Search Documents

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By A. W. Ambrose

The output or oil and gas rrom the producing fields in the United States is rapidly deelining. Coincident with this decline is a steadily increasing demand ror petroleum and its products, but at present there are no commercial substitutes ror gasoline and lubricating oil. Undoubtedly, many new fields will be discovered in this country during the next rew years. Indeed, there may be periods or temporary flush production that ror a rew months or a year or perhaps two years will afford a surplus. Such peaks are temporary and should not be given too much weight in considering the relation between petroleum supply and our national lire. In considering this problem we must regard a long period or time, and, ir we do that we shall see that domestic production will be unable to keep pace with consumption. Hence, the public good demands t~at the highest efficiency obtainable be practiced in the production or oil. To accomplish this end, the operator or to-day should so organize his rorces ror development and production that he recovers every barrel or oil that can be recovered at a profit. This necessarily involves the use or eeonomical and scientific methods or development a:nd production and the elimination or waste. The Bureau or Mines has ror years urged the conservation or petroleum and its products, and has pointed out that -such conservation should start before the oil is brought to the surface rather than arter it is in storage tanks. Losses or petroleum underground have undoubtedly been rar greater than losses in storage, in transportation, and in refining. The quantity lost usually is indeterminate, and hence difficult to express in terms or money, but by remembering that entire oil fields have been ruined by invadIng waters some idea may be gained or the importance or underground waste. The petroleum engineer is coming to be recognized as an extremely important aid in the intelligent development or oil fields. In this paper an effort is made to outline ror the engineer and producer a field or work whereby science and engineering not only can but have been applied practically. The mining engineer has been the direct- ing hand in the development of mines, and it is being recognized more and more that the petroleum engineer has a similar function in developing oil properties. Thispaper aims to show the general method of procedure in studying underground conditions in producing oil fields and how such study may not only correct but even prevent great unnecessary losses. Such work provides the company with maximum insurance for the field against loss and is accompliphed at minimum cost and minimum risk. Throughout the paper reference is made to oil wells and oil fields, but to a certain degree many of the suggestions relating to oil wells are applicable in the care and protection of gas wells and in solving gas problems.

Jan 1, 1921

By J. R. Thoenen

This paper outlines briefly results of seismic measurements recorded in the vicinity of quarry blasting under practical operating conditions. The data cover field work done from January to the middle of August 1930, during which time records were made of 61 blasts in 19 quarries. Of the tests made, one was in biotite-gneiss, two in dolomite, two in a flintlike volcanic complex, three in gabbrodiorite, five in trap rock, and six in limestone. One quarry was in Alabama, two were in South Carolina, two in New York, four in Kentucky, five in Connecticut, and five in Massachusetts. Explosive charges ranged from 0.30 pound to 41,900 pounds, and the method of shooting varied from mud caps through hammer and wagon drill holes to churn drill holes and coyote tunnel shots.

Jan 1, 1937

By B. J. CROSS., Henry Kreisinger, John Blizard, C. E. Augustine

This bulletin presents the results of 36 tests made on a 468-horsepower Edge Moor boiler fired with pulverized coal at the Oneida Street Station of the Milwaukee Electric Railway & Light Co., Milwaukee, Wis. The tests were made by the fuel section of the United States Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation. Illinois coal was used as fuel; the furnace, burners, and feeders were designed by the Locomotive Pulverized Fuel Co. The object of the tests was to determine what over-all boiler efficiency could he obtained with pulverized coal under various conditions of furnace operation and with coal of different fineness and moisture content. The investigation was thorough. The pulverized coal, as it was supplied to the furnace, was weighed in specially designed tanks placed on platform scales. Twenty-nine of the tests were of 24 hours duration, three of 16 to 18 hours, and four of 12 hours. All tests are reported excepting two-8 and 20-which had to be stopped abruptly, No.8 because a motor actuating the coal-feed screw burned out and No. 20 because of trouble with the feed pump. Tests 1 to 27, inclusive, were made with round burners and tests 28 to 3Rwith spreading burners. In the first nine tests a large excess of air was supplied in an effort to prevent the ash fusing at the bottom of the furnace. In tests 10 to 16 the supply of excess air was reduced in order to get a high efficiency, regardless of the slagging of ash at the furnace bottom. Tests 17 to 27 were made with a water screen about 10 inches above the bottom of the furnace, to make possible the burning of coal with a small supply of excess air without the ash fusing at the bottom of the furnace. Tests 28,29, and 30 were made without the water screen and with a small supply of excess air, and tests 31 to 38 with a water screen around the walls near the bottom of the furnace. Tests 32, 33, 34, and 35 were run with coarser coal than that used ordinarily at the plant. Tests 36,37, and 38 were made with undried coal.

