these ores with solutions containing only 5-wt-pct S02 and no added H2S04 resulted in Mn being selectively extracted over Fe except when Fe was present as goethite or siderite. Ca solubilization was inhibited by controlling the solution application rate (1 mL/min). The rate of leaching was found to be principally dependent upon the rate at which the leaching solution can penetrate the ore, since the solubilization of Mn upon contact with S02 was observed to be rapid. Despite low water permeabilities of the ores (as low as 10-2 to 10-4 darcy). greater than 90 pct of the Mn was extracted from even the largest ore pieces tested (approximately 10 cm in diameter). It appears, therefore. that leaching Mn opens up the pores, allowing penetration of the leach solution into the ore pieces.

Jan 1, 1988

By Walter R. Storms

This paper, which describes the mining methods of the Potash Co. of America in Eddy County, N. Mex., is one of a series being prepared by the Mining Branch, of the Bureau of Mines on mining practices and methods in various mining districts of the United States. 4, T. The mine and plant of Potash Co. of America are situated in sec. 20 S., R.. 30, E.,. N. M. P. M., about 22 miles by paved road northeast of Carlsbad (fig. 1). A spur line of the Atchison, Topeka & Santa Fe Railroad also connects the mine with Carlsbad.

Apr 1, 1948

By Fei Chen, Lesley J. Gaydos, Laurence M. Demers, Douglas C. Kuhn

The fibrogenic effects of silica in experimental animals and humans has been extensively studied (I 7, 20). However, the pathogenesis and molecular mechanisms underlying lung injury and fibrosis resulting from silica exposure remain to be elucidated. It is well-documented that silica can stimulate monocyte-macrophage lineage cells to produce cytokines and growth factors, including interleukin-I (IL- I) (20), tumor necrosis factor-ex (TNF-cx) (I 7), insulin-like growth factor-I (IGF-1) (4), and transforming growth factor-P (TGF-P) (24). Consequently, it has been suggested that the fibrogenic effect of silica may be mediated by cytokines in the fater stages of silicosis. During the early phase of interaction between silica and the pulmonary alveolar macrophage, several direct and indirect lines of evidence suggest that reactive oxygen intermediates (ROI) may play a pivotal role in silica- induced tissue damage (2I, 22). One of the most important components of and contributors to ROI is nitric oxide (NO) produced from L-arginine and molecular oxygen under the catalytic influence of NO synthase (NOS) (I 9). At present, at least three NOS genes have been cloned: a constitutive neuron NOS, a constitutive endothelial cell NOS and an inducible NOS (iNOS) (16). A number of factors have been shown to differentially induce iNOS gene expression in different cell lines including bacterial cell products and foreign antigens. During inflammation, NO is a double-edged sword in terms of the host immune defense mechanisms and the physiologic response to an inflammatory insult. The macrophage is one of the major cellular sources of NO. During the early phase of acute inflammation, NO produced from the macrophage appears to facilitate the clearance of pathogens and promotes a local relaxation effect on the microcirculation of vascular smooth muscle. When the production of NO is left unattenuated, especially under oxidative stress, direct cytotoxic effects of NO can emerge through the formation of peroxynitrite as a result of a reaction between NO and superoxide (2).

Jan 1, 1998

These tentative inspection standards have been prepared as a guide for the Federal inspection of the anthracite mines of the United States. The Federal Coal Mine Inspection Division is not a mining-law-enforcement

Jan 1, 1943

By Mah Alla D.

Previously existing heat-of-formation values for the oxides of vanadium were rudimentary. They were subject to uncertainties of 1 to 5 kilocalories per gram-atom of contained oxygen. This fact has been the only adverse influence on the accuracy of thermodynamic calculations involving these substances, as the requisite entropy and high-temperature heat-content data are known with reasonable accuracy. This report presents new heat-of-formation data for four oxides of vanadium (VO, V203, V02, and V205), obtained by combustion calorimetry. It is believed that the uncertainties have been reduced to 0.1 to 0.3 kilocalorie per gram-atom of contained oxygen. The new heat-of-formation data were combined with existing entropy and high-temperature heat-content values to obtain free energies of formation of the four oxides at temperatures up to 2,000° K.

Jan 1, 1961

By T. L. Hebble

The Bureau of Mines investigated a hydrometallurgical procedure to recover Co, Ni, and Cu from an electrolytic zinc industrial copper filter cake. The copper filter cake is presently unmarketable or of low value because economic and environmentally acceptable processing technology is lacking. Research by the Bureau of Mines has developed a multistage process for recovering or recycling over 93 pct of the Zn, Cd, Cu, Co, and Ni from this material. The stages involved are (1) wet sizing, (2) H2S04 leaching of undersized material, (3) H2S04-Mn02 leaching of H2S04 leach residue, (4) selective precipitation of As, Cu, and Co-Ni products, and (5) precipitation of manganese for recycling to the leach circuit. The final process residue is only 1.6 wt-pct of the initial cake and consists of lead sulfate.

