Search Documents

By N. E. Hanna

The current list of permissible explosives includes 124 different brands. Fifteen of these are gelatinous, and the rest are the more commonly used granular ammonium nitrate type. Their rates of detonation range from 1,300 to 5,600 meters per second, and the weights of 1-1/4 x 8-inch cartridges range from 86 to 244 grams. The list of permissible blasting devices includes 1 Cobra, 2 Hydrox, and 9 Cardox models. All of these devices are based on discharge of high-pressure gas from a pressurized shell in a shothole. INTRODUCTION To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain schedule tests prescribed by the Bureau of Mines. The explosives listed here were tested under Schedule 1-G,3 which has since been replaced by Schedule 1-H;4 the blasting devices were tested under Schedule 26A.5

Jan 1, 1962

By John E. Trombly

System objectives and design criteria for an in-mine ULF radio paging system are discussed Coding formats, frequency and bandwidth selection criteria leading to the system design are discussed. The prototype call alert transmitter and pocket page receiver is functionally described. The report includes circuit descriptions, schematics, parts lists, printed circuit fabrication and assembly drawings. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 2011

By N. S. Dalal, X. Shi

"SUMMARYElectron spin resonance (ESR) measurements provide direct evidence for the involvement of the glutathionyl radical, as well as an isolable Cr(V)-glutathione intermediate in the Cr(VI) glutathione redox reactions. These results indicate a new mechanism for the reduction of Cr(VI) by glutathione in relationship to cellular environment and suggest that synergistic reactions of Cr(V) and GS· might be responsible for the (unexpected) increase in the Cr(VI)-induced DNA-strand breaks at high glutathione levels.INTRODUCTIONWhile the reduction of Cr(VI) by glutathione (GSH) is thought to be a critical' step in the pathogenesis of the Cr(VI)-exposure related carcinogenesis1- 4, the exact reduction mechanism is not yet understood. The following reaction steps have been suggested :(A) Initial step:Cr04 2- + GSH - GSCrOa - (1)(B) At high GSH levels:GSCroa- + GSH - Cr( IV) + GSSG (2)(C) At low GSH levels: GSC rO a - - Cr ( V ) + GS ·(3)Thus far, however, in these reactions, the GS· radical has eluded spectroscopic detection, while the evidence for the Cr(V) formation has been reported positives as well as negative2·. Her~ we present spin-trap ESR evidence for the formation of the GS· radical, and a definitive ESR detection of an isolable cr(V)-GSH intermediate in Cr(VI)-GSH reactions.MATERIALS. AND METHODSESR spectra were obtained at X-band (-9.7 GHz) using a Bruker ER200D ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR Gaussmeter (Bruker, Model ER035M) and the microwave frequency was measured with a Hewlett-Packard (Model 5340A) frequency counter. The spin probes, a-(4-pyridyl-1-oxide) -N -tert-butylnitrone (4-POBN) and 5,5-dimethyl~1-pyrroline-1-ox1de (DMPO) were purchased from Aldrich, K2Cr201 from Fisher and used without further purification. All experiments were done at room temperature."

Jan 1, 1989

By P. J. G. du Toit

Coal has been mined by hydraulic means in various countries, i.e., the hydraulic excavation as well as the hydraulic transportation of coal has been practiced. The hydraulic breaking (excavating) of the coal dealt with in this report is done with a monitor directing a continuous jet of water against the coal, pressures of the water fed to the monitor range from 1500 to 2500 psi at 1000 to 2100 gallons per minute Transportation of the coal from the face is by fluming if a gradient exists in excess of 2 or, when a favorable gradient does not exist, the coal is pumped from the face by various types of pumps which can also provide a means of hoisting the coal to a higher elevation as required. This report presents: 1.) preliminary design and systems specifications of a demonstration miner (referred to in this report as a hydrominer), 2.) mining configurations showing good promise for typical U.S. thick coal seams in three seam pitch categories, (0° - 7° = Flat, 8° - 250 = Moderately pitching, 26° - 90° = Steeply pitching), along with cost and performance analyses for each system, 3.) a definition of a test program that will provide sufficient engineering data for the design of a water jet cutting head adequate to cut coal in those typical U.S. thick coal seams The cost analysis data showed hydraulic methods to be economically competitive with present thick seam raining methods. It was also obvious from studies of thick seam methods that the hydromonitor coal breaking techniques are more effective in removing most of the coal with its long reach of 60 ft. (or more), is a safer mining system, and produces very low coal-dust content in the air (usually less than 0.25 to 0.5 mg/cubic meter). It is recommended that the USBM sponsor a full fledged continuation of the hydraulic mining program: (a) lab, test, (b) preliminary field test, (c) full scale mine section demonstration.

