Search Documents

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In compliance with this request a preliminary review has been made of trends, in, the production and uses of block granite. Some unfavorable conditions, were, thus brought to light and certain suggestions regarding a. more orderly and consistent growth in the industry are herein discussed. The results of the study axe, presented in this report for the earnest consideration of the industry and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of twines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable, assistance through her wide knowledge of granite statistics.

Jan 1, 1931

By David R. Hanson

Transient electrical noise events pose serious problems for data acquisition systems used in monitoring acoustic emissions in laboratory and field environments. The U.S. Bureau of Mines has designed and constructed a trigger discriminator circuit for use in ultrasonic acoustic emission studies. Designed for use with signals in the frequency range of 50 to 400 kHz, the instrument examines .incoming signals for frequency content, amplitude, simultaneity, threshold crossings, and number of channels above threshold. If preselected criteria on these properties are met, a plus 5-V pulse is output that may be used to trigger a data acquisition system, allowing rejection of noise events that do not possess useful information. The system was designed for four input channels, but may be expanded to more channels with minimal design changes.

Jan 1, 1995

By R. L. Lincoln

The effects of adding from 1 to 50 atomic percent (a/o) to vanadium were investigated by the Bureau of Mines. Properties studied included as-cast and annealed hardness, microstructure, fabricability at room temperature and elevated temperature, tensile strength, electrical resistivity, and oxidation resistance at 625° and 800° 2. Additions of small amounts of hafnium resulted in lessened as-cast hardness, decreased electrical resistivity, impaired roll- ability, increased oxidation resistance, and greater tensile strength. Larger amount of hafnium caused greater as-cast hardness, increased electrical resistivity, further impaired rollability, continued increase in oxidation resistance, and lessened tensile strength. INTRODUCTION The purpose of this study was to determine the effect of hafnium additions on the properties of vanadium and to learn if this binary alloy had any special or unusual properties. This investigation is a part of a larger research project in which new and expanded uses of vanadium are being sought. Domes tic vanadium is found frequently in combination with uranium, and because of the demand for uranium as a nuclear fuel, there now exists a surplus of vanadium-bearing minerals and vanadium pentoxide as a byproduct of uranium production. Primary principles of conservation demand that greater use be made of this readily available surplus; finding suitable metals to alloy with vanadium to enhance its properties is one way to increase its utilization. This report is the result of an investigation of the effects on the properties of vanadium when hafnium is added in amounts from 1 to 50 a/o.

Jan 1, 1962

By R. R. Sayers

The increasing use of hydrogen fluoride (annual consumption now exceeds 500,000 pounds (1)4/) directly and its occurrence as a byproduct of the utilization of fluorine compounds in the mineral industries, especially in metallurgical processes and in the refining of petroleum products, has aroused interest in its toxicity, and a brief review of the literature, with special reference to the hazard of poisoning in the mineral industries, seems to be opportune. Recently, residents in the vicinity of aluminum plants have been complaining of injury to livestock and vegetation as well as to their own health from the gases discharged into the air during operation of the plants, hydrofluoric acid gas apparently being the offender. The comparatively recent utilization of hydrofluoric acid in the alkylation process for the production of high-octane gasoline has raised the question of the hazard of poisoning in the petroleum Industry. In addition, the use of fluorine-containing refrigerants has extended the potential al exposure outside of industry (2).

Jan 1, 1945

The low production rates associated with the underground metal mining industry have received considerable attention during the last decade. A number of significant technological advancements, in the form of new equipment, have taken place to improve the economics of ore production. Unfortunately, an extremely important factor in the equation -- the operator protection and safety -- continues to receive a low priority. The underground metal mining industry has one of the poorest industrial safety records in the United States. Equipment operators are constantly being placed in hazardous situations. Even one fatality is one too many. All of us bear the responsibility to eliminate it. This project is one of the important steps currently being undertaken by the U.S. Bureau of Mines to improve the operational safety of seven major pieces of ore handling equipment commonly used in underground metal and non-metal mines. The objectives of this study are; (a) to identify the existing hazards associated with the operation of the specific equipment, and (b) to recommend practical solutions that will minimize these hazards and reduce operator injuries. These recommendations are to be in the areas of equipment design improvements, additional operator protection and warning devices, equipment operating procedures and any modifications to the existing safety regulations.

Jan 1, 1975

By Engelmann. William H.

