Search Documents

By Ankit Jha, Sudarshan Rajagopal, Purushotham Tukkaraja

Geologic structures are one of the crucial parameters in blast design. Structural geology and rock properties influence drilling patterns, blast layout, and initiation systems. A comprehensive understanding of structural characteristics is essential to achieve the desired blasting objectives. This paper aims to identify geologic features in a bench using images obtained from the drone. Images obtained from mine site are annotated for geological features such as faults and joints. Semantic segmentation of images is achieved using an encoder and decoder structure available in the machine-learning pipeline. The encoder consists of initial convolution and pooling layers to capture essential features of the geology and rock patterns from two-dimensional RGB images. Batch normalization is used to put all the features on the same scale. These images are then inputted as training data for the machine-learning algorithm. Machine learning model is trained on sub-section of interest to achieve reasonable accuracy. Initially, 1000 best annotations were used to train the model and additional samples were added later to achieve more accuracy and avoid iteration of machine learning model in wrong convergence. After the model achieves reasonable accuracy, it is used to recognize geological features on new data. Geological features identified on the new data can be used by the blasting crew in blast design and keeps the geological maps updated that can help the geotechnical team.

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008

By Jack Eloranta

"Unwanted, dynamic interaction of adjacent blastholes is a well-recognized phenomenon. Timingschemes and products are selected to minimize adverse effects. Large diameter, surface blasting is less prone to dead pressing and other disruptions which commonly plague underground and construction blasters. However, several lines of evidence suggest that fragmentation may be compromised as a result of powder column disruption in large diameter shooting as well."

Jan 1, 2016

By Frank Lucca

This paper includes research and investigation into blast design and blast optimization for vibration control in municipal and tight blasting situations, where specifications were extremely stringent. The paper is written for the field blaster to understand and develop blast plans based on field conditions. The paper includes blast design considerations, utilizing seismograph arrays to check and predict vibration results, and problems encountered in vibration monitoring in extremely tight situations (0-20 feet). Blast vibration frequency, acceleration, peak particle velocities, and relative displacement are discussed with effects in the near and far fields and blast designs utilized to stay under limits. The paper also discusses using the latest in technology for blast design to control vibration. Equipment includes 2D and 3D laser profiling systems, digital video, fragmentation analysis, seismograph arrays, and borehole tracking devices. Other topics are discussed such as public relations, working with regulatory personnel, unions, and other project consultants, and the problems associated with municipal blasting situations, such as, flyrock and proximity of other personnel and equipment on the project.

Jan 1, 2004

By Miquel Lamadrid, Changshow Sun, Chris Johnson

To reduce blasting overbreak and improve stope stability, several new blast designs were proposed for current and future stopes. Based on the analysis of the powder factor, and the extent of damage zone, the appropriate new blast design was selected. Excellent results were achieved from the new blast design. Comparing the new blast design with the old one, the largest of the overbreaks decreased more tan two times and average overbreak reduced more than two times. The new blast design is currently applied in all mining zones in Leeville underground mine.

Jan 1, 2008

By P. E. Hoffman, Joshua Ph. D.

The Institute of Makers of Explosives (IME) led a post-detonation debris collection project in conjunction with a large AN railcar detonation conducted by the Department of Homeland SecurityTransportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in the IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk) Quantitative Risk Assessment (QRA) tool. The test also provided valuable data about AN detonation characteristics when it is driven to detonation. The test took place at the Utah Dugway Proving Grounds (DPG) on April 27, 2018 and the debris collection was conducted the following two weeks with an average of 20 persons per day and an approximate total of 1,400 manhours. This paper details the collection efforts, challenges, and lessons learned. It also presents some of the initial findings relating to the debris distribution.

