Search Documents

By Lars G. Olavson

A prototype roof bolt which can be remotely placed by pumping has been developed by the Bureau of Mines. It is known as the "Pumpable Bolt". With the objective of field testing the effectiveness of the pumpable Bolt roof support system a mining machine was developed capable of installing Pumpable Bolts in the normal production cycle of a typical underground coal mine. The machine was built and the pumpable Bolt concept tested and evaluated as a total system in shop and mine tests. The machine was operated in the mining cycle of two mines and pumpable Bolts were installed at both mine sites.

Jan 1, 1976

By Wilbur I. Duvall

This report presents experimental data on crater formation in four rock types. From an analysis of these data a general theory of rock breakage by explosives is deduced. This theory accounts for most of the rock breakage and other phenomena that occur when a concentrated charge is detonated in a drill hole near a free surface. From instrumented crater tests and high-speed motion pictures of the explosions, various experimental checks on the deduced theory of rock breakage are made. The general mechanism of rock breakage by explosives as described in this report is outlined briefly below. The detonation of the explosive charge creates a high gas pressure in the charge hole, which in turn generates a compressive strain pulse in the surrounding rock. This compressive strain pulse travels outward in all directions from the charge hole. Near the charge hole the amplitude of this strain pulse is sufficient to cause crushing of the rock. However, as the strain pulse travels outward its amplitude decays rapidly until no further crushing of the rock is possible. The compressive strain pulse continues to travel outward until it is reflected by a free surface. Upon reflection the compressive strain pulse becomes a tensile strain pulse. As the strength of rock in tension is much less than in compression, the reflected tensile strain pulse is able to break the rock in tension, progressing from the free surface back toward the shot point. In other words, the rock is pulled apart, not pushed apart.

Jan 1, 1957

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

BIBLIOGRAPHY 1. Dougherty, John J. , "Control of Mine Fires", Publication of the Mining Extension Service, School of Mines, Appalachian Center, West Virginia University (1969). 2. Coal Age, "Fire, Explosions and Recovery, Federal No. 1 Mine", November, 1963. 3. Nagy, et al., "Sealing a Coal Mine Passage through a -Nor-ii-hole: A Progress Report", U.S. B. M. Publication No. 6453, (1964). 4. Murphy, et al., "Use of Fly Ash for Remote Filling of Underground Cavities and Passageways", U.S. B. M. Publication No. 7214, (1968). 5. Pennsylvania Drilling Company, Pittsburgh, Pennsylvania. Personal Review of Equipment. 6. Industrial Hazards and Communication, Division of U. S. B. M. Personal Communication with John Murphy and Merle Bowser. 7. Instrument Technology, Inc., Borescopes and CCTV Systems for Inspections of Nuclear Reactors; Personal Communication. 8. "Public Works", July, 1972. 9. The Industrial Hazards and Communications Division of the U.S. B. M. , Personal Communication regarding Cohu Model No. 2006. 10. "Bibliography on Underwater Photography and Photogrammetry", Eastman Kodak Pamphlet No. P-124. 11. Optical Properties and Visual Effects of Smoke-Stack Plumes, U.S. Department of HEW, 1967. 12. Middleton, W. E. K. , "Vision Thru the Atmosphere", Univ. of Toronto Press, 1952. 13. Kodak "High Speed Infra Red" film and Singer Corporation Model TI Silicon Vidicon TV Camera. 14. Night Vision Laboratory, Fort Belvoir, Maryland; Barnes Engineering Company, Stamford, Connecticut, Model, T-101; AGA Inc. , Secaucus, New Jersey, Model, "Thermovision" 680.

