Search Documents

By Gary E. Sherman

This report presents a Bureau of Mines study on the cost of mine permitting and compliance with environmental regulations in Alaska. It discusses permitting requirements and procedures for placer and lode mines. Placer miners must comply with recently established (1988) water quality regulations and effluent treatment requirements. To estimate the impact differing treatment options (no recycle, 100% recycling, and flocculation) have on a placer mine's rate of return, three models (1,500, 1,000, and 500 yd3/d) were simulated. Rates of return for these models show a marked decrease as effluent treatment is increased. The incremental increase in operating cost from one treatment option to the next is relatively small; however the opportunity cost of lost production if' significant and accounts for the decreasing rate of return with increased effluent treatment. Lode mines face greater costs for permitting and compliance than similarly sized placer mines as a result of the impact of the operation. Direct permitting costs for lode mines range from 2 to 6% of total project cost, with 4% the most common figure cited by industry. Total costs for permitting and compliance are approximately double those for permitting. Indirect costs associated with compliance include mitigation, monitoring, and reclamation.

Jan 1, 1991

By Stephen C. Tadolini, Steve Bessinger, James Pile, Christopher Mark

The San Juan Coal Mine, located near Farmington, New Mexico, supplies the San Juan Generating Station with more than 6 million tons of coal annually. To replace dwindling surface mine production, San Juan installed a longwall in 2002. The roof rock in much of the underground reserve consists of interbedded coals, carbonaceous shales, and mudstones. Roof support consists of fully-grouted roof bolts, both tensioned and non-tensioned, supplemented by modified cable trusses. Short-encapsulation pull tests conducted by San Juan’s geotechnical engineering department showed that some of the immediate roof layers provided variable bolt anchorage. To ensure that the roof bolts were obtaining the necessary anchorage, additional tests were conducted in a variety of locations. The results have been used to determine the optimum support design for different areas of the mine. Another series of tests evaluated the performance of several bolt and hole diameter combinations. The experience at San Juan Mine shows that short-encapsulation pull tests can provide the information necessary to improve ground control in variable roof conditions. It also illustrates how a pro-active geotechnical engineering program can be an essential component of a state of the art underground coal mine.

By Ronald S. Conti

The Bureau of Mines conducted a comprehensive laboratory study of the thermal ignitability of various carbonaceous dust clouds with particular emphasis on various ranks of coal dust. The tests were conducted using a new 1.2-L furnace. Autoignition temperatures of dust clouds were obtained as a function of coal volatility and particle size. Dust particles and gas samples were collected by a rapid-sampling system in order to study the reactions involved in preignition and postignition processes. The autoignition temperatures measured in the new 1.2-L furnace were significantly lower and therefore more conservative than those measured previously in the Godbert-Greenwald furnace. The combined effects of thermal and electrical ignition of dust clouds were also studied in the 1.2-L furnace using electrical discharges of varying energies at ambient and elevated temperatures. The minimum spark energy necessary to ignite a dust cloud decreased significantly as the temperature of the dust cloud increased.

Jan 1, 1983

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944

By A. Livingston

This paper on mining practice at the Fresnillo silver mines is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of North America. Two classes of ore are produced at Fresnillo. A low-grade oxidized silver ore; end a complex-base sulphide are containing gold, silver, lead, zinc, and copper. This paper is confined to a discussion of operations relating to the production of oxidized silver ores. To date, more than 10 Million tons of this ore rave been mined. The present (June, 1931) daily production is 2,000 tons of ore, and approximately 600 men are employed in the mining operations.

