Search Documents

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 34,000 acres of the 58,040-acre Little Jacks Creek Wilderness Study Area (ID-111-6) in order to evaluate the mineralized resources. The study area is located in Owyhee County, 10, about 21 miles southwest from Bruneau. No mining districts are in the study area, nor were any mines or claims recorded or found. The northern half of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Little Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Larry Joe Linley

The Department of the Interior, Bureau of Mines is reviewing explosion protection methods for use in gassy coal mines. This performance criteria guideline is an evaluation of three explosion protection methods of machines electrically powered with voltages up to 15 000 volts AC. A sufficient amount of basic research has been accomplished to verify that the explosion-proof and pressurized enclosure methods can provide adequate explosion protection with the present state of the art up to 15 000 volts AC. The routine application of the potted enclosure as a stand alone protection method requires further investigation or development in order to clarify performance criteria and verification-certification requirements. An extensive literature search, a series of high voltage tests, and a design evaluation of the three explosion protection methods performed at White Sands Test Facility indicates that the explosion-proof, pressurized, and potted enclosures can all be used to enclose up to 15 000 volts AC, if the performance criteria and verification-certification requirements recommended in this guideline are implemented.

Jan 1, 1982

The 1967 Lignite Symposium was held at Grand Forks, N. Dak., on April 27-28, 1967. This was the fifth of these technical meetings and the fourth which was cosponsored by the University of North Dakota and the Bureau of Mines. These symposia have provided a meeting place where current developments concerning technology and utilization of solid fuels (lignite) are presented. There was a registration of 255 persons from 24 States, the District of Columbia, six Canadian Provinces, Germany, and India. Many segments of coal or energy oriented organizations at many levels were represented. During the meeting, 18 presentations were made covering developments in electrical power generation, mining, estimation of reserves, combustion, gasification, and chemical and speciality uses of low-rank coals; these are com-piled in this Information Circular to provide a record of the symposium and to permit wider dissemination of the information. Proceedings of the other meetings have also been published.3

Jan 1, 1968

By Charles Fried

The Coal Mine Health and Safety Act passed by Congress in 1969, called for research to alleviate the occupational stresses and hazards of coal miners. Spurred by a series of recent mine disasters the Congress directed the Bureau of Mines to increase its attention to the welfare of miners and to develop better working conditions and personal equipment for use in the mines. As one of the early steps in carrying out the provisions of the Act, the Bureau of Mines commissioned the Behavioral Sciences Group at the National Bureau of Standards to conduct a survey of the state of the art in ergonomics (human factors) as it has been applied to mining.

Jan 1, 1972

By C. S. Tout

While investigating methods for determining the best temperatures for hot-working experimental stainless steels, the Bureau of Mines Albany Metallurgy Research Center developed a machine in which hot-twist tests could be made in a few minutes. This machine is similar to some used previously except that specimens are heated by induction instead of by radiation, and their temperature is measured by a calibrated radiation-detection unit instead of by a thermocouple. In. developing the technique for using the new machine, tests were made on specimens of medium-carbon steel, mild steel, and AISI (American Iron and Steel Institute) type 304 stainless steel. Tests also were made on as-cast specimens and preworked specimens of experimental AISI type 202, low austenitic stainless steel, and as-cast specimens of AISI type 301 experimental stainless steel. The optimum hot-working temperatures were determined for all types of steel tested. Also, data were gathered on the effects of test speed and temperature on torsional strength and the effect of twisting on tensile stress in the specimen.

Jan 1, 1962

By R. F. Zaffarano

Reservoir oil in the Greater Aneth area, Utah, part of the Paradox basin, was studied to detect variation in oil characteristics within the reservoir and to determine its relation to age of accumulation and fluid equilibrium. At least three subsurface oil samples were obtained from each of the four largest of five field divisions comprising a producing area of 45,000 acres. Height of the oil column in the Pennsylvanian Desert Creek zone is about 230 ft. In general, the oil characteristics were found to be uniform across the area, and averages were developed for use in engineering applications. Average saturation pressure was 1,780 psia; the oil was undersaturated at the initial reservoir pressure, 2,200 psia. Variation in saturation pressure shows a lack of complete fluid equilibrium and continuing diffusion of solution gas from the main body of the reservoir to two extensions linked by narrow arms. By assuming early accumulation, the time involved in this diffusion process was calculated to be about the same as the age of the reservoir formation. Cause of the concentration of gas in the main body is attributed to differential entrapment during accumulation of oil and gas from an exterior source.