Jan 1, 1977

By Alexander May

The Bureau of Mines conducted studies to determine if phosphogypsum, a waste material from the processing of phosphate rock, contains hazardous toxic materials as defined by the Environmental Protection Agency (EPA) and whether leaching of these toxic materials and radium may occur. Samples of the phosphogypsum stockpiled material were evaluated using the EPA extraction procedure, atomic absorption, neutron activation, x-ray diffraction, and chemical and physical means. Radiological tests performed used both the germanium-lithium and emanation methods. The data show that the phosphogypsum stockpiles are not hazardous toxic waste as defined by EPA criteria. Trace elements and radium are not leached from the phosphogypsum stockpiles. Absorption of trace elements and radium by phosphogypsum is the major reason for their not being leached. The standard error of measurement of radium concentrations was 4.7 pCi/g.

Jan 1, 1983

By Paul M. Tyler, R. M. Santmyers

Platinum and its allied metals osmium, iridium, rhodium , palladium, and ruthenium are the most costly of the better-known metals and combine properties that make them unique among the elements . For a number of isolated uses substitutes have been found which are cheaper and quite as satisfactory ; but none will replace platinum in many of its varied uses , and there is a large and growing demand for purposes for which no economical substitutes are known . As this paper is being written the supply of platinum tends further to increase as a result of the exploitation of newly developed resources and the expansion of production from older sources . In obedience to economic law prices have declined steadily . Buyers , always reluctant to commit themselves on a falling market , have maintained a waiting attitude , and consumption trends are not clearly indicated . Should platinum again approach the price of gold , the natural tendency would be to use more of the metal . In recent years , however , the industrial and scientific uses of platinum have become subordinate to its consumption in jewelry . In matters of personal adornment the popular whim and not practical utility is the dominant factor in demand , and it does not follow that lowered prices will stimulate demand . The substitution of white gold and certain plated goods for platinum may be checked by cheaper platinum , but a fickle public that turned from gold to platinum when platinum became the more costly metal can not with certainty be expected to buy more platinum jewelry because more of the metal than formerly may now be had for the same price . The dearth of platinum during and for some years after the World War had a profound effect upon prices , and this in turn wrought important changes in the field of consumption . When prices advanced the chemical industry, formerly the leading consumer of platinum, was forced to economize in its consumption of the metal and to substitute other metals whenever it could . Somewhat similar conditions resulted in the electrical industry and in the use of platinum in dentistry . Some of these former outlets are permanently closed , and others may be reopened now that platinum prices have receded to pre-war levels , but despite the general expansion of industrial and scientific activity since 1913 the demand for platinum outside the jewelry trade has suffered a net decline . Since the metallurgy of platinum is relatively simple the reason for its high price is its relative scarcity in the earth's crust . An interesting speculation set forth by certain geologists attributes the extraordinarily high density of the interior of the earth in part to the presence of iron alloyed with substantial amounts of platinum and other related metals . In support of this hypothesis it may be said that platinum is often found in meteorites , and known deposits in the earth's crust are all of deep - seated origin . However , even if there were a high concentration of platinum in the interior of the earth it would be next to impossible at the present state of our knowledge to make it available , and the world would continue to depend for its supply on deposits found within minable depths below the surface . For many years before 1914 the world obtained its supply of platinum metals primarily from Russia , which before the war produced as much as 300,000 troy ounces in a year , or approximately 95 per cent of the world output . Despite fluctuations due to internal political disturbances Colombia managed to account for 3 to 4 per cent , leaving the rest of the world to furnish the remaining 1 to 2 per cent .