Jan 1, 1973

The Leuna Factory of the I. G. Farbenindustrie A. G., situated near Merseburg, is the biggest heavy-chemical plant in Germany and produces a very wide range of products, mainly based on hydrogen or hydrogen and carbon monoxide. Its principal products are ammonia, synthetic petrol derived from the hydrogenation of brown coal, and synthetic alcohols made from hydrogen and carbon monoxide. The plant was first, visited on April 21, 1945, by a team including E. Cotton, V. Haensel, E. B. Peck, P. K. Kuhne, H. M. Weir, L. L. Hirst, W. W. Odell, G. U. Hopton, H. Hollings, J. F. Ellis, and H. G. Simpson. It was again visited on May 8-24, 1945, by a combined British and American team consisting of R, Holroyd, M. A. G, Banks, D. A. Howes, A. J. V. Underwood, R. A. Taylor, W. F. Faragher, H. Schindler, and J. G. Allen. This team was later joined by J. F. Ellis and R. J. Morley. A third visit with particular reference to catalyst manufacture was made by W. F. Faragher and W. A. Horne, and the notes of these latest investigators have been taken into account in preparing the report. This report was edited by Dr. R. Holroyd.

Jan 1, 1946

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972

By Alfred Petrick

This study gives an analysis of the copper system byproducts and discusses the identification and classification of byproduct metals and their supply systems. Arsenic, platinum-group metals, silver, gold, selenium, tellurium, molybdenum, rhenium, uranium, aluminum, magnesium, and byproduct copper, lead, and zinc from complex ores are covered. The report describes several metallurgical systems, the marginal and incremental products costs of byproduct subsystems, industry structure and organization, and the historical data on price, consumption, and supply. Supply curves are presented for about one-half of the byproduct metals studied. The study develops a conceptual framework for analysis by reviewing the present concepts of byproduct supply and the related price theory. It gives the sources of supply of the individual byproduct metals to indicate the importance of the byproduct supply to the total supply. Mills, smelters, and refineries processing byproduct materials for their metal content are identified by geographic location and company ownership, The study also includes information on the reserves-resource base supporting byproduct output, reserve estimates, and the demand aspects of each byproduct metal.

Jan 1, 1973

The investigation summarized in this report addressed two primary issues: the determination and use of correction factors, and the development of guidelines for velocity measurement site selection. Other ancillary issues which were addressed include a comparison of measurement methods and devices, aircourse cross-sectional area measurement, and characteristics of mine airways. An exhaustive literature search and analysis was performed; extensive in-mine experiments were conducted; a quantitative analysis of the data was used to develop correction factor tables and site selection guidelines. The reported results of other researchers who have examined the correction factors and site selection criteria, were analyzed in light of the results of this study. The measurement devices included in the experimental phase were: vane anemometer, vortex shedding anemometer, a prototype thermoanemometer, smoke tube, and, oil of wintergreen. The measurement methods include single-point centerline, timed¬-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices.

Jan 1, 1983

By Roy T. Sorensen

As part of its mission to maintain an adequate supply of minerals to meet national needs and maximize mineral production from domestic sources, the Bureau of Mines is investigating the recovery of alumina by hydrochloric acid leaching of kaolinitic clay. Most iron impurities are leached from the clay along with the alumina and must be removed before or during crystallization to aluminum chloride hexahydrate. The thermal decomposition step then provides an alumina product of acceptable iron analysis. Miniplant studies of a Bureau-developed solvent extraction technique, using a tertiary amine in kerosene diluent, have demonstrated that the iron content in aluminum chloride leach liquors can be reduced to levels of less than 0.007 wt-pct (7 ppm), expressed as Fe203. Entrained and dissolved organic matter in the purified pregnant leach liquor from the solvent extraction circuit can be reduced to less than 2 ppm by using a fabric-packed coalescer and subsequent activated carbon treatment. Investigators discovered that a steady buildup of zinc accumulated in the solvent phase within the extraction circuit, proportional to the amount of leach liquor treated. The solvent phase zinc analysis increased by 0.01 wt-pct ZnO for each 1,000 gal of pregnant leach liquor purified.

