Search Documents

By J. V. Batty

Radioisotopes of selenium (se78) and tellurium (Te123) were successfully employed by the Bureau of Mines as tracers in metallurgical research directed to developing improved methods for volatilizing these elements from low-tenor raw materials. Prior research, guided and controlled by conventional analytical methods, was seriously hampered by inconsistent selenium and tellurium analyses, by the slowness of the conventional chemical methods, and by the poor accountability of these volatile elements in test products. Methods were devised and evaluated for admixing the radioactive tracer with typical raw materials and then following the deportment of the selenium and tellurium by radiometric methods with occasional chemical analysis checks. These techniques were found unusually effective in (1) quantifying the completeness and the rate of volatilization of selenium and tellurium while heating the raw materials at different rates to different temperatures and (2) accurately tracing and quantifying the distribution of minute amounts of these volatile elements in the several products made by high-temperature treatment and in the several units comprising the experimental equipment.

Jan 1, 1962

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

By G. F. Friel, J. C. Edwards

A series of seven underground-coal-mine fire experiments was conducted in the Safety Re-search Coal Mine at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory. Coal and styrene-butadiene-rubber conveyor belting were burned upwind of two sensor stations, 18 m and 148 m from the fire source. Exhaust from a diesel locomotive flowed over the fire sources in six of the tests. Metal-oxide-semiconductor (MOS), CO, and optical-path-smoke sensors were positioned at both stations and found to be an optimum set of sensors for the fire discriminations. A representative set of 7,679 samples of CO data and data from the smoke and diesel-exhaust MOS sensors were used as inputs to train a neural network (NN). By testing 42,538 data samples from the seven experiments, all fires were detected by the NN within 9.67 min from the onset of significant changes in the MOS voltages without any false alarms.

As mining operations in the United States (US) have become more productive, controlling the dust exposure of mine workers has become more challenging. In response, US mining operations are applying basic controls at elevated levels and are looking to emerging control tech­nologies in an effort to better control airborne respirable dust levels. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducts research to develop and/or improve control technologies that reduce the respirable dust exposure of workers in underground coal mines. The goals of this research involve optimizing the use of water sprays and ventilating air, as well as, evaluating emerging control tech­nologies. An overview of dust controls typically utilized in underground US coal mines will be provided. An update on ongoing PRL research efforts that are evaluating new control technologies will also be presented.

Jan 1, 2008

By G. T. Lineberry, W. J. Wiehagen

A Paradigm Shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results invokes questions such as: How much was produced? At what cost? And, was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as preeminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured, and formed new coalitions. Investments in new technology and concentration on productivity have been part and parcel with these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. These changes in mining present an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now might offer some interesting opportunities for the future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work force. The WCPM work Crew Performance Model, see pp. ) is one approach to defining, capturing, and transferring this expertise.

By R. V. Ramani

"In this paper, the current status of respirable dust control in coal mine atmospheres is presented. The advancements in the engineering control of dust generation and entrainment, and of reducing the exposures are summarized. The results of the Health Surveillance Program are briefly reviewed. The results of research conducted in the Generic Mineral Technology Center for Respirable Dust are presented. The 1995 NIOSH criteria document on respirable coal mine dust is briefly reviewed. The fundamental scientific and engineering issues in need of research are discussed. A detailed bibliography is attached.IntroductionFor coal mines in the United States, the current permissible exposure limit (PEL) of 2mg/m3MRE-equivalent concentration (an 8-hour TWA concentration measured gravimetrically) was established by Public Law 91-173: the Federal Coal Mine Health and Safety of 1969 (the 1969 Coal Act). This standard is reduced when the respirable quartz content in the dust sample exceeds 5%; the reduced standard in mglm3 is obtained by dividing 10 by the percent quartz. The OSHA and ACGIB PEL for respirable coal mine dust is also 2 mg/m3 , and OSHA PEL for respirable quartz is 100 µg/m3 . The 1969 Coal Act also prescribed two activities in the Coal Mine Respirable Dust Sampling Program and the National Coal Workers' Health Surveillance Program n to control respirable dust in mines, and the coal worker's pneumoconiosis (CWP) among the coal miners.There are three principal methods by which personal exposures to respirable dust are controlled. The first is engineering control where the aim is to reduce the concentration in the mine atmosphere to or below the mandated level. The second is the provision of personal protective devices which allow the miner to work in dusty atmospheres without increasing personal exposure. The third is the use of administrative controls where the miner's exposure is controlled through work schedules and procedures to keep miner exposure at or under the mandated levels. The 1969 Coal Act specifically prohibits the use of respirators in lieu of environmental control. The compliance sampling program essentially does not give any credit to the use of administrative controls."

