Search Documents

By Eduardo Lozano, Vilem Petr

The use of explosives bring countless benefits to our everyday lives in areas such as mining, oil and gas exploration, demolition or avalanche control. However, because of the potential destructive power of explosives, strict safety procedures must be an integral part of any explosives operation. The goal of this paper is to provide a solution against the hazards which unfortunately accompany the use of explosives. For this reason, a blast shield is specifically designed and tested for protecting personnel against these unpredictable effects. This document will develop a complete analysis answering the following questions: what are the potential hazards from an air blast; what are their effects; and how can we be protected against them. In order to answer these questions, theoretical, analytical, and numerical calculations are performed. Finally, a full blast shield prototype is tested under blasting conditions proving its effectiveness as a safety device while explosives are used.

Jan 1, 2015

By Mick Fritz, Gregory Poole

Construction blasting is always challenging when in close proximity to existing structures, but when you are next to a landmark like Sanford Stadium at the University of Georgia it can get intense. Blasting on this project was performed less than 100 feet from students studying in their dorms at Reed Hall. Some shots are only a few feet from the columns on the stadium that hold up the sky boