Search Documents

By John Rusnak, Christopher Mark

Point load testing is used to determine rock strength indexes in geotechnical practice. The point load test apparatus and procedure enables economical testing of core or lump rock samples in either a field or laboratory setting. In order to estimate uniaxial compressive strength, index-to-strength conversion factors are used. These factors have been proposed by various researchers and are dependent upon rock type. This study involved the extensive load frame and point load testing of coal measure rocks in six states. More than 10,000individual test results, from 908 distinct rock units, were used in the study. Rock lithologies were classified into general categories and conversion factors were determined for each category. This allows for intact rock strength data to be made available through point load testing for numerical geotechnical analysis and empirical rock mass classification systems such as the Coal Mine Roof Rating (CMRR).

By W. T. Benson

The Bureau of Mines has examined selected deposits of titanium minerals throughout the United States. The titaniferous magnetite deposits in the western San Gabriel Mountains, Los Angeles County, Calif., were among those selected for study, and in 1956-58 field work was conducted to determine the extent and character of the titaniferous magnetite deposits occurring in the area. This report describes this work and summarizes earlier work in the area by the Bureau and others. The titaniferous magnetite occurs disseminated as seams and lenticular pods in an anorthosite belt 4 to 6 miles wide that trends about. N. 80° W., extending from sec. 13, T. 3 N., R. 12 W., to the west boundary of R. 14 W., at which point the titaniferous magnetite-bearing rocks disappear beneath the sediments in the Santa Clara River Valley.

Jan 1, 1962

By A. C. Johnson

The T. L. shaft of the Eureka Corp., Ltd., near Adams Hill, Eureka, Nev., was sunk in 1954 and 1955 to permit exploration and development of the lead-zinc-silver ore that had been indicated by drilling. This paper describes the sinking of the 4-compartment, vertical shaft to a depth of 1,127 feet and includes pertinent details of equipment, methods, and costs. A shaft crew of 10 men, supplemented by 13 hoistmen, topmen, carpenter, and shop crewmen, sank and timbered the 1,127 feet of shaft in 630 workdays. Total labor per foot of shaft was 107.95 man-hours. Supplies per foot of shaft included 20 pounds of explosives, 1.61 pounds of drill steel, and 200 board-feet of timber. Power consumption, including that required for pumping, averaged 3,726 kw.-hr. per foot.

Jan 1, 1958

By E. C. Westman

Three-dimensional velocity tomograms were generated on a daily basis to image mining-induced changes to the overburden above a longwall mine. The hypothesis was that a coherent redistribution of seismic velocity, due to the development of high-stress zones, could be imaged at the mine scale. Seam depth was 360 m and source location depth varied from 100 to 1000 m. Sixteen geophones were distributed over a 600 by 600 m square area on the surface above the mine. More than 12,500 events were recorded over an 18 day period. The recorded seismicity provided input for the local-earthquake tomography code, SIMULPS. Eighteen tomograms were generated and high-velocity regions correlated well with high abutment stresses. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated. These results indicate that velocity tomography can be used to provide a better understanding of temporal changes within a rock mass, and can potentially be used to produce a better understanding of the mechanisms that lead to unanticipated ground failures.

Jan 1, 2008

By E. C. Westman

Three-dimensional velocity tomograms were generated on a daily basis to image mining-induced changes to the overburden above a longwall mine. The hypothesis was that a coherent redistribution of seismic velocity, due to the development of high-stress zones, could be imaged at the mine scale. Seam depth was 360 m and source location depth varied from 100 to 1000 m. Sixteen geophones were distributed over a 600 by 600 m square area on the surface above the mine. More than 12,500 events were recorded over an 18 day period. The recorded seismicity provided input for the local-earthquake tomography code, SIMULPS. Eighteen tomograms were generated and high-velocity regions correlated well with high abutment stresses. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated. These results indicate that velocity tomography can be used to provide a better understanding of temporal changes within a rock mass, and can potentially be used to produce a better understanding of the mechanisms that lead to unanticipated ground failures.

Jan 1, 2008

By Albert L. Brautigam, Michael R. Yenchek, Jeffrey Shawn Peterson, James C. Cawley

The National Institute for Occupational Safety and Health investigated how the starting of induction motors may cause nuisance tripping of short-circuit protection on coal mine power systems. This research had a dual purpose: 1) to identify how motor-start waveforms differ from those for short circuits and 2) to devise a method to provide short-circuit protection without intentional time delays to account for motor starts. This technology will help ensure that surface temperatures of energized electrical apparatus will not exceed gas or dust ignition thresholds when short circuits occur.

