Search Documents

By M. E. Poad

Structural properties of steel-fiber-reinforced shotcrete and polymer-impregnated shotcrete, both plain and fiber-reinforced, were investigated by the Federal Bureau of Mines, Spokane Mining Research Center. The research center has found that flexural strengths can be increased by as much as 106 percent, and splitting-tensile strength by 50 percent, by introducing randomly oriented steel fibers. A slight decrease of compressive strength was found in the fiber-reinforced shotcrete. Polymer-impregnated shotcrete exhibited a threefold to fourfold increase in compressive and splitting-tensile strength. The techniques of preparing shotcrete with the dry process, using both fast-set agents and regulated-set cement, are described, along with the results of physical-property testing. Physical properties include compressive and splitting-tensile strengths, tangent and secant moduli, and stress-strain curves for plain shotcrete, fiber-reinforced shotcrete, and polymer-impregnated plain and fiber-reinforced shotcrete. Flexural strengths for plain and fiber-reinforced shotcrete are also reported. Steel-fiber shotcrete is the more promising of the new structural materials for ground support, and additional research is recommended.

Jan 1, 1975

Coal, America's most abundant fossil fuel, is expected to play a key role in our pursuit of energy independence. A substantial increase in coal exploitation will be required if we are to fulfill our future energy needs. It is essential that new developments continue if stable coal prices are to be achieved and maintained. The challenge of the mining industry is to continue these developments in the face of problems related to increasing labor costs, inflation and environmental restoration. With expectations of increased activity in surface coal mining, the U.S. Bureau of Mines has authorized this study to determine the preliminary economic and technologic feasibility of underspoil haulage in area strip coal mines and to identify geologic and geographic areas where such a system could be used. These objectives were met by literature search, data-gathering visits to several active area strip mines and by analyzing various haulage systems that were superimposed on three model mines. Potential advantages of such a system include: 1) improved mine design; 2) lower mine operating costs; 3) improved land reclamation; 4) lower manpower requirements; 5) lower mobile equipment requirements; and 6) smaller, less sophisticated maintenance facilities.

Jan 1, 1975

By Walter D. Holland

This study was undertaken to determine miners' breathing zone concentrations of diesel exhaust components, to investigate any relationships between these concentrations and vehicle type, the presence of emission controls, vehicle usage, and ventilation conditions, and to make recommendations for monitoring and ventilation requirements. Twenty-four mines including two con l mines were surveyed. Sampling was done for CON, NON, SOx, PNA, aldehydes, and particulates. hi most mines, concentrations of at least one contaminant exceeded one half the standard or TLV. The concentrations of gases arc probably sufficiently reduced by a minimum air velocity of 50 fpm. A sufficient reduction of particulate concentrations may require as high as 400 fpm air velocity. Vehicle age, type, or usage appear to have little or no effect on contaminant concentrations. PNA levels were below detection limits in all but a very few samples. Minimum requirements for routine monitoring should include formaldehyde, COx, NO2. It is further recommended that better definition of the minimum ventilation requirement be obtained.

Jan 1, 1978

By Fred Leighton

The Bureau of Mines has developed rock noise source location techniques that may be used to obtain precise and practical source locations from micro-seismic field data. These techniques enable one to monitor all or any part of a rock structure and map progressive stress buildup or rock movement. Thus, the microseismic method of determining instability in rock structures is becoming an invaluable engineering tool for the mining or civil engineer engaged in rock excavation and construction.

Jan 1, 1970

By Donald C. Strimbeck

The Bureau of Mines designed a down-fired refractory-lined combustor that efficiently burned pulverized coal to produce a gas suitable as working fluid for an open-cycle gas turbine. The gas contained relatively little carbon, so the load on the ash-separation equipment was significantly reduced. Moreover, reduction in carbon content of the gas increased the average density of the solid particles making them more amenable to removal by centrifugation. Centrifugal-type separators failed to remove sufficient ash; however, to limit blade wear enough to achieve operating periods generally deemed necessary for commercial practicability.

Jan 1, 1969

By R. V. Ramani

This volume is the first of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume II: Dragline Model, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. This report deals with the development of a geological model for surface mine planning. The most common orebody modeling techniques are described. A brief review of geostatistical theory and concepts is presented. A geostatistical option for orebody modeling is developed and validated. Computer programs and sample outputs are appended.

