Search Documents

By Charles P. Lazzara, Alex C. Smith, Richard W. Pro, Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressure New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 1993

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

By Charles H. Simmons

Two versions of a VF transceiver to aid in location of trapped miners has been developed and tested. The belt worn model was produced in both transmitter and transceiver configurations. In addition, a quantity of the belt worn models were fabricated using aluminum wire instead of copper in order to reduce unit weight. Ten prototypes of a battery cap model VF transceiver were also fabricated demonstrating further unit size and weight reduction while maintaining electrical performance. Samples of- both versions were tested environmentally and the test data is included in this report. While both versions of the VF transceiver are similar electrically, and are constructed using convential manufacturing techniques, the battery cap model realizes a lower total weight, smaller volume and production cost than the belt worn version. Operationally, the battery cap model assures that the VF transceiver will always be with the miner.

Jan 1, 1981

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $20,799,800 for the 1 .06- million-ton-per-year (MM tpy) mine to $84,027,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $32,506,800 to $1 22,983,500 for the same mines. Corresponding selling prices for the coal range from $12.87 to $11.64 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1976

By R. A. Kearns

Biennially the Bureau of Mines issues a list of equipment that has been accepted as approved or permissible during the two calendar years immediately preceding the date of publication of the listing. By so doing the mining industry is kept informed of the availability of the latest equipment for safe use underground. This list supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953; Information Circular 7722, Permissible Mine Equipment Approved During the Calendar Years 1953-54; Information Circular 7840, Permissible Mine Equipment Approved During the Calendar Years 1955-56; and Information Circular 7957, Permissible Mine Equipment Approved During 1957-58. This list includes equipment meeting those standards that have been revised since Information Circular 7957 was .issued. Schedule 16E,4 a revision of Schedule 160, was approved May 19, 1960.

Jan 1, 1961

By James R. Dunn

Samples were taken of industrial mineral waste materials which are potentially capable of being used for filling underground coal mines for subsidence control in the Pittsburgh and the Scranton-Wilkes Barre areas of Pennsylvania. The samples were subjected to potentially relevant standard tests which are commonly used 1n the evaluation of soil materials and mineral "aggregate materials. Measurements of plasticity, liquid limit, and gradations, particularly in the -200 mesh size range, indicated a comparative lack of clay minerals. Cementitious reactions between sources of alkali, such as calcium hydroxide or portland cement stack dust, and of silica, such as clay or fly ash, were found to occur in various mixes of high-bulk materials. Strengths of up to about 400 psi at 84 days were observed. The possibility of emplacement of high-bulk material by both turbid flow (or density currents) below water and by mud flows above water were considered and both appear to be reasonable and possibly simpler than the current mechanisms of emplacement.

Jan 1, 1977

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982

By J. E. Rourke, O&apos

This report incorporates a review of available dewatering technology and an evaluation of its relevance to surface coal mines in the Interior Province of the United States. Guidelines for the selection, design and construction of dewatering systems are included. On the basis of documented experience, candidate dewatering systems were selected and evaluated with respect to their anticipated impact on the environment and mine operations. Included in the discussion is a summary of laws and regulations which can impact on dewatering operations. Following this discussion, geologic and hydrogeologic conditions within the Interior Province are described and potential dewatering problems at surface coal mines are identified. Model mines are developed which exhibit the most difficult dewatering problems identified, and it is demonstrated how available technology can be utilized to deal with these problems. Dewatering of coarse-grained, high permeability terrace deposits might be economically feasible today. Low permeability, saturated glacial tills or lake deposits appear to be significantly outside present economic feasibility for dewatering.

Jan 1, 1979

By Ren G. Dong, Jay Kim, Daniel E. Welcome, Won Joon Song, Charles Hayden

Prolonged, extensive exposure to hand-transmitted vibration could cause a series of vibration-induced disorders in the vascular, sensorineural, and musculoskeletal structures of the human hand-arm system, which have been collectively called hand-arm vibration syndrome (HAVS).1 To assess the risk of HAVS the international standard ISO 5349-1 (2001)1 recommends using the root-mean-square (rms) acceleration of the measured vibration with a frequency weighting. While a few epidemiological studies have reported results consistent with the predictions made according to the recommendation, many other studies have reported results with large discrepancies.2 This may be partially attributed to the time-averaging effect involved in calculation of the frequency components, especially for impact type tools. Because the spectral characteristics of impact tools change dramatically with time, a time-frequency (T-F) analysis can provide better characterizations of such highly transient vibrations. The analytic wavelet transform (AWT) is an ideal T-F analysis tool because it possesses the advantages of both the Fourier transform and the wavelet transform.3 The objective of this study was to explore the application of the AWT method for characterizing the impact tool vibrations and assessing their exposure risk. Methods Five tools (two chipping hammers, two riveting hammers, and one concrete cutting saw) were used in this study. The saw vibration was measured when it was used to cut a section of road pavement during a repair. The vibrations on the other tools were measured by the procedure specified in ISO 8662-2 (1992).4 A sampling rate of 16,386 Hz was used in the measurement. The AWT and Fourier analysis were applied to these signals and to identify their characteristics. Results Figure 1 compares the T-F characteristics of the accelerations measured from the relatively steady concrete saw and a riveting hammer. The frequency weighting specified in ISO 5349-11 was applied in the calculations. The comparison clearly shows that the two tools have completely different T-F characteristics.