By Stephen C. Tadolini, Thomas M. Barczak, Paul McKelvey

A new generation of hydraulic mine support prestressing devices has been developed. These thin-walled steel shells are machine-welded and can be inflated with water or any liquid to provide prestressing for a wide variety of roof support products ranging from Can supports to props and cable bolts. With an expansion capability of several inches, depending on the geometry and size of the unit, they can also establish roof contact eliminating the need for wooden wedges or crib blocks that are commonly employed with several standing roof support products. Capable of withstanding pressures from 1,000 to 6,000 psi, these cells are able to transfer roof loading into the support structure without rupturing. A recent development has been the addition of an inexpensive yield valve that provides control of the maximum pressure and load development on the support. This paper examines the performance capabilities of these inflatable prestressing units and the impact they have on the performance of various support systems, including an evaluation of the overall stiffness of the support system and the load control during yielding of the prestressing unit. Recommendations are made regarding the design requirements of the prestressing unit to optimize the support performance. A summary of mine applications using this technology is provided with general comments regarding their impact on ground control.

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

By Mark Davis

As a follow-on to previous investigations, reduced treatment levels for the optimum fire retardant/preservative system were evaluated. An impregnation of 3.5 lbs/ft3 of Fyreprufe followed by 3.5 mils of Albi 107A plus an Albi 144 top coat provides adequate flammability and flame spread protection. However, there is a significant loss in compressive strength at this retention level, particularly parallel to the grain. A pilot-size pressure impregnation cell was installed for use in treating larger quantities of wood. Based on the optimum fire retardant/preservative treatment system - Fyreprufe/ACC impregnation followed by Albi 107A/144 intumescent paint - a model treatment pro¬cess was developed, capable of handling 3 million board feet per year. Associated annualized costs per thousand board feet (K bd. ft.) for treating 12" x 12" timber were calculated to be: Impregnation: $-63.00/K bd. ft. Coating: $112.00/K bd. ft. A literature search was conducted to identify materials and techniques suitable for a localized stench warning system for heated mine timbers. Based on this review, a number of stench warning concepts were developed. Those based on surface coating were given a preliminary laboratory evaluation.

Jan 1, 1982

By L. C. IlsLey

The increasing use of Diesel engines for operating equipment on trunk-line railroads and for power-plant units has stimulated interest in the use of Diesel engines for other lines of work, among which is the possibility of substituting Diesel locomotives for trolley locomotives for mines. The possibility of developing Diesel locomotives for duty in American mines is not as remote as it might seem, particularly in view of the fact that locomotives of this type are already used in considerable numbers in European mines. A study of Diesel locomotives in Europe is contained in Report of Investigations 3320, Diesel Mine Locomotives - Development and Use in European Coal Mines, by George S. Rice and F. E. Harris.

Jan 1, 1938

By Fredrick L. Johnson

No mineral resources were identified during the investigation of the White Cloud-Boulder RARE II area. Only a few claims have been located in the area and only two workings were found. However, there has been considerable exploration and mining activity near the RARE II area. Sand and gravel resources are abundant but similar deposits occur closer to market areas. There are no known coal, oil, or gas deposits. Most of the RARE II area is underlain by volcanic rocks. The likeliest host rocks for metallic minerals are the metasedimentary rocks exposed in the south part of the area; there is potential for zinc and silver resources at a prospect in that part. Traces of scheelite and powellite were observed in the Kent Peak-Ryan Peak area along hair-line fractures in calcareous country rock. While no significant concentrations of the minerals were found, their presence, a northwest alignment of prospects with similar deposits, and an abundance of dikes near the deposits, suggest that the intrusive system (Summit Creek stock) exposed near the head of Little Fall Creek may extend to the northwest under the RARE II area.

Jan 1, 1983

Tennessee is the largest federal program state in the nation, with 62 active surface and underground coal mines. Tennessee's coal resources lie in 22 coal seams in 22 counties. Twelve seams are being mined at this time. Mining in the northern counties is primarily in steep slope areas in the Cumberland Mountains. The relatively flat terrain associated with the Cumberland Plateau makes area-rnining the most common production method in Tennessee's southern counties. The State of Tennessee gained primacy August 10,1982, when its regulatory program was conditionally approved, subject to the correction of certain deficiencies. On May 16,1984, the Tennessee General Assembly repealed most of the Tennessee Coal Surface Mining Law of 1980, effective October 1, 1984. With this action, withdrawal of the state regulatory program was formalized, and on October 1,1984, the Office of Surface Mining's Knoxville Field Office became the regulatory authority. Tennessee is not eligible to receive funds for an abandoned mine reclamation program because it does not have an approved regulatory program. Accordingly, the Tennessee Abandoned Mine Lands Program does not receive federal AML grants. Since 1984, AML projects have been completed under cooperative agreements between OSM and the state; emergency projects are completed by the Office of Surface Mining.

