Search Documents

By Christopher Jon Preston

This paper describes a type of ammonium nitrate (AN) produced in a patented experimental atomization/aerodynamic process. This AN exhibits outstanding properties for use as a main ingredient to a new family of AN-based commercial explosives. Micro-particle ammonium nitrate (MP-AN) is produced by atomizing either an 83% or 85% AN solution which has been doped with a two component surfactant NSol 1000 (NSol). NSol imparts some water-resistance as well as provides a means of increasing density and bulk strength. Increased detonation velocities, well in the range of emulsion explosives, can be achieved. The maximum manufacturing temperature is less than 100°C. The methodology has the potential of being environmentally friendly since any effluent can be recycled back into a make-up tank to be re-used by the closed loop method. The process has a small footprint.

Jan 1, 2015

By Dominic Orf, Gregory Poole

On December 12, 2018 at 4:14 AM EST, an earthquake registering a 4.4 magnitude on the Richter Scale occurred in central Tennessee. According to a survey posted on the USGS website, this earthquake was felt throughout the southeast and even as far away as Arnold Nebraska. That’s over 900 miles (1,448 kilometers) from the epicenter. We recorded the vibrations from this earthquake on 44 different seismographs that were set up with remote access to continuously monitor vibrations from blasting activities. Having this data gave us an opportunity to compare the vibrations caused by earthquakes and blasting. A simple observation of the amplitudes, frequencies, and durations is enough to notice that vibrations from earthquakes are very different than vibrations caused by blasting in mining and construction. We were also able to observe the dissipation of the vibrations from the earthquake and see if the low frequencies, that are typical of earthquakes, dissipate at a consistent rate. Regression calculations were performed in order to see if there was a good data fit and if a specific vibration prediction could be made based on the magnitude of an earthquake. “How does quarry/mining/construction blasting compare to the Richter Scale?” This is a very common question that we get from homeowners when discussing vibrations due to blasting activities. This paper is intended to provide some simple answers for such a complicated question. Both the Richter and Mercalli scales are compared to the particle velocities as they were recorded from this earthquake.

By Jose a. Sanchidrian, Ramon G. Eguren, Javier L. Amigo

On December 2013 a MEMU exploded at a blasting site in Norway, after burning for more than two hours. This paper describes the analyses made to determine the actual yield of the explosion, the lessons learned from the event and the actions taken as a consequence. The conclusions of the analysis were the following: - The yield of the explosion was 650-1450 kg TNT. In terms of AN and ANE they correspond to 1300 – 3700 kg AN, or 950 – 2450 kg ANE or ANE/AN blend. These quantities are 8 to 31 % of the explosive precursors in the truck. The burning of the truck and its load for two and a half hours had consumed more than two thirds (perhaps up to 90 %) of the explosive precursor material.

Jan 1, 2016

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Scott Crabtree, Randy Wheeler

Theoretical description of destructive wave interference and the use of sacrifi cial holes is included and is supported by data collected at Springfi eld Underground. Finally, the process by which the reduction in vibration was achieved in practice is described. Results are discussed for several production blasts taking place over a one year period.

Jan 1, 2008

By Braden Lusk, Tristan Worsey, Nathan Rouse, Kyle Hall

Loading explosives up hole has challenges that are typically not seen in down hole explosive loading. Most explosives applications are not up hole. Lack of experience and technology can cause significant problems when loading explosives up hole. When results aren’t achieved, the blame is commonly put on the design when the true problems are unknown. Not knowing the cause of the problem causes drill and blast designs to be over engineered and very costly with little success. Being able to know and record key data is crucial to actually solving the problem. This paper goes over blast instrumentation that can be used to trouble shoot drill and blast problems in up hole explosives loading in underground mines. The tools and procedures used to trouble shoot include velocity of detonation recorder, borehole tracking, seismographs, and borehole camera. Each item will be discussed in detail with a case study to show the usefulness of the instrumentation. The operation discussed in the case study had issues pulling raises and had hang ups in the stope shots. These problems caused production slowdowns and costly remediation blasting that was not very successful. The case study is an underground gold mine that used modified sub-level caving with backfill as the mining method.

Jan 1, 2018

By Nadya Michel, Daniel Gros-Jean

This is a true story. Names have been changed to illustrate the importance and impact of carbon monoxide risk management in explosive blast projects and the community « Honey I’m not feeling good…” “What is going on Michael?” – – Michael was not answering so Julia, who was on the third level of the magnificent house, hurried down the stairs to check up on him in the basement. Today was day 2 of the construction work of the bathroom, yesterday they had excavated all the space for the shower. She started to breathe heavily as she was approaching the bathroom and saw Michael unconscious on the floor. “Michael!” – Julia immediately dialed 911. She opened a window since the air was heavy and went by Michael to hear him breathe and take his pulse. The paramedics took Michael on a stretcher and rushed him to the hospital. “I’m feeling dizzy” she thought to herself a couple of hours after the incident, and heard Matthew say: “Mom, I’m feeling sick”. Suddenly, she felt like she would pass out and felt in danger but couldn’t move. She desperately searched for her cellphone and dialed 911 but couldn’t speak. The dispatcher sent the firefighters and paramedics to the GPS location that was appearing on the screen and the emergency team was alerted that it was a second call in hours at the same address. When the firefighters arrived, they had to force the door to enter and found Julia in her bedroom on the third floor and Anette and Matthew also unconscious in their bedroom, lying on their respective bed. There was no smoke but on their multigas meter, carbon monoxide (CO) peaked at 1500 ppm on every level of the house, which is abnormally high.

