Search Documents

By R. S. DeCesare

Operation of the Bureau of Mines raw refuse continuous separation pilot plant is described, including modifications made to plant equipment for improved performance. Products recovered from refuse, many of which have been evaluated by other laboratories and private firms, are discussed. Sampling procedures used in the pilot plant and detailed data obtained from processing refuse from 13 municipalities are presented in appendixes. Fuel evaluations made on combustible fractions of refuse from the various municipalities are also presented. Information and data obtained at the pilot plant have been used to assist many municipalities in solving their urban refuse problems.

Jan 1, 1980

By G. A. Brady

Seven samples of Pennsylvania anthracite from the Bottom Ross bed were analyzed and tested to obtain data on cleaning characteristics, proximate and ultimate analyses, specific gravity, grindability, heating value, and ash softening temperature. Ash content of the samples varied irregularly from 9.0 to 34.4 percent, the range being narrowed to an upper limit of 14.8 percent ash by removing impurities dense enough to sink in a medium with a specific gravity of 1.90. Ash content of the sink material with specific gravity greater than 1.90 ranged from 56.4 to 80.4 percent; corresponding specific gravities were 2.095 to 2.534. Volatile matter contents were indicated to be higher for the ash-forming minerals than for the pure coal substance in the various specific gravity fractions of a given sample. Specific gravities of anthracites with compa¬rable ash contents but from different locations in the bed varied as much as 0.06. The grindability index increased significantly with increasing ash con¬tent of specific gravity fractions from all the samples.

Jan 1, 1968

By J. Burlin Johnson

In small-scale blasting experiments conducted in the Bureau of Mines laboratory, small charges were used to produce craters in blocks of concrete mortar. The results are compared with larger scale experiments of other research workers, and the comparison demonstrates the similarity of the results obtained and indicates that small-scale blasting should be a useful tool for predicting large-scale blasting effects. INTRODUCTION The purpose at this investigation was to conduct blasting experiments in mortar in the laboratory and then, by comparing the results with those from larger scale field blasts in rock to determine to what extent, if any, the laboratory results resemble those in the field. The work described herein was the initial phase of a project aimed at evaluating small-scale blasting as a tool for use in improving blasting techniques. It is evident from the stand-point of control and cost that small-scale blasting would be valuable in the study of rock fragmentation by blasting in mines and quarries, if the extrapolation is valid.

Jan 1, 1962

By J. R. Soule

"The fluorspar deposits in the Gallinas Mining District, Lincoln County, New Mexico, were examined early in February and again in April 1943 by the Bureau of Mines because of the possible importance of newly discovered deposits and of old mine workings showing fluorite-bearing material. There &re many of these deposits spread over a considerable area, and it appeared that exploration might indicate sufficient reserves to support a local mill that could contribute to the supply of fluorspar needed for war purposes. Accordingly, the Bureau initiated an exploratory program in June 1943, which was completed in August 1944.H. E. Rothrock, Roy Earhart, R. G. Smalley, and V. C. Kelly, geologists of the Federal Geological Survey, began mapping and studying the district in May 1943 and continued this work throughout the Bureau's exploration.David J. Stauffer, district ranger, U. S. Forest Service, and several claim owners assisted in the examinations and subsequent exploration.The fluorspar deposits in the Gallinas Mountains are reached by an unpaved forest road, which, leaves U. S. Highway 54 half a mile south of Gallinas station. The road runs due west for 3 miles, then turns due north just beyond the first cattleguard. This north branch is followed for 2 miles to a second cattleguard. There a left branch extends northwest up Red Cloud Canyon to the Red Cloud, and. All. American deposits; the right branch continues north for 2.miles past the Wade Porter ranch, to another left branch, which goes almost 2 miles west to the Hoosier Group deposits. The remaining deposits are reached by trail from either the Hoosier Group or, more easily, from the Red Cloud claim (fig. 1).The Hoosier Group is in sec. l9,, T.. 1S.,1 R. 12 E.; all of the other known ore occurrences are in secs. 13, 14, and 23 to 27, inclusive, T. IS., R. 11 E. All of the deposits are in the Lincoln National Forest and within the limits of a State game refuge. The nearest railroad loading point is Gallinas, Station on the Southern Pacific Railroad. Corona, the next station north of Gallinas, is a Mile or two farther from the deposits.Minor supplied, telegraph, telephone, freight, and express service, and limited living accommodations, Are, obtainable at Corona, 10 to 15 miles from the deposits of Carrizozo, N. Mex., 50 miles south."

