Search Documents

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010

By James Westfield

A brief résumé follows of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code fur Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous -coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reportin; to the Coal Mines Administrator any violations of the Federal Minis Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1960

By Albert L. Toenges

This circular deals primarily with the various methods of longwall mining used in some mines in certain districts of the Middle Western States. In some instances underground methods were considered comprehensively, and in others only the actual methods of mining and face advance were noted. Results obtained by the mines in output per man were compared only on the basis of an operating day, since idle time and number of men employed would not, be comparable due to the great difference between mines in different districts. Man-hours per ton per operating day are noted in a general way. Material and power costs are not included. ACKNOWLEDGMENT The information used in preparing this paper was obtained through the courtesy and cooperation of the presidents and other officials of the comparnies operating the mines described. The approval of the executive of each property was obtained for publishing this manuscript, and the accuracy was checked.

Jan 1, 1936

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By Andrew F. Conn

This report summarizes the results from the first year of an anticipated multiphase program to develop improved coal mining equipment which utilize the CAVIJET? cavitating water jet method. This laboratory parametric study demonstrated the advantages of cavitating jets over non­cavitating jets in cutting coal, by producing comparable slot depths at one-fifth of the operating pressure, at better than one-half of the spe­cific energy. These results suggest that CAVIJET-augmented mining devices can be developed with compact, low-pressure pumps. Thus, CAVIJET should be capable of operating with safer, lighter support equipment, while providing all of the advantages (reduction of dust and sparks, reduced damage to cutters) of conventional hydraulic mining methods.

Jan 1, 1976

By Chas. F. Jackson

The work of the Mining Division is divided among seven sections, each in charge of a supervising engineer, as follows: 1. Metal-mining methods section, the supervising engineer of which is also supervising engineer of the Southwest Experiment Station at Tucson, Ariz. 2. Metal-mining research section. 3. Nonmetal-mining section. 4. Coal-mining section. 5. Mine-ventilation section. 6. Mineral-industries survey section. 7. Electrical section. The names of the sections indicate broadly the fields covered by each, and in the following, pages the objectives and type of work of each section will be summarized briefly and their active problems listed. The work clone during the fiscal year 1937 will also be summarized.

Jan 1, 1937

By Donald L. Siebert

This profile study of the commercial secondary aluminum industry examines not only the elements that form the industry but also the technological contributions of each toward industrial growth. Concise descriptions of processing methods trace aluminum scrap from generating sources to marketable industrial and consumer goods. Economic and marketing appraisals are used to illustrate the impact that recent technology has had upon the secondary aluminum industry. Price, supply, demand, competition, and substitutes are selected as components of an economic model of the secondary industry and are used to illustrate the aggregate effects of technological changes. The final section is a conceptual look at the future in which sensitive economic indicators (such as die casting in the automotive and appliance industries) are examined as well as the problems of conserving mineral resources by retrieving secondary aluminum from solid waste.

Jan 1, 1970

By William R. Wayment, David E. Nicholson

The Bureau of Mines studied some physical properties of hydraulic backfills and their paramount characteristics , and made preliminary attempts to compact this type of material . The in- place density of hydraulic backfills affects the properties of strength , consolidation , and water percolation . Dense fills give better support than loose fills . In - place density properties themselves are affected by grain size , grain size distribution , and the particular conditions of sedimentation in a stope ( the amount of work the slurry water does to compact the material ) . Field sampling of in - place densities of fills presently used in four different mines and laboratory and underground compaction tests using a standard concrete vibrator show that the initial in - place density of the cohesionless fill material tested can be significantly increased by vibratory compaction .

Jan 1, 1964

By F. J. Palumbo

An electronic color-sorting machine was tested for recovering colorless glass concentrates from mixed glass products. The tests were made using glass recovered from unincinerated (raw) urban refuse and residues resulting from the incineration of refuse. The results of the study revealed that concentrates analyzing about 86 percent colorless glass could be recovered from mixed unincinerated glass containing 54 percent colorless glass material. Recovery of the colorless glass was about 62 percent. Color sorting the incinerated glass was somewhat more difficult. Multiple-stage processing was required to recover 59 percent of the colorless glass material in a product analyzing 89 percent colorless glass. The feed material analyzed 41 percent colorless glass.