Feb 6, 2023

By P D. Kasbanis, Lyall Workman

"The energy output of an explosive is typically calculated using an equation of state and computerapplications. Results are reported as weight and bulk strength, either in absolute terms or relative toANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of “available energy” associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated."

Jan 1, 1996

By Robert Hopler

A blast caused the destruction of a bridge and loaded freight train and the death of three men, near Chattanooga, Tenn., on May 16, 1907. The blast and its disastrous effect has been described by Mr. Hunter McDonald, M. Am. Soc. C. E., in a paper read before the Engineering Association of the South and reprinted in the Proceedings of the Association for April-June, 1907. The excessive damage was so largely due to coincidence and wreckage of the bridge and train so complete that the incident is worthy of notice.

Jan 1, 2008

By R. Frank Chiappetta

A new blasting technique has been developed by International Technologies, LLC. to eliminate subgrade drilling, lower ground vibrations, improve fragmentation and reduce explosive consumption. The new technique utilizes a uniquely designed borehole plug, with a bottom hole air deck and a predetermined stemming mass on top of the plug. This combination is referred to as the Power Deck?. Single holes and full scale tests were conducted by Blasting Analysis International, Inc. (BAI) to determine how the system works, the mechanisms behind its success and the best design parameters to use for the given rock conditions. Results have shown reduced or eliminated subgrade drilling, ground vibration reductions of up to 33%, reduced explosive consumption by 16 to 25%, and improved fragmentation by up to 25%. This paper summarizes the methodology, field test setups, analyzes procedures and results for one series of single hole and full-scale tests which were performed in a Pennsylvania, USA quarry.

Jan 1, 2004

By John Watson

New Technologies, New Challenges and New Opportunities For quite some time now, numerous explosive manufacturers have spent untold man-hours and millions of dollars trying to develop a blast initiation technology that would “once and for all” provide users with what was once believed to be only a theoretical possibility...nominal timing. Zero “cap scatter” (the amount of variation of delay timing from the targeted nominal) has been the industry’s goal ever since delays were first introduced into the marketplace. Just as adding delay time between blast-holes improved blast performance since their introduction, having the wrong delay or a poorly timed blast has proven to be very inefficient and in many cases hazardous. The question of how precise a blast initiation system needs to be still remains unanswered, but electronic detonator systems being used today indicate that significant improvements can be achieved over conventional pyrotechnic detonators. These systems can typically provide single digit millisecond ranges of variability, if not sub-millisecond in some cases.

Jan 1, 2003

By Richard E. Danell

"There are a variety of approaches for wall control blasting in open pit mining operations. Safety forworking in the pit is the principal benefit. There are also a number of economic and productivitybenefits when appropriate techniques are used. The purpose and requirements of wall control blasting can vary quite significantly for different operations. When considering blast design, geology, geotechnical factors, drilling, explosives, economics and blasting history are all part of the engineering design process. In many operations, there is a high reliance on blasting history and economics for determining wall control blasting measures. This presentation outlines approaches that broaden the design process and discusses their advantages."

Jan 1, 1997

By Robert Hopler

That some time in the year 1872 there was organized an association composed of practically all of the manufacturers of gunpowder and other high explosives in the United States, the members of which said association were as follows: E. I. du Pont de Nemours & Co., The Hazard Powder Company, Laflin & Rand Powder Company, Oriental Powder Mills, American Powder Company, The Miami Powder Company, and Austin Powder Company of Cleveland, all of which or their successors are defendants herein; that the object and purpose of said association was the elimination of all competition between the members thereof in the shipment and sale of gunpowder and other high explosives among the various States and Territories of the United States; that the only manufacturers of gunpowder and other high explosives which did not join such association at the time of its organization were the California Powder Works, The Sycamore Manufacturing Company, and The Lake Superior Powder Company, but your petitioner alleges that each of said three last named companies

Jan 1, 2008

By D. J. Leidel

The offshore production of oil and gas resources has been active in the Gulf of Mexico since Kerr- McGee drilled the first commercial well out of the sight of land in 1947. Since then, approximately 60% of the offshore oil/gas production structures used globally have been erected in the GOM to support the production of energy resources’. The shallow, shelf and shelf edge waters of the Gulf of Mexico have reached or are rapidly approaching production maturity, requiring that the fixed structures used to support energy production be removed or otherwise disposed of by suitable means. The use of energetic materials has been determined to be a safe, efficient and cost effective technology to remove fixed offshore structures whose service life has been exceeded.