Apr 1, 1946

By Alice V. Peter

Meerschaum or sepiolite is employed principally in tobacco pipes and cigar and cigarette holders, although a few other uses of minor importance are Down. The unique value of a meerschaum pipe is derived from the owner's pleasure in watching the color deepen with smoking and in having the color "set" at the desired shade. The name "meerschaum" (German for "sea foam") is applied because the material, when pure and dry, will float on water. Owing to its resemblance to the porous, bonelike structure of the cuttlefish, or septa, it is also known as sepiolite. There are a few scattered deposits of meerschaum in. the United States which have yielded a small product ion, but the world's supply of the' material is obtained fined principally from Asia Minor, Meerschaum deposits near Eski-Shehir, Turkey, are said to have been worked 2,000 years ago, but commercial exploitation is a development of the last hundred years DESCRIPTION AND PROPERTIES Meerschaum is a hydrous magnesium silicate (H4Mg2Si3010) having the following theoretical analysis: Si02, 60.8 percent; MgO, 27.1 percent; H20, 12.1 percent. It is a soft. (H.2 - 2.5), fine-grained, earthy, white, gray, or yellow material. It is very light weight when pure (specific gravity, 1 to 2) and is highly absorbent. Because of its porosity the proportion of water present in the mineral is affected by the humidity'of the atmosphere. In a moist atmosphere the water content may be as much as 21.7 percent. Then wet the material is soft and somewhat plastic. When dried again it becomes lard and tough. The toughness is especially apparent in some forms that have a fibrous or leathery texture.

Jan 1, 1934

By R. V. Ramani, W. Miola

"A relationship exists between the quartz contents in the underground coal nine airborne dust samples and those in the coal and host rocks that are mined [17, 18, 19] The prescribed method for quartz analysis in respirable airborne coal dust samples is the MSHA P-7 method. Accurate quartz analysis procedures are needed for bulk samples in order to predict the potential quartz content in airborne nine dust, which in turn will aid the design of quartz dust control procedures during mining. thereby reducing the airborne quartz dust in underground atmospheres. The requirements of this method are that the amount of quartz is the sample be less than 250ug, and the total sample weight less than 2,500 ug. Unlike with airborne dust samples, there are no limitations to the available mass of bulk samples. However, these are no standard procedures for the preparation of bulk samples for scanning or prescribed methods for quartz analysis. The NIOSH and MSHA methods are certified for roped* dust and the acceptance of these methods for bulk samples assumes that the bulk samples will be reduced to the conditions specified for respirable dust samples. An alternative method is X-ray diffraction, which provides higher average quartz values than those obtained from P-7 method for the same samples.An investigation was carried out to determine the optimal procedure for preparing the bulk samples for the IR and XRD analyses. In this paper, the investigations on the effects of calibration, particle sizes, matrix composition, interferrous, and behavior of the filter substances on IR, XRD and FTIR results are presented. The error introduced by the presence of kaolinite and a new sample asking procedure to reduce it are discussed. The problems experienced with conventional sample holders for scanning were eliminated with the design and development of a new hollow sample holder. Quantitative comparison of quartz determinations by IR, XRD and MR methods on coal, roof and floor rocks, and airborne dust samples are presented. The important factors affecting the results of quartz analysis methods are: 1) bulk sample preparation for obtaining representative and homogeneous analysis samples: 2) particle size distributions of the analysis samples and calibration standards; 3) qualitative matrix composition of the analysis sample; 4) matching calibration standards to analysis sample; 5) substrates for sample deposition during analysis sample preparation; 6) procedures for analysis sample mounting; 7) selection of proper portions of she response profile for insanity measurement; and 8) interferences of spurious phases with the critical analyses. The recommendations of this study are important to enable comparisons and interpretations of analysis and research results."

Nov 1, 1995

By Thomas M. Barczak

The transverse loading requirement for stoppings as specified in the current Code of Federal Regulations is 39 psf. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where the dominant parameter is the tensile strength of the sealant. A new protocol based on arching has been developed to determine the true transverse load capacity of stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid-arching of stoppings was developed and verified through full-scale in-mine tests. Using this protocol, a systematic study of the design parameters that affect arching capability in block stoppings was conducted. The study included a theoretical assessment of arching and development of design formulations that can accurately define the transverse load capacity of various stopping constructions under various loading conditions. This approach should lead to a safer mine environment by matching the transverse load capabilities of the stopping design to the requirements in the mine to ensure proper ventilation control is maintained.