Jan 1, 1971

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

By David M. Gullikson

As part of its program of petroleum production research the Federal Bureau of Mines has long been engaged in the study and development of systems of analysis of oilfield waters (8, 12, 20, 21, 22, 27, 30).21 However, many of the early chemical procedures developed by the Bureau and widely adopted by the petroleum industry are time consuming, and some are unreliable for determining certain constituents found in California oilfield waters. Because of the need for more rapid and more accurate methods having greater sensitivity with low concentrations of some constituents, a study has been made by the Bureau's Petroleum Research Laboratory at San Francisco, in developing new techniques and modifying previously published techniques for analyzing oilfield waters by flame spectrophotometric, potentiometric, and colorimetric methods. Test solutions were synthesized for testing the suitability and accuracy of the procedures, and the effect of interfering ions. These solutions contained known quantities of characteristic constituents of oilfield waters including sodium, magnesium, potassium, calcium, lithium, strontium, barium, sulfate, chloride, bromide, iodide, carbonate, bicarbonate and borates in a wide range of concentrations. The compositions of these synthetic brines are listed in table 22. Many California oilfield waters contain salts of petroleum-derived organic acids and several synthetic oilfield waters also were prepared to which large quantities of naphthenates or salts of petroleum acids were added.

Jan 1, 1961

By Susan Brink

The U.S. Bureau of Mines is investigating the potential of in situ leach mining a variety of Cu, Mn, and Au-Ag ores. Geologic characterization of ore samples from laboratory leaching experiments is conducted both prior to and after leaching to assess the effects of leaching on the chemistry, mineralogy, and texture of the rocks. The identification and chemical compositions of ore, gangue, and reaction products are determined by a combination of techniques such as reflected and transmitted light microscopy, X-ray diffraction, electron diffraction, electron microprobe analysis, and backscattered electron imaging with scanning electron microscopy. The distribution of the desired metal in various mineral phases can be illustrated using elemental X-ray maps. The potential of reactive gangue minerals to rob Cu from leach solutions is investigated with the aid of transmission electron microscopy. Porosity and permeability are measured to determine how effectively the host rock can transmit leach solution. Textural relationships between ore, gangue, secondary reaction products, and fluid channelways are determined by petrographic examination and are documented by optical photomicrographs and secondary electron imaging. Representative sample selection is described, and several epoxy impregnation and sample mounting techniques are discussed.

Jan 1, 1991

By Stephen M. Jasinski

This report describes the materials flow of mercury in the United States. It examines the mining and production of mercury and the manufacturing, uses, and ultimate disposal of mercury. Materials flowcharts were prepared for 1989 and 1990. An effort was made to include estimates for all major anthropogenic sources including fossil fuel combustion, waste incineration, and nonferrous metal mining operations. Mining and mineral processing released about 100 mt/yr of mercury to the environment in both 1989 and 1990. The combustion o ii fu1s released 175 mt/yr in the same years. The manufacturing, use, and disposal of products containing mercury accounted fix the release of 1,037 mt of mercury in 1989 and 938 mt in 1990. The manufacture of chlorine and caustic soda was a major source of recycled mercury, but it was all reused within the industry. Recovery from all waste products accounted for 36% of reported consumption in 1989 and 42% in 1990. The losses from manufacturing and end use have been declining, whereas mercury emitted from combustion sources has not been strictly regulated and will likely become the largest source of mercury releases to the environment.

Jan 1, 1994

By W. W. Adams

Every man-hour of work performed in and about the coal mines of the United States had a 2-percent heavier death load from accidents in 1938 than in 1937. This is an unorthodox way of stating that the death rate per million man-hours of exposure or employment was 2 percent higher in 1938 than in 1937, increasing from 1.74 to 1.78. Thus the average miner had a 2-percent greater chance of being killed in 1938 than he had in 1937. The average quantity of coal resulting from 1 man-hour of work increased 3.6 percent -from 0.615 ton in 1937 to 0.637 ton in 1938. The production of the average ton of coal was accompanied by a slightly smaller loss of life in 1938 than in 1937, the accident rate being 2.793 per million tons in 1938 compared with 2.833 in 1937.

