Search Documents

By Philip C. Tully

[This bibliography contains 3,655 different citations to technical and scienfic literature on helium and alpha-particles, abstracted by 13 abstract service iblicatlons during 1964. Multiple subject classification increases the total number of entries to more than 5,800. Helium citations are listed by 22 major assifications, alpha-particles by 12]

Jan 1, 1970

Alabama ranked 19th in the Nation in nonfuel mineral value1 in 1994, down from 18th in 1993, according to the U.S. Bureau of Mines. The estimated value for 1994 was $576 million, a 2.5% increase over that of 1993. This followed a 3.5% increase in 1993 over that of 1992. The State accounted for a little less than 2% of the U.S. total. Nonfuel mineral production in Alabama consisted entirely of industrial minerals; no metals were mined in the State. Bauxite materials mined in the State are a natural mixture of bauxitic clay and bauxite having very low iron oxide content and are primarily used to make refractory (high temperature resistant) products, rather than in the production of primary aluminum. In descending order of dollar value, the top four mineral commodities produced in Alabama were crushed stone, portland cement, lime, and construction sand and gravel. These commodities accounted for almost 88 % of the State's total non fuel mineral value, while crushed stone and portland cement together represented almost 65 % of the total. In estimated mineral production for 1994, Alabama remained first in common clays and first of only two States that produced bauxite; third in lime, kaolin clays, and fire clays; seventh in portland cement and salt; and was one of the top seven States that produce bentonite clays. The State dropped from third to fifth in masonry cement. Production of talc and pyrophyllite resumed in 1994. Compared with 1993, the value of crushed stone, lime, construction sand and gravel, common clays, kaolin clays, fire clays, bauxite, and talc and pyrophyllite increased. Decreases occurred in portland cement, masonry cement, industrial sand and gravel, and dimension stone.

Jan 1, 1995

By Wesley G. Holtz

A project to demonstrate the feasibility of retorting oil shale by the Paraho vertical retort process was carried out at Anvil Points, Colorado during 1974 to 1976. As a part of the demonstration project, laboratory and field tests were performed to determine the physical and chemical properties of the retorted shale for use in the development of eventual full-scale disposal plans. The material which exits from the Paraho retort is classified as a non-plastic silty gravel by the Unified Soil Classification System. The particles have an apparent specific gravity averaging near 2.60 and a mass specific gravity averaging near 2.00. The material can be compacted by normal laboratory and field construction methods to about 90 to 100 pounds per cubic foot dry density depending upon the degree of compactive effort applied. The addition of moisture does not improve compactibility appreciably. When high compactive effort is applied the retorted shale is classed as impervious to water flow. The compacted retorted shale exhibits shear strengths in the same order as those observed for silty gravel soils. If the compacted material is cured (long tune simulation testing) prior to strength testing considerable strength gain can be obtained from cementing action. The amount of cementing developed is dependent upon heat treatment and other operating modes of the retort.

Jan 1, 1976

By George A. Morgan

The 53 countries that constituted Africa in 1991 accounted for a significant portion of total world output of a number of mineral commodities. However, total output for the continent declined for many major mineral commodities produced compared with that of 1990. Also, Africa's share of total world output of these commodities generally declined. (See tables 1 and 2.) The most conspicuous declines were for cobalt and copper owing to mining and metal processing difficulties experienced by the world's two largest cobalt producers, Zaire and Zambia. Phosphate rock output declined primarily owing to a sharp fall in production from Morocco, also a leading world producer. Morocco's state corporation for phosphate production experienced marketing problems, leading to the decline.

Jan 1, 1993

By B. E. Blair

The physical properties and related geological and petrographic data for 81 rock types obtained from operating mines or selected test sites are presented in this report. Most of these rock data were obtained to supplement structural studies in underground mines; however, the data may be equally applicable to other problems where the physical properties of rock are an important factor. Stress-strain curves are presented, where available, and free medium velocities from laboratory and field measurements are compared for several rock types. Rock-type, geographical, and geo-logical indexes are included for reference relative to physical property data in this and previously published Bureau of Mines physical property reports. INTRODUCTION This report presents the physical properties of 81 rock types from 16 different projects (sections 53-68). Three previous physical property reports2 3 4/ (herein after referred to as parts I, II, and III) presented data on 244 rock types from 52 project areas. (Part I included sections 1-25, part II sections 26-36, and part III sections 37-52).

