Search Documents

Construction workers may be exposed to hazardous dust containing crystalline silica during site preparation when drilling systems are used. The National Institute for Occupational Safety and Health (NIOSH) found that drill dust could be decreased by using wet or dry dust reduction engineering controls, enclosed cabs, and implementing a dust control program.

Jan 1, 2009

By P. -É. Boileau, M. Smets, T. Eger, J. Boutin

Long-haul dump (LHD) vehicles used in underground mining are known to expose workers to important levels of whole-body vibration1. These vehicles are generally designed without suspension and may be categorized as small or large LHDs depending on whether their respective load capacities are lower or larger than 3.5 cubic yards. While the majority of older vehicles are equipped with a rigid or unsuspended seat, more recent LHDs often incorporate a suspension seat. The objective of this study was to define the vibration spectral characteristics of most commonly encountered large and small LHD vehicles operating in mining operations. This was done in an effort to categorize the vehicles in terms of vibration spectral classes to be reproduced on a laboratory whole-body vibration simulator to assess the vibration attenuation performance of a typical LHD suspension seat. Methods Vertical vibration measured at the seat attachment point of 8 small and 8 large LHD vehicles operating underground in typical mining operations under loaded and unloaded conditions was considered as the basis for defining the spectral classes. By regrouping the data collected for each LHD vehicle size and load condition, the overall distribution of acceleration power spectral density (PSD) of measured floor vibration was determined over the 0.5 to 20 Hz frequency range. Mean and envelopes of maximum and minimum values of PSD spectra were computed to define the spectral classes, along with the corresponding values of frequency weighted rms acceleration determined in accordance to the ISO 2631-1 standard2. These spectra were further used to calculate the displacements needed to drive a whole-body vibration simulator consisting of a platform supported by two servo-hydraulic actuators having a total stroke of ±100 mm. For validation purposes, the vibration acceleration spectra measured on the simulator were compared with the target spectra representing the spectral classes. Finally, the vibration transmissibility characteristics of a typical suspension seat were determined under sine sweep excitation using both a rigid mass load and a human subject having a mass of 62 kg and 85 kg, respectively. The SEAT value, representing the ratio of seat to base frequency-weighted rms acceleration, was further measured under each of the defined LHD vibration spectral classes by loading the seat with an 85 kg subject. Tests were repeated three times and the mean SEAT values were determined to assess the seat’s ability to reduce exposure to whole-body vibration in LHD vehicles. Results Three spectral classes applicable to both loaded and unloaded conditions were defined as shown in Figure 1: one for large and two for small LHDs. The influence of load on frequency-weighted rms acceleration was found to be negligible for large and Class I small LHDs, while a shift of the peak acceleration PSD to lower frequencies was noted for the loaded vehicles. The influence of load was found to be more important for Class II small LHDs. Table 1 provides a

Jan 6, 2006

By James Ridenour

The Gearhart Mountain Wilderness and RARE II area 6225 encompass 22,823 acres (9,236 ha) of the Fremont National Forest in southern Oregon (fig. 1). The area was studied under the provisions of the Wilderness Act of 1964 (Public Law 88-577). The U.S. Bureau of Mines determined the mineral potential of known mines, prospects, or mineralized areas, while in a separate effort the U.S. Geological Survey made geological, geochemical, and geophysical studies. MINERALIZED AREAS The study area contains no mining districts or known claims. Nearby occurrences of uranium, base metals, perlite, mercury, and diatomite apparently do not extend into the study area. Reconnaissance pan samples reveal only trace amounts of gold. No anomalous economic minerals were found in heavy mineral fractions of samples from stream beds draining the area.

Jan 1, 1982

Overexposure to noise is a widespread, serious health hazard in the mining industry, and causes hearing losses to a large percentage of the mining population. Recognizing this fact, the Bureau has a major on-going research effort to address this problem area. These proceedings include an overview of the Bureau noise control program and summarize nine selected noise control research programs.