Jan 1, 2019

By Jhon J. Silva Castro

Blast vibration records used in mining contain unwanted information in the form of noise due to long-period drifts, background noise, and noise due to the conversion of the analogue signal to a digital signal. When recorded signals from blasting are used to find other physical variables, such as going from particle velocity to acceleration or displacement, the additional information in the vibration signal can result in inaccuracies in the estimation of the peak values and more dramatically, the results in displacement or acceleration can be nonzero near the end of the record. There are different proposed methods to clean or filter the unwanted information from the signal. All of the methods are based on finding the best fit of the record average value (baseline) and then subtracting from the record under analysis to produce the desirable adjustment. Different criteria and functions are used to define the best fit. The function to use will depend on the shape of the record average values. The main characteristic of the baseline function is that it represents a low frequency wave. Such a low frequency wave can be a periodic function or a polynomial expression of nth order. According to the order of the polynomial expression, the baseline correction can be linear, parabolic or high order. In this document the detailed procedure and the results for the baseline correction of a blast vibration record using a periodic function and a polynomial expression of different order is presented. The results show that the drift problem when displacement is calculate using velocity records increases with the increase of the distance from the blast.

Jan 1, 2015

By L. Wilson, M. Kotzel, T. Pienaar

An empirical equation is presented for the maximum airblast from unconfined charges. This has been tested at a number of sites and with charges ranging from 0.1kg to 311kg. The equation is developed to predict community response to potential explosive test range sites and the testing has added to our knowledge of the effectiveness of mitigating measures. The first site had 10m to 15m high walls that were intended to ameliorate the airblast. These walls functioned to a limited extent and reduced the airblast levels by 2dB to 5dB. The airblast was affected somewhat by topography. Noise levels at the nearest residences exceeded 130dB for charges larger than 1kg, whereas the vibration levels were very small. Formal complaints were received where the airblast level exceeded 128dB as per conventional expectations. Pedestrians and pets in the suburbs were startled by the blasts, emphasizing that the community response is much more sensitive to noise and airblast than vibration levels. The maximum airblast levels were too high for this site to be used on a regular basis. At another site, the airblast levels were significantly increased downwind by up to 10dB due to a moderate wind. A third site, at a quarry, produced unconfined airblast levels beneath the derived limits, but are much higher than the normal quarry blasting. By involving community forums there were no complaints, possibly due to desensitization by the normal blasting activities. The study has highlighted new areas for research in understanding the effect of noise, air blast and vibration on the low cost and informal housing typical in South Africa

Jan 1, 2011

By Adrian Moore, Alan Richards

A real-time system for prediction of the effect of meteorological conditions on airblast overpressure levels has been established in the Hunter Valley Coalfield in Australia. Real-time meteorological data from continuously operating sounding equipment and a predictive meteorological model is input to an atmospheric refraction model that enables the effect of meteorology on airblast overpressure levels in the area surrounding the blast site to be evaluated. Graphical outputs from the model, which are superimposed over a scaled airphoto of the mine and surrounding area, show the extent that airblast levels will be increased. When combined with inputs that quantify the effect of blasting specifications, the airblast levels that will result in the surrounding area from the combined effect of blasting specifications is determined. The model permits those responsible for blasting to make more accurate decisions on suitable times that blasting may take place to conform with applicable airblast limits.

Jan 1, 2009

By Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due quarry blasting. The natural limestone bedrock in occurs at or near the surface in southeastern peninsular Florida. While the shallow overburden soils is advantageous for mining purposes, vibrations from blasting has been a contentious issue in South Florida due to the proximity of the mines to several residential communities. White Rock Quarries and Krome Quarries are two active mining facilities in South Florida which generate numerous complaints, insurance claims, and lawsuits from residents in nearby communities who claim that the vibrations cause damage to their houses. Both quarries are located on the eastern edge of the Everglades, with thousands of nearby residences at the western edge of development in Broward and Miami-Dade Counties. Data obtained from over 400 publicly available blast monitoring and associated seismograph reports from White Rock Quarries were reviewed and compiled. The data was used to emperically develop a conservative estimate of the ground attenuation rate based on the scaled distance from the blast origin, which can be compared to Figure B-1 from USBM RI 8507 to determine whether it is feasible if damage could have occurred at a given property.

By Alejandro Rosario, Ricardo González

The restrictions imposed by the Brazilian environmental legislation regarding natural caves lead to a block of substantial amount of mineral reserves. Mining activities can released caves, as long as the company ensures that the activities will not cause any damage to them, requiring profound and time-consuming studies. Since the use of explosives in the mine are potential sources of some damage to any structures, it leads to a deep need for controlling the rock blasting activities. In this context, the maximum charge per delay used in operations close to cave regions must follow some internal blasting assumptions that have been developed during specific tests and mining activities. By the seed wave technique, it is possible to determine the behavior of a seismic wave, which travels through a rock mass and it is generated by blasting a known explosive charge. This technique has proved to be an effective tool because it is able to accurately include the physical characteristics of the rock and different lithologies. This paper discusses about modelling blasting induced vibrations in order to improve caves protection, which surround the mining operations.