Jan 1, 1963

By Nathan T. Lowe

This report updates an accounting of mines and prospects in the Seafoam mining district, Custer County, Idaho, begun during mineral appraisal of the Idaho Primitive Area. Thirty-two mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of mineral appraisal of the River of No Return Wilderness; most previously known locations were field checked and the updated information added to the data base. The district's major deposits include polymetallic fissure veins of gold-silver-lead-zinc-copper hosted by granodiorite and quartz monzonite which have been intruded by dikes ranging in composition from rhyolite to dacite, and vein type replacements of silver-lead-zinc-copper hosted by calcareous xenoliths imbedded in major intrusives. These deposits may be related to the intrusion of the Rapid River pluton or the Casto pluton. The dominant northwest structural trend is parallel to an aeromagnetic high, a weak gravity salient, and the Blue Bunch Mountain dike swarm.

Jan 1, 1983

By D. F. Scott

The purpose of this study was to determine if miners were at risk from exposures to chemicals used in the mining industry and determine the nature and sources of the illnesses and injuries. The U.S. Mine Safety and Health Administration?s (MSHA) employment and accident, injury and illness database was reviewed. There were 2,705 cases of chemical-related injuries and illnesses reported from 1999 through 2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker (cleaning plant operators are responsible for maintenance of plants, media operators are responsible for handling reagents, boney preparation plant operators oversee removal of ?bone? from coal, and crusher workers use large crushers to break mined material). From 1999 through 2006, the rate of ?nonfatal days lost? and ?no days lost? (resulting from injuries) did not change significantly; however, the rate of illnesses decreased significantly. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods and safety culture to ensure that their workers are protected.

Jan 1, 2009

By A. A. Cochran

The purpose of this Bureau of Mines research was to investigate the theoretical and practical aspects of using ionizing radiation to promote chemical reactions that are of interest to metallurgists, and to carry out a radiation study of a suitable reaction. The effect of 44,000 roentgens per hour of 120,000-volt X-rays on the chlorination of highly pure mixtures of rutile, carbon, and various catalysts at temperatures up to 540° C. is described. At these low temperatures, recoveries were very low; however, in the eight different systems studied, an increase in yield due to X-rays was statistically significant in two instances and was of borderline significance in a third instance. In the other five systems, the differences in yield were not significant. Impurities and added catalysts caused relatively large variations in the yield of TiC14 from the reaction. Although the catalysts employed were reported in the literature as positive catalysts for the reaction, most of them were negative catalysts for the highly pure system studied. With only one exception, each increase in the purity of the charge resulted in a decreased yield of TiCl4. The experimental results indicate that many substances catalyze the reaction studied and suggest that the differences in reactivity of the charge stocks may be due to their various contents of positive and negative catalysts.

Jan 1, 1962

By Herbert H. Einstein

Instability of rock slopes often occurs in the form of excessive movement of bodies that are bounded by discontinuities. The well known limit equilibrium analysis for wedges and blocks suffer, however, from procedural simplifications and from the basic deficiency of limit eguilibrium analysis--the rigid body assumption. Thus, stability analysis for 2-and 3-plane wedges with a wide range of additional features regarding failure modes and external forces have been developed. The deficiency, due to the rigid body assumption, was corrected by an approach that includes the effects or the in-situ stress field and of the stiffness of discontinuities. The final step in making limit equilibrium approaches more valid was achieved with the method of artificial supports which makes it possible to identify among all possible failure modes the critical one and to determine the corresponding factor of safety. The analytical development includes the creation of appropriate computer codes and routines for programmable pocket calculators.