Jan 1, 1981

By Gerald H. Groenewold

Reclamation of surface-mined landscapes is commonly defined only in terms of biological productivity. Other critical concerns associated with surface mining include the long-term quality of groundwater and stability of the postmining landscape. Meaningful reclamation design must address all these concerns. Reconnaissance of postmining landscapes indicates that three types of instability occur in these settings. These include: area-wide settling, localized collapse, and piping. Area-wide settling is most pronounced during the first year after contouring but appears in precontouring valley areas where frozen materials are contoured with a dozer. Although severe in some settings, development typically ends within one year. Piping appears to be a severe and long-term problem in some settings. Piping usually begins soon after contouring ceases and may continue for several years. In some postmining landscapes, piping has only started to develop after as many as five years of apparent stability. Piping is controlled by a combination of physical and chemical conditions in the spoil. A key factor is the presence of highly dispersive materials in the near surface. The design of a stable postmining landscape requires the integration of severe critical factors. These include: 1) detailed knowledge of the distribution of overburden materials with emphasis upon the delineation of highly sodic sediments; 2) proper equipment selection; and 3) a consideration of climatic factors. For reclamation to be successful, it must consider the entire landscape, not merely the soil zone. Any approach short of this will lead, at best, to temporary solutions.

Jan 1, 1980

By P. Nicholls

Patent records show that the idea that the burning of fuels can be improved by mixing or pretreating them with chemicals 6 dates back to the early years of the last century. By 1845, English and French patents included the specific beneficiations of elimination or reduction of smoke, soot, and clinker; reduction of the ashes, presumably meaning the total weight of refuse from the ashpit; elimination of sulphur fumes; increase in the rate of burning; increase in the time a given charge of fuel would last; and, in most patents, a saving of fuel. The earlier patents specified additions up to 80 pounds or more per ton of fuel, but after 1860 the quantity was rarely more than 4 pounds. There is no record of the extent to which these patents were commercialized, but after 1884 many American patents were assigned to companies specializing in treatment of coal, so it is probable that the products were marketed on a considerable scale at least as early as that date. From 1900 on, many companies marketed proprietary products that were sold under the general name of "fuel savers." Since its establishment in 1910, the Bureau of Mines has continually received inquiries about these products and, at the request of other govern-mental departments, has tested some used in accordance with the instructions of the purveyors; the results were all negative and, within the accuracy of measurements, the products had no effect on the burning.

Jan 1, 1937

By Alla D. Mah

The heat of formation of scandium sesquioxide (Sc203) has not been measured previously, and existing values for gallium sesquioxide (Ga203) are subject to large uncertainties. As a consequence, thermodynamic calculations involving these oxides hare lacked scientific exactness. This paper reports newly determined values of the heats of formation of gallium and scandium sesquioxides at 298.15° K., by combustion calorimetry. The corresponding free energies of formation are derived from heat and entropy data.

Jan 1, 1962

By R. Stefanko

This study concerns itself with the effects of diesel exhaust on mine ventilation systems. The approach here consisted of the development of mathematical models for emissions, dilution, and dispersion of gaseous pollutants from diesels. The general scheme was to use partial differential equations to predict concentration growths. Specifically, the following situations were modeled: 1. A single stationary diesel engine working in a single roadway. 2. A single diesel engine moving with uniform velocity in a single roadway. 3. Multiple diesel engines moving continuously in a cycle in a roadway with appreciable leakage. 4 Multiple diesel engines moving continuously in a cycle in a roadway with little or no leakage. 5. Multiple diesel engines moving randomly in a roadway with uniform air velocity.

Jan 1, 1974

To predict the spontaneous combustion potential of bituminous coals using a simple expression based on an easily acquired coal property. Background Approximately 20% of underground coal mine fires in the United States since 1978 have been attributed to spontaneous combustion. Spontaneous combustion fires in underground mines are most likely to occur in gob area; and are difficult to detect and to extinguish by direct fire fighting methods. Often, sections of the mine or the entire mine must be sealed for long periods, at a great economic loss to the mine operator, mine employees, and the surrounding community. It is conservatively estimated that the cost of scaling a large mine is about $50 million.