Jan 1, 1998

By T. A. Sullivan

Refining in a molten salt electrolyte was investigated as a means of recovering nickel containing less than 1 percent and preferably less than 0.2 percent cobalt from nickel products containing up to 5 percent cobalt. Electrolytic separation of nick and cobalt was accomplished in a molten KCl-LiCl-NiCl2 electrolyte. Nickel containing less than 0.10 percent cobalt was routinely prepared. Factors that influenced the transfer of cobalt to the refined product were the nickel concentration of the electrolyte, the cobalt concentration of the electrolyte, the ratio of nickel to cobalt in the electrolyte, and cathode current densities. A method of recovering the cobalt from the electrolyte was developed. The possibility of preparing high-purity nickel by this process was shown, as well as the preparation of various cobalt-nickel-tungsten alloys.

Jan 1, 1968

By Gerrit V. R. Goodman

In This Chapter [Design and operation of machine-mounted scrubbers Dust control with scrubbers and blowing ventilation Dust control with scrubbers and exhaust ventilation Dust control with exhaust ventilation and no scrubber Dust control methods common to all continuous miner sections Dust control for roof bolters] This chapter explains how to control dust at continuous miner sections in coal mines where the main dust sources are continuous miners and roof bolters. In relation to dust, there are three categories of continuous miner faces depending on the type of ventilation and whether or not a machine-mounted dust scrubber is used. These are— 1. Mining machines with dust scrubbers used with blowing face ventilation 2. Mining machines with dust scrubbers used with exhaust face ventilation 3. Mining machines without scrubbers used with exhaust face ventilation The approach to dust control is somewhat different in all three of these. However, there are many dust control features (such as the need to provide adequate airflow) common to all continuous miner sections. For workers at roof bolter faces, there are two dust sources: 1. Dust from the continuous miner when it is upwind. 2. A malfunctioning dust collector on the bolter, which allows dust to escape DESIGN AND OPERATION OF MACHINE-MOUNTED SCRUBBERS [Almost all new continuous miners are equipped with scrubbers. When the dust is excessive, it is possible that the scrubber needs some maintenance.]

Jan 6, 2003

By Roy C. Bartholomae, Jeffrey Shawn Peterson

1. INTRODUCTION In the early 1980s, the U.S. Department of the Interior’s Bureau of Mines Pittsburgh Research Center required that a large reverberation acoustic facility be constructed. This facility was designed to determine the sound power level emissions of mining equipment, especially continuous miners and jumbo drills. A contract for a conceptual design of a reverberation chamber was awarded to Wyle Laboratories of Huntsville, AL, which had extensive experience in the design, construction, and accreditation of acoustical reverberation chambers. The following standards were referenced as guidelines for the design of the chamber: ANSI S1.31-1980, “Precision Methods for the Determination of Sound Power Levels of Broadband Noise Sources in Reverberation Rooms” and ANSI S1.32-1980: “Precision Methods for the Determination of Sound Power Levels of Discrete-Frequency and Narrowband Noise Sources in Reverberation Rooms.” Specific requested criteria included that the room be large enough to accommodate typically large mining equipment and that there be adequate acoustical modal density in the frequency range of interest. It was also required that the room dimensions would support broadband acoustical measurements down to the 100 Hz third octave band. With the closing of the Bureau of Mines in 1996, this reverberation chamber lay dormant for a number of years. However, this facility is now part of the National Institute for Occupational Safety and Health’s (NIOSH’s) Pittsburgh Research Laboratory (PRL). One of NIOSH’s missions is to decrease noise induced hearing loss among the nation’s mineworkers. To this end, PRL researchers are refurbishing and instrumenting this reverberation chamber to facilitate assessment of the various engineering controls being developed to decrease the sound power level emissions of mining equipment. Early on, this work has sought to bring the chamber up to the level of ISO 3743-21 standard for engineering grade measurements for broad-band noise, with a longer range goal of improving the lab to meet the requirements of ISO 37412standard for broadband precision grade measurements. 2. DESIGN OF THE REVERBERATION CHAMBER The nominal room dimensions are 18.3 meters long by 10.3 meters wide with a height of 6.7 meters. The chamber volume is 1,286 cubic meters. These dimensions are important, as few reverberation facilities are large enough to test typically huge mining equipment. The floor is poured concrete with a sealer to make it acoustically reflective. The walls are built of hollow concrete block, 16 inches long x 8 inches high by 12inches thick. Each block has two hollow cores. The hollow block cores were completely filled with concrete with horizontal and vertical steel reinforcing bars 16 inches on center. This was done to supply a