Jan 1, 2002

By Ron J. Elliott, Dylan Wedgewood

A series of five signature holes were blasted at the Highvale Mine and the resultant seismic data was analyzed to make recommendations on how best to address neighbour complaints regarding blast vibrations. From an analysis of peak vibration levels measured at the closest neighbour for blasting during 2016, it was determined that the blast vibration intensity varied between 1.4 to 4.3 mm/sec (0.06-0.17 ins./sec.), well below the level of concern for the onset of minor damage to residential structures, however, the frequency of the blast vibrations was between 2.2 and 9.7 Hz, which is within the range of the natural resonant frequency for a single story home. This was determined to be the cause of the neighbour complaints, as the home would be responding to the blast vibrations.

Jan 1, 2018

By Paul Downing

A typical day for a blasting company includes what seems to be an infinite list of tasks dealing with numbers. Whether determining the exact amount of explosives material in inventory, the number of holes in the shot, the exact distance from the blast site to the nearest exposure, or the capacity of bulk hoppers, the accuracy of numbers is key to ensuring the safety of the public, property and personnel.

Jan 1, 2008

By Jim Mikelait

Overview ?? Why do we need security? ?? Needs assessment ?? Elements to any security system ?? Protect, Detect, Alert, esponse ?? Electronic Security System Criteria ?? Advantages and Limitations of Various Security Options ?? Internal measures to protect against potentially harmful employees ?? How can technology improve my business?

Jan 1, 2006

By Tom Treleaven

The widening of the Panama Canal to approximately 130 feet (40 m) for its entire length began just a few years ago. The original expansion program was slated for completion in 18 to 20 years, but has recently been reduced for completion within the next four years. This means that a tremendous amount of blasting at simultaneous points along the canal, by both the Panama Canal Commission (PCC) and many subcontractors, is necessary to achieve the new completion deadline. The accelerated program also imposed many logistical concerns, since marine trafIic is always heavy and cannot be stopped for blasting. Because some of the large and heavy cargo vessels clear the bottom of the canal by only about 6 feet ( 2 m), the blasting cannot result in any large boulders into the center of the canal, for fear of grounding and damaging a vessel, not to mention the traffic delays and lost income of approximately 1 to 2 million dollars per day.

Jan 1, 1997

By Jake Hutchison, Wade Hutchison

The opposition to the project has risen as a result of some political pressures and from public perceptions about the project’s necessity and its impact on the neighborhood. As a result of this controversy, the Underground Conservation Hall was quickly termed “Bredesen’s Bunker” by the Media. Close exposures for blasting, required by the Conservation Hall construction project, have been regulated by specifications that regulate seismic monitoring, pre-blast and post-blast inspections. Planned blasting for the project included blasting to a depth of 30 feet (9.14 meters) within 35 feet (10.67 meters) of the front of the newly renovated Tennessee Executive Residence. Excavation for the project found more competent rock at higher elevations than identified in test drilling which required blasting within 2 feet (0.61 meters) of the side of the Residence.

Jan 1, 2009

By Jarrod Bonsmann, Zachary T. Plitt

"A surge in mine related deaths in Middle Eastern conflicts over the past few years has prompted research into the mitigation of the impact on a blast loaded vehicle. In past military conflicts, it has been observed that blast loading can cause injury to the brain but the exact cause is unknown [1]. The recent rise in deaths due to Improvised Explosive Devices (IEDs) has led to research that has speculated that the high acceleration experienced by soldiers on a blast loaded vehicle leads to Traumatic Brain Injury (TBI) [2]. This research aims to investigate vehicle designs that can reducethe peak acceleration for passengers on board the vehicle, in the event that the vehicle is blast loaded by an IED."

Jan 1, 2016

By Claude Cunningham

Difficulty has always attended the evaluation of rock breaking energy available from explosives, owing to the complexity of the way in which it is released, and the destructive amplitude of the pressures. Many problems have arisen and continue with this difficulty, including the following: I. Formulation of improved compositions to deliver appropriate energy levels to the blasthole walls, or to deliver previous results at improved cost. How appropriate is it to use various ingredients, such as Aluminium, water, salt? 2. Claims over energy issues, resulting in wasted time and expense, over things that sound good in theory but are very difficult to tie down. 3. Purchasers of explosives make decisions based on claimed “Bang per Buck” from different manufacturers, where the estimate of “Bang”comes from simplistic numbers from various, very unequal detonation codes. The above problems are escalating as time progresses. Using the high level IDeX PC 2000 detonation code, we have found a way to portray the differences between formulations in a way which relates to their breaking effect in the field. The basic method is to plot the adiabat from the detonation state to full expansion in units which express the practical implications. Energy alone cannot deliver results, so we use the curve to examine its manifestations: pressure and temperature. Internal energy is plotted with these. The method displaces relative energy numbers, as it portrays the context in which the energy is available. It is used here to compare an ANFO, an emulsion and a doped emulsion, as well as the effect of Aluminium. The effect of the shock pressure regimes and temperature correlate well with what is seen in the field.

Jan 1, 2000