Jan 6, 2006

By William A. Stickney

The zirconium-hafnium separation plant at Albany, Oreg., was the result of a chain of events that started with studies by A. R. Kaufmann at the Massachusetts Institute of Technology. Variations in the listed neutron-absorption cross-section of zirconium caused him to suspect a misprint. As a result of these discrepancies and following his suggestions, Oak Ridge scientists made studies establishing a value of 0.4 barn or lower. This meant that the potential of zirconium for reactor application was greatly enhanced. Since hafnium is invariably associated with zirconium and has a high neutron cross-section, it was necessary that an efficient hafnium-separation method be developed before the superiority of zirconium as a structural material in nuclear reactors could be realized. The Albany plant was built and operated for the Atomic Energy Commission (AEC) under Letter Agreement AT-(11-1) -140, patterned after a plant operated by the Carbide and Carbon Chemicals Corp. at Oak Ridge, Tenn. Construction was begun in April 1951. Hafnium was to be extracted preferentially as hafnium thiocyanate from an aqueous mixture of zirconyl and hafnyl chlorides in hexone (methyl isobutyl ketone) by a liquid-liquid countercurrent system.

Jan 1, 1959

In July 1982 the Committee on Underground Coal Mine Safety completed its study of safety in U.S. underground coal mines; the results of the study were published in the National Research Council report entitled Toward Safer Underground Coal Mines. One of the findings of this study was: THERE IS A STRONG CORRELATION BETWEEN MINE SIZE AND FATAL INJURIES. THE FATALITY RATE IN MINES WITH 50 OR FEWER EMPLOYEES IS NEARLY THREE TIMES THAT OF LARGE MINES (WITH OVER 250 EMPLOYEES), AND ABOUT TWICE THAT OF INTERMEDIATE-SIZED MINES (WITH 51-250 EMPLOYEES). Although the Committee explored possible reasons for the higher fatality rate in the smaller mines, it was not able to explain this phenomenon fully. Therefore the Bureau of mines requested that the Committee undertake a supplementary study of fatalities in small underground coal mines. The Committee met in the fall of 1982, discussed the problem, developed an approach to it, approved a program of statistical analyses, and authorized a panel of four committee members to explore the problem in greater depth. The panel, in turn, reviewed the results of the statistical analyses and met with the president of the National Independent Coal Operators Association and with several owners of small underground coal mines for a detailed discussion of the unique problems of small mines. Panel members examined 66 individual fatality reports prepared by Mine Safety and Health Administration (MSHA) inspectors who investigated fatal accidents that occurred in small underground coal mines in 1979 and 1980. This report is the result of those studies, analyses, and deliberations. The first draft was prepared by the panel, but the report has been reviewed and approved by the entire Committee.

Jan 1, 2011

By Marilyn Biviano

(l)The direct economic costs to this nation resulting from a decision to embargo South African strategic and critical minerals imports are estimated at $1.85 billion per year.2,3 About 94 percent of these estimated costs are for two platinum-group metals (PGM&apos;s), platinum and rhodium. The estimated costs of a 5-year embargo beginning in 1988 for the strategic and critical minerals analyzed are presented in Table 1.4 (2)There are sufficient alternative world sources to South Africa for manganese, chromium, palladium, titanium, and vanadium to meet U.S. industrial demand in the event of an embargo. (3)Alternative world sources to South Africa for platinum and rhodium cannot meet U.S. industrial demand. Non-South African world supply sources can meet about 40 percent of domestic platinum consumption requirements and 50 percent of rhodium requirements. (4)As a result of the increase in prices for platinum and rhodium during the embargo, expansion of domestic platinum-group metals mining and secondary production is expected. During a five year embargo, domestic primary and secondary production expand and together satisfy about one-third of U.S. platinum requirements, one-third of U.S. rhodium requirements, and over one-half of domestic palladium requirements.

Jan 1, 1988

By R. L. Balmer

This information circular, which describes the methods and costs of sinking a small underground shaft with steel supports at the Keystone mine of American Smelting and Refining Co., near Crested Butte, Colo., is one of a series being prepared by the Bureau of Mines on current shaft-sinking practices in various mining districts of the United States. Preparations for sinking a combined exploration, development, and production shaft from the lowest level of the Keystone mine began early in 1957. This vertical, three-compartment, 6-1/4-by 16-foot rectangular shaft was to be sunk in separate stages or lifts so as to correspond with the progress of an associated lateral exploration and development program. The first section of the shaft was collared and sunk to a depth of 209 feet between September 1957 and April 1958. Because of the depressed base-metal market, the mine was shut down as soon as the initial phase of the exploration and development program had been completed and before any deeper sinking could be attempted.