Jan 1, 1985

By J. Mitchell Linnet

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of deposits in the Bucks Lake and Chips Creek RARE II areas in Plumas and Butte Counties, California. These areas lie along the west slope of the Sierra Nevada on opposite sides of the North Fork Feather River and encompass an area of 62,800 acres (25,400 ha). Metasedimentary and metavolcanic rocks of the Pennsylvanian Calaveras Formation are intruded by plutons of Mesozoic age. Mineral; of economic iterest are in quartz veins in metasediments close to these plutons; they are principally gold and silver with minor amounts of copper, lead, and zinc minerals. Molybdenum, copper, silver, and tungsten minerals occur in tactite along metasedimentary-granitic rock contacts. In both areas, auriferous Tertiary channel gravels have been extensively developed. Asbestos occurs in ultramafic rocks in both areas, and a limestone deposit was explored in the Chips Creek area. Gold is the principal economic mineral in the Bucks Lake RARE II area. The Shenandoah Mine (fig. 1, no. 19) contains 7,500 tons (6,800 t) of indicated and inferred subeconomic gold resources in sulfide-bearing, silicified metamorphic rocks of the Calaveras Formation (table 1). Similar rocks have yielded gold at the Edman and Megowen Mines, adjacent to the area. A high potential exists for additional lode resources in the area around the Shenandoah Mine. Callahan Mining Corporation personnel believe a multi-million ton disseminated gold deposit underlies the property.

Jan 1, 1983

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983

By B. C. Peterson

Calumet Division, Calumet & Hecla, Inc., whose operations are in Houghton and Keweenaw Counties, Mich., is a highly integrated and complex organization. This division operates mines, a railroad, a concentrating mill, a reverberatory smelter, and the auxiliary generating plants and shops to service these operations. In addition, it operates a sands reclamation plant, leaching plants, a foundry, and a machine shop that serves varied industries with castings and parts for many applications. Calumet & Hecla, Inc. has produced over 60 percent of all the copper that has been produced in Michigan since discovery of the ore in 1864, and in 1959 the company ranked eight among the country's producers with a production of 17,407 tons. To keep abreast of modern accounting systems developed elsewhere in industry and to combat increasing costs due to higher labor and supply costs, as well as increased costs due to deeper mines and lower grade ore, the company has developed a modern machine cost accounting system. This not only provides the usual bookkeeping and cost accounting facilities but offers accurate cost data for engineering evaluation of the mining operation. This system is credited with being instrumental in permitting continued operation of these high-cost mines in a period of increasing costs with no corresponding increase in the price of metal.

Jan 1, 1962

By J. C. Engel

Recent innovations in mine safety include the use of mercury vapor lamps for mine vehicle illumination. Such lamps, however, extinguish whenever the line voltage at the machine momentarily sags or is interrupted. The lamps must then cool for several minutes before they will restart. By supplying reduced high frequency power to the lamps from an auxiliary source, it is possible to maintain ionization in the arc tubes preventing the lamps from extinguishing. Essentially an auxiliary high frequency supply, the keep alive system provides additional power to the lamps automatically whenever the lamps are in danger of dropping out. The system can also provide the operator with the ability to dim the lamps at will for periods of up to three minutes by simply interrupting the 60 Hz power to the conventional ballasts. Each unit, housed in a steel explosion proof enclosure with a volume of approximately 0.6 ft3, is capable of servicing up to six 175 watt H-39 mercury lamps and two 100 watt H-75 reflector flood lamps. A total of 16 units were produced for the USBM under this contract and its extension.