Jan 1, 2005

By P. G. Clites

This study was conducted to determine the patterns of heat transfer to water-cooled copper crucibles during vacuum arc melting. Values of heat flux from the ingot to the crucible were determined during nonconsumable electrode vacuum arc melting of zirconium and during consumable electrode vacuum arc melting of titanium) zirconium) and steel. The results of these studies con-firm the existence of a high thermal resistance between the ingot and the crucible wall which results from the shrinkage of the ingot as the metal solidifies. Maximum heat flux occurs near the top of the ingot where maximum values of heat flux of 1.4 X 106 Btu/ft2 hr were observed during small-scale consumable electrode arc melting of zirconium and titanium. The maximum heat flux for consumable electrode arc melting of 8-inch-diameter ingots was 0.5 X 106 Btu/ft2 hr. The effects of electrode material) electrode diameter) arc current) and arc potential on heat flux from the ingot to the crucible were studied. Data were also obtained on crucible wall temperatures and on the effect of very narrow annular water jackets.

Jan 1, 1967

By Jacob N. Frank

A factorially designed, hydraulic fragmentation experiment using a high-pressure water jet was conducted on concrete blocks. Three levels of pressure, standoff distance, and impact angle and two levels of traverse time and surface condition were used. Three variables were measured: depth of penetration, volume of material removed, and width of slot. Three stepwise linear regression equations were developed from the jet parameters and the physical properties of the concrete. The three basic equations, describing the significant jet parameters and physical properties, were developed into 15 predictor equations, five for each variable investigated. Direct regression equations were also developed for each variable investigated to show the result of increasing or decreasing each significant variable. Energy efficiencies were developed for the experiment and for each significant factorial variable.

Jan 1, 1971

By Hendrik Gerritsen

The research to be described is directed to the construction of an instrument that detects methane in air. The principle on which it is based is that methane gas absorbs infrared radiation in the wavelength range of about 3.2 to 3.4 micron. Solid state p-n junctions of composition In, .97Ca.03As emitting radiation in a band centered at 3.3 micron were grown by liquid epitaxy on InAs. Fight separate growth cycles and a total of 200 diodes were measured to determine total power, wavelength peak, spectral. half width and reproducibility of the method. In order to compensate for temperature changes, dual emitter systems (one InGaAs, and one InAs diode) mounted on the same TO-5 header were made. These devices were imaged, using a folded optical path cell, on large area InAs detectors, grown by a planar diffusion technique. In the 0-50°C range the primary temperature sensitivity is in the InAs detector rather than in the emitters. Several methods to reduce the overall temperature sensitivity to within acceptable limits were demonstrated. Humidity was shown to have a negligible effect on the measurements.

Jan 1, 1976

Great strides have been made in recent years to reduce the disaster potential of underground mine fires. However, mines can still be caught unprepared for a fire emergency. Fires can grow too large before they are detected, warning systems can be too slow and uncertain to reliably signal the danger, and suppression systems can be inadequate to extinguish the flames. New mining systems and equipment may create unanticipated fire hazards, and new materials may generate highly toxic combustion products. This report contains papers that summarize recent significant developments from the Bureau of Mines mine fire protection research program relating to these problems. Certain of these findings are also applicable to surface mining operations. The papers fall into the general categories of fire detection and instrumentation, fire warning, fire suppression, diesel equipment, spontaneous combustion, and toxicity analysis of combustion products.

Jan 1, 1988

By J. S. Dunning

A primary goal of the Federal Bureau of Mines is to minimize the requirements for scarce mineral commodities through conservation and substitution of more abundant elements, such as iron and molybdenum. One example of this is the research effort to devise substitute materials for specialty alloys, thereby conserving nickel and chromium in high-volume stainless steels. As a possible substitute for the solid solution strengthening of chromium and nickel, the precipitation hardening characteristics of a number of binary iron-based systems in which Laves phase precipitates, such as Fe2Mo, are formed were investigated. Several hardening responses were observed, but none were ideal. The Fe-Ta binary system had the highest magnitude of hardening, even with low alloy additions, and the Fe-Mo system had unique stability at temperature. Accordingly, the Fe-Mo-Ta system was selected for study to determine if a ternary Laves phase could combine high hardening with long-term stability at elevated temperature. Hardening and stability were reflected in excellent elevated temperature, tensile, and stress rupture strengths. Future research will study ternary systems based on more abundant resource materials, such as the Fe-Mo-Ti system, together with additions, such as aluminum and minimal chromium, to provide oxidation resistance.