Jan 1, 1956

By John Ward Smith

This paper describes and evaluates a method that the Federal Bureau of Mines used to determine the ultimate composition of the organic material in 10 samples of oil shale from the Mahogany zone of the Green River formation in Colorado and Utah. Since interest has centered on the Mahogany zone, the richest section of the deposit, these 10 samples were chosen to provide a broad representation of this zone with the objective of obtaining generally valid ultimate composition values. The most probable organic composition for the Mahogany zone and the 95-percent confidence limits for each component average (in weight-percent of organic material) are: Carbon 80.5 ± .4 Hydrogen 10.3 ± .1 Nitrogen 2.4 ± .1 Sulfur 1.0 ± .1 Oxygen 5.8 ± .5 As only minor variations in composition were observed, the organic material of this particular bed is quite similar over a wide geographic area.

Jan 1, 1961

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961

By R. E. Kennedy

The presence in air of combustible cases and vapors can constitute an extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and allied industries, the Federal Bureau of Mines has investigated the flammability (explosibility) of various types of combustible atmospheres and has published Its findings. 4/ The explosibility of ethane has been studied, and its limits of flammability have been determined and published. The development of secondary recovery methods of stimulating oil production has intensified interest in the effect of high pressure on the explosibility of natural gas-air mixtures. The limits of flammability of natural gas-air mixtures at pressures ranging from 50 mm. Hg to 350 p.s.i.a. have been determined and published. More recently, the limits have been determined at pressures up to 3,00C p.s.i. in mixtures of natural gas-air-nitrogen.

Jan 1, 1950

By L. M. Demers, D. C. Kuhn

"Kuhn, Douglas C., and Laurence M. Demers. Effect of surfactant on basal and silica-induced eicosanoid production by the alveolar macrophage. Am. J . Physiol. 269 (Lung Cell. Mol. Physiol. 13): L165-Ll 70, 1995.-Infiammation and fibrosis subsequent to the inhalation of certain mineral dust particles has been suggested to result from the activation of eicosanoid synthesis by the alveolar macrophage (AM). To determine if surfactant modifies dust-induced generation of eicosanoids by the AM, we evaluated the effect of the surfactant lipid dipalmitoyl lecithin (DPL) on the production of eicosanoids by rat AM exposed to respirable silica dust in vitro. During the first 24-h exposure period, DPL alone significantly increased basal production of eicosanoids but completely inhibited silica-induced thromboxane A2 synthesis. In contrast, leukotriene B4 (LTB4 ) production was only partially reduced by DPL. During a second 24-h exposure period, LTB4 production in response to the highest dose of silica remained significantly elevated in the presence of DPL. Similar results were obtained when the surfactant preparation Survanta was evaluated. These results suggest that 1 ) DPL and Survanta independently activate AM eicosanoid production, 2) DPL and Survanta modulate the response of the AM to silica dust, and 3) L TB4 may be the most important eicosanoid mediator of the long-term effects of silica dust exposure on lung pathophysiology. THE OXYGENATED METABOLITES of arachidonic acid (AA) (here collectively termed eicosanoids) have been implicated as important regulators of lung physiology and are thought to be involved in pathophysiological sequelae such as acute respiratory distress syndrome, asthma, and the pulmonary complications of sepsis (20). This role is manifested through both direct effects on lung physiology as well as through an indirect modulatory effect on the release of other mediators of lung injury, in particular profibrotic cytokines such as the interleukins and tumor necrosis factor (15). Recently, exaggerated eicosanoid production by both the alveolar macrophage (AM) and the type II epithelial cell has been demonstrated to result from the exposure of these cells to several particulates, including crystalline silica (quartz) dust (5, 9, 17). These observations have led to the suggestion that eicosanoids play a major role in the etiology of pneumoconioses.Another secretory component of the pulmonary environment, surfactant, has been shown to modulate crucial AM functions, such as bactericidal activity and the recruitment of circulating immune cells (25). Indeed, an important feature of the lung's reaction to inhaled mineral dust is an increase in surfactant production, perhaps as a compensatory or protective response (1, 16). In addition, the alteration of the surface properties of mineral dust by surfactant or its components has been shown to influence the biochemical response of the AM to the dust, perhaps by altering the surface charge of the dust particle (11, 29, 32). And recently, Wallace et al. (28) have shown that the coating of mineral dust with surfactant, and its subsequent removal by lysosomal phospholipase, unmasks differences in dust cytotoxicity that are not apparent when AM are exposed to uncoated dust. Thus it appears that the inclusion of surfactant in in vitro exposure studies may be important in evaluating both the absolute levels of eicosanoid production by the normal and dust-exposed AM and the temporal relationship between dust exposure and the production of inflammatory mediators by the AM. Therefore, we characterized the effects of the surfactants dipalmitoyl lecithin (DPL; the primary lipid component of natural surfactant) and Survanta (a commercially available surfactant derived from bovine lung) on basal and silica-induced AM eicosanoid production during two 24-h periods after exposure to dust particles to both allow the enzymatic removal of surfactant from the particle surface and evaluate the k"