Jan 1, 1981

By L. H. Banning

Recent dry-top electric smelting tests at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., indicate that a high-titanium slag and a good grade of pig iron can be produced from alluvial Idaho ilmenite. A total of 120 tons of concentrates were smelted during this investigation, to yield an average of 0.5 ton of slag and 0.3 ton of pig iron per ton of ilmenite. Power consumption averaged 1,400 kv.-hr. per ton of ilmenite, at a feed rate of 400 to 500 pounds per hour, when operating at an electrical energy input of 290 to 370 kilowatts. The optimum operating voltage appeared to be 110 volts, phase-to-phase. Graphite electrode consumption averaged 15.6 pounds per ton of ilmenite smelted. Magnesite furnace refractory withstood the corrosive action of the hot metal and slag better than carbon refractory.

Jan 1, 1955

By B. K. Cantrell, K. L. Rubow

"Two source apportionment techniques have been applied by the U.S. Bureau of Mines to aerosol measurements in diesel-equipped underground noncoal mines. The first technique is based on size-selective sampling and the premise that the diesel exhaust fraction of the aerosol is predominately submicrometer in size while the mineral dust fraction of the aerosol is mostly supermicrometer in size. The second technique, chemical mass balance (CMB) modeling, was used to referee the analysis of diesel and mineral dust aerosol concentrations with the size selective method.The size-distribution data were modeled using a lognormal regression to parameterize the submicrometer and supermicrometer fractions of the sampled aerosol and to estimate the mineral and diesel contributions to each. Using this analysis, 97 ± 2 pct of the submicrometer aerosol mass was attributable to diesel exhaust aerosol.The CMB analysis, applied to both fractions of the respirable mi11e aerosol, yielded the amount contributed to each by the diesel and dust aerosol sources. On the basis of this analysis, 94± 10 pct of the submicrometer fraction was diesel exhaust aerosol. As much as 20 pct of the diesel aerosol, however, was found in the supermicrometer fraction, requiring a correction of the submicrometer fraction results to account for the missing diesel mass. More accurate measurements will require a carbon-specific analysis of the aerosol.INTRODUCTION Measurement of the contribution of diesel exhaust to respirable aerosol in mine environments has become increasingly important because of current concerns over the occupational health effects resulting from exposure to diesel emissions. In response to this, the U.S. Bureau of Mines is developing and evaluating new sampling methods for measuring diesel aerosol in underground mines. Two such techniques are being studied by the Bureau, size selective sampling and CMB modeling. These techniques use measurable physical or chemical characteristics of a mine aerosol sample to infer the amount of diesel particulate material contained in the sample."

Mar 1, 1992

By Gregory J. Chekan

The U.S. Bureau of Mines is investigating longwall panel and gate road layouts to increase coal recovery and reduce multiple-seam interactive problems. This report presents design practices for longwall mining multiple seams to provide mine planners and operators with practical guidelines for designing productive longwall mines. Key aspects of mine design that control longwall interactions are examined, including sequencing of seams, design of gate road pillars, and orientation of gate roads and longwall panels. Theories that describe stress transfer between multiple scams and the mechanics of interaction are addressed in relation to geology. Common longwall designs were further investigated using a boundary element model, MULSIM/NL. The model provided insight into relative stress transfer and distribution that occurs between longwall operations in multiple seams. Findings from the model show that (1) a longwall panel should be mined from the gob to the solid coal of an overlying mine, because the stress concentrations are lower; the approach angle should be kept under 30°; and (2) when mining in descending order, superpositioning gate roads usually produces the worst stress condition. To prevent this, the overlying isolated gate roads should be positioned from the centerline toward the headgate side of the underlying panel.

Jan 1, 1993

The Florida phosphate industry currently produces more than 80 pct of the total U.S. marketable output of phosphate rock. Because phosphate is one of three principal nutrients used in formulating a complete fertilizer, it is imperative that an uninterrupted supply of this material be available to meet the agricultural requirements of the United States while maintaining a viable phosphate industry which is competitive in world markets. As a result of an evaluation made by the Bureau of Mines, five areas were identified that affect the overall production and projected growth of the phosphate industry in Florida. These areas relate to the technological ability of the industry to comply with environmental regulations and performance standards by using the best available technology. The most significant technical problem facing the industry is the management of the clay fraction rejected during the beneficiation of phosphate ores. Other areas of concern are environmental restrictions and regulatory requirements, issues associated with mining and reclamation of wetlands, reclamation of other disturbed lands, and consumptive water use. Each of these areas is reviewed, with major emphasis placed on the current state-of-the-art processes for treatment and management of phosphatic clays.

