Search Documents

By Jean-Francois Lagueux, Andre Pomerleau

Goldex Mine is an underground mine located near the town of Val-d’Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long holes stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23.0 M tonne (25.3 M ton) of ore, large blasts up to 1.8 M tonne (2.0 M ton) are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km (0.62 mile) radius of the mine site.

Jan 1, 2011

By D Vrkljan, Z Ester

Excavating the building pit for the World Trade Center at Rijeka, it was necessary to blast over 160000 m3 of hard mass in fused condition. The building pit is located at a densely populated residential part of the main Croatian port Rijeka, close to the railway-track and traffic routes of the town. The permanent seismic monitoring points are foreseen on endangered housing and infrastructure facilities around the pit during designing and excavation of it. The seismic monitoring has been performed on 15 permanent points by occasion of over a hundred production and continuous blasting operations. The article considers the speeds of ground oscillations depending on applied maximum quantities of explosive charge according to fire degree, total quantities of explosives at the mine-field, structure of explosive charge, applied delay of mine boring and lines initiation mode and rock mass structure

Jan 1, 1999

By Ginn Huh

The blasting work to construct a subway in Seoul, Korea have often caused increased neighbor’s complaints because of ground vibration. In order to prevent the damage to the structure, it was necessary to predict the level of blasting induced vibration and to determine the maximum charge weight per delay within an allowable vibration level. The effect of blasting pattern, rock strength and different explosives on the blast-induced ground vibration was studied to determine the maximum charge weight per delay within a given vibration level. The blasting vibration was measured from 10 sites along the subway line in Seoul and an empirical particle velocity equation from over 100 test data was obtained, V=K(D/W1’3 )-” , where the values for n and K are estimated to be 1.7 to 1 S and 48 to 138 respectively.

Jan 1, 2000

By Alastair Torrance, Gary Cavanough

Approximately 1.5 million tonnes of ammonium nitrate are transported annually across Queensland, Australia—equivalent to nearly 100 truckloads per day. This is in the form of both AN prill and ammonium nitrate based emulsions (ANE). In a recent incident, a collision involving an ANE tanker resulted in a detonation that caused extensive blast-related damage and led to the closure of a major highway. Had this event occurred within a populated area, the consequences would have been catastrophic. For over a century, investigations into the causes of such spontaneous detonations have been inconclusive. A recently completed industry supported research project has made a pivotal discovery: a surface reaction mechanism leading to hydrogen generation has been identified as a precursor to detonation. If sufficient hydrogen accumulates and subsequently ignites, it can release enough energy to initiate the detonation of bulk ammonium nitrate and ANE. Controlled experiments conducted during the project successfully demonstrated hydrogen-driven detonation events. Previous work by Proulx and Scovira, presented at the 2000 ISEE Conference, described spontaneous detonations in hot, reactive ground and the mitigating effects of buffered emulsions and ANFO. Building upon their observations, this study reproduces similar incidents under laboratory conditions, confirming that hydrogen generation also results from reactive ground interactions. Importantly, the findings challenge traditional assumptions, demonstrating that ammonium nitrate and ANE detonation in reactive environments does not require an ignition temperature threshold, confinement, or a classical chemical decomposition pathway.

Jan 26, 2026

By Alan Diaz Butron, Eng. Thierry Bernard

"In tunnel blasting the most challenging objective is definitively obtaining the maximum advanceassociated to a minimum overbreak. Achieving 100% of advance with no overbreak is the targetchallenge by Chavimochic Consortium. Chavimochic Special Project is an irrigation system that extends throughout much of the coast of the La Libertad Region, on the north coast of Peru. In 2012, it began management for construction of the third and last stage of CHAVIMOCHIC to irrigate lands of Chicama Valley, North of Trujillo. This project of 13 Km (8 mi) of various tunnels, it's a combination of technology and daily optimization by experienced people, which allow to accomplish the objective. Achieving this advance with no overbreak provide a huge saving on time. This paper describes the method, technology used, and the results obtained on more than 600 blasts done with conventional initiation system on the first 3 km (1.86 mi)."

Jan 1, 2017

By Andrew P. Ritter, Douglas A. Anderson, Stephen R. Winzer

We have adopted a unified approach to blast design. Based on earlier research, we chose minimum relief of 3.4 ms/ft between holes in a row and 8.6 ms/ft between echelons to produce good fragmentation. A model has been created which generates the expected ground vibration frequencies from a particular delay pattern. Within the relief guidelines, blast designs have been created to shift the expected frequencies of the ground vibration above the resonant range of residential structures. A programmable sequential blasting machine was used to delay circuits. An extensive three-month seismic monitoring program determined that this approach is successful. From data collected for over a year, we have determined that crusher throughput is up about 10%, frequency modification has been largely successful, peak particle velocities have generally gone down by a factor of 2, and neighbor complaints have decreased drastically.