By E. G. King

As low-temperature heat-capacity and entropy data were available for only one sesquisulfide (cerium sesquisulfide), it appeared desirable to augment the information for this class of compounds by measuring the sulfides of antimony and indium. In addition a pressing need existed for data on indium sulfide to supplement vaporization studies in progress in the Department of Mineral Technology, University of California. This Bureau of Mines paper reports low-temperature heat-capacity measurements and entropy evaluations at 298.15° R. of antimony sesquisulfide of stoiehiometric composition (Sb2S3) and of indium sesquisulfide which was somewhat deficient in sulfur (In2S2.93). The data for the latter substance were adjusted to correspond to the stoichiome tric composition (In2S3 ) . Indium sesquisulfide has a lower entropy at 298.15' K, than either antimony sesquisulfide or cerium sesquisulfide, in line with the higher atomic density of the indium compound.

Jan 1, 1962

By H. R. Babitzke

The purpose of this investigation was to develop an alloy of columbium for use at high temperatures and for nuclear applications. The properties of possible alloys were determined, and the more promising ones were selected for further improvement. Criteria for selection were machinability, hardness, workability, tensile strength, and oxidation resistance. Thirteen 100-gram ingots, ranging from 100 percent columbium to 100 percent vanadium, were prepared and subjected to various tests. Also included for comparison were zirconium and the zirconium alloy, zircaloy-2. Test results showed that a columbium alloy, containing 10 atomic percent vanadium merits further development. Besides being workable at room temperature, the columbium-10 atomic percent vanadium alloy has oxidation resistance superior to the other alloys of the series and is also superior to zirconium or zircaloy-2. The latter two materials have comparable neutron-absorption cross sections. The strength and hardness values of the alloys tested were found to increase with increasing vanadium content, reaching a maximum at 50 atomic percent vanadium and decreasing with further increase in vanadium. This behavior is typical of binary alloys wherein each element will retain any proportion of the other in solid solution. INTRODUCTION There is an increasing need for alloys for service at high temperatures. Since current world reserves of columbium metal approximate 1,500,000 tons (1),4 this metal is now readily available. Columbium can ties; be considered a practical base material for high-temperature alloys required in nuclear reactors and in aircraft and space vehicles. General requirements chosen are: (1) Workability, (2) satisfactory mechanical properties at temperatures approaching 1,000° C., and (3) resistance to oxidation at such temperatures.

Jan 1, 1962

By Leonard J. Prosser, Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

By D. F. Smith

The thermodynamic data presented in the literature for zirconium compounds are incomplete. Among the compounds for which adequate data are Zacking are zirconium fluoride and sulfate. This paper reports experimental heat-content values determined by the Bureau of Mines for these two zirconium salts throughout the temperature range of 273° to 1,200° K. No crystalline transformations were found in the two compounds investigated, and neither of the compounds melted over the temperature range studied. MATERIALS TESTED The Oak Ridge National Laboratories, Oak Ridge, Tenn., supplied the two zirconium salts used in this investigation. The zirconium fluoride was high- purity reactor grade material. The zirconium sulfate contained between 0.01 and 0.10 percent hafnium and calcium, and other elements in concentrations below 0.01 percent, A spectrographic analysis of the two compounds is given in table 1. Before use the compounds were dried at 400° C. for several hours to removed adsorbed moisture.

Jan 1, 1962

By Jeff Kravitz, John Kovac, Wayne Duerr

Since 198 1, Federal mining law has required every miner working in underground coal mines to have a self-contained, self-rescuer (SCSR) available for use in emergencies. Some miners that have escaped from fires using SCSR's have reported that they had to remove their mouthpiece to talk during escape, thus compromising the protection afforded by the SCSR. If miners are in thick smoke during an escape, they may have trouble if they become separated from their group. The visibility can be so poor that separation can occur at very short distances. To address this problem, two-way, FM radios were built into the SCSR to improve the ability to communicate should the miners be separated over relatively short distances. The SCSR prototypes built and used in testing included both two-way radios and improved mouthpieces. Comparison studies were conducted using combinations of the new and old mouthpieces, and trials using the radio or not using the radio. Subjective judgments indicate that communication ability was significantly improved using the prototype devices. Communication problems have been encountered with teams using standard voice- powered communications systems. Mine rescue teams perform rescue and recovery work under extremely hazardous conditions, life lines are a standard part of mine rescue team equipment. Leaky feeder and quasi-leaky feeder life line communications systems provide significant improvements over standard systems. These improved systems allow all members of the team to communicate with each other and their base of operations. These innovations will significantly enhance the safety of mine rescue operations.