Jan 1, 1989

This Bureau of Mines publication contains the texts of the four papers presented at the May 6-7, 1980, seminar on the role of overburden analysis in surface mining. Coverage includes the geologic distribution of pyrite and calcareous material and its relationship to overburden sampling, overburden sampling and analysis, use of soil-overburden data in mine planning and development, and minesoil classification.

Jan 1, 1981

By F. D. DeVaney

Manganese-bearing deposits f the Leadville, Colo., district are of two distinct types. Manganosiderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 900 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 18.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By M. E. Tyrrell

Lightweight basic refractories suitable for use in some sections of the all-basic furnace were developed. Potential advantages of such refractories are lower weight, improved resistance to thermal shock, and less tendency to spall off the working face. Plant trials in positions not subject to heavy loading or severe erosion seem warranted. Forsterite (2MgO.SiO2), stabilized dolomite (2Ca0?SiO2 + MgO), and chrome-spinel [(Fe,Mg)0?(Cr,Al) 031 refractories were fabricated using bubbles as the principal component in the brick mixtures. Bubbles were blown from melts of the basic raw materials as they were tapped from a conducting-hearth arc-resistance furnace. The bubbles were graded, bonded with synthetic Forsterite plus mineralizers, dry-pressed, and fired to temperatures of 1,600° C. or over in a gas-fired kiln. Refractory properties of the bubble brick were compared with those of insulating refractories made by burning combustibles out or dense brick mixtures. Lightweight refractories fabricated of bubbles were one-third lighter in weight than dense bricks of like materials. Their mechanical strength was satisfactory, and their resistance to thermal shock was excellent. In tolerance to open-hearth slag and in resistance to thermal shock, the chrome-spinel bubble bricks wore the best of the refractories tested. Basic refractories of the insulating type were about 40 percent lighter in weight than dense commercial refractories, but they were mechanically weak and not suitable for superduty service.

Jan 1, 1962

By A. U. Christensen

THERMODYNAMIC data for many of the common interoxidic compounds are seriously lacking, and appraisal of possible ceramic or metallurgical applications depends upon dubious estimates. In particular, high-temperature heat-content estimates may be invalid because of unknown phase-transformations. This paper reports experimental heat-content values above 298.15° K. for five interoxidic compounds-the aluminates of lithium and sodium (LiAlO2 and NaAlO2), the ferrites of lithium and sodium (LiFeO2 and NaFeO2), and lithium titanate (Li2TiO3), as obtained by the Bureau of Mines. Sodium aluminate, sodium ferrite, and lithium titanate were found to have previously unknown transformations in the crystalline state. The heats and temperatures of these transformations were evaluated as were also the heats and temperatures of fusion of sodium ferrite and lithium titanate. The heat-content results are assembled in both tabular and algebraic-equation form for use in conducting thermodynamic calculations at temperatures in the range 298°-2,000° K.