Jan 1, 1982

By Michael Noy

Current image based systems used to measure fragmentation are measuring the two dimensional presentation of a set of three dimensional objects. A two dimensional measurement of fragmentation restricts both sampling and particle size classification and hence provides a different evaluation of the fragmentation to that of a conventional sieve analysis of the same sampled material. Many modern image based fragmentation measurement systems attempt to convert this two dimensional analysis to a three dimensional analysis in order to deliver a "real" measurement of the fragmentation distribution. This paper questions the necessity and validity of this transformation and lays down the framework for the establishment of a standard in fragmentation measurement based on a two dimensional analysis. The results of image based measurements of laboratory prepared samples indicate that differences in mass distributions (3D distribution) can be mapped by an appropriate image based analysis which provides area versus particle size information.

Jan 1, 1997

By Romel B. Villanueva

At the Yanacocha gold mine, in the Andes of northern Perú, the first instrumental tests were carried out in October 2019 to detect the initiation sequence of a production blast by detecting the EMF signal produced by the detonation from each blast hole in the sequence. Several experimental tests were carried out to choose the correct antenna and find the best setup of the high-speed Data Acquisition device (DAD) to detect these electromagnetic waves. Finally, the first measurement was obtained. With the instrument recording at a rate of 1 million samples per second, the initiation sequence was detected with 99.5% accuracy. It was found that it corresponded, without a doubt, to the designed scheme. The main result is that these tests provide us with a method and instrumentation to verify if the planned initiation sequence is carried out correctly in the field. In this way we can find operational deviations and detect possible misfires. This method has proven to be accurate, fast and easy to implement, mainly requiring an EMF signal capture equipment that can record at very high speed, something that is increasingly easier to satisfy with the development of microcontrollers. On the other hand, the type of antennas used in this method are low cost and very commercial. These tests have improved our understanding of the nature of detonation and have marked a new milestone in the development of blasting instrumentation in Peru.

Jan 21, 2025

By Paul Worsey, Delbert Da, Eric Achelpohl

The University of Missouri-Rolla is currently researching the concept of using glass microspheres in explosives as taggants as part of a 3-year technical project funded by the Bureau of Alcohol, Tobacco, and Firearms. These taggants are intended to provide two functions, first explosive detection and second post explosive event identification. The key priority is being able to detect explosives used in terrorist acts prior to detonation. The research on the use of microspheres includes the development of indicator taggants for the purpose of revealing the presence of hidden explosives, by either emitting radiation when bombarded with neutrons or emitting selective vapors, such as DMNB which may be readily “sniffed”. Of secondary importance, after an illegal explosion, the tags serve to identify the lot number, etc of the explosive. This information is to aid in the tracking, arrest, conviction and imprisonment of the perpetrators.

Jan 1, 2001

By I. Petrovsky

Presence of the ground water, especially flowing water, causes limitations in the type of the explosives, which can be used for the blasting development in the open cats and quarries. This presents really big problem in Russia, because more than 70% of the blasting holes are wet and filled by flowing water. The waterproof explosives need to be used in these conditions, which increases the cost of the blasting development. So the search of the methods to remove the water from the blasting hole and to prevent direct contact of the explosive material with the water is important. It will give possibility to use nonwaterproof explosives (such as ANFO) and decrease the cost of the blasting development.

Jan 1, 2003

By Gene Baker

A new Safety Library Publication (SLP), SLP-27, which is titled “Security in Manufacturing, Transportation, Storage and Use of Commercial Explosives” was recently released by the Institute of Makers of Explosives (IME). SLP-27 makes recommendations for both general security and enhanced security at explosives sites when security risk levels, declared by the Department of Homeland Security (DHS) using its Advisory System, have temporarily increased.

Jan 1, 2006

By A. Spathis, I. Yacob, A. Labriola, G. Smith

Wall control is a significant issue for many mines. Improvements to the design process for blasts adjacent to temporary or final walls will require better measurement tools and predictive models. Orica Explosives has developed capability in both these areas and uses them to guide better wall control blasting practices. Vibration and gas pressure were monitored behind a series of production blasts and single hole blasts at the Freeport Grasberg Operations Opencut Mine. The blasts used ANFO in both 3 11 mm and 35 1 mm blastholes in a blast design which reduced the charge weight by between 30 to 50% in the final row of the production blasts. Single hole blast data were obtained by delaying the last hole in the production blast. Vibration levels were within the range often associated with vibration induced damage: 178 to 1080 mm/s at distances between 14-75 metres from the blast.