Jan 1, 1983

By Philip C. Good

Unweathered low-grade calcareous phosphate rock of about 20 percent P205 grade was beneficiated by a procedure in which contained carbonates were decomposed by calcination at about 1,000° C. On quenching the hot calcined rock in water, major impurities passed into a slime phase which was mechanically separated from a coarser concentrate fraction. Phosphate rock of two major types was beneficiated in batch-scale studies yielding concentrates containing 31.3 to 38.5 percent P205 at recoveries ranging from 54.8 to 86.0 percent. The samples were from two major deposits in India. Processing information gained was utilized in extending the work to a continuous-flow system, processing phosphate rock at rates up to 157 kilograms per hour. Superphosphate exceeding 16 percent water-soluble P205 was prepared from concentrate derived from continuous-flow processing.

Jan 1, 1976

By Manuel Gomez

Coking time was investigated as a function of coal properties, carbonization parameters, and the interactions between these variables. The results indicate that coal properties and carbonization conditions interact to influence the coking time, and these interactions may be determined quantitatively. Prediction equations were developed and used to simulate the effects of bulk density, flue temperature, and oven width on coking times for coals having a wide range of properties. The data presented provide additional information on the carbonization process to permit the coke oven operator to maintain closer control of coke production and coke uniformity.

Jan 1, 1968

By Richard H. Singleton

Native asphalt was produced in 1978-79 by six companies in four States. Leading States were Texas and Utah. Output in-creased 37% in 1978 to 1.7 million tons and decreased 5% in 1979 to 1.6 million tons while value increased 39% in 1978 to $19.3 million and 33% in 1979 to $25.6 million. Bituminous limestone was produced by Whites Uvalde Mines and by Uvalde Rock Asphalt Co. in Uvalde County, Tex.; by Southern Stone Co. in Colbert. Ala.; and by Barton County Rock Asphalt Co. in Barton County, Mo. The product was used mainly in street and road repair. Gilsonite was produced by American Gilsonite Co. in Uinta County, Utah, and by Ziegler Chemical and Mineral Corp. in Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1980

By C. Q. Cupps

n view of increased interest in secondary recovery of oil in the Cut Bank field, Montana, a review has been made of unpublished data obtained during a 1943-44 study of reservoir oil characteristics in this field. Considerable uncertainty was attached to interpretations of subsurface oil sample analyses from six Cut Bank zone wells, one Lander sand well, and one Moulton sand well, because of adverse sampling conditions and wide range in the data. Much of this uncertainty has been removed by this review which has shown two of the Cut Bank zone samples and the Moulton sand sample to be representative of the reservoir oils. Estimates of original reservoir oil characteristics derived from differential-liberation analyses of these samples show that the oil in the Cut Bank zone was initially saturated at the gas-oil contact pres-sure, 750 psia, and the oil in the Moulton sand was undersaturated with a saturation pressure of only 380 psia. The rest of the samples were indicated to be nonrepresentative of the reservoir oils because of a disproportional vaporization of heavier components of the solution gas. The vaporization of these components is believed to be a cumulative effect of contact of the oil with bypassing, light-gravity gas which had been liberated at higher pressures from solution in oil farther back in the formation, or which had come from the gas cap, rather than from the singular effect of gas evolution caused by excessively low bottom-hole pressures. Change of oil composition caused by the latter was found to conform closely to that occurring during a differential liberation of gas in the laboratory.

Jan 1, 1967

By M. Vanpée, H. G. Wolfhard

Jets of hot gases issuing into explosive gaseous mixtures are efficient agents of ignition . The ignition temperature is defined as the temperature of the jet as it enters the cold explosive mixture which is just high enough to produce ignition . Such data have been published recently.5/ The investigators note especially that no correlation seems to exist between hot - gas ignition temperatures and spontaneous ignition temperatures , although there is a rather loose relation with limit flame temperatures . Before a more quantitative theory of the hot - gas ignition process can be attempted effectively , several questions must be answered : ( 1 ) Can the reactions leading to ignition be described by an Arrhenius type activation energy? ( 2 ) Is ignition preceded by an induction period ? ( 3 ) What is the rate - determining process of the ignition ? (4) And how does turbulence affect this type of ignition ?

Jul 1, 1960