Jan 1, 1962

The Bureau of Mines is operated to assist in promoting economic development through increased efficiency in the mining, preparation, treatment, and utilization of mineral substances; to aid in conserving mineral resources through preventing waste; and to help the mining industry improve health conditions and increase safety. Accomplishment of those ends is sought through investigation of scientific, technologic, and economic problems of the, mineral industries and dissemination of resulting information. Building materials of mineral origin constitute an important product of mining, and the Bureau makes studies of these in the various fields mentioned. The following commodities come within this classification: Asbestos, anhydrite, asphalt, cement, clay and clay products, diatomite, dolomite, glass and mineral wool, granite, greenstone, gypsum, lightweight building materials, lime, limestone, magnesite, marble, sand, sand and gravel, sandstone, sand-lime brick, slate, soapstone, and trap rock.

Jan 1, 1937

By L. C. IlsLey

Many accidents rightly classifiable as electrically caused are not so classified for the reason that in numerous accidents the part that electricity played in causing the fatality is only suspected. For instance, a workman might receive a shock that would cause him to lose his balance and fall beneath a trip of cars; if no one saw the first part of the accident, the cause undoubtedly would be charged to "haulage." This paper covers a brief study of fatal and nonfatal electrical accidents. The first usually result from direct contact with the electrical circuit or electrical apparatus; the second more often are the result of arcing or flashing due to handling defective apparatus or making repairs on "live" equipment or circuits. It is hoped that helpful suggestions may be offered for minimizing accidents of these two classes.

Jan 1, 1938

By Harold Kennedy

Take a good look at this issue of Minerals and Materials. This is the last issue of M&M, as it has been known within the U.S. Bureau of Mines, that you will receive. Fifteen years after it was created to help cope with a growing worldwide mineral shortage, M&M is ceasing publication. In its place will be a bright, new publication called Minerals Today. Like its venerable predecessor, Minerals Today will be a bimonthly magazine that reports on recent trends and issues in the minerals and materials industries. It will be the Bureau of Mines&apos; most frequent periodical presenting an overview of the entire field of minerals and materials.

Jan 1, 1989

By Robert Blickensderfer

Tungsten alloys with high-temperature strength properties, comparable to the best of alloys recently developed by others, were produced by a new process called here the oxyreaction process. The process involved additions of a powder of a reactive metal compound, ZrN, ZrW2, or HfW2, to a base metal powder, tungsten, which contained some oxygen. The powders were blended, compacted, sintered, and extruded. During sintering, diffusion and internal oxidation occurred to produce reactive-metal oxide particles and solid solutions. A dispersion of oxide particles could be precipitated by heat treating. The oxyreaction process circumvents many of the agglomerating and coarsening problems encountered in the current methods for dispersing a stable oxide in a metal. Oxyreaction strengthening results from solid-solution strengthening and from dispersion strengthening produced by the reactive metal and its oxides. At a test temperature of 1,650° C, the alloys prepared from WW, had tensile strengths up to 70,000 psi and stress-rupture lives up to 142 hr at 10,000 psi stress; the alloys prepared from ZrN powders had tensile strengths up to 80,000 psi and stress-rupture lives up to 27 hr at 10,000 psi stress. Tensile strengthening in the alloys was attributed to Zr in solid solution or to Zr-O-W structures too small to be observed in an electron microscope replica. Stress-rupture life was attributed to a dispersion of submicron Zr02 particles which precipitated and grew to 0.05-to 0.2-micron size during the test. Tensile strengthening and stress-rupture life were dependent upon both the zirconium and oxygen contents with the maximum occurring at roughly 0.9 atomic pot Zr and 0.9 atomic pot 0. Studies of the details of the oxyreaction process were made on the W-ZrW2 alloys and three general steps were determined: (1) The reaction of 0 in tungsten powder with ZrW2 to form relatively large Zr02 particles; (2) the dissolution of remaining ZrW2 into the W matrix and partial internal oxidation to form ultrafine but sparse zirconium oxide particles and possibly to establish Zr-O-W structures; (3) the development of ultrafine Zr02 particles during high-temperature aging.

Jan 1, 1971

By Joseph L. Buckley

A total of 55 conveyor belt fire tests were conducted in the Bureau of Mines Fire Test Gallery, located at the Factory Mutual (FM) Fire Test Center West Glocester, R.I. The objectives of these tests were to: 1) determine the fire resistance and burning characteristics of various conveyor belt materials under simulated mine conditions; 2) provide essential data for designing a reliable bench-scale conveyor belt fire resistance test; and, 3) determine fire test conditions that will discriminate between low, moderate and high fire resistant materials. Belts, representative of those which mold he found in underground coal mines were examined under n umber of experimental conditions which included; ignition intensity; air flow rate; ratio of belt bright (h2) to overall gallery height (h1); exposure time; and, belt width. It was found that fire propagation could be achieved for some "fire resistant" belts (complying with the present Schedule 2G standard for approval) when exposed to an Ignition source of =6000 Btu/min for a 15-min period at a belt height ratio of 01.66. There appears to be a dependency of flame propagation on air flow rates and belt width, although the tests performed do not provide a quantitative trend. Recommendations are made for additional work to resolve some anomalous date and to fill voids in the rest program.

Jan 1, 1978

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966