Jan 1, 1984

By Maria I. De Rosa

Analysis of mining equipment fires from 1990 through 1999 reveals that there were 340 large mining equipment fires, resulting in 72 injuries and five fatalities. Many of the fires resulted in the loss of equipment and all posed potential or real risks to the operator. In 97 cases, the fires raged out of control due to engine shut­off failure, even upon activation of the machine fire suppression system, due to the spraying of pressurized hydraulic flu­id and fuel onto hot engine surfaces. In other cases, even after engine shutoff, the fires re-ignited, fueled by the contin­ued flow of flammable fluids remaining in the lines onto the hot engine surfaces. In many of the fires, flammable vapors evolved and penetrated the cab, violently igniting, forcing the operator to exit under very hazardous conditions. The use of emergency evacuation lines in the fuel and hydraulic fluid systems, and methods to reduce or prevent the spraying of pressurized fluids onto hot engine surfaces would greatly improve the chances of successfully suppressing large mining equipment fires. In addition, the use of systems for preventing the ignition of flammable vapors inside the cab, and detecting and suppressing fires originat­ing in the cab, would greatly enhance operator safety. The National Institute for Occupation Safety and Health (NIOSH) recently conducted experiments on meth­ods to reduce the fire hazards associated with large mining equipment. These experiments evaluated the use of cab inerting systems to prevent the ignition of flammable vapors inside the cab and sup­press fires originating in the cab, while maintaining a breathable atmosphere for the operator to bring the equipment to a stop and safely exit the cab.

Jan 1, 2008

By R. Barany

The heats of formation of gehlenite and talc were determined by hydro-fluoric acid solution calorimetry. The results are reported in terms of the constituent oxides (?H298.15 = -31.1 ± 0.5 kcal/mole for gehlenite and ?H298.15 = -44.9 ± 0.3 kcal/mole for talc) and in terms of the constituent elements (?H298.15 = -952.8 ± 0.7 kcal/mole for gehlenite and ?H298.15 -1,415.5 ± 1.4 kcal/mole for talc).

Jan 1, 1963

By G. E. McElroy, A. S. Richardson

"The Bureau of Mines, in cooperation with the Anaconda Copper Mining Co., has conducted a series of experiments an air measurement in fan-pipe installa¬tions in a Butte mine during the fall and winter of 1922-3. The chief purpose was to determine the friction factors for different types and sizes 3f fan piping, but much attention was devoted to methods of air measurement, not only with respect to the methods used for friction factor tests, but also to com¬parison with other methods.The air flow was measured simultaneously at two points 380.6 feet apart in six different fan-pipe installations, each over 500 feet in overall length, in a rock cross cut adjacent to an air shaft,The air pressure was regulated by two sinoco multivane fans, driven by 7 ½ h.p. motors, the fans being connected in tandem so that one discharged into the intake of the other through a short connector and the latter discharged into the line through a straight connection equipped with a honeycomb of 4-inch squares or S radial vanes to prevent spiral flow of air, At each point where it was desired to measure the air flow, measuring sections equipped with piezometer rings pierced for easy insertion of pitot tubes, thermometers, etc. Piezometer static pressures were used in all the tests as standard, and dynamic or total pressures only were obtained with the pitot tubes, except for purposes of comparison.The tubes had special guide blocks, designed especially for underground work. To insure greater accuracy two tubes were used simultaneously, in order to obtain the velocity pressure at the center of the section simultaneously with that nearer the circumference, so that the mean velocity would be determined as accurately as possible. The tubes were held in proper place by means of flat guide boards. Velocity pressures were measured in manometers."

Sep 1, 1923

By D. J. Bauer

A pure scandium solution was concentrated from 10-4 mole per liter to 0.5 mole per liter by continuous foam fractionation in a spaced, packed column. Recovery in the foam was 77 percent using a spaced, packed draining column with sodium n-methyl-n-"coconut oil acid" taurate as the surfactant. The technique was first studied batchwise in a small unpacked column to determine the more important variables. Optimum surfactant concentration was found to depend on scandium concentration. Extraction and, in general, enrichment ratios were highest in the 2.5 to 3.5 pH range at temperatures ranging from 50° to 70° C. An airflow rate of 136 ml./min. was satisfactory in the equipment used.