Jan 1, 2019

By J. Fresnillo, M. Lopez Cano, S. Burgada, P. Couceiro, A. Jafa

This paper explores the sustainable use of the explosive’s energy for rock blasting and its role on the performance of downstream unit operations in mining applications. Since energy efficiency is becoming important for long term mining strategies, cost-effective optimization strategies are required to increase productivity and revenue while minimizing environmental impact. These optimization strategies involve continuous ability to model and measure all related phenomena and operational performance, integrated under a continuous improvement program where all involved counterparts act in close coordination. Although mining is complex, it can be regarded as a set of interconnected processes, where energy is consumed in a sequence, following all unit operations from the pit to the concentration. In this sense, the performance of downstream operations is potentially influenced by the initial energy input, since the explosive is the source of all energy used for rock fragmentation and heave. In this line, sustainable energy blasting is recognized as one of the main strategies for mine energy optimization projects. Finally, a special case study from an important gold mine in South America is presented, where benefits of a sustainable blasting energy strategies has been proved to deliver important downstream benefits.

Jan 1, 2019

By Jan Mehren, Arild Neby

Underwater Tunnel Piercing or Lake Tap, often also called the Norwegian Method, will in many projects be an important part of the hydro electric development scheme. The very last blasting round in the Lake Dorothy Lake Tap Tunnel, which penetrated into the lake at a depth of 120 ft (36 m), was such a key step in constructing the Lake Dorothy Hydroelectric Project. A lake tap project is multidisciplinary. Besides the pure blasting and construction technique aspect, engineering geological and geometric considerations that aim to optimize the tunnel alignment making a lake tap possible at minimized risk are of significant importance. Output data from numerical model analysis of the hydrodynamics resulting from the blasting is vital for the final adjustments to the geometrical layout. The planning of monitoring systems for the surveillance of hydrodynamic impact on valves and pipes as well as control with water levels and air pressures prior to and during the blasting, are all additional crucial elements in the design. More than 600 lake taps have been successfully performed in Norway since the 1890`s. The technique, which deserves to be called well proven, has been applied mostly in the hydropower sector but over the last 20 years also for shore approaches in the oil and gas industry. The demand for this technique seems to be ever more growing.

Jan 1, 2009

By D Maxwell Ellett

This report presents an evaluation of knowledge concerning a process used in predicting ground motion resulting from large scale conventional explosive detonations, The shots were set off in Arizona in connection with copper ore recovery activities.

Jan 1, 1976

By A. S. Romphf, C. K. McKenzie

Recent full-scale field studies involving single-hole charges fired to free faces under a wide range of operating conditions have delivered precious insights into airblast characteristics and propagation. The field tests involved production blasthole diameters in the range 89 to 406 mm (3 ½ to 16 in), bench heights in the range 9 to 24 metres (30 to 79 ft), burden ratios (burden/hole diameter) in the range 14 to 51, stemming ratios (stem height/hole diameter) in the range 11 to 36, explosive types of ANFO, heavy ANFO and pumped emulsion, and both solid-column and double-decked charge configurations. Around 700 measurements of peak amplitude and wave shape were made in all directions (0 to 360 deg) from the free face, from 38 single-hole tests in nine North American operating quarry/mine environments. The most striking observations were the strong dependence on directionality of the wave propagation parameters and wave frequency, the consistency of wave shape which resembled the modified Heelan wavelet, and the occasional appearance of distinct, multiple pulses from single events, shown to be echoes/reflections from quarry faces. In-hole deck charging failed in this study to achieve expected peak overpressure reductions, with the peak overpressure levels in Pascals/psi/millibars being approximately 40% higher than the as-charged weights. Inter-deck delay times in excess of around 25 ms are required for effective reduction of peak overpressure levels from front-row holes. Simple linear-superposition models based on synthetic wavelets applied to large production blasts produce composite waveforms which capture the important features of the actual pressure-time history, and correlate well with measured waveforms.