Jan 1, 1932

By Joseph B. Cummings

"Occurrences of fluorite on the Packard property were first examined by an engineer3/ of the Bureau of Mines in July 1943 as the result of receipt of an application for an access road. In August of the same year the showings were examined by a geologist4/ of the Federal Geological Survey. The property was again examined by an engineer5/ of the Bureau of Mines in March 1944. This last examination resulted in a proposal that access be gained by construction of a truck trail and that the Bureau of Mines undertake to explore the fluorite showings.The truck trail was constructed by the Public Roads Administration, which began the work on February 17, 1945, and completed it 8 days later.The Bureau of Mines exploratory program was completed on May 16, 1945. It consisted of stripping overburden, trenching, test pitting, tunneling, sampling, and topographic mapping.In addition to being described in some detail, the extent of the work as well as results are shown in accompanying tables and figures.Mrs. Rhoda A. Packard, Mrs. Nora 1. Cline, and C. B. Pettingill, all of Tonto Basin, Ariz., own the property, which comprises four contiguous, unpatented lode mining claims recorded at Globe, Ariz., as the Walnut and the Bluebird 2, 3, and 4. The claims are situated in T. 6 N., R. 11 E., Gila County. David L. Roscoe of Tombstone, Ariz., holds a lease and option to purchase.Access to the property is by Highway 88 from Globe, 34 miles to Roosevelt, thence 24 miles by a graded county road along the west side of Roosevelt Lake to Tonto Basin. Here the Greenback Ranch road, constructed by the Forest Service and maintained by the county, crosses Tonto Creek and continues easterly to the foothills. The truck trail leaves the road 8.5 miles east of Tonto Basin and runs 2.5 miles in a southerly direction to the property. (Fig. 1.)The fluorite deposits lie in and along a small canyon in a rough, rocky area at an altitude of about 3,400 feet, Vegetation is scant and of the usual desert variety. The summer climate is dry and hot and the winter climate moderate. Rainfall at the Forest Service Station in Tonto Basin was 11.4 inches from May 1944 through March 1945."

May 1, 1946

By Martin Berman

Tables of 28 positions for all the transitions for nine common analyzing crystals for first, second, and third order reflections were compiled by the Bureau of Mines to facilitate elemental X-ray fluorescence analysis on multi-element systems. The tables are based on a compatible set of wavelengths for 2,346 observed X-ray transitions of the elements lithium to americium. The results are tabulated in order of increasing wavelength as well as by increasing wavelength for each element.

Jan 1, 1969

By Robert E. Johnson

1962 was the second year of recovery from the mild 1960-61 recession. The year-to-year gain in constant dollar gross national product, our most comprehensive measure of the country's economic performance, was 6.0 percent (from $447.7 billion in 1961 to $474.8 billion in 1962). The unemployment rate declined from 6.7 percent to 5.6 percent. Although it was a good year, there were still unused resources of labor and capital which implied that the economy was operating below its potential. The year-to-year change in the Federal Reserve Board (FRB) index of industrial production of 7.6 percent masked the fact that more than one-third of the growth took place within 196L The monthly index rose only 4.8 percent during 1962, from 114.3 in January to 117.8 in September. The fact that the economy as shown by the industrial index, rose rapidly in the first half of the year only to remain on a plateau of 119-120 during the second half, led some people to fear an imminent downward turn. This did not occur. Neither production nor consumption of mineral fuels advanced as fast as the total economy. But consumption showed more gain than production, 5 percent compared with somewhat less than 4 percent. Production of both crude oil and natural gas reached new highs while bituminous coal production was the highest in 5 years.

Jan 1, 1963

By Rexford D. Singer

The purpose of this study was to evaluate the current literature on the use of calcium chloride and ligninsulfonates as dust suppressants with respect to potential adverse effects on health or the environment. Calcium chloride poses little internal hazard to man and animals, but toxicity to vegetation in and around the area of application should be expected. The effects, however, should be considerably less than those observed from using calcium chloride as a road deicer. Except for trout, ligninsulfonates seem to pose little direct systemic toxicity problems in aquatic organisms, animals and man or any problem with local vegetation. Because of a greater volume of information on its use and effects, calcium chloride is recommended over ligninsulfonates.

Jan 1, 1982

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By W. W. Culter

"This paper is the outcome of thorough investigation into the value of the previous methods used for deriving production decline curves. It is highly important that methods be employed that are fundamentally sound and also practicably applicable. Six methods commonly used were studied. Some of these were found to be fundamentally in error; some save reliable curves but involved much work and time in the preparation; others gave reliable curves with less time and effort.It was found that of the methods previously employed the ""family curve"" method described in Bull. 134 Amer. Inst. Feb. 1918, pp. 499-500 by Lewis and Beal, was probably the most satisfactory. The now method given in this paper ploys the same principles as the ""family curve"" method, but is mathematical instead of graphical,The engineer and the oil man should carefully boar in mind both the use and the limitations of the average production curve such as is derived by the ""family curve"" method or other methods mentioned. Estimations of future productions or of underground oil reserves of a particular tract or well should be made from the production records of the tract or the well itself wherever such records are satisfactory. The use of the average curve of a district or field should be applied only to those properties or wells where there are not sufficient data to construct individual or tract production records, or where the productive life so short that a satisfactory individual record can not be obtained."