Jan 1, 1979

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1982 (October 1, 1980 -September 30, 1981) under its Minerals Health and Safety Technology program. Contingencies may require that a significant port ion of the program be deferred into fiscal year 1983. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the systems technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

By L. C. IlsLey, J. W. Paul, E. J. Gleim

Flame safety lamps have been used in gaseous mines since the Davy lamp was introduced, more than 100 years ago. During the last decade the flame safety lamp has been rapidly replaced by the electric lamp as a device for illuminating the miner's working place; in the United States the electric cap lamp has been widely adopted. For example, in 1911 approximately 45,000 flame lamps and no electric lamps were being used in the Pennsylvania bituminous mines, which were then producing 35 per cent of all the soft coal mined in this country; by 1918 the flame lamps had decreased to 17,000, whereas electric lamps-mostly of one maketotaled nearly 48,000. In Great Britain during the same years the total of 723,934 flame lamps decreased to 590,185 and the electric lamps gained rapidly from 4,298 to 156,521. No later reliable figures are at hand. However, before the flame lamp becomes obsolete, it is fitting that the Bureau of Mines compile a permanent record of a device which has served the mining industry for more than three generations, and not only made possible the development of entire districts that otherwise could not have been worked but undoubtedly saved the lives of thousands of underground workers. Flame safety lamps are capable of doing more than the name indicates. First, under normal conditions, they can be used in a mine atmosphere that contains an explosive mixture of gas and air without great danger of exploding such a mixture, though such use of a flame lamp should not be permitted. Second, to an experienced man they indicate percentages of gas much lower than the explosive limit, and thus can be used to indicate to workers the approach of an unsafe condition in the mine atmosphere. Third, flame lamps will not burn in an atmosphere greatly deficient in oxygen, and they therefore warn the users of such deficiency in time to withdraw to a place of safety. Flame safety lamps are still used rather widely in the United States for general illumination and to a still greater extent for detecting gas. Many coal-producing States require fire bosses to use these lamps in gaseous mines, and the regulations of several States specify that a gIven number of such lamps be kept available for emergency service.

Jan 1, 1924

Watershed Jll in Jefferson County, Ohio we instrumented in 1977 as one of three watersheds established for the purpose of investigating surface mining and reclamation effects upon local hydrology, sediment discharge, and sediment and water quality. Each watershed was less than 50-acres in size, and was in a different geologic setting within southeastern Ohio. Surface runoff and ground¬water levels were monitored. Samples were taken for sediment determination and chemical analysis prior to mining. Monitoring and sampling continued through the period of watershed disturbance caused by mining and reclamation activities, which began in May 1980 at Watershed Jll. A psuedo-postreclamation period followed the initial cessation of man-machine activity on the watershed. A second reclamation effort occurred in the fall of 1981 and was to be followed by a third in 1982 after observations ceased. A true final postreclamation period was not monitored at this site, because the erosion control practice (terrace diversions) failed after each reclamation. Watershed Jll was a small pasture and wooded watershed with sandstone and shale above the mined coal seam prior to mining. A clay layer under the coal supported a perched saturated zone, termed the top aquifer for convenience. A lower underclay supported a second saturated zone called the middle aquifer. A lower perched aquifer had been dewatered by previous deep mining. After about three years of premine data and about two and one-half years of mining reclamation and psuedo-postreclamation data, the following general observations may be made: 1. The mining-reclamation phase was very short, and the postmining period was characterized by erosion failures and remedial disturbances that kept the watershed condition and size in a state of change. It was impossible to collect sufficient data to confidently characterize the hydrologic-sediment-chemical aspects of the mining period or of a postreclamation period and, most importantly, of the future watershed after its various properties and characteristics have ceased adjusting to its severe disturbance and reconstitution. 2. A seeding of wheat followed by grasses and legumes was not a particularly successful reclamation practice in terms of stabilizing the new soil. Numerous rills and small gullies developed in spite of installed diversions. 3. Storm runoff rates and yields at the watershed outlet increased from the premine, (phase 1) to the mining-reclamation (Phase 2) periods, and remained at or near the Phase 2 level through the postreclamation (Phase 3a) period. 4. The top aquifer changed in physical and chemical character as a result of mining and was becoming reestablished as the project drew to a close; but it is impossible to predict its final configuration or character. 5. Dewatering of the top aquifer resulted in a complete cessation of baseflow because the middle aquifer water table lay below the elevation of the watershed outlet. 6. The top and middle aquifers were merged in one area of the watershed where the upper coal underclay was disturbed. 7. Failure of the diversion terraces and their outlet obscured the effects of the reclamation practice upon sediment concentration and yields. There was little difference in sediment concentrations between Phases 2 and 3a. 8. Drinking water standards were met by surface waters throughout the period of observation except for two samples that exceeded the nitrate-N allowable level of 10 mg/l. 9. In all Phase 3 surface-water samples, iron concentrations were within the limits established by OSM, and manganese concentrations exceeded the regulation level only once. pH fell below the lower regulation level of 6.0 between 10% and 20% of the time. 10. The chemical quality of sediments was generally about the same after reclamation as before mining, with the exception of organic carbon, which decreased.