Jan 26, 2026

By Joshua Micah Hoffman, Lifeng Li, Jhon Silva-Castro

Since millisecond detonators were first introduced, at least two variables among others have been more closely considered when timing a mining blast; the accuracy and the precision of the initiation system. Unfortunately, those variables are often ignored when designing timing for mining blast. Despite the lack of consideration of the characteristics of the initiation system, in some situations, e.g., firing a blast hole with one deck and two detonators, changes in the blasting sequence can be the results of the overlapping between blasting charges. The consequences of such overlapping involve flyrock events, fragmentation and diggability problems, and other difficulties affecting the operation of the mine.

Jan 1, 2015

By R. F. Favreau, Favreau Patrice

"The economy profits from the rock excavated in mines and quarries and the excavations required for the construction of roads and buildings. However such excavations are achieved by blasting withexplosives, and explosions create fly rock and vibrations which in some cases may throw rock far intoinhabited regions and may vibrate buildings excessively in these regions. Society, however, no longeraccepts that their quality of life be disturbed by the risks of fly rock or the perturbation of vibrations.Thus it is important to know how to design blasts that do not cause excessive fly rock or vibrations, and to understand why sometimes a blast does create excessive vibration or fly rock. An article presented at the 2015 ISEE (reference 1) explains how unacceptable vibrations can be avoided, while the present article explains why dangerous fly rock occurs and how it can be avoided. The article shows by rigorous calculations with the blast simulator Blaspa that long range fly rock can be due to short collar or short burden, but mainly it explains how inadequate blasting that allows the floor to rise can cause even further reaching fly rock, a situation not usually recognized by most blasters."

Jan 1, 2016

By Sebastián Seria, Jorge Álvarez, Diego Cáceres

The capacity to break the rock into adequate size fragments and in a cost-effective way is one of the main challenges in large open pit copper mines in Chile. That capacity is often compromised by the accuracy of geological estimations and the resources allocated by the mine site to update those models, making the blasting design highly dependent on that input and in consequence, blasting results. Given these opportunities, having an alternative method to input estimated key geological parameters allows blast designers to modify their designs and apply the appropriate energy to achieve the desired results. By using measurement-while-drilling data from boreholes and a few samples of actual, widespread, hardness measurements on site, we can deliver an updated cost-effective hardness estimation that is used as an input to improve the blasting design and its results on fragmentation. This estimation is delivered as a hardness interval – often in MPa units- related to the position of actual drilling measurements. In addition, having a sufficiently large drilling dataset allows us to predict hardness in new, undrilled areas near already measured boreholes, serving as a prior estimation available before pattern design. The use of these estimations, applied to several copper mines in Chile, allow us to more accurately determine explosive amounts and borehole drilling, which directly contributes to more productivity and efficiency in mine site operations. The results are often related to narrowing the gap for fragmentation results, even so, in some cases that will be related to direct savings in Drilling & Blasting process in a range 5-10% of the budget, due to powder factor changes.

Jan 26, 2026

By Craig Adams, William Poe

Introduction The United States Department of the Interior, Minerals Management Service (MMS) is mandated under the Outer Continental Shelf Lands Act (OCSL A) and the Energy Policy Act of 2005 to oversee leasing, exploration, development, and production of mineral and renewable energy resources on the Outer Continental Shelf (OCS). Under these authorities, MMS is responsible for permitting and overseeing an array of offshore operations; some of which involve the underwater detonation of explosive charges. Explosives are most critical for their use in the severance of bottom-founded piles and well components during the decommissioning of OCS platforms and well abandonment work.

Jan 1, 2011

By Frank Hirthammer

Over the past few years, development and implementation of digital logistics solutions has convinced users of many additional advantages of this technology. Barcode labeling and reading increases the company’s efficiency and safety by reducing handwritten documentation and preventing misinformation. Sustainable information and productivity management is a significant advantage in competition. Since manufacturing information is tracked throughout the whole supply chain until the final consumer, all processes become transparent what ensures efficient risk tracking, correct disclosure to authorities (if required), and the compliance with company rules.

Jan 1, 2018