Jan 1, 1979

By Raymond B. Ladoo

"The increasing realization of the fire hazards involved in the use of wooden shingles caused the National Lumber Manufacturers' Association to beginsome five years ago a search for a suitable fire-resistant paint. The problem was submitted to the Educational Bureau of the Paint Manufacturers' Association of the United States and work was started by Mr. Henry L. Gardner at the Institute of Industrial Research, Washington D.C. in collaboration with Dr. Herman von Schrenk, a timber expert of St. Louis.The results of this,work have been described by Heckel, in ""Asbestos"", (Heckel G.B., Asbestos in the Paint Industry, Asbestos, Vol. 2, July, 1920,pp.- 5-10).,,who gives the following formula for one of the colors as typical: It will be noted from this formula that ""asbestine"" forms 33% of the total liquid pigment by weight or 31.8% of the solid constituents. Hockel in the article referred to describes this paint,as ""asbestiform"" and assumes since ""asbestine"" is magnesium silicate it must be the chrysetile variety of ""Asbestine"", however, is not asbestos but is a trade name for a fibrous variety of talc mined in the Gouverneur district, St. Lawrence County, New York. This rather natural error persists through the article and credits asbestos with many desirable properties which are characteristics of talc."

Aug 1, 1920

By T. H. Jeffers

Significant amounts of cobalt are present in readily accessible spent copper leach solutions. The Bureau of Mines investigated the feasibility of extracting cobalt from these solutions in a multiple-compartment ion-exchange (MCIX) column. The effects of aqueous flow rate, resin flow rate, column height, and compartment height on cobalt extraction were determined. Cobalt extractions of 92 pct or higher were achieved at solution flow rates of up to 5.5 gpm/ft of column cross-sectional area and an aqueous-to-resin flow ratio of 40:1. Overall cobalt extraction increased as the column height increased, but cobalt extraction per unit of length was more efficient in 8-and 12-ftco1umns than in an 18-ft column. Solvent extraction procedures were utilized to purify and concentrate the MCIX column eluates and produce a cobalt sulfate solution containing 70 to 80 giL Co. Metallic cathodes containing over 99 pct Co were e1ectrowon from this solution. Zinc, nickel, and copper byproducts were also recovered during processing of the ion-exchange eluates. Estimated total capital cost for a commercial-scale 10,000 gpm of a spent leach solution containing 26 million. With credits for zinc, nickel, and copper estimated net operating cost was $9.36/lb Co.

Jan 1, 1987

By D. E. Wolfson

The Bureau of Mines carbonized 21 coal samples from Fayette, Greene, and Washington Counties, Pa., at 900° C, using the Bureau of Mines-American Gas Association (BM-AGA) method, and determined yields of products and physical properties of the coke. These samples represented high-volatile A Pittsburgh, Sewickley, Waynesburg, and Upper Freeport and medium-volatile Upper Freeport and Lower Kittanning coals. About 20 percent of all coals presently carbonized in commercial coke ovens in the United States are mined in Greene and Washington Counties, principally from the Pittsburgh seam. Sulfur content of the Pittsburgh coals in these counties is moderately high (1.0 to 3.2 percent) but, because of extremely large reserves, accessibility to eastern United States markets and excellent blending characteristics to yield strong coke, these counties will continue to be an important source of metallurgical coals in the future. Most coals from the other seams contained more than 2 percent sulfur, which would limit their use as metallurgical coals.

Jan 1, 1968

By L. C. IlsLey

Coal mining is more widely distributed throughout the United States than is generally known, as 30 States are credited with having coal mines. In 1919 twenty-three of these States each produced at least a million tons of bituminous coal, and all the States produced about 560,000,000 tons. In addition, Pennsylvania produced about 85,000,000 tons of anthracite. Twenty-eight States have regulations prepared by commissions or have enacted laws governing the operation of coal mines. Pennsyl¬vania has separate codes for the anthracite and bituminous fields. The codes may be classified as follows: Twelve distinctly coal¬mining codes; eight codes that are essentially coal mining, but also apply to other mines; five codes that are subdivided, referring partly to coal mines and partly to other mines; and four codes that are essentially metal mining, but apply in part or in whole to coal mining. The first State to have a coal-mining law was Pennsylvania, which enacted a law, for Schuylkill County only, in 1869. The first State to enact a coal-mining law governing all the coal mines in the State was Illinois in 1872, followed by Ohio in 1873. Pennsylvania in 1879 enacted a law for anthracite mines only, but did not enact similar laws for bituminous mines until 1577. At least 10 other States enacted coal-mining laws between the years 1870 and 1890. Before 1890 electricity was little used in coal-ruining operations and therefore practically no provisions governing the installation, inspection, or maintenance of electrical equipment were made in any of the laws enacted up to 1890. In the law of Colorado, approved April 8, 1885, there is a reference to the use of telephones, probably the first reference to electrical equipment of any kind in a State-mining code. Most of the mining codes have been changed from their original form by amendment or by complete revision. In some of the early changes a casual reference is made to the use of electricity or to the handling of electrical equipment. In 1911 Pennsylvania added