Jan 1, 1979

In attempting the predict coal cleat orientation in the subsurface for effective methane degasification of the coal beds in the Warrior coal field of Alabama, approximately 150 rock joint orientations and 45 coal cleat orientations were measured in each of 37 7 ½ minute quadrangles in Tuscaloosa, Walker, Jefferson, Fayette, Winston, Blount, and Bibb Counties. Data from these surface locations, and coal cleat data from eight underground mines was corrected for magnetic declination and titled beds rotated to the horizontal where necessary and plotted on rose diagrams for comparative analysis. Data collected on each joint and cleat consisted of attitude, quality, type, spacing, persistence, lithology, bedding thickness, surface texture, and filling. File data and published and unpublished reports from the State Survey and the State Mine Inspector's Office were re-viewed. Twenty-seven mining companies, most of which supplied information pertinant to the project were also contacted. The information obtained consisted of crop line information structure, and underground mine outlines, all of which were put on 7 ½ -minute topographic quadrangles. LANDSAT-1 imagery and Skylab photography were compared to dominant joint and cleat trends in the study area. Detailed results can be found in an open-file report entitled "Fracture Analyses in a Selected Area of the Warrior Coal Field, Alabama." A master's thesis entitled "The Relationship Between Surface Joints and Subsurface Structure in a Selected Area of the Warrior Coal Field" is being prepared to illustrate the relation-ship of the fracture system to the structure in the Warrior coal field. A proposal has been submitted for research on a project entitled "Rock Fracture Systems and Their Affects on the Extraction of Fossil Fuels in the Warrior Basin, Alabama"

Jan 1, 1976

By Dale William Avery

Thirty mines and prospects were studied; 22 are within the Dolus Lakes RARE II area. Three properties within the area and one adjacent to it were determined to have indicated or inferred gold, silver, or molybdenum resources (fig. 1 and table 1) associated with quartz veins and shear zones or quartz-pyrite stockworks in granodiorite. Five other properties in the area and three just outside have potential for the discovery of gold and silver resources. Minor amounts of very fine-grained placer gold are in glacial outwash in and near the area. The John G. Carlisle Mine (fig. 1, no. 9) produced 120 oz (3.7 kg) of gold between 1897-1899. The Independence Mine produced 481 oz (15 kg) gold, 197 oz (6.1 kg) silver, and 189 lb (86 kg) of copper between 1926 and 1935. These mines are adjacent to the study area's northern boundary.

Jan 1, 1983

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

By E. W. Dean

The Bureau of Mines is engaged in the work of obtaining data regarding the physical and chemical properties of typical crude oils from the various producing fields of the, United" States. Preliminary reports have been published that cover the eastern fields* and the' Rocky Mountain districts.** Since the appearance of these, reports: it has been suggested that certain additional data. I regarding the samples would be of practical value. It was believed that a knowledge of the viscosity of crude oil was desirable, particularly in connection with the design and operation of pipe lines. In accordance with this suggestion, the authors have made viscosity tests upon as many of the samples of the two series as wore still available for examination. Determinations were made at temperatures of 70° and 100°F., and in addition the oils were Subjected to the A. S. T M, pour-test*** to as certain the lowest temperatures at which they remain in a fluid condition.

Jan 1, 1921

This appendix is composed of five sections, each of which is tabbed for ease of access. The sections are as follows: ? Fire incident report forms for underground mine fires. There is one form for each incident listed in Table II-1a. They are ordered chronologically with incident numbers corresponding to those in Table II-la. ? Fire incident report forms for surface mine fires. There is one form for each incident listed in Table II-lb. They are ordered chronologically with incident numbers corresponding to those in Table II-lb. ? Journal article report forms. There is one form for each article reviewed. They provide supplemental information to that contained in the fire incident report forms for selected fires. Index 11-14 keys the journal article report forms to the appropriate fire incident report forms. ? Non-reportable incident descriptions for underground mine fires. This is a listing of underground fires for which MSHA regulations do not require formal reports. ? Non-reportable incident descriptions for surface mines. This is a listing of surface fires for which MSHA regulations do not require formal reports. This appendix is intended to be used in conjunction with the tables and indexes contained in Volume II of this report and, as such, should be considered an integral part of Volume II. The indexes in the body of Volume II provide a means of ready reference to the underground and surface mine incident report forms. For those readers with interests other than those indexed, Tables II-la and II-1b can be used to locate specific incidents of interest. Complete incident information can then be obtained from the corresponding report forms in the first two sections of this appendix.

