Search Documents

By David D. Rabb

A report on location, sampling, assays, mineral examination, amenability leach tests, and evaluation of certain mine dumps in Mohave County, Arizona. Extractions of greater than 30 percent of the gold and silver were achieved during simulated heap leaching of selected mine dump material. Consumption of reagents was relatively low and results suggest leaching of prepared heaps is technically viable and could be economically attractive.

Jan 1, 1980

By Irvin Pritts

This report describes the design, fabrication, and testing of a prototype instrument which demonstrates the feasibility of determining respirable coal dust concentrations by light reflectance photometry. Coal dust is collected on a filter and the quantity collected is continuously monitored by reflectance-photometry. Light emission and detection is accomplished by reflective object sensors, which have both light source and detector in one chip. The use of a pulsed light source insures low drift characteristics of the measuring circuitry. The collection of the respirable coal dust on filters facilitates accurate calibration and also allows measurement verification, if desired, by well-accepted, gravimetric methods.

Jan 1, 1981

Large quantities of combustible materials are often found in underground metal and nonmetal mines, with support timber most often the predominant combustible material. Oils, lubricants, paper, cartons, and rags are additional combustible materials and are commonly found in maintenance shop areas. Welding and cuting, shorted or overloaded electrical cables, spontaneous combustion, and careless smoking are some of the common fire ignition sources. Inexpensive, reliable fire detection and suppression systems are available to provide early warning of such fires and to isolate and extinguish fires that originate in underground maintenance shop areas. Technology developed and demonstrated under Bureau of Mines Contract H024216, Mine Shaft Fire and Smoke Protection System, may be applied to protect underground maintenance shop areas. The mine area described in this report is a representative ex-ample only; the fire protection system described considers costs, benefits, equipment performance and includes the concepts of: ? Early warning and alarm ? Isolation ? Extinguishment ? Control. Each fire protection system application requires analysis of numerous variables including total mine profile (depth, personnel, escape routes, hazards, etc.).

Jan 1, 2011

By Thomas E. Doerfler

Information and data related to the occurrence of fatalities due to major disasters in metal/nonmetal underground mines were analyzed. Standard statistical methods were used to estimate the probability of occurrence of major disasters, and to examine the relationship of disasters to injury statistics published annually.

Jan 1, 1980

By R. O. Dannenberg

The Bureau of Mines conducted laboratory batch and small-scale continuous tests to remove traces of dissolved molybdenum from water simulating waste discharged from a molybdenum concentrator, Molybdenum concentrations, initially ranging from 2 to 10 ppm, were decreased to 0.5 ppm or less by coprecipitation of the molybdenum with freshly precipitated ferric hydroxide" The precipitate was separated as a froth by dissolved-air flotation for subsequent disposal. Although the treated water met current environmental standards for contained molybdenum, contained particulate iron might have to be removed by filtration for the water to be acceptable. Estimated costs for treating concentrator effluent water were 55 cents, 57 cents, and 64 cents per 1,000 gal at initial molybdenum concentrations of 2, 4, and 10 ppm, respectively.

Jan 1, 1982

By Thomas Novak, Robert Goldstein

The analysis of a machine-luminaire configuration is a time- consuming process requiring the construction of a machine mockup, installation of a designated lighting arrangement, and an extensive set of illumination measurements. This entire process, however, is well suited to computer analysis. By simulating the machine geometry and the characteristics of the desired luminaires, the incident light levels can be calculated at the required set of points. This Bureau of Mines paper presents a general description of the techniques involved in performing this simulation.

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By Dipak Sengupta

This study analyzes the safety, technology, and economic impact of eliminating safety fuse from metal/nonmetal mines, based on operation and manufacturer experience over the past five to ten years. If safety fuse is eliminated, blasting accidents will decrease with no technical impact except for some limited, specific applications. The economic impact will be minor for large operations, but will be significant enough for small operations that some small operations will likely close rather than change. The majority of the mines would probably change over, with the extra cost absorbed by the market. Elimination of safety fuse would have obvious impact on the two manufacturers of safety fuse; one manufacturer already produces an alternative system, and will remain unaffected; the other will be affected if they do not change their production strategy. There will be a very minor effect on the mining industry as a whole due to abolishment of safety fuse from the standpoint of employment or production.

Jan 1, 1980

By Steven W. Schmauch

A mineral survey by the U.S. Bureau of Mines and U.S. Geological Survey indicate the Blanco Mountain RARE II area has low potential. Lode deposits consist of small, mineralized quartz or quartz-gossan veins. The veins are sparse and widely separated and lead, silver and gold content is restricted in amount and concentration. No gold or other potentially economic minerals were found in a placer deposit. There is no evidence of industrial mineral, geothermal, or energy resource potential in the study area. INTRODUCTION A mineral resource survey of the Blanco Mountain RARE II area (No. 5059), Inyo and Mono Counties, California was conducted in July 1981. This report summarizes the results and interpretations of the Bureau of Mines investigation.

Jan 1, 1982

By Paul H. Lu

This Bureau of Mines report summarizes the analysis and eveluation of the field measurement results of a comprehensive ground control study conducted in a mechanized longwall coal mine in West Virginia. Emphasis is placed on the three basic ground control parameters: ground pressure, ground movement, and geomechanical properties. Specific topics include premining ground pressures, front-abutment pressure in the longwall panel, histories of pillar loading, differential roof-strata movement and bed separation, differential floor strata movement, entry roof-to-floor convergence, in situ moduli of rigidity of coal seam and roof and floor strata, and mechanical properties of coal and coal measures rocks.