Dec 1, 1996

By R. B. Porter

Bench-scale tests were performed by the Federal Bureau of Mines on lignite and subbituminous coal at pressures to 1,000 p.s.i.g. (pounds per square inch gage) in atmospheres of hydrogen or nitrogen to obtain information concerning the influence of pressure on carbonization of normally noncaking coals. The distribution of gaseous, liquid, and solid products as a function of processing pressure was determined. Except for special experiments, the carbonization was at 940° F. In a hydrogen atmosphere above 400 p.s.i.g., agglomeration of the solid residue (especially with lignite) became noticeable and increased directly with the processing pressure. Although in some instances the solid particles fused together, the mechanical strength of the agglomerate was always low. On the basis of visual inspection, the coals agglomerated in the following order of decreasing intensity: (1) Steam-dried lignite; (2) lignite; and (3) subbituminous coal. Addition of lignite tar in quantities to 25 percent by weight of charge did not increase agglomeration or change the carbonization characteristics of the coal.

Jan 1, 1961

By W. C. Hudson

"Sillimanite, kyanite, and andalusite are aluminum silicates having the same chemical composition (Al2Si05) and are used in the ceramic industry for the manufacture of high-grade refractories. ""Natural sillimanite with added corundum or other alumina to just short of mullite 2SiO2) proportions is unequalled for jobs where strength at high temperatures, resistance to spalling, and resistance to slagging by acid slags is desired. High-grade porcelain ware also requires these minerals.""At the same cost, sillimanite would be preferred for most uses, but the lack of any large source of sillimanite has given economic preference to kyanite or andalusite for special refractories and high-grade porcelain ware.""3/The possible economic value of the sillimanite schist in the piedmont Plateau was first recognized by Dr. L. L. Smith, of the University of South Carolina, who published an article in the Engineering and Mining Journal, August 1943, on an occurrence of sillimanite schist in South Carolina.The Bureau of Mines was interested in developing a large source of sillimanite to relieve the shortage of high-grade refractories, and initiated a project to locate the ore-bearing areas in Georgia and South Carolina and to develop the most favorable ones.Two hundred and seventy-eight outcrops of sillimanite-bearing schists were found by a Bureau of Mines engineer.4/ The schist occurs irregularly throughout a belt extending from Talbot County, Georgia; to Spartanburg County, South Carolina, about 220•miIes long and approximately 15 miles in maximum width. The Bureau drilled four areas of the more coarsely crystallized schist in Georgia and South Carolina:In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon; chief; conducts preliminary examinations, performs the actual exploratory work; and prepares the final report. The Metallurgical Branch;.R. G. Knickerbocker; chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Sep 1, 1946