Feb 1, 1931

By Robert E. Manning

At present, a need exists for more effective noise control in the coal-mining industry. In particular, new muffler designs with the required acoustic performance are needed for percussive pneumatic drills. Accordingly, the U. S. Bureau of Mines issued a contract to USS Engineers and Consultants to design a muffler capable of attenuating the noise from the air exhaust of a pneumatic drill. The specific objective of the contract was to design and deliver a prototype muffler that would attenuate the air-exhaust noise to 90 decibels on the A scale (90 dbA). The test drill used in this investigation was one used for roof-bolting purposes in coal mines. Using the combined approach of analysis by digital-computer program and experiment by simulated-noise tests, three prototype mufflers were designed and constructed at U. S. Steel Research. The mufflers consisted of a variety of resonator chambers and expansion-contraction chambers, and were of the following sizes: A muffler with a 3- by 5-inch elliptical cross section and about 8 inches in length. A muffler 5 inches in diameter and about 5-1/2 inches in length. A muffler 5 inches in diameter and about 10-1/2 inches in length. These mufflers were subjected to laboratory tests to determine their effectiveness in attenuating exhaust noise, mechanical noise, total drill noise, and simulated noise. All mufflers reduced the exhaust-noise level by about 25 dbA - from about 115 dbA without a muffler to below 90 dbA with a muffler - and thus were successful in meeting the contract objective. Field tests were conducted with the three prototype mufflers at U. S. Steel's Robena No. 4 Mine, and no icing problem was encountered. A fourth prototype muffler was designed to fit around the leg of the pneumatic drill. Tests showed that this kidney-shaped muffler also reduced the air-exhaust noise to below 90 dbA.

Jan 1, 1973

By E. G. Valdez

Three cryogenic systems that utilized liquid nitrogen, dry ice, and methanol with dry ice were investigated in conjunction with crushing and classifying techniques. The systems were used to aid in separating and reclaiming the metallic components contained in insulated wires, shredded automobile nonferrous metal concentrates, small motors, generators, and rubber tires. Wire strands, 2 to 6 inches long and insulated with polyvinyl chloride and neoprene, were chilled at -60° and -195° C, then roll-crushed and processed by water elutriation; this procedure resulted in two products--a sink fraction that was 99 percent metallic and a float fraction that was 99 percent nonmetallic. Excellent separation of zinc die-casting alloys from copper and aluminum contained in shredded automobile nonferrous metal concentrates was attained by chilling at -72° C for 1 minute, crushing in a grateless hammer mill, and screening. From the screened products, 97.2 and 100 percent of the copper and aluminum, respectively, were recovered in the plus Pinch fraction, and 100 percent of the zinc was recovered in the minus 1-inch fraction of over 97 percent zinc die-cast purity. Laboratory experimental results comparing direct and indirect chilling indicated that a sufficiently low temperature could be attained by indirect chilling to permit use of a liquid C02-dry ice system on insulated wires and mixed nonferrous metallic concentrates.

Jan 1, 1973

A compilation of papers presented at the Fifth WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on July 30, 31, and August 1, 1980. Papers cover areas of electromagnetics/power systems, power systems, monitoring and control, and communications.

Jan 1, 1980

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By F. E. Joyce, Charles Prasky

This report describes the response to high- temperature sulfatization of a variety of manganese minerals and companion compounds which may occur either as a principal component or as a gangue material in low- grade manganese deposits . Fourteen manganese samples representing oxide , carbonate , and silicate minerals as well as seven compounds which might occur as gangue with manganese minerals were tested batchwise in a bench- scale apparatus under conditions which would be favorable for the sulfatization of manganese . The manganese minerals substantiated thermodynamic predictions and responded to sulfatization but to varying degrees . The gangue materials , MgO , MgCO,, CaO , and CaCO3 , were sulfatized readily in contrast to the iron oxides and the aluminacontaining material which were not .

Jan 1, 1964

By Robert W. Geehan

"INTRODUCTION The Bureau of Mines, in cooperation with the Federal Geological Survey, explored the Crowell fluorite mine by core drilling in 1945. Claims investigated are in sec. 14, T. 12 S. R. 47 E., M. D. B. & M., in southern rye County, Nev., about 5 miles east of 'Beatty.The twelve holes drilled by the Bureau totaled 3,661 feet. During 1945 the mine operator drove extensive exploration drifts, in part to verify results of the Bureau's work. The drilling program was designed to test for extensions of ore bodies known in the mine.The Crowell mine has shipped Ore to steel plants on the west coast for the past 20 years. During the war this market called for all the fluorite the mine could produce, but previously there were periods when it was difficult to sell ore or concentrates.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is due to Glenn Allen, district engineer;A. C. Johnson, chief, Reno Division, Mining Branch; S. R Zimmerley, chief, Salt Lake City Division, Metallurgical Branch; W. R. Thurston of the Federal Geological Survey for advice on geological problems; and J. Irving Crowell, Jr., operator of the property, for his cooperation."