Jan 1, 1920

By Edward F. Divers

This Bureau of Mines report describes the results of a laboratory evaluation of a mechanical dust collector (scrubber) suitable for underground coal mine applications. The scrubber was developed by the Mining Research and Development Establishment (MRDE), Burton-On-Trent, England, and tested at the Federal Bureau of Mines Pittsburgh Mining and Safety Research Center (PMSRC) as part of a technical exchange program. The 2,000-to 8,000-cfm scrubber consists of an electrically driven vane-axial fan, water sprays, a 2-inch-thick, loosely knit stainless steel wire filter panel, and a water droplet eliminator. The dust-laden airstream travels axially through the water sprays, filter panel, fan, and eliminator. Slurry water drains into a sump where a belt-driven pump recycles it back to the sprays. Fractional breakdown tests showed a maximum dust collection efficiency of 96 pct of respirable-size (less than 7 µm) coal dust at 2,000 cfm. Efficiency decreased with increasing airflow; for example, to 91 pct at 6,000 cfm. Following these tests the original wire panel was replaced with a similar but smaller panel developed at PMSRC; a marked improvement in dust collection occurred at all flow rates tested.

Jan 1, 1979

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow,VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

By Jürgen F. Brune, R. Karl Zipf, Michael J. Sapko

Seals are barriers constructed in underground coal mines throughout the United States to isolate abandoned mining panels or groups of panels from the active workings. Historically, mining regulations required seals to withstand a 140-kPa (20-psig) explosion pressure. However, the Mine Improvement and New Emergency Response Act (“MINER Act”) requires the Mine Safety and Health Administration (MSHA) to increase this design standard by the end of 2007. This report provides a sound scientific and engineering justification to recommend a three-tiered explosion pressure design criterion for new seals in coal mines in response to the MINER Act. Much of the information contained in this report also applies to existing seals. Engineers from the National Institute for Occupational Safety and Health (NIOSH) examined seal design criteria and practices used in the United States, Europe, and Australia and then classified seals into their various applications. Next, the engineers considered various kinds of explosive atmospheres that can accumulate within sealed areas and used thermodynamic calculations and simple gas explosion models to estimate worst-case explosion pressures that could impact seals. Three design pressure-time curves were developed for the dynamic structural analysis of new seals under the conditions in which those seals may be used: unmonitored seals where there is a possibility of methane-air detonation or high-pressure nonreactive shock waves and their reflections behind the seal; unmonitored seals with little likelihood of detonation or high-pressure nonreactive shock waves and their reflections; and monitored seals where the amount of potentially explosive methane-air is strictly limited and controlled. Figure 1 is a simple flowchart that illustrates the key decisions in choosing between the monitored or unmonitored seal design approaches and the three design pressure-time curves. For the first condition, an unmonitored seal with an explosion run-up length of more than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections exists. The recommended design pressure-time curve rises to 4.4 MPa (640 psig) and then falls to the 800-kPa (120-psig) constant volume (CV) explosion overpressure. For unmonitored seals with an explosion run-up length of less than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections is less likely. A less severe design pressure-time curve that simply rises to the 800-kPa (120-psig) CV explosion overpressure may be employed. For monitored seals, engineers can use a 345-kPa (50-psig) design pressure-time curve if monitoring can ensure that (1) the maximum length of explosive mix behind a seal does not exceed 5 m (16 ft) and (2) the volume of explosive mix does not exceed 40% of the total sealed volume. Use of this 345-kPa (50-psig) design pressure-time curve requires monitoring and active management of the sealed area atmosphere. These design pressure-time curves apply to new seal design and construction.

Jan 7, 2007

By Ernest L. Corp

The natural marine environment can be divided into four basic categories: the air-sea interface, the water zone, the seafloor, and the subbottom. Efforts are being made to accumulate data to delineate the conditions in each of these areas and to conduct engineering studies which will determine how these environmental parameters affect the mining process. Laboratory facilities have been constructed and equipment and techniques for scientific data collection and laboratory research have been developed. Major emphasis is being placed on studying the subbottom material. The objective of this emphasis is to study the engineering properties of marine placer deposits in order to assess their influence on the design and performance of the various mining subsystems involving penetration, excavation, transportation, and disposal. Presented are the results of engineering properties tests on a placer simulant which is currently being used for model and prototype testing of coring tools. The effect of these engineering properties on penetrability, core recovery, and sample recovery is discussed.

Jan 1, 1970