Jan 1, 1962

By L. H. Adami

Heats of formation were obtained for four anhydrous crystalline sodium borates by hydrochloric acid solution calorimetry. The heats of formation at 298.15° K from the elements are NAB02, -233.2 ±0.6 kcal/mole; Na2B07, -786.4 ±1.0 kcal/mole; NaB305, -549.9 ±0.8 kcal/mole; and Na2B6013, -1,412.5 ±2.0 kcal/mole, The heats of formation from the constituent oxides are NaB02, -31.5 ±0.8 kcal/mole; Na2B407, -78.8 ±1.3 kcal/mole; NaB305, -44.1 ±0.8 kcal/mole; and Na2B8013, -96.7 ±1.5 kcal/mole.

Jan 1, 1968

Develop a mobile manipulator that one person can use to lift and maneuver 50- to 600-pound loads. It can be used in maintenance shops and mines to reduce lifting accidents (Figure 1 and 2). Background Lifting heavy items is one of the leading causes of injury in the workplace. Mine Safety and Health Administration statistics showed that, in 2004, back injuries accounted for over 20% of all injuries (1,699 cases) and resulted in 110,000 lost days of work. Forty-one percent of those injuries resulted from materials-handling or maintenance activities.1 In addition to back injuries, lifting injuries include hernias, ruptures, sprains, and strains resulting from losing control of the item being lifted. Factors associated with accidents are weight of the item being lifted, awkward postures, inadequate handholds, and the working environment itself. High accident rates were noted when lifting items that ranged from 50 to 600 pounds, particularly in tight working quarters where maneuverability was critical. Research indicated that a mobile lifting arm would eliminate many lifting accidents in environments where other lifting devices (fork lifts, overhead cranes, mobile A-frames) would not be practical. NIOSH has built a first-generation mobile manipulator unit designed to be used on hard, level floors such as in a shop. The complexity of motion, number of moving parts, compact design, and design constraints of the manipulator required advanced computer-aided design work (Figure 3). As a result of the design work, thirty-eight claims are included in the patent applications. NIOSH will be conducting field trails and working with manufacturers to put the manipulator into industrial use.

Dec 1, 2006

By Dennis R. Dolinar, Christopher Mark, Gregory M. Molinda

Despite more than half a century of experience with roof bolting, no design method has received wide acceptance. To begin to improve this situation, National Institute for Occupational Safety and Health (NIOSH) conducted a statistical study of roof bolt performance at a number of mines throughout the U.S. Case histories were collected from 37 mines with a variety of roof bolt types and patterns in a wide range of geologic environments. Performance was measured in terms of the number of roof falls that occurred per10,000 ft of drivage. The study found that roof falls are rare when the roof is strong and the stress is low, even with light roof bolting patterns. The focus of this paper is on the more difficult conditions, where the roof is weaker and/or the stress is higher. Analysis of the results led to guidelines that can be used to make preliminary estimates of the required bolt length, capacity, and pattern. The guidelines are based on the depth of cover (which correlates with stress) and the roof quality (measured by the Coal Mine Roof Rating (CMRR), and the intersection span. Another contribution is a formula for estimating the horizontal stress level in the eastern U.S. coalfields as a function of the depth of cover. The design guidelines are currently being implemented into a computer program called Analysis of Roof Bolt Systems (ARBS).

By Thomas O. Glover

Economic growth in Cameroon was restricted during 1987 owing to a decrease in oil prices during 1986 and the falling value of the U.S. dollar in 1987. The yearly budget reflected a significant drop in revenues and expenditures. Taxes on imports and some exports were increased to raise revenue. The shortage of revenue and the lack of liquidity had restricted the Government's operation and investment programs. External public debt reached an estimated $3.2 billion2 representing 20.8% of the estimated gross domestic product (GDP) of $12.3 billion. The Government operated at an 8.7% deficit in 1987. The GDP growth rate had fallen to 0.6% in 1987 and was projected to remain at that level in 1988. Economic planning was managed through a series of 5-year plans. The country was under the sixth 5-year plan, which would end in 1991. The plan stressed balanced development as one method to achieve the desired results. Sources of revenue for the year included direct and allied taxes (31.2%). customs collections (31.0%), and oil royalties (28.0%). The oil royalties in 1987 represented a larger part of the budget than in 1986. In January 1987, eight African oil exporting countries, including Cameroon, formed the African Petroleum Producers' Association (APPA). The eight countries represented about 80% of the total African oil production of 5.2 million barrels per day in 1987. Cameroon produced approximately 3% of total APPA oil production. Cameroon produced approximately 68.5 million barrels of crude oil in 1987, slightly less than that produced in 1986. Earnings also fell in 1987, not only from falling production, but also from declining oil prices and the fall in value of the U.S. dollar on world markets. Oil had been the main stimulus of Cameroon's growth throughout the past decade, and a key generator of export revenues and financial resources for the economy.