Jul 1, 1920

By Jon C. Volkwein

The Bureau of Mines and many member companies of the Industrial Sand Association have been working in several areas to reduce personal exposure to respirable dust. Areas investigated include ventilation, modification of hardware, moisture addition to the product, and improved housekeeping practices. Ventilation systems have been devised and shown to contain 100 pct of a tracer gas released within the hood. An industrial clean air island has been developed and shown to reduce dust levels 90 pct at the opera- tor's position, Modification of hardware on a bag filling machine has been demonstrated to reduce dust 83 pct at the machine operator's lapel. This particular development has been termed a significant advancement in the state-of-the-art of bag filling by industry representatives. Addition of moisture to dried product materials has been tested with results showing dust reductions of 90 pct are possible!, Control of the moisture addition method still needs refinement and costs may be prohibitive. Dust sampling results clearly show the benefits of housekeeping practices such as building cleaning and vacuum sweeping. Rotation of work schedules is also effective for reducing personal exposure.

Jan 1, 1985

By Glenn C. Reed

This report is one of a series describing investigations within the Missouri River Basin in Montana made by mining engineers of the Bureau of Mines Minerals Division, Region II. The primary purpose of these investigations is to provide information to agencies of the Department of the Interior and and others concerned with the planning of Federal power developments in the basin. The report contains such factual data as have been authorized for public distribution. The field investigations in Broadwater County were made during the late fall of 1948 and the summer of 1949. Virtually all known metallic mineral deposits and some nonmetallic mineral deposits within the county were investigated. However, some long inactive mines and prospects on which little or no information is of record may have been omitted inadvertently. Many of the mines and prospects have been inactive for extended periods. Most of the underground workings now are inaccessible. Because of such conditions, impressions gained by the inspection of surface features have been supplemented necessarily, where possible, by information obtained from Federal and State publications.

Jan 1, 1951

By W. A. Calhoun

"INTRODUCTION A letter from S. D. Strauss, vice president of Metals Reserve Company, Washington, D.C., dated May 22, 1945, to the chief of the Metallurgical Branch, Bureau of Mines, in Washington; includes the following: Because of the present critical shortage that exists in the supply of corundum required by certain industries in war production, the Reconstruction Finance Corporation, Mr. W. C. Keeley, Vice Chairman for Metals and Minerals, War Production Board, has recommended that the Reconstruction Finance Corporation though Metals Reserve Company, proceed with preliminary mill testing of the corundum ore in Gallatin County, Montana, and that the results of that testing be transmitted to the War Production Board. If the results of the testing work are considered satisfactory, Metals Reserve Company will then provide for the actual mining and milling of the ore for the production of corundum concentrates.Pursuant to the above stated recommendation by the War Production Board, Metals Reserve Company desires to make -use of the facilities of the Bureau of Mines testing plant at Rolla, Missouri, for conducting sink and float and other concentration tests on representative samples of the Montana corundum ore. Two, and possibly three samples of ore are to be tested which will have an aggregate weight of approximately 50 tons."

Dec 1, 1947

By Oliver C. Ralston, Dorsey A. Lyon

Volatilization in retorts has been, until recently, the only commercial process of producing spelter, hence the zinc mine operators have had to meet the terms of the zinc smelters in regard to the following requirements: (1) Minimum percentage of zinc the ore must contain; (2) the chemical combination of the zinc in the ore; (3) the proportion present of those elements that interfere with the suceessful recovery of the zinc when the ore is retorted. In consequence of these requirements, only a comparatively small proportion of the zinc ores mined can be shipped directly to the smelters.

Jan 1, 1919

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By Kenneth Wardell

Criteria have been fully developed for determining the optimum size of oil and gas well blocks. The criteria lead to the formation of well barrier pillars which are, of themselves, inherently stable and take account of variable mine roof and floor conditions. The criteria ensure, through considerations of ground movement, that strains transmitted to well casings, are within tolerable limits of casing specifications. The criteria cater for well barrier pillars in multi-seam mining situations and where previous old mining has taken place. The criteria maintain flexibility in being adaptable to local mine design situations. The criteria are applicable to proposed extraction thicknesses up to 15 feet at depths up to 2,400 feet. The criteria are related to producing wells and to abandoned wells. In the latter connection, various states of well abandonment are recognised.