Jan 1, 1941

By Chas. F. Jackson

The work of the mining division is divided between seven sections, each in charge of a supervising engineer, as follows: 1. Metal-mining methods section, the supervising engineer of which is also supervising engineer of the Southwest Experiment Station at Tucson, Ariz. 2. Metal-mining research section. 3. Nonmetal minim section. 4. Coal-mining section. 5. Mine-ventilation section. 6. Mineral-industries survey section. 7. Electrical section. The names of the sections indicate broadly the fields covered by each, and in the following pages the objectives and type of work of each section will be summarized briefly and the active problems listed. The work done during the calendar year 1936 will also be summarized.

Jan 1, 1937

By W. S. Landers

This bulletin is a detailed study of low-temperature, entrained-bed carbonization of a Texas lignite. The lignite studied was from the Sandow strip mine and is representative of the Rockdale formation of the Wilcox formational group. Carbonization was conducted in a continuous entrained-bed reactor at several temperatures in the 8801 to 1,52°C F range, and at air-coal ratios it the 0 to 10.30 scf/lb range (moisture- and ash-free basis). Carbonization rates ranged from 97.1 to 410.0 lb/hr (as-received basis), At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coal ratios, parts of the heat for carbonization was supplied externally. It was demonstrated that the entrained-bed carbonization of lignite is a complex reaction and that several variables, of which carbonization temperature, air-to-lignite ratio, and the average size of lignite are important, act together to influence both the carbonization yields and the properties of the resultant products, Process variables established by pant tests were used to design the industrial scale carbonizer operated at Rockdale, Texas, by the Texas Power & Light Company as agents for the Aluminum Company of America. Properties of the carbonization product obtained from the industrial scale reactor were essentially the same as those obtained from the pilot plant reactor operated under the same conditions.

Jan 1, 1968

By James C. Barker

The analytical variability encountered when sampling for platinum-group metals (PGM) was statistically evaluated during a 1983 study by the Bureau of Mines and the University of Alaska. Sampling procedures were designed to systematically incorporate commonly used reconnaissance exploration techniques under actual field conditions. Analytical variability was evaluated at each procedural step. Analytical data from each sample from a single deposit grouped relatively well around the calculated mean for that deposit. Standard deviations did not exceed 43 pct of the mean for any of the deposits; more commonly, the deviation was about 25 pct. Statistical treatment of the data by analysis of variance indicated the most important source of error is selection of the sample site. Two or more replicate samples appear necessary to adequately quantify the PGM content. Secondly, significant variation occurs during preparation of a pulverized split for fire assay. The optimum sample size was in the 11-lb range; larger samples did not appreciably reduce variability. Smaller samples generally indicated a higher degree of variability. Evaluation of the sample method suggested the common grab sample, if carefully taken, is a useful indicator of the general range of PGM concentration but potentially includes a considerable margin of error.

Jan 1, 1985

By Ann G. Kim

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, P A. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic? test and subsurface temperatures was not significant.

Jan 1, 2010

Underground coal mine tracked vehicles have been studied to determine the state of the art and how brakes might be added to the coal haulage cars. Specific areas of interest are: brake sys terns, couplers, car trucks and car handling procedures. Problems related to adding brakes to the haulage cars appear to be: the limited amount of room to mount the brakes on the cars, brake line connection between rotary dump cars, achieving desirable braking characteristics without over complicating the system and keeping the installation cost to a reasonable figure. This document combines the information contained in the first issue of the "State-of -the-Art of Underground Coal Mine Tracked Vehicle Brake Systems," BRL Report No. 6080, with that contained in a subsequent monthly report.

Jan 1, 1973

By Robert D. Saltsman

Two modes of seal application were identified, and promising state-of-the-art seals of both types -shaft and drum -were selected for initial rating by non-destructive testing. Only one shaft seal survived the initial test, and a search was made for other candidate seals including new seals. One new type of seal was found that gave promising enough operation, as both a shaft and drum seal, to be recommended for installation in prototype wet-head machines.

Jan 1, 1975