Jan 1, 1983

By William G. Pariseau

The research reported here concerns a four year study of the rock mechanics aspects of two underground hardrock mine study stopes. The first study was conducted at Anaconda Minerals Company's Carr Fork Mine near Tooele, Utah. The second study was conducted at the Homestake Mining Company's Homestake Mine In Lead, South Dakota. Both case studies were cooperative efforts of mining company personnel, the Spokane Research Center of the Bureau of Mines and the Department of Mining Engineering, University of Utah. Large diameter (6 1/2 In.) blastholes were an integral part of the stoplng method at each mine. A true vertical crater retreat (VCR) method was used at the Homestake Mine, while a vertical bench mining method (VBM) was used at the Carr Fork Mine. VCR and VBM methods were developed In the 1970's; they offer significant productivity gain and are now used throughout the world. The new technology, however, brings with It a requirement for more sophisticated engineering design and control. Since there are no personnel in a VCR or VBM stope, all ground control Including dimensioning of stopes and pillars and the layout of cable bolt assays or other artificial support must be done in advance of production blasting. Accordingly, the objective of the research study was the establishment of a procedure for optimizing stops and pillar sizes. The approach taken was In each case a combination of mine measurements of the study stope response to mining, laboratory testing for rock properties and In situ stress measurements of the premining stress field, and theoretical calculations of the study stope response to mining. All calculations were done with the UTAH-II finite element computer program. Simulation of the blasting sequence gave a correlation of 0.88 between measured and calculated extensometer readings (Incremental relative displacements) at the Carr Fork Mine where other 30 Instrumentation boreholes were used to monitor the test stope response. A correlation of 0.84 was obtained at the Homestake Mine where 19 instrumented boreholes were used for monitoring purposes. These high correlations validated the computer mode and calibrated It for rock mass properties. The calibrated model was then used In parametric studies of alternative design layouts.

Jan 1, 1985

By E. L. Singleton

The Bureau of Mines investigated extraction of aluminum from aluminum-silicon alloys as a means of utilizing domestic aluminum silicate ores for aluminum production. Aluminum was extracted from aluminum-silicon alloys by electrolysis in molten electrolytes of NaCl-KCI-AIC13 and NaCl-KCI-AIF3 in a laboratory-scale cell. Six alloys with aluminum contents ranging from 20 to 87 percent aluminum were tested, and aluminum products of primary grade or better were obtained. More than 80 percent of the aluminum was recovered with current efficiencies as high as 91 percent. Recovery of a metallurgical-grade silicon product from the anode residue by an acid leaching procedure was possible with the 50-50 and 65-35 Al-Si alloys.