Jan 1, 1923

By J. L. Morning

During recent years, the Bureau of Mines has conducted an extensive investigation of the materials for making iron and steel. This work includes iron ore concentration, agglomeration, direct reduction of iron ores and concentrates, the production of pure manganese, chromium, and cobalt by electrolytic processes, the production of ferroalloys from low-grade domestic ores, and the development of special alloys to utilize these products. As a part of this general program, a Congressional appropriation allowed the con¬struction of an electric-furnace, semicommercial, ingot-producing plant at Shasta Dam near Redding, Calif. The primary objectives of the pilot plant were to determine the costs and operating problems involved in the production of steel and ferrous alloys in which sponge iron was used as melting stock, and to determine the physical properties of the materials produced. The pilot-plant equipment and the results of sponge iron-melting tests in the basic lined, electric arc furnace have been reported in previous publications.3/4/

Jan 1, 1953

By John R. McWilliams

The technological and economic pattern of the U. S. mining industry has undergone a rapid and continuing change since World War II. To provide realistic up-to-date cost data and to disseminate knowledge of technical developments, the Federal Bureau of Mines, with the cooperation of individual mining companies, is presenting a series of mining methods and costs reports similar to those it issued before 1939. Shaft sinking has always played an important part in mine development and [ration] and is an appropriate subject for this series of reports. Shafts [are] especially important in areas such as the Coeur d'Alene district of Idaho, where every major mine is served by one or more shafts and shaft sinking is in progress at one mine or and her almost continuously.

Jan 1, 1960

By R. A. Beall

This bulletin reviews the historical background of the cold-mold arc-melting technology, with specific references to the development that led to homogeneous zirconium ingots. Descriptions are given of modern production arc-furnaces for vacuum melting of troth exotic and conventional metals. Besides zirconium, specific data are given for production of chromium, thorium, and copper. The development of the skull-casting technique for titanium is detailed, and the application of the technique to such refractory metals as molybdenum and tungsten is described. Factors of operation of the apparatus and furnace design are considered.

Jan 1, 1968

By A. J. Kraemer

This report is one of a series dealing with oil-shale-operations in foreign countries visited and studied by Bureau of Mines oil-shale technologists within the past 4 years. Many oil-shale deposits have been discovered in Brazil and studied with various degrees of thoroughness. In this report the major emphasis is upon the oil-shale concessions of Companhia Nacional de Oleos Mineraes, in the River Valley of the State of Sao Paulo, because this oil-shale deposit is one of the most promising in Brazil for large-scale utilization for the manufacture of liquid fuels and other products of oil-shale processing, and because the opportunity was afforded to examine the concession area and to study mining, retorting, and. refining operations on these shales. Results of detailed analyses at the Oil Shale Research and Development Laboratories of the United States Bureau of Mines, Laramie, Wyo., are reported, Analyses and other date dealing with other oil-shale deposits in Brazil have been compiled from many sources. As many data have been reported as could be correlated to indicate the range of variation of the several types of shale end similar material. The oil-shale deposits in Brazil differ widely in size, richness of the shale, and of the oil. Some deposits are situate& more favorably for exploitation than others.

Jan 1, 1950

By James W. Pennington

MERCURY, also widely known as quicksilver, ranks tenth in quantity in world output of nonferrous metals. However, its unusual and desirable combination of properties- liquid liquidity at ordinary temperatures, high density, uniform volume expansion, electrical conductivity, ability to alloy readily, high surface tension, chemical stability, and toxicity of its compounds -gives mercury an industrial and military importance out of proportion to the small physical size of the production industry. Although mercury has been known and used for over 20 centuries, until the 16th century consumption was small and chiefly in medicine. Since then mercury's applications have paralleled scientific advancements, kind current principal uses of mercury are in electrical apparatus, industrial and control instruments, agriculture, pharmaceuticals, and the electrolytic prepa¬ration of chlorine and caustic soda. Other materials may be substituted for mercury in come applications; yet, for those uses that require mercury's unusual combination of physical and chemical properties, there is no ideal substitute.