Jan 1, 1960

By Clifford H. Summers

This report describes an experimental program which we conducted on behalf of the U. S. Bureau of Mines, to select from currently available materials two novel systems of construction for air-restraining bulkheads to be used in control of radon-polluted air in underground uranium mines. The program included both laboratory and field tests, the latter conducted in a portion of an operating mine owned and operated by Union Carbide Corporation at LaSal, Utah. The test site was a worked-out, double entry stope having a Volume of about 2000 cubic meters, and was located immediately adjacent to an exhaust airway. The bulkheads were constructed of 15 cm x 1.5 cm timber uprights, 5 cm x 15 cm horizontal members supporting a close-fitted 13 mm plywood curtain-wall., which was covered with a low-permeability membrane to seal in the radon-polluted air. The two membrane materials selected for testing were chosen from a list of twenty-two potentially acceptable candidates using criteria such as strength, flammability, ease of application, adhesion, radon permeability, and elasticity. Thirteen of the candidates were tested in our laboratories for adhesion to plywood and to both wet and dry concrete (simulating wet and dry mine rock surfaces), and for their general physical properties, including radon permeability. The final selections made by the Technical Project Officer, and based on our recommendation, were a pre-formed ethylene propylene diene monomeric rubber (EPDM) membrane 1.12 mm thick, normally used as a roof sealant in industrial construction, and available from Carlisle Tire and Rubber Co., Division of Carlisle Corp., Carlisle, PA, and Aquafas 48-00, a water-based mastic used in a wide variety of commercial applications and available from H. B. Fuller Co., Foster Products Division, Spring House, PA. The EPDM membrane was applied as a single sheet, laminated (dry) between two layers of plywood, and the Aquafas was applied both by troweling and spraying onto a plywood surface. In the field test, radon concentrations were continuously measured before, after, and in the trapped air behind each bulkhead. Temperature, pressure, and velocity of the air in the adjacent airway were also measured and recorded continuously. Radon fluxes at the rock/air interface and through the bulkheads themselves were measured manually on a frequent basis. All continuously acquired raw data were recorded automatically on two USBM Data Aquisition Systems (DAS), and the raw data were converted into engineering units and recorded on magnetic disks by a specially programmed microcomputer that was interfaced with the DAS's. Relatively clean (i.e. low radon concentration) air was pumped into a point near the face of one test bulkhead from a location 170 meters away through vent bag. Several air curtains and two air-restraining bulkheads were erected in passageways adjacent to the test area in an effort to control both velocity and radon concentration of the air flowing past the bulkhead faces. An average concentration of approximately 500 pCi/liter at a flow of 550 m3/minute was attained as the background concentration against which leakage through the bulkheads was measured. The entire field test period extended from October, 1981 to March, 1982, a total of six months, and was subdivided into seven successive time periods: 1) site preparation 2) background measurements prior to bulkhead construction 3) passive restraint, with bulkheads in place and totally sealed 4) open bleeder period of natural convection ventilation in and out of the bulkheaded area through a 10 cm (diameter) opening, with connecting tubing; leading into an Exhaust airway 5) open bleeder period, having forced exhaust through a 1.0 cm opening using a servo-controlled fan 6) charcoal trapping period, using the servo-controlled fan to exhaust air through the charcoal traps, to test the effectiveness of such traps in removal of radon from the exhausted air 7) site decommissioning Each of the two systems tested, one incorporating the pro-formed EPDM-rubber membrane and the other utilizing Aquafas 48-00, was assessed for effectiveness in controlling radon-polluted air by observing the change in the radon concentration in the ventilation air flowing continuously over the surface of each bulkhead. The sensitivity of the observed measurements was limited by the volume flow-rate of the ventilation air and the radon concentration in that air. The data would indicate that the observed increments in radon concentration in the ventilation air moving across bulkheads B-l and B-2 were essentially zero within the limits of sensitivity of the measurements. Data from radon flux measurement taken both on the sealed ribs adjacent to the bulkheads and on the bulkheads themselves did not differ significantly from blank data.

Jan 1, 1982

By Steven W. Schmauch

The U.S. Bureau of Hines conducted e mineral resource survey of approximately 232,000 acres in part of the Humboldt National Forest, Nevada, during 1989. About 7S percent of the study area was covered with mining claims. About 1,800 samples were collected end analyzed for 16 elements. Geologic structure, including thrust faults, is the most important factor in the localization of mineral deposits in the study area. The Independence mine (formerly Jerritt Canyon), Big Springs, and Wood Gulch are the most well known active properties, all developed on large, low-grade, disseminated gold deposits. These deposits have produced almost 3 million ounces of gold and are known to contain more than 8 million ounces of gold. At least 10 barite deposits in the south end of the range have had significant past production and contain 0.2 million tons of resources. Numerous precious and base metal targets have been identified and in some cases quantified during this study.

Jan 1, 1992