Jan 1, 1980

By Noel N. Moebs

The U.S. Bureau of Mines is conducting research on many topics relating to the mineral resources of the United States. This is done to ensure an adequate supply of minerals essential to a viable domestic industry and a sound economy. The United States is almost totally dependent on foreign supplies for a number of minerals such as chromium, niobium, tantalum, and manganese for which there is no available substitute, while many other minerals such as titanium are abundantly distributed throughout the earth but seldom occur in adequate concentrations or useful forms. This report describes an example of a small but high-grade occurrence of titanium are in Nelson County, VA. This occurrence could be exploited under favorable economic conditions with new mining technology such as borehole slurry mining. The report demonstrates that the dikes at titanium ore, a mixture of ilmenite and apatite locally termed nelsonite, can be detected and traced along strike using magnetometer traverses. This information will aid in the selection of appropriate slurry borehole mining test sites in the area.

Jan 1, 1993

By F. E. Brantley

Research was undertaken by the Bureau of Mines to assess the technical feasibility of smelting cement-copper precipitate in an electric furnace to produce commercial-grade copper. The blister-grade copper produced in smelting was refined by gaseous oxidation and reduction methods to rive a product equal in quality to fire-refined copper. The cement copper used in the study was typical of the material produced in commercial operations. The sample product was received in a partially oxidized state and analyzed 77.5 percent Cu, 3.4 percent Fe, 0.8 percent Pb, 0.05 percent Ni, 0.6 percent Sn, and 0.9 percent S. Smelting tests were made on the precipitate using laboratory-size induction and electric-arc furnaces. Three types of furnace linings were tested during, the investigation: Carbon, including graphite; clay-graphite; and silicon carbide. Although all proved satisfactory, either carbon or graphite was preferred because of their superior refractory properties and low permeability to molten copper. Copper recoveries in the induction and arc smelting tests averaged 92 percent in commercial-grade metal assaying 99.8 percent copper. Refining the molten copper by oxidation and gaseous reduction or by chlorine lancing increased the purity to plus 99.9 percent.

Jan 1, 1961

By David A. Larson

Preliminary laboratory experiments have been conducted by the Bureau of Mines to define the influence of bit geometry on methane ignitions as a step toward establishing safer mining-machine operating parameters. The experimental system was designed to simulate the operation of a continuous mining machine, using a drum-type cutterhead of normal diameter with a narrow cross section, permitting full-diameter drum cutting tests to be run on material representative of sandstone lenses (or inclusions) in coal seams. Two conical bit types were tested at shallow depths of cut with three drum speeds. Bits that rotated in the mounting block during testing did not produce ignitions. The ignition frequency for used bits was three to four times greater than for new bits at the same kerf depth.

Jan 1, 1983

This report provides concepts for two automated longwall mining systems; one for operation in a 42 to 57-inch thick section of the Lower Kittanning coal seam, the other in a 57 to 72-inch thick section of the Pittsburgh seam. The Lower Kittanning concept uses a single-drum bidirectional shearer and 500-ton capacity 4-leg chocks and the Pittsburgh concept uses a double-drum shearer with 500-ton shields. Each concept is designed to produce in excess of 2,500 tons of clean coal per shift with a 6-man face crew. The automated longwalls consist of off-the-shelf control system hardware attached to standard longwall equipment. Control hardware includes a control and display console; prime and backup mini-computers; multiplex data transmission, power, and control lines; several remote terminals which serve as interface junctions; and various sensors and actuators located on the longwall equipment. The system can be operated either fully automatically, remotely or manually.

Jan 1, 1976

By Joseph Grumer

An instrumented spherical vessel has been used for many years to study laminar combustion waves. Concurrent measurements of flame speed and pressure-rise rates have led to evaluations of burning velocities, the pressure dependence of the burning velocity, and the expansion ratios of the gases passing through the combustion wave. For the most part, these studies have involved flames initially at atmospheric or subatmospheric pressure. The old spherical vessel used by the Bureau of Mines was not designed for use at elevated pressures. Moreover, being made of wrought iron, it was susceptible enough to corrosion to prohibit its use with many combustible mixtures that figure in industrial research. In mid-1956, under sponsorship of the Office of Naval Research, the Bureau undertook the development of a stainless steel spherical vessel capable of withstanding explosions of gaseous mixtures at initial pressures as high as 20 atm. and initial temperatures as high as 250° C. The design called for a double array (cross) of closely spaced small windows for observation of the flame as it traversed the vessel and a piezoelectric transducer to measure concurrently pressure-rise rates. Because no commercial contractor was willing to bid on the construction of such a vessel, it was built at the Bureau's Bruceton machine shop.7

Jan 1, 1961