Jan 1, 1980

By W. W. Adams

Reports received by the Bureau of Mines, Department of Commerce, from State mine inspectors, for November, 1930, showed that 219 men were killed in the coal mines of the United States during the month, an increase of 25 over the previous month and 33 over November, 1929. On the other hand the production of coal decreased, the output of 43,329,000 tons in November being 8,397,000 tons less than in October and 9,005,000 tons less than in November a year ago. The larger number of fatalities accompanied by a smaller output of coal resulted in a higher death rate4 per million tons in November than in the same month last year or in October, 1930. The November rate was 5.05, as compared with 3.55 for November, 1929 and 3.75 for October, 1930. The increase in the rate for the industry as a whole was chargeable entirely to bituminous mines,, as the anthracite mines had fewer fatalities in November than in either of the previous months to which reference has been made. Reports for bituminous mines alone 'allowed that accidents at class of mines resulted in a death rate of 5.12, based on 195 fatalities and a production of 38,122,000 tons. This rate indicated an increase of 55 per cent over the rate for October, of the same year, and 72 per cent over the rate for November, 1929. The October record was 146 fatalities and 44,150,000 tons, and that for November a year ago was 138 deaths and a production of 46,514,000 tons. Twenty-four deaths occurred at anthracite mines in November, 1970: the output of coal was 5,207,000 tons, hence the rate was 4.61 per million tons. During the corresponding month a year ago there were 48 deaths and 5,820,000 tons of coal produced, which indicated a death rate of 8.25. In October, 1930, the death rate was o.34; based on 48 deaths and 7,576,000 tons.

Jan 1, 1930

The compliance sampling method for coal mine dust in the United States has not changed appreciably in the last 30 years. A call for more frequent sampling with immediately available results is leading to new instruments that may supplement or replace the existing sampler. This report discusses two such instruments that provide immediate results of dust levels. The first, called the Respirable Dust Dosimeter (RDD), is designed to supplement the existing U. S. cyclone compliance sampling method. It uses the pressure drop across a filter to provide an inexpensive screening type of measurement. The RDD has been tested in the laboratory and a limited number of coal mines. Side by side testing has compared the RDD performance with personal coal mine samplers in triplicate area sample measurements. Results show that the differential pressure of specific filtration media can be an effective surrogate for respirable mass. Data show that there is a dependence on coal type and an effect of relative humidity. There also appear to be two distinct responses related to coal type. For specific coals the coefficients of determination, R2, are better than 0.9. For general use the detector tube, using laboratory generated calibration curves, can be used to estimate respirable dust levels. However, a calibration to a specific coal type may substantially improve the accuracy. Another sampler in development is called the Personal Dust Monitor (PDM). Designed to give compliance quality accuracy, the PDM uses the frequency change of a vibrating element to measure dust and give immediate feedback of results. Results of laboratory comparison of the prototype PDM sampler to personal gravimetric samplers indicate R2 values of better than 0.99 for three different coal types. Work is in progress to package the components into a person-wearable unit combined with a cap lamp system with a total projected weight of less than 1.4 kg (3 lbs).

By R. J. Matetic, David S. Yantek, David K. Ingram

The National Institute for Occupational Safety and Health (NIOSH) has investigated engineering noise controls to reduce sound levels in cabs on air-rotary drill rigs. A recent investigation revealed that some drillers are exposed to A-weighted sound levels exceeding 85 dB even though a cab is used. NIOSH studied the in-cab sound levels of one such rig. First, preliminary tests were conducted in a controlled environment using accelerometers and microphones with spectral analysis to identify the dominant noise sources for in-cab sound levels. The results indicate that vibration transmitted from multiple hydraulic pumps to the control panel produces a dominant spike in the sound level spectrum in the 400 Hz 1/3-octave band. Next, field tests were performed in a production environment to evaluate noise controls to reduce in-cab sound levels. It was found that utilizing hydraulic noise suppressors reduces the structure-borne noise transmitted to the control panel. Further, using hydraulic noise suppressors and enhancing soundproofing reduced the in-cab A-weighted sound levels by as much as 4 dB.