In pursuit of innovative methods to improve mining productivity, the Bureau of Mines is investigating the use of inorganic salts as drilling fluid additives for penetration enhancement. Laboratory diamond drilling tests were performed on Westerly Granite with aluminum chloride solutions and on Sioux Quartzite with aluminum nitrate and aluminum, calcium, sodium, and zirconium chloride solutions as drilling fluid additives. These drilling results were compared with the average drilling performance using distilled, deionized water on Sioux Quartzite (12 replicate tests) and Westerly Granite (3 replicate tests). Maximum in-creases in penetration per given time and bit life were obtained when drilling with zero point of charge (ZPC) concentration solutions of each additive. For Sioux Quartzite, maximum increases in penetration and bit life ranged from 96 to 115 pct and 64 to 99 pct, respectively. For Westerly Granite, maximum increases in penetration of 155 and 165 pct and bit life of 109 and 136 pct were obtained at or near ZPC aluminum chloride concentrations of quartz (7.3 x 10-7 mol/L AIC13) and alkali feldspars (1.1 to 1.5 x 10-6 mol/L AIC13), respectively. This simultaneous increase in penetration per time together with extended bit life should result in increased productivity and reduced bit costs.

Jan 1, 1987

By E. C. Lane

This paper is the second report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relating to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 31293. A third and concluding paper giving the results of other tests will be published as soon as these tests have been completed. The present paper deals with the data of the twenty-third semiannual survey presented in accordance with the revised specifications for United States Government motor gasoline. The sample numbers used are identical with those used in Report of Investigations 3129, with additional data included for copper strip corrosion (method 530.22).4 and sulphur content by the lamp method.5 Three hundred and twelve samples were collected and analyzed in this survey. Two hundred and seven samples were competitive-price gasolines and one hundred and five samples were premium-price motor fuels.6

Jan 1, 1931

By John B. Goodman

A LOW-TEMPERATURE carbonization assay test is described, and factual data derived from this test are presented. The test procedure outlined in this report incorporates a mild-steel retort of improved design, an accurately controlled method of heating, and a complete collection and condensation system for the solid, liquid, and gaseous products of carbonization. The test described establishes, under closely controlled conditions, the relationship of temperature to yields of products on carbonization. Noncoking or weakly coking coals and other carbonaceous material are particularly amenable to testing by the assay. Mass balances of 100 percent± 0.3 are obtainable by this test. It is believed that the efficiency of the test and the accuracy of the type data obtained have been materially increased.

Jan 1, 1953

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By J. L. Wiley

[NOTE. - P before the number indicates that the ab tract appears in patent section. Abstract numbers without. P appear in literature section. A Abietic acid, hydrogenolysis - 404 Acetone, recovery - P-4024 Acetylacetonate catalyst - P-3352, P-3664, P-6067 Acetylene, production - P-2556, P-3169, P-4064, P-4221, P-4222, P-5002 Acid catalyst - P-4584 Salts - P-4555 See also Specific acid. Acid treatment. See Procedure. Adsorption. See Hydrogen, adsorption. Agitation. See Equipment, agitators; Procedure. Alcohols: Decomposition -1128 Hydrogenation - P-3288, P-4743 In motor fuel - 1486]

Jan 1, 1952

By F. J. Wiebel

"INTRODUCTION As a result of a general survey of the iron-ore deposits of Califor¬nia, the Bessemer was one shown to offer possibilities of developing com¬mercial ore reserves. Surveying and exploring were done at the request of Congress for an investigation of raw materials for the production of steel.A wartime steel plant has been established at Fontana, San Bernardino County, and a backlog of iron-ore reserve for the maintenance of permanent steel industry on the West Coast will be of National benefit in the postwar period.W. D. McMillan, a mining engineer the Bureau of Mines, examined the property in May 1942, and it was reexamined by D. W. Butner, also of the Bureau, in October 1943. Geophysical work was done by the Bureau in 1944, and the property was explored by diamond drilling from April to August 1944 and February to SeptemberACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, under the direction of R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

May 1, 1947

By R. H. Church, William E. Webb, Walter E. Pittman, James R. Boyle

As part of the Bureau of Mines health and safety research program, a short-range locator system, capable of locating miners who have become trapped following a mine accident, has been devised, The system consists of a lightweight, low-power radio transmitter incorporated into a miner's cap lamp battery and a directional receiver carried by rescuers. Prototype transmitters have been constructed, and the propagation of their signals has been investigated, The detectability of the signal in underground coal mines has also been investigated, This research indicates that a short-range location system would serve as an economical and practical means of locating miners from within the mine following an accident,