By J. Fletcher Smoak

Consumption of abrasive materials in the United States increased 22% in value over that of 1982 to $320 million; of which, 59% was manufactured abrasive, 35% was industrial diamond (natural and synthetic), and 6% was natural abrasive. Production value of natural abrasives, excluding industrial diamond, remained virtually unchanged. Production of crude tripol, a porous siliceous rock, decreased slightly; however, shipments of processed tripoli increased 13% in quantity and 32% in value. Production of garnet, an abundant iron-aluminum silicate, continued to increase primarily because of further increases in production from one plant that had completed an expansion program in late 1981. Production of special silica stone, both crude and finished, decreased in 1983 because of reduced demand for oilstones

Jan 1, 1984

By E. G. Noble

The effects of hydrogen chloride (HCI) concentration and temperature on the solubility and hydration state of the alkali chlorides LiCI, NaCI, and KCI and the alkaline-earth chlorides, MgCI2, and CaCl2 were investigated by the Bureau of Mines. Saturated aqueous solutions of the chlorides were sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increased HCI concentration caused decreased salt solubility be-cause of the common ion effect. Aqueous solubilities for the chlorides of Ca, Li, Mg, K, and Na ranged from 42.6, 45.2, 35.2, 25.5, and 26.1 pct, respectively, at 20° C to 56.9, 49.4, 37.6, 31.0, and 27.0 pct, re-spectively, at 60° C. In solutions sparged to HCI saturation, solubili-ties for these chlorides ranged from 22.4, 26.5, 3.0, 1.3, and 0.05 pct, respectively, at 20° C to 53.2, 48.8, 28.3, 2.6, and 0.8 pct, respec-tively, at 60° C. The solubilities of LiCI and CaCl2 in HCI solution were high because HCI solubility is low in these solutions. The chlo-ride salts of Ca, Li, and Mg formed hydrates, which depended on tempera-ture and HCI concentration. Monohydrates for LiCI, tetrahydrates and hexahydrates for MgCI2, and dihydrates, tetrahydrates, and hexahydrates for CaCl2 were obtained.

Jan 1, 1985

By A. W. Fahrenwald

The logic leading to the development of the experiments in this paper already has been stated in Part I,3 but is briefly as follows: The results of the batch-grind experiments in which time of "grind" and fineness of finished product were the variables, strongly indicated (1) that batch grinding involving a single grind could not be operated under any condition to give maximum mill efficiency, (2) that the, sieve analysis of the feed charge in the mill materially affected the efficiency of the mill, and (3) that the percentage of finished product in the mill is a vital factor in ball-mill efficiency. A laboratory closed-circuit grind technic designed to simulate present closed-circuit grinding suggested itself, in which: a ball mill and a classifier constitute the grinding unit. The features of the closed-circuit grinding system are: (1) Short large diameter mills, (3) rapid flow of pulp through the mill, (3) continuous automatic removal of finished product from the system, and (4) high circulating loads. The high circulating load is a result if the short length of the Mill - that is, of the time the charge remains in the mill - and the small percentage of finished material produced during each circuit of the feed through the mill.

Jan 1, 1930

By H. D. Raymond

This report contains a summary of designs, specifications, costs, and schedules developed for a prototype oil-shale demonstration mining program to be undertaken at the Horse Draw site in the Piceance Creek Basin, Rio Blanco County, Colorado. The objective of the demonstration program is to assess the feasibility of extracting oil shale and associated saline minerals from deep, rich oil shale zones which occur within the central portion of the Basin. Four mining systems were specified for demonstration. These include (1) chamber and pillar mining with backfill; (2) sublevel stoping with backfill; (3) sublevel stoping with full subsidence; and (4) block caving. Commercial-scale designs for each system were modified and scaled down as required to achieve program objectives. The demonstration mine layout and design includes specifications for ore handling, backfilling, ventilation, dewatering, maintenance, and supply systems. A feature of particular interest in the design is the combination of block caving and sublevel stoping methods into a single unit for demonstration of subsidence mining systems in deep oil shale deposits. The report also contains a detailed breakdown of projected capital and operating costs for the demonstration mining program.