To improve the ventilation of large-opening under-ground stone mines by using stoppings made from stone left in place. Background Underground stone mines typically use large room-and-pillar openings with little ventilation control. Stone miners may be exposed to contaminants that include silica dust, diesel particulate matter (DPM), exhaust gases, nuisance dust, and face shot (blasting) fume gases. The health risks from breathing these fine particles and toxic organic materials are well documented. Although contaminants such as dust or diesel exhaust can be some-what controlled at the source, the escaping contaminants are often diluted and removed from work areas using ventilation with minimal controls. In many cases, current mine ventilation practices use trial-and-error techniques to improve ventilation. The growing realization of the importance of a healthy work environment along with increased regulations will require many stone mines to implement new ways to improve ventilation. In-place stone stoppings are one option. Mine air flows from one point to another because of a pressure differential between those points. This pressure differential is established using a mechanical fan in conjunction with separations (stoppings) between high-pressure (intake) and low-pressure (return) airways. The separation of intakes and returns is an important concept that is used in most other types of mines. Normally, air moves through underground stone mines with minimal control technology. Fans are placed in locations where they are thought to be most beneficial, and intakes are not separated from returns. In a few smaller underground stone mines, proper ventilation can be achieved with a few strategically placed fans. However, as these mines increase in size, moving adequate quantities of air through-out the mine becomes harder, and separation of intakes and returns becomes a problem. Building traditional mine stoppings to separate the intake and return airways in entries with a cross-section area often exceeding 800 ft2 is difficult. The stoppings must be able to withstand both the dynamic pressure from face shots and the static pressures created by the fans. Construction and maintenance difficulties, as well as high costs, are the main factors preventing these traditional mine stoppings from gaining wide acceptance by the stone mining industry.

Dec 1, 2002

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

By Forrest T. Moyer

INJURY experience and employment data are presented in this (chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron-blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume III. The 1963 figures are preliminary and are subject to revision. METAL MINES Preliminary estimates for the metal-mining industry of a combined fatal and nonfatal injury-frequency rate of 32.34 per million man-hours in 1963 indicate only a slight change from the rate of 32.00 in 1962. Metal operations had 41 fatal and 3,110 nonfatal injuries during 1963.

Jan 1, 1964

1. A total of 14,413 mining operations reported employment to the Mine Safety and Health Administration (MSHA). Nearly half (48.9%) were sand and gravel operations, followed by stone (28.5%), coal (14.7%), nonmetal (5.7%), and metal mines (2.1%). 2. Mine operators reported 240,000 full-time equivalent workers1 (down 3.9% from 1999). Independent contractors reported 42,000 full-time equivalent workers working on mine property (up 8.6% from 1999). Coal operators accounted for 26.8% of reported employee hours, followed by stone operators (25.9%) and sand and gravel operators (12.1%). 3. Eighty-four (84) work-related mine fatalities occurred in 2000 compared to 90 the year before. •The mine fatality rate was 29.8 per 100,000 full-time equivalent workers compared to a fatality rate of4.6 per 100,000 employees for all private industry. •Thirty-one percent (31%) of the fatalities occurred in underground work areas, which account for only17% of total employment. •Although the largest number of fatalities (28) occurred among miners who work for coal operators, coal contractor employees had the highest fatality rate (61.1 per 100,000 full-time equivalent workers). 4.There were 10,839 nonfatal lost-time injuries reported to MSHA, occurring at a rate of 3.8 injuries per 100full-time equivalent workers, and resulting in a total of 417,918 lost workdays.2 •Among all employees,3 the highest injury rate occurred among coal operator employees (5.6 nonfatal injuries per 100 full-time equivalent workers). •The highest percentage (34.7%) of nonfatal lost-time injuries were due to handling materials (e.g., over-exertion in lifting, pulling, or pushing objects), which also accounted for the greatest percentage of lost workdays (29.3%). •Among the most frequently occurring injuries, the most severe (as measured by the median number of days lost) were associated with accidents involving falls of ground, the use of powered haulage, and slips or falls. •The most frequently reported part of the body injured was the back (22.9% of all injuries). Back injuries accounted for the highest percentage of lost workdays (21.6%). 5.Seven hundred sixty-seven (767) cases of occupational illness were reported to MSHA. •The most frequently reported illness was repetitive trauma, resulting in joint, tendon, or muscle inflammation or irritation (37.3%). •There were 155 (20.2%) illnesses reported as hearing loss. The majority (68.4%) of hearing loss cases occurred among surface workers. •Coal workers' pneumoconiosis accounted for 14.5% of reported illnesses.

May 15, 2002