Jan 1, 1989

By Winthrop F. Watts

The U.S. Bureau of Mines evaluated the performance of a catalyzed diesel particulate filter (CDPF) and a CDPF combined with a diesel oxidation catalyst (DOC) at two metal mines. This report describes the results from the two field evaluations. The CDPF-DOC was installed on a load-haul-dump (LHD) powered by a 175-kW, prechambered, turbocharged engine. This system reduced diesel particulate matter (DPM) concentrations by 71±28 pet, as determined by size-selective sampling with gravimetric analysis, and by 71±29 pet, as determined by respirable combustible dust (RCD) analysis at the vehicle operator's location. The CDPF was installed on a diesel-hydraulic, roof-bolting jumbo, powered by a 172-kW engine. The CDPF reduced DPM concentrations by 72±21 pet, as determined by size-selective sampling with gravimetric analysis, and by 62±25 pet, as determined by RCD analysis at the vehicle operator's location. Underground evaluation was more difficult because of frequent movement by the roof-bolting jumbo, variation in daily workload, tremendous fluctuation in ventilation airflow rates, and use of a high sulfur diesel fuel, which promotes the formation of sulfate particles, decreases filtration efficiency, and hastens the deterioration of the catalyst.

Jan 1, 2010

By M. H. Stanczyk

Bench-scale laboratory tests were made by the Bureau of Mines of a segregation-flotation concentrate, assaying 20.43 percent copper, to investigate the influence of various ratios and concentrations of ammonia and carbon dioxide on copper extraction. Leaching the concentrate with a solution containing 900 pounds of ammonia and 360 pounds of carbon dioxide per ton of feed, followed by washing the leach residue with 1.75 tons of a 10-percent solution of ammonium carbonate and about 1 ton of water (as steam) per ton of solids, resulted in a copper recovery of 96.3 percent. Resegregation and flotation tests of the washed residues revealed that 85 percent of the copper in the residue could be recovered. Steam distillation tests of a typical ammoniacal leach liquor, assaying 39 grams copper, 105 grams ammonia, and 77 grams carbon dioxide per liter, recovered over 99 percent of the copper as a mixed oxide-carbonate precipitate. The ammonia losses in leaching, filtering, washing, and distillation were 0.12 pound per pound of copper recovered in the precipitate. Calcination and subsequent hydrogen reduction of the precipitate yielded a metallic copper powder assaying 98 percent Cu, 0.87 percent Si02, 0.10 percent MgO, 0.54 percent CaO, and 0.41 percent R203.

Jan 1, 1961

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for O2, N2, H2, He, and Co2. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4/CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973

By D. A. Elkins

Design plans and detailed cost estimates of mining and treating ore from Maggie Canyon deposit by two alternative methods which can be used in the event of a sudden need to exploit this resource are given . Lower costs are estimated for the operation employing oil - emulsion flotation . The total capital investment required for this operation is estimated at $ 11,750,000 . Assuming an 85 percent recovery in mining , 55.6 pct of the manganese in the ore reserve would report in 153,333 tons of ferromanganese containing 75 pct manganese . The production cost for the 5 - year operation would be about $ 245 per ton of ferromanganese . The total annual operating cost would be approximately $ 7.5 million , distributed , in pct , as follows : Mining 11.9 , milling 24.4 , sintering 9.9 , smelting 47.2 , hauling ore and sinter 2.8 , and general offices 3.8 . Recovery and costs are both higher for the operation employing dithionate leaching . In this operation the required investment is about $ 17,220,000 . Manganese recovery would be 67.6 pct in 186,160 tons of ferromanganese . Production cost would be about $ 284 per ton of ferromanganese . The total annual operating cost would be about $ 10,575,000 , distributed , in pct , as follows : Mining 8.4 , milling 44.4 , sintering 7.4 , smelting 34.7 , hauling ore and sinter 1.3 , and general offices 3.8 . Potential process modifications might reduce the operating cost of the first operation by as much as 7 pct and that of the second operation by as much as 9.5 pct , but exploitation of the deposit by the techniques studied is not economical today .