Jan 1, 1972

By Robert E. Green

This Final Report summarizes the results of work accomplished under Contract No. J0215039. It is in an executive overview or executive summary format. The number and description of the various technical reports prepared and submitted is outlined. The essential changes and reasons for the revised program schedule/contract modifications actually enacted in May 1982 are discussed in detail. The evolving mines/deposits list and the accompanying criteria classifications are explained along with the verifications/justifications for adding or deleting specific mines/deposits to the list. Difficulties and problems experienced during the different phases of the project in conjunction with the ensuing remedies are highlighted. The final section of they report is devoted to presenting Davy McKee's suggestions for improvements to future MAS commodity studies. Appendix I is comprised of three of the evolving mines/deposits lists starting with the original RFP list and ending with the final completed list. Appendices II and Ill are tabulated summaries of property data including reserves/resources, assays, production, and operating costs. The figures for the specific mines/deposits are given in "range of values" so as to protect the confidentiality of the individual owners/ operators.

Jan 1, 1983

By Stephen A. Swan

This Bureau of Mines report discusses research to analyze and evaluate extended bumper systems in order to determine the degree of protection provided to equipment operators in the event of rear-end collisions be-tween off-road rear-dump haulage trucks. The basic characteristics of rear-end collisions were determined, and a detailed analysis of the col-lision dynamics was performed to identify the magnitude and direction of impact loads, the amount of energy that must be absorbed during impact, and the major factors that affect the outcome of a collision. Separate bumper designs were developed to facilitate attachment to four 170-st-capacity haulage truck frame types.

Jan 1, 1987

The above referenced contract between Badger Manufacturing Corporation and the U. S Bureau of Mines was executed June 30, 1975, as a result of the request for proposals for innovative machine concepts. We selected the cutting machine category because of the obvious lack of technical progress in this field for many years: Phase I of the contract required blasting fragmentation tests to determine proper blasting patterns for use with the auger-type kerf cutting machine. Phase II required design concept development for a machine capable of cutting a circular void as an aid to blasting.

Jan 1, 1975

By M. Hertzberg

Results of a comprehensive study of the absolute spectral radiance of the infrared emissions from methane-air explosions are reported. The spectral growth of these expanding flames were recorded with a time resolution of 1 msec in the spectral range of 1.7 to 5.0 µm. Time-resolved spectra were obtained for methane-air mixtures as a function of stoichiometry, nitrogen dilution, and Halon dilution, in a 9-liter vessel under different venting conditions. Data are also presented for coal dust-air explosions. Temperatures, obtained from the absolute radiances and from a band ratio technique for methane-air, are internally consistent and are generally 50° to 200°K below adiabatic flame temperatures. All near limit mixtures gave essentially the same flame temperatures (1,500° to 1,600° K) regardless of whether the limit was obtained by dilution with excess air, excess methane, excess nitrogen, or Halon. The coal dust explosion spectrum is essentially a blackbody continuum at 1,500° K with some selective emission at 4.4 µm from hotter CO2. The data are analyzed in terms of the radiative dynamics of a sperically expanding flame zone. The importance of radiative transport is assessed. An equation is derived which relates the instantaneous fraction of combustion power radiated to adiabatic variables.

Jan 1, 1973

This report is a compilation of all information obtained in accordance with the requirements of contracts SO122076 and H0232056. A series of eight coal mines were visited to determine their communications usage and requirements. Presently available equipment was surveyed and evaluated to determine its applicability to the needs of the mines. The equipment studied includes that made by the following companies : Anaconda Telecommunications Division Andrew Antenna Bendix Communications Division Collins Radio Group of Rockwell International Executone Communication and Sound Systems Gau-tronics Mine Safety Appliances Company Motorola Communications and Electronics, Inc National Mine Service Company Plessey Communications Systems Corp Pye Electronics Limited Reach Electronics Set Com Corporation Sonex Incorporated Mine visits and in-depth interviews were made alt the following sites: Robena No. 4, Pennsylvania Greenwich Colliery Mines, Pennsylvania Somerset Coal Mine, Colorado Keystone No. 1, West Virginia Harris Mine No. 1, West Virginia Baldwin Underground No. 1 Mine, Illinois Lovilia No. 4 Coal Mine, Iowa Orient No. 3 Coal Mine, Illinois

Nov 15, 1974