Jan 1, 1992

Now more than ever, the United States must have an adequate and dependable supply of minerals to meet its defense and economic needs. A chief mission of the U.S. Department of the Interior Bureau of Mines is to help ensure that the United States meets these needs at acceptable environmental, energy, and economic costs. As it looks toward the 21st century, the Bureau of Mines will focus its attention on the following areas: - upgrading the capabilities of its mineral information and analysis program - expanding mineral land assessment activities - disseminating the practical results of federally funded research activities to the private sector through enhanced technology transfer - addressing the impact of regulations on mineral industries - addressing the needs for mineral-oriented training and research in the Nation's universities - enhancing mine worker health and safety - improving mining and mineral processing productivity through automation, robotics and other innovative technologies - reducing the environmental impact of mining and mineral processing operations - and enhancing the accessibility and conservation of domestic mineral resources.

Jan 1, 1991

By H. John Head, Fred N. Kissell

In This Chapter [Gas reports from around the world Regulations for gassy mines in the United States Differences between metal/nonmetal mines and coal mines Monitoring for methane and taking action Diluting methane with additional ventilation Eliminating ignition sources What experienced mine operators say about methane control and Looking for methane when starting a new mine or expanding an existing mine] This chapter gives guidelines for preventing methane gas explosions during metal and nonmetal mine development and subsequent production operations.3 Emphasis is placed on recognizing the differences between coal mines, where the potential for methane hazards is relatively well understood, and metal/nonmetal mines, where methane may accumulate unexpectedly. Also, interviews with experienced mine operators add much to a complete understanding of what must be done to address methane problems in metal/nonmetal mines. METHANE GAS IN METAL/NONMETAL MINES Gas reports from around the world. The presence of methane gas in metal/nonmetal mines around the world is more common than one might imagine [Edwards and Durucan 1991]. For example: • The former Soviet republics have occurrences of methane and hydrogen in apatite, gold, and diamond ores, where solid or liquid bitumen occurs in the rock. • Scandinavian iron ore deposits include methane and other hydrocarbons in boreholes that intersect pitch and asphalt within the deposits, and methane and nitrogen in boreholes and fissures in arsenic and sulfide ores.

Jan 6, 2006

By Forrest T. Moyer

The safety record of the metal mining and milling industries in 1965 is reviewed by the Bureau of Mines. The overall injury-frequency rate of 23.77 per million man-hours was 5 percent lower than in 1964 and was the lowest annual rate in a statistical history beginning with 1931. The injury-severity rate of 3,521 days lost per million man-hours in 1965 represented a 5-percent improvement over 1964. However, the total of 3,825 disabling work injuries comprised 61 fatal and 3,764 nonfatal injuries, one and 92 more, respectively, than in 1964. At primary nonferrous smelters, refineries, and reduction plants, the injury-frequency rate of 8.97 per million man-hours in 1965 was 13 percent lower, but the severity rate percent higher than in 1964. these plants in 1965, 4 more of 1,173 days lost per million man-hours was 17 There were 12 fatal and 971 nonfatal injuries at and 28 fewer, respectively, than in 1964.

Jan 1, 1969

By Franklin H. Persse

Domestic bismuth supply was projected from production figures for the ores in which it occurs--copper, lead, zinc, and tungsten. Published and unpublished data concerning host ores were examined to determine bismuth reserves and resources, and mine production. Potential recoverable bismuth occurring with reserves and resources of copper, lead, and zinc was estimated to be 36.3 million pounds. A bismuth availability diagram was developed from quantity estimates and ratios of production cost to value for these host ores. Additional recoverable bismuth occurring with domestic tungsten reserves was estimated to be 1.5 million pounds. Domestic byproduct production of bismuth will approximate 1.3 million pounds annually by 1980. This quantity will provide about 37 percent of the 3.5-million-pound estimated requirement for that year. Known world supply of bismuth appears to be sufficient for world demand to the end of this century. The study indicates that bismuth reserves and potential resources in the rest of the world have not been adequately reported.