Jan 1, 2001

By Zvonimir Ester

The course of motorway tunnel under construction was set only 2 m away from the main motorway. The thickness of the tunnel overburden rock was 9 m. During the tunnel construction the traffic on the motorway was not supposed to be interrupted. The tunneling was carried out by NATM with classical drilling of blastholes and by blasting.

Jan 1, 1998

By Farshad Rashidi Nejad, Ali Asgari, Sanaz Norouzi

Blasting is known as the first step of rock breakage in mines. An indication of the importance of blasting is that more than 1 billion kg (2.2 billion lb) of explosives are used annually in Australia and 3 billion kg (6.6 billion lb) in the United States for rock breakage, more than 85% of which is used in the mining industry. The notion that blasting, as the first step of comminution, plays a significant role in crushing and grinding energy consumption is not an unfounded thinking. It can be noted that the comminution electrical energy consumption decreases in these ways: First, if the feed size to the primary crusher is decreased, less energy will be required to crush the ore to the same product size. Second, a decrease in work index (Wi) related to additional macro fracturing and micro fracturing within individual fragments.

Jan 1, 2015

By Brian W. Stump

The cessation of testing of any nuclear explosive devices in all environments is the goal of the Comprehensive Test Ban Treaty. In order to assure compliance with such a treaty, an international monitoring system has been proposed. This system will include seismic, infrasound, hydroacoustic and radionucleide monitors located throughout the world. The goal of this system is the detection of any nuclear test. In preparation for this treaty, a series of monitoring system tests, focusing primarily on seismic observations, have been undertaken. The most recent of these tests, Group of Scientific Experts Technical Test Three (GSETT-3), provides valuable data for assessing future monitoring systems. During the course of this experiment, seismic events associated with earthquakes, nuclear explosions and mining explosions have been recorded. This presentation will discuss the numbers and types of mining explosions triggering the system, in a particular area. Possible implications for the mining industry will be explored.

Jan 1, 1997

By Roberto Folchi

"This article deals with the excavation of a tunnel below the town of Isola LIRI, nearFrosinone, in central Italy. The tunnel was driven into a conglomerate formation, of lacustrine_fluvial origins, consisting in carbonate clasts with a sandy_silty matrix and calcitic cement. ""Drilling andblasting"" had to be adopted in place of a tunnel boring machine which had showeduneconomical performances. Good advance speed rates were achieved notwithstanding thepresence of some above structures to safeguard. The nearest structure (an old votivechapel) was less than 10 meters (33 ft.) far from the tunnel crown; the nearest residentialstructure was at about 15 m (49 ft.)."

Jan 1, 1993

By N. Powell, P. Hunt, A. Wetherelt

This paper considers the current methods of analysis employed, the validity of assumptions made and the reliability of results and predictions derived; where appropriate, alternative methods are proposed which are more accurate and can be applied with greater confidence. In regard to data collection, new local blasting data has been analysed and conclusions drawn but, due to the restricted amount of space available, reference to data set A only has been made in the text. The problem of mathematical model choice is considered and results for two and three parameter power laws are compared. The very important matter of parameter determination is discussed fully, with major emphasis being placed on the comparative merits of log-log linear, log-log planar and direct power law regression. Supporting data analysis examples are included. Assumptions regarding the normality of ‘best-fit’ regression model residual distributions are questioned and the reliability of associated safety limit determinations is discussed.

Jan 1, 2003

By Lee B. Paterson

Mining Engineers throughout the world have an appreciation for the importance of the role of the Blasthole Drill in one of the primary elements of the mining process. This paper highlights areas that could influence the overall cost effectiveness of that process of breaking rock and the associated downstream mining and ore recovery activities - and how the drill is designed and configured to meet that challenge. Factors influencing drill productivity and overall cost effectiveness are addressed, particularly regarding the benefits which are not necessarily reflected in the drilling process and therefore more difficult to quantify. This paper explores some of the downstream benefits of what we do to the drilling process.

Jan 1, 2000

By Paul Downing

Anyone in business today knows how difficult and time consuming it is to keep abreast of new and revised federal regulations. Those in the explosives industry know that such a task can be next to impossible as the regulatory environment faced by those in the hazardous materials community continues to undergo a major overhaul following the events of September 11th, 2001. This paper will attempt to clarify today’s regulatory picture by identifying some of the regulatory “hotspots” and “pitfalls” that affect individuals and companies involved in the sale, transportation, distribution and use of explosives.

Jan 1, 2003

By Sandra Penttinen

To assist blasting professionals with the creation, documentation, and appropriate methodology to standardize the data collection of the pre and post blast investigation process. Penttinen Associates will present a logical non-technical presentation focusing on: Why pre-blast surveys SAVE How to prepare for pre-blast inspections What to do in preparation of pre-blast inspections The creation of an industry standard all-inclusive pre-blast document Establishing pre-blast inspection operational standards Preserving the data.

Jan 1, 2001