Nov 1, 1946

By Lloyd A. Morley, Alan M. Christman

1. Anonymous. "Getting Down to Earth," booklet 25T, James G. Biddle Co, Plymouth Meeting, Pa. (1970) pp. 1-48. 2. Anonymous. "Megger Ground Tester, Special Instructions," booklet 25-J-1, James G. Biddle Co, Plymouth Meeting, Pa. (1961) pp. 1-16. 3. AIEE Committee. "Application Guide on Methods of Substation Ground¬ing," AIEE Transactions on Power Apparatus and Systems (April 1954) pp. 271-277. 4. AIEE Committee. "Voltage Gradients Through the Ground Under Fault Conditions," AIEE Transactions on Power Apparatus and Systems (October 1958) pp. 669-692. 5. American Standards Association. "American Standard Safety Rules for Installing and Using Electrical Equipment in and about Coal Mines," U. S. Bureau of Mines Information Circular 8227 (1964). 6. Armstrong, H. R. "Grounding Electrode Characteristics from Model Tests," AIEE Transactions on Power Apparatus and Systems (December 1953) pp. 1301-1306. 7. Beck, Edward. Lightning Protection for Electric Systems, McGraw¬Hill, New York (1954) pp. 281-295. 8. Bellaschi, P. L. "Impulse and 60 Cycle Characteristics of Driven Grounds," AIEE Transactions (March 1941) pp. 123-128. 9. Bellaschi, P. L. "Lightning Strokes in Field and Laboratory," Elec¬trical Engineering, Vol. 58 (November 1939) pp. 466-468. 10. Bellaschi, P. L., Armington, R. E., and Snowden, A. E. "Impulse and 60 Cycle Characteristics of Driven Grounds-II," AIEE Tran¬sactions (1942) pp. 349-363. 11. Bewley, L. V. "Theory and Tests of the Counterpoise," AIEE Transac¬tions (August 1934) pp. 1163-1172. 12. Brereton, D. S. and Hickok, H. N. "System Neutral Grounding for Chemical Plant Power Systems," AIEE Transactions on Applica¬tions and Industry (November 1955) p. 315. 13. Bruce, C. E. R. and Golde, R. H. "The Lightning Discharge," Journal of the Institute of Electrical Engineers, London, Vol. 88 (December 1941) pp. 487-505.

Jan 1, 1976

By Richard I. Miller

Science Applications, Inc. has developed for the U.S. Bureau of Mines a rapid response radon monitor capable of accurately responding within three minutes to changing radon levels of magnitude from 100 to 10,000 pCi/1, typical of the levels in working uranium mines. The instrument weighs 17 pounds, is sized 12" x 10" x 6", and is capable of 8 hours of continuous portable operation with a self-contained, rechargeable battery power source. Residual chamber contamination from a radon level allowed to remain in the chamber for 90 minutes is about 10 percent, decaying about a factor of two in one hour. The instrument sensitivity is a nominal 0.1 cpm/(pCi/1), with a background count rate of less than 1 cpm.

Jan 1, 1979

By Ginger S. Evans

This report documents a preliminary hydrologic investigation of an area where longwall mining methods are to be used. The scope of work includes: determination of physical and chemical characteristics of major soil types in the area; determination of physical and chemical properties of surface water bodies; collection of geologic characteristics, including stratigraphy, structure, and detailed aquifer descriptions; collection of 10 years' meteorological data and installation of a weather station; and a detailed ground-water investigation that includes completion of observation wells, aquifer testing, water quality sampling, and analysis using a 3-D computer model. The Trescott model developed by USGS was used to simulate steady-state aquifer conditions. Input data from 8 multiple-completion monitor wells were used to model an area of approximately 10 square miles. Two layers, coal and overburden, were simulated, both confined. Model results showed good agreement with know piezometric data, desaturated areas, and flow from springs. The study area was found to have very low-yield bedrock aquifers with transmissivities ranging from 5 to 320 ft2/day for the coal (depths from 500 to 1,200 ft) and from 499 to 576 ft2/day and fractured sandstone units (depths less than 100 ft). Annual precipitation and recharge are very low, 10 to 11 inches and 0.25 inch respectively. The area has very high relief and large areas of rock outcrop. No perennial streams are present on the site.