Jan 1, 1979

By P. A. Bloom

Arsenic-containing flue dusts are currently being stockpiled by several nonferrous smelters in the United States. These stockpiles are a source of environmental concern since the dusts can be transported by wind and contain water-soluble arsenic. The stockpiles also represent an alternate source of metals. To provide a quality environment, the Bureau of Mines investigated a process to make environmentally acceptable the discard of arsenic obtained from the treatment of arsenical flue dust. The process includes (1) leaching arsenic from a lead smelter copper dross flue dust, (2) fixing arsenic as an insoluble compound, and (3) recovering other metal values. Overall results of acid-leaching tests on lead-smelter flue dusts showed that H2S04 dissolved 80 to 90 percent of the As, Zn, and Cd, and up to 86 percent of the In. Pb, Ag, and Au remain in the residue, which can be recycled to the smelter. Indium was recovered from the strong acid leach solution by solvent extraction; arsenic was fixed in a stable form by precipitation with Fe2(S04)3 and CaO or CaC03.

Jan 1, 1982

By A. Stawsky

Effective use of diesel vehicles in underground mining requires attention to improved control of diesel exhaust pollutants such as particulate (soot), oxides of nitrogen and sulfur and carbon monoxide. An experimental survey Is made of diesel emission aftertreatment control techniques including water scrubbers, catalytic converters, exhaust gas recirculation (EGR) and soot filters. Use of two or more techniques in combinations are tested for optimum control of all exhaust pollutants. Dynamometer data is developed for steady state and computer controlled simulated mines duty cycles operation of Deutz F6L-714 and F8L-413 engines. Exhaust Quality indices (EQIs) are calculated from dynamometer data for comparisons among the control combinations examined. The Corning diesel particulate filter (DPF) is shown to be the most promising and practical device. The Corning DPF in combination with EGR provided the best (lowest) EQI from the test data. Use of the DPF requires additional regeneration mechanisms such as a catalytic filter coating or fuel additives. A metal mine field test is made of DPFs on an operational scoop tram to test practical applicability. Further development is proposed for application to various mine conditions and for improvement of DPF regeneration techniques including coating with newly available catalysts.

Jan 1, 1987

By H. Reginald Hardy

This report is Volume I of a three volume final report on the micro-seismic monitoring of a longwall coal mine. Volume I deals for the most part with the detailed aspects of the microseismic field study itself, however, brief references are made to other secondary studies described in Volumes II and III. During this field study a mobile microseismic monitoring facility and associated transducers were employed to detect and record microseismic activity above a longwall panel at Greenwich Colleries, Barnesboro, Pennsylvania. The fundamental objectives of this study were (1) to evaluate the feasibility of detecting microseismic activity originating from longwall mining operations using an approximately planar, near-surface, geophone array installed above the longwall and (2) to attempt to locate the sources of the various microseismic events. This investigation has proven that, using the techniques developed it is possible to detect microseismic events at depths of more than 400 ft and at horizontal distances in excess of 800 ft from the source. The majority of the observed events were found to have frequencies on the order of 10 to 100 Hz, and particle velocities of 50 to 300 µips. When a suitable velocity model was utilized, most of the events located were computed to be within ±100 ft vertically of the coal seam and ±50 ft horizontally of the longwall face. The results of the overall research project suggest that additional research should be undertaken in a number of associated areas.

Jan 1, 1978

By John A. Kost

Previous work performed under Contract H0220003 suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error. Under Modification No. 4 additional surveys were made in twelve coal mines, representing six states. Same 2,500 samples were collected, analyzed for incombustible content, and statistically evaluated. The earlier findings were substantiated.

Jan 1, 1975

By John C. Machisak

INJURY DATA and experience at, coal mines in the United States for 1953 and 1954 are presented in this publication with a minimum of interpretation and comment because of the numerous tables required to afford detailed comparisons between the 2 years. Corresponding tables for 1953 and 1954 follow in consecutive order under the following general sections: (A) General injury experience: Tables 1 to 11: Contain current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity and time-loss rates. (B) Selected injury data: Tables 12 to 85: Contain current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines.

Jan 1, 1958