Jan 1, 1959

By Richard V. Ageton, Harry E. Tufft, E. A. Holbrook

When an underground excavation is made, the rock surrounding the sides and top of the opening is deprived of its natural support and tends to fall. Whenever caving takes place, the time and extent of the caving depend on the character and condition of the rock. In strong homogenous rock, such as solid granite, even a large chamber may stand indefinitely, whereas a soft material, such as clay or a loose material like unconsolidated sand, falls immediately if not supported. Weaknesses in the rocks induced by structural features, such as joints, :fissures, bedding and cleavage planes, and fractures produced by blasting, will cause the falling of insecure blocks or slabs unless means are provided to support these in place. In an unsupported mine opening, as a tunnel, the first slight settling or adjusting movement of the rocks (the "initial creep" or "set") is caused by the great weight of overlying material pressing down the rock masses above and around the roof and sides of the opening until they key together in roughly the form of an arch. The rock, after it has adjusted itself to this shape, becomes. selfsupporting. Timbering is necessa.ry in all mining only to support, therefore, those comparatively small blocks or pieces of rock which tend to loosen from the top and sides of the opening during or after the formation 'of the natural rock arch, and which lie between this natural rock arch and the opening. This statement, of course, has its limitations. For example; a layer of strong rock, like limestone, may act as a beam; then only the material under the limestone will need support. Timbering is not, as is commonly supposed by the layman, used to supp!ort the huge mass of rock between the back (roof) of an underground opening and the surface. It would be impossible to place enough timbers in a:ny underground opening to support such a mass. This fact is not'·perceived by all miners.

Jan 1, 1923

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By Chas. F. Jackson

This bulletin is one of a series of Bureau of Mines reports dealing with mining methods, practices, and costs. A study of this subject was undertaken by the Bureau in cooperation with a large number of mining companies in 1928. This study continued for 5 years, during which engineers of the Mining Division of the Bureau visited most of the larger mines and many smaller ones in the United States, as well as several mines in Canada and Mexico. As a result of this study, 75 reports dealing with underground mining methods and costs at different mines were published as information circulars. Circulars also were issued on 6 open-pit mines and 2 gold-dredging operations. These circulars were written by the managers, superintendents, and engineers in charge of the operations, in some instances in collaboration with Bureau engineers. They were prepared according to a standard outline drawn up by the Bureau to obtain uniformity in textual treatment and in the arrangement and basis of setting up cost and operating data.

Jan 1, 1936

By Joel N. Van Sant

THIS REPORT describes the occurrence, mining, and use of refractory clay in Colorado within Region III of the Federal Bureau of Mines, which includes the States of North arid South Dakota, Nebraska, Wyoming, Colorado, Utah, New Mexico, and Arizona. Field work by the Bureau of Mines, United States Department of the Interior, included examination of active and abandoned refractory-clay mines as well as a reconnaissance survey and sampling of numerous clay-bearing formations exposed in Colorado. Information from the survey and the sampling will help guide private industry in its search for virgin sources of refractory clay. Library research of published and unpublished reports from various Federal, State, and private sources was conducted during the early phase of the investigation. Most of the refractory clay mined in the Denver-Golden district of Colorado is not used for refractory purposes but is blended with other clays in the manufacture of structural clay products. The predominantly flint-clay de-posits in the Pueblo and Fremont County districts are mined and utilized chiefly in fabricating refractory products.

Jan 1, 1959

By W. C. Holliman

Commercial production of synthetic rubber in the United States became a reality in 1931 when E. I. duPont de Nemours, Inc., announced the manufacture of Duprene, a synthetic rubber made by polymerizing r chloroprene. Duprene was later improved and reintroduced as neoprene. Since 1931 other synthetic rubbers and rubberlike materials have been announced and are now produced commercially or are in the pilot-plant stage in the United States. These include Thiokol, Buna S, Perbunan, Koroseal, Vistanex, Flamenol, Ameripol or Hycar, Chemigum, Butyl rubber, and Flexon. None of these is synthetic rubber in the strict chemical meaning of the word synthetic, as none is identical in chemical structure with natural rubber. However, all possess some of the physical properties of natural rubber, and in addition usually have some outstanding property not found in natural rubber that makes them superior for certain uses. Because of these superior qualitites, a considerable demand had arisen for synthetic rubbers before the present emer¬gency, although the price was several times that of natural rubber.