Jan 1, 1985

By Terry J. Close

The Welcome Creek Wilderness has small, dispersed gold placers. Pockets in the 25.5 million yd3 (19.5 million m3) of alluvium along Welcome and Rock Creeks have as much as $5.61 gold/yd3 ($7.34/m3) at $500/troy oz ($16.08/g). All the alluvium averages 20.1 cents gold/yd3 (26.3 cents/m3). Because of the low average gold content large-scale placer mining would not be economically feasible. Small-scale selective pocket mining, however, may be profitable. The alluvium along the streams in the Wilderness has little apparent potential for production of sand, gravel, or stone because alternate sources are closer to markets. The four lode prospects known within the Wilderness appear to have low mineral potential. No oil, gas, uranium, or geothermal energy sources are known to be present.

Jan 1, 1982

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

By Ferron A. Olson

Natural bornite (Cu5FeS4) leached in ferric chloride or in sulfuric or hydrochloric acid solutions with oxygen showed several differences. In ferric chloride 80 of the copper was leached in two stages. The first (30 copper removal) requiring one minute was controlled by mixed kinetics (liquid ferric ion diffusion and chemical surface reaction). The second was controlled by formation of a surface sulfur layer and then diffusion through the sulfur. With oxygen in sulfuric acid reaction was slow and only the first stage was studied. Copper removal had an induction period. The bornite structure disappeared at 12% copper removal (also found with ferric chloride) and covellite formed on the surface with a species inside the particles having an x-ray structure similar to CuFeS2 but with composition Cu3FeS4 (also with ferric chloride). Copper removal was controlled by iron dissolution. Surface iron vacancies filled with Cu+ to give CuS while interior copper dissolution produced Cu3FeS4. Preliminary results with oxygen and hydrochloric acid showed 80% copper removal and sulfur as end products (similar to ferric chloride).

Jan 1, 1982

By Frank G. Horino

Drill cores from 18 exploratory holes that were drilled into the unleached saline beds were tested for mechanical properties by the Bureau of Mines. Test cores were primarily selected from zones L4B, R4B, L3, and R3A in the Piceance Creek Basin, Rio Blanco County, Colo. Regression analysis techniques were tried in an attempt to relate kerogen yield or apparent specific gravity to the parameters compressive strength, Young's modulus, and Poisson's ratio. Correlation coefficients were very poor, indicating that this type of analysis was not amenable to these data. Analysis of variance techniques were tried using a division of either greater than or less than 10% nahcolite together with the requirement of less than 3% dawsonite. Results showed that a larger percentage of nahcolite tended to lower the compressive strength and to increase Young's modulus. A second analysis was made using a division of less than 3% dawsonite and greater than 3% dawsonite together with the requirement of less than 1% nahcolite. For this analysis, a larger per-centage of dawsonite tended to increase compressive strength, Young's modulus, and Poisson's ratio. Mean compressive strength values were determined for the mining horizons of interest. Average physical properties for design purposes were also determined for the horizons of interest and for a proposed adit based only on logged geologic depths to these horizons. No consideration was given to percentages of nahcolite and dawsonite. Creep data obtained from nahcolite-and dawsonite-rich oil shales provides a best fit to a modified power equation.

Jan 1, 1978

By T. C. Woo

This report describes the program that studied the theoretical and practical aspects of the belt cleaning systems, investigated-the possibilities of a self-replacing and/or sell-adjusting belt cleaning device, and designed a horizonal pentagonal turret setup for the underground mine belt conveyors. This design resulted from comprehensive literature survey (both academic and commercial), actual mine visits, study of the mechanics of belt cleaning and bench-type experiments. It has complete working drawings and rough cost estimates.

Jan 1, 1977

By M. John Brodie

This report reviews the regulatory environment as it pertains to waste rock management and disposal from mining operations, excluding coal and placer gold operations, in the \irate of Alaska. It is based on the EPA's staff position on an effective program to regulate mining waste as presented in the May, 1990 Strawman II document. The unique conditions which occur in pans of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a waste rock facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection, are examined.

Jan 1, 1992

By Warren E. Morrison

INCREASED production and utilization of minerals fuels and power accompanied the overall expansion in U.S. economic activity during 1963, which saw continued advances toward higher production, employment, and purchasing power. During 1963, record levels of wages, profits, and consumption were attained, while costs and prices maintained the stability exhibited throughout most of the recovery period. Expanding industrial production, the average index of which went from 118.3 in 1962 to 124.3 in 1963, narrowed the gap of unused manufacturing capacity to an estimated 5 percent. Gross national product (GNP), another major indicator of economic activity, reached a record level of $583.9 million (current dollars) during the year, this being $27.7 billion, or 4.9 percent above 1962. These achievements were somewhat marred by unemployment, which remained at 5.5 percent of the labor force in 1963, and the continued deficit in the U.S. balance of payments. Against this general background, total national consumption of energy resources for the year was equivalent to 49,816 trillion British thermal units (Btu), an increase of 4.2 percent over 1962. This represented a somewhat lower rate of growth than for GNP during the year.

Jan 1, 1964

By Holt L. Farley

This report describes the development of an electronic system which detects unsafe slack and overload conditions in underground mine hoist ropes. The Slack and Overload Rope Protection System (SORPS) includes a fail-safe load cell inserted between the rope and the conveyance, and an accelerometer mounted on the conveyance. Signals from these transducers are telemetered via a radio link to the hoist control room, where they are combined with drum speed and chair status in a microprocessor-based decision and display unit. Abnormally high external force levels are detected as discrepancies between rope tension and cage acceleration; conveyance weight is inferred continuously. Hazardous conditions are displayed to the hoist operator, along with general hoist status. The system has been tested in a working mine for approximately two years. The report contains specifications, design data and field test experience generated under the SORPS program. It also includes information on dynamic modeling, vibration environment, the status of existing slack detection systems, and applicable control strategies.

Jan 1, 1983