Jan 1, 1983

By H. C. Fuller

Rhodonite, a manganese silicate, occurs as an important component of extensive veins in the San Juan district of Colorado. Recent work by the Bureau of Mines has demonstrated that typical ores of the area can be upgraded to about 30-percent manganese content. Because of their siliceous nature, such concentrates require further processing to convert the manganese into more usable forms. The investigation described in this report demonstrates the technical feasibility of producing silicomanganese from a rhodonitic concentrate by electric smelting methods. The rhodonitic concentrate used in the smelting research was prepared by dry high-intensity magnetic separation of ore from the Silver Queen vein. The concentrate contained 29 percent manganese, 2 percent iron, and 41 percent silica. The principal minerals in the concentrate were 35 percent rhodonite, 30 percent rhodochrosite, and 25 percent quartz and chalcedony. Limestone was used as the flux and coal was used as the reductant. These minerals were crushed and screened to minus 1/2-inch plus la-mesh size.

Jan 1, 1962

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative faze positions are tabulated for 160 subsidence monuments. Measurements were taken 32 times during the 2 years it took to mine the two panels. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By R. V. Ramani

This report is volume 3 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Methane Generator subsystem of the Master Design Simulator. This subsystem is used to determine methane emission rates into the mine environment. These flow rates are then used by the simulator in planning primary and secondary ventilation systems, planning a methane drainage system, and analyzing complex ventilation networks. Both steady state and unsteady state gas flows are included, and have been modeled as second order nonlinear partial differential equations. Finite difference equations are used to obtain numerical solutions to the models using a central differencing scheme. An application of the model is presented. The appendices include derivation of the gas flow equations used in the model as well as a users manual for the computer program.

Jan 1, 1974

By Phillip N. Yasnowsky

This Bureau of Mines publication tabulates State taxes levied on nonfuel minerals that have the characteristics of a severance tax.

Jan 1, 1978

By R. R. Sayers

"According to the dictionary,3 an accident is an event that takes place without one's foresight or expectation, often an undesigned, sudden, and unforeseen occurrence of an afflictive or unfortunate character. However, actual experience with accidents, the second most important cause of death in the United States,4 and a more extensive and scientific inventigation of their causes indicate that from 75 to 90 per cent of accidents are avoidable.5 This is borne out by the results of a three-year study of the accident records of 64,000 motor vehicle operators in New York6 which show that certain drivers are prone to accidents, that accident experience is traceable to certain causes, and that accidents don't just ""happen,"" It is estimated that 97,000 persons were killed by accidents in the United States in 1929 and 15,000,000 were injured. Of these about 23,000 deaths were due to so-called industrial accidents. In a list of accident rates by industries, compiled by the National Safety Council7 from reports of member establishments, mining heads the list, in both frequency (74.43 per 1,000,000 man-hours worked) and severity (9.9 days lost per 1,000 man-hours worked). These figures are very much higher than for any other industry; theindustries showing figures most comparable to mining are meat packing with a frequency rate of 55.94 and a severity rate of 1.47, construction with a frequency rate of 50.41 and a severity rate of 4.62, and refrigeration with a frequency rate of 43.35 and a severity rate of 3.04.While there is no way to determine the actual cost of all accidents from a monetary standpoint, estimates indicate that the cost will run into hundreds of millions of dollars annually.Cost of accidents in metal mines.- The United States Bureau of Mines obtains accurate figures on the number of lost-time nonfatal accidents as well as fatal accidents in the metal-mining industry.8 In 1926 the metal mines employed 127,823 men; 430 men were killed and 30,350 men received lost-time but nonfatal injuries as a result of accidents. Each of these fatal and nonfatal injuries averaged 114 days lost time, computing a fatality as 6,000 days lost time. This is equivalent to 3,523,944 days time lost due to accident, or at $5 per day per man, to a wage loss of $17,619,720. Deducting one-ninth of this figure for compensation paid, the metal miner loses in wage annually about $15,700,000, or about $122 per individual. This average loss per individual includes the cost of fatal accidents reckoned at 6,000 days or $30,000, but even if the loss in time due to fatal accidents be deducted, the average cost to each individual metal miner each year for nonfatal accidents is about $32. Estimating the loss to the metal-mine employer as about the same as that to the employee, the annual cost of metal-mine accidents to the employer is about $15,700,000 and to the employer and miner is $31,400,000."

Oct 1, 1930