Jan 1, 1943

By James V. Kelly

"INTRODUCTION In the course of Bureau of Mines investigations of iron ores near Scappoose, Columbia County, Oreg. during 1942, occurrences of laterite were noted in road cuts and outcrops at many localities in the county. In 1944, the State of Oregon Department of Geology and Mineral Industries completed a preliminary examination of alumina-iron-bearing laterite occurrences in Washington County north of Hillsboro, Oreg.3/ Their report suggested that the lateritic material might be amenable to treatment by the Pederson process for the commercial production of iron and alumina. In order to determine the extent and character of some of the reported lateritic occurrences, the Bureau conducted preliminary explorations in Columbia County near St. Helens, Oreg., from January through June 1945. Almost simultaneously the Alcoa Mining Co. began to explore nearby areas. Their work was continued and expanded after the Bureau's work had been discontinued. This report presents the data obtained from the exploratory work of the Bureau of Mines.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral re¬sources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.Samples were assayed at the Reno, Nev., laboratories of the Bureau of Mines under the supervision of A. C. Rice, acting supervising engineer, and at the Albany, Oreg., laboratories under the supervision of Dr. B. A. Rogers, chief, Albany Division, Metallurgical Branch."

May 1, 1947

By Jennifer A. Slatnick

Chlorofluorocarbons (CFC's), once universally accepted as ideal compounds for use in cooling and refrigeration, in foam production, and in cleaning electronic components, are being phased out and eventually banned under extensive international agreements because the chlorine in CFC's is thought to deplete the Earth's ozone layer. The industry has responded with the introduction of alternatives in the form of hydrofluorocarbons (HFC's), which contain no chlorine, and with hydrochlorofluorocarbons (HCFC's), which fill an intermediate gap in the replacement of CFC's. As a result of the elimination of chlorine in the HFC's and the reduction of it in the HCFC's, these alternatives contain more fluorine than the CFC's do. Other nonfluorocarbon substitutes, known as not-in-kind alternatives, contain no fluorine at all. As a result, the fluorspar mining industry, which is the source of fluorine in fluorocarbons through intermediate hydrofluoric acid, is being affected. Concern for this impact has led the U.S. Bureau of Mines to employ its capabilities to analyze various scenarios in the evolution of CFC replacements and substitutes to determine their effect on fluorspar mining. This report utilizes a network flow model to examine the effects of proposed replacements for CFC's, in terms of fluorine content, on fluorspar operations worldwide and on hydrofluoric acid plants in North America and Europe.

Jan 1, 1994

During the second quarter of 1983, the economic recovery showed further strength abetted by the performances of consumer spending, residential investment, and the slowing down of inventory reductions. Real gross national product (GNP) increased from the first to second quarter at an annual rate of 9.2 percent, compared with 2.6 percent from the fourth quarter of 1982 to the first quarter of 1983 and an overall 1.9- percent decrease in 1982. Total industrial production increased 1.8 percent in July, and productivity as measured by output per man-hour increased 1.3 percent between 1982 and the first quarter of 1983 (table 1). Especially noteworthy .was the performance of real consumer durable goods expenditures, which increased at an annual rate of 32.0 percent from the first to the second quarter (about half of the increase consisted of automobile sales) and real consumer spending, which increased between these periods at an annual rate of 9.7 percent. Residential investment increased at an annual rate of 76.1 percent between the first and the second quarters,1/ and private housing starts by about 38,000 units in both March and May.

Jan 1, 1983

By A. L. Engel

In previous reports5/ of ore-testing studies, teats made by established methods on typical ores selected as representative of certain mining districts have been described in considerable detail. In addition to established test procedures, such as screen analysis, Chemical analyses, microscopical examination of ores and products, sink-and-float separation, gravity concentration, floatation, and magnetic separation with or without roasting, it was sometimes necessary to apply other methods, such as leaching, in instances where physical separations were not feasible.

Jan 1, 1940

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate-mines in various foreign countries. This interpretation of the mining laws of Greece was prepared from information furnished by Ralph B. Curren, American assistant commercial attache, Athens, in reply to a questionnaire of the United States Bureau of Mines, transmitted through the courtesy of the commercial laws division of the Bureau of Foreign and Domestic Commerce. INTRODUCTION In his report,3 Mr. Curren states that the source of his information was the Director of Mines of the Greek Ministry of National Economy and the Mining Code of Greece, which was, compiled from existing laws in 1929,4 and which has since been modified by several acts of Parliament.

Jan 1, 1932

By M. D. Aldridge

The results of designing, constructing, installing and operating a ventilation monitoring system throughout an entire commercial coal mine is presented. Measured parameters were airflow, methane, carbon monoxide, temperature, relative humidity and differential pressure. A central computer provided for automatic system operation. Preliminary tests of two remotely controlled ventilation regulators were performed in conjunction with the monitoring system.

Jan 1, 1977