Jan 1, 1970

By Gerald T. Homce, James C. Cawley

Problem: CFOI and SOII data show that 2,287 U.S. workers died and 32,807 workers sustained days away from work due to electrical shock or electrical burn injuries between 1992 and 1998. Method: The narrative, work activity, job title, source of injury, location, and industry for each fatal electrical accident were examined. A primary causal factor was identified for each fatality. Results: Electrical fatalities were categorized into five major groups. Overall, 44% of electrical fatalities occurred in the construction industry. Contact with overhead power lines caused 41 % of all electrical fatalities. Discussion: Electrical shock caused 99% of fatal and 62% of nonfatal electrical accidents. Comprising about 7% of the U.S. workforce, construction workers sustain 44% of electrical fatalities. Power line contact by mobile equipment occurs in many industries and should be the subject of focused research. Other problem areas are identified and opportunities for research are proposed. Impact on Industry: Improvements in electrical safety in one industry often have application in other industries.

By Frank E. Cash

As a part of its safety program the United States Bureau of Mines has fostered the development, use, and improvement of portable electric mine lamps. Although there is still need for better illumination in mines and the replacement of open lights has been slow, improvement in electric cap lamps and increase in their use indicate one phase of recent progress toward safer and more efficient mining This report is the result of a recent survey of electric-lamp installations in the Alabama mining; district; it shows the misuse, increase in use, and relation to certain classes of accidents of these installations.

Jan 1, 1935

By Neil J. Mansfield

Tool manufacturers are required to provide declarations of vibration emission values in order to sell their tools within Europe. To ensure that users can compare results obtained from different manufacturers, the declared values must be obtained using a methodology as specified in the relevant test code (such as in the ISO 8662 series of standards). In most cases, the vibration emission values obtained using test codes under-estimate the vibration that an operator will be exposed to when using the tool on a work-site. A further problem with manufacturers’ data is that usually only a single value is provided for a tool. This is despite many factors affecting the vibration emission, including inserted tool type, work piece, operator technique, tool condition. New improved test codes are in the process of being developed. In order to provide guidance to users on how to interpret manufacturers’ data, a Draft CEN Technical Report (Draft CEN/TR 15350 (2005)) was developed. Part of the CEN/TR provides multiplication factors for combinations of task and tool type. For example, data obtained from electrical hammer drills (tested according to EN 60745-2-6:2003) should be multiplied by 2, for hammering applications, in order to obtain an estimate of the vibration emission during work. In response to concerns from industry, the UK trade association OPERC have, in collaboration with hire companies and tool manufacturers, established a freely accessible online database of tool emission values based on independent tests carried out under simulated work-site conditions. This paper reports some of the data obtained from electrical hammer drills, highlighting the range of emission values that can be obtained for a tool. Data from many other tool types are also included in the database. Methods Tri-axial hand-arm vibration was measured at both handles of each of 19 electrical hammer drills, in accordance with ISO 5349-1 (2001). Each tool was measured with three experienced operators and at least 5 runs were completed for each operator. Tools were tested using a range of appropriate new bits from 4 to 40 mm diameter. The minimum number of bits for a tool was 3; the maximum number was 29. 146 tool / bit combinations are reported here, representing about 2200 individual 6-axis measurements. Operators were required to drill vertically into a concrete block with a compressive strength after 28 days of 40 N/mm². Two drills (1 and 15) were battery powered; others were powered using a 110V transformer supply.

Jan 6, 2006

By Joan Weinberg

Real gross national produce (GNP) grew at a seasonally adjusted annual rate of 2.0% in the fourth quarter (table 1). The restrained quarterly growth rate was the slowest in 2 years, and was substantially slower than the 2.5 % rate of the previous quarter. According to the U.S. Department of Commerce, the summer drought reduced the fourth-quarter growth rate by 1.1 percentage points. A growing trade deficit and a reduction in business investment were the key economic factors curtailing growth. The trade deficit widened by $6.8 billion, reflecting both a surge of imports and a slowing of exports. Business investment declined 3.7%, mainly as a result of a slowdown in computer sales. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 3.8% for 1988, the fastest in 4 years, despite the drought. However, on a fourth-quarter-to-fourth-quarter basis, real growth measured 2.7%. Increased exports and business spending for plant and equipment accounted for much of the 1988 GNP growth. Employment continued to grow as the manufacturing sector added 414,000 new workers (table 2). Of these, the primary metals industry added 26,000 workers, and the clay, glass, and stone industry added 10,000. The civilian unemployment rate remained low throughout 1988, fluctuating between 5.3% and 5.4% during the last quarter.

Jan 1, 1989