Jan 1, 1984

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

By G. E. McElroy

When mechanical ventilation is to supersede the natural ventilation of a mine it is desirable to determine what resistance the mine as a whole offers to the flow of air in order to specify properly the limiting duties of a ventilating fan. The relation of pressure to volume of flow for the mine as a whole may be calculated from experimental data, or it may be determined directly by measurements of volume of flow and the natural draft pressures causing flow; but in both methods the determinations are affected by many variables. With the intention of making a practical application of both methods, a small metal mine in process of development at Butte, Mont., was selected by the writers as the object of experiments planned to compare the mine resistances determined by measurements of natural draft and volume of flow with those calculated from experimental data. Four sets of teats were made with natural draft in October, 1925, December, 1925, April, .1926, and September to December, 1926; the last set consisted of a series of weekly observations. DESCRIPTION OF MINE The mine selected for the experiments was a typical vertical shaft metal mine in the development stage. No stoping had been done, and ventilation was confined to shafts, crosscuts, drifts, and raises. Figure 1 is a dia¬grammatic sketch of the main openings. All were timbered with full sets on approximately 5-foot centers. The shaft compartments were 4 by 4.5 feet, and one in each shaft was partly blocked by staggered manway landings. A pump column in the upcast shaft was discharging about 280 gallons a minute of water at 70° F. from the 1,000-foot level. The drifts were slightly sinuous, but the crosscuts were exceptionally straight and uniform in area; both drifts and crosscuts were about 5 by 7 feet in cross section. The raises were composed of vertical sections joined by frequent 450 offsets; each had three 4.5 by 4.5-foot compartments, of which two were plank-lined ore chutes and one was partly

Jan 1, 1928

By Sidney Katell

This report, covering the period January 1967 through December 1967, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the ninth in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week.

Jan 1, 1968

By F. Matanzo

[Nine wire rope terminations were pull tested and fatigue tested to destruction to measure the termination efficiency and relative fatigue life. The terminations were selected on the basis off mine site visits and the specimen were assembled in a manner similar to industrial slings. To measure a termination's sensitivity to poor workmanship, both standard and modified assembly specimen were tested. Lang and Regular construction of the 6x19 and 6x37 class wire ropes were used in diameters of 13 mm (1/2 in.), 19 mm (3/4 in.), 25 mm (1 in.), 38 mm (1 1/2 in.), and 51 mm (2 in.). In static pull tests rope class, construction, and diameter interacted with the termination to influence the efficiency of the termination. In axial fatigue tests using only the 6x19 class rope, the effect of rope construction was negligible since failure was primarily dependent on the termination type. The Swaged Socket, a termination requiring a high capacity hydraulic press, gave the best overall performance in terms of efficiency and fatigue life. The short body length of the Zinc Poured Socket (RR-S-550) was attributed with the short fatigue life of this termination. The use of thermosetting resins as a replacement for zinc was demonstrated successfully for some socket designs. The fatigue life of the termination, expressed as a percentage of the fatigue life of the wire rope, was shown to be a guide for the retirement of the wire in these applications where the wiry' rope is primarily in axial loading.]

Jan 1, 1978

By N. A. C. Smith, D. D. Stark

"Sulphur is apparently a normal Constituent of crude petroleum, but in most crudes is present in percentages of less than one-half of one per cent. Some crudes, however, contain more, and occurrences have been reported of heavy asphaltic oils with as much as five per cent of sulphur.Occurrences of Sulpher-bearing CrudesIn North America, the fields rest of the Mississippi River are almost entirely free from sulphur oils, the time oil from Northern Ohio and Indiana, and the Potrolia crude in Ontario, being practically the only ones which contain sulohur in amounts over 0.5. per cent. In the Mid-Continent district the production of high sulphur crude in general is small and unim¬portant. The two main excentions are the Healdton field in Oklahoma and the El Dorado field in Arkansas, both of which produce oils with considerable sulphur content. In the Wyoming field, one sand, the Ember Sandstone, pro¬duces a crude of high sulphur content, and it is probable that this crude rill be of considerable importance as production increases. At present, however, very little crude is produced from this formation. In the Gulf Coast conditions are irregular, some crudes being low in sulphur and others comparatively high. The same is largely true of California. The crudes of Mexico contain notable amounts of sulphur, and as they have been of great commercial importance in this country, a typical sample of light Mexican crude was selected for the present study. It is probable that the results obtained poly also (but to a lesser degree) to other sulphur-bearing oils. An analysis of this crude will be found in Table 3, also analyses of other typical sulphur-bearing crudes from different sections of the United States."

Mar 1, 1924

By P. B. Altringer

Searles Lake, CA, contains the largest known domestic tungsten resource. The brines in this near-dry lake bed, located in the Mojave Desert 130 mi northeast of Los Angeles, contain an estimated 135 MMlb of tungsten. However, the low concentration of tungsten (0.080 g/L W03) in the supersaturated brine makes selective tungsten extraction very difficult. Although many brine chemicals are extracted from the lake, tungsten recovery was an elusive goal prior to Bureau of Mines development of an ion-exchange technique. This publication describes the Bureau process. The following subjects are ad-dressed: ? The Searles Lake tungsten resource. ? General problems associated with tungsten recovery. ? Bureau research objectives. ? Synthesis of ion-exchange resins. ? Development of a two-stage ion-exchange tungsten extraction and concentration procedure. ? Product recovery and purification. ? Economic evaluation. Flowsheets for recovering three products (calcium tungstate, sodium tungstate, and tungstic oxide) are presented and evaluated, as well as a summary of the research effort and potential applications.

Jan 1, 1985

By R. W. Stahl

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to mineral industries' mines, quarries, and plants that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove that efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1963