Jan 1, 1964

By John R. Benham

The Windigo Theilson RARE II area has a low mineral potential. There are no mines or claims in the area. The only observed results of mining activities were five prospect pits near Tolo Mountain. Samples from these pits contained no significant assays. The study area contains more than 190 million cu yds (145 million m3) of cinders in 17 cones. Development of these cinders is unlikely because their locations are remote, and other sources supply area needs. The Geological Survey has classified the area as prospectively valuable for geothermal resources. However, there has been no geothermal exploration activity.

Jan 1, 1982

By J. H. Jansky, P. W. Jeran, G. L. Hassett, M. C. Irani

This Bureau of Mines report tabulates methane emissions from U.S. bituminous coal mines with daily emission rates of at least 100,000 cfd according to States, counties, and coalbeds. Most of the methane emitted is from mines in the Appalachian States. Total daily emissionin 1975 was 216.3 MMcfd, compared with 227.0 MMcfd in 1971 and 214.5 MMcfd in 1973. Thirty counties in nine States had daily methane emissions of 1 MMcfd or more, These emitted 93 percent of the total methane. The highest emissions were from Monongalia County, W. Va,, which accounted for 18.9 percent of the total. This was followed by Marion County, W. Va., 9.6 percent; Buchanan County, Va., 8.5 percent; Jefferson County, Ala., 6.1 percent; and Washington County, Pa., 5.9 percent. The Pittsburgh coalbed emitted 45.7 percent of the total methane, followed by the Pocahontas No. 3 coalbed with 12.9 percent. The report lists 196 mines, of which 60 had daily methane emissions of 1 MMcfd or more. Included in this compilation are the identification and thickness of the coalbed, methane emission, coal production and ventilation rates, number of drifts, shafts, and slopes used for ventilation purposes, shaft depth, age of mine, and gas-to-coal ratio.

Jan 1, 1975

By Jan Zwarcendyk

This study is primarily directed toward providing an understanding of the economic complexities associated with subsidence damage on the surface resulting from underground mining. Some of the pertinent theories on the physical stresses involved are reviewed, and both remedial measures and relevant laws in various countries are discussed. Part I (Chapters 1-3) is an historical overview of various aspects of subsidence problems (theoretical, remedial, and legal) during pre-World War I, between World Wars, and post-World War II, respectively. Part II (Chapters 4-9) presents a comprehensive analysis of the economic aspects of subsidence in relation to the following mining alternatives: (a) carrying out the lowest cost mining method without regard for any surface subsidence, (b) special mining techniques, (c) partial mining, (d) full recovery with stowing, and (e) sterilization or leaving the mineral unmined beneath selected areas. These alternatives are evaluated in terms of their measurable expenses.

Jan 1, 1971

By W. W. Adams

Reports received by the Bureau of Mines, Department of Commerce, from State mine inspectors, for November, 1930, showed that 219 men were killed in the coal mines of the United States during the month, an increase of 25 over the previous month and 33 over November, 1929. On the other hand the production of coal decreased, the output of 43,329,000 tons in November being 8,397,000 tons less than in October and 9,005,000 tone less than in November a year ago. The larger number of fatalities accompanied by a smaller output of coal resulted in a higher death rate4 per million tons in November than in the same month last year or in October, 1930. The November rate was 5.05, as compared with 3.55 for November, 1929 and 3.75 for October, 1930. The increase in the rate for the industry as a whole was chargeable entirely to bituminous mines, as the anthracite mines had fewer fatalities in November than in either of the previous months to which reference has been made. Reports for bituminous mines alone showed that accidents at this class of mines resulted in a death rate of 5.12, based on 195 fatalities and a production of 38,122,000 tons. This rate indicated an increase of 55 per cent over the rate for October, of the same year, and 72 per cent over the rate for November, 1929. The October record was 146 fatalities and 44,150,000 tons, and that for November a year ago was 138 deaths and a production of 46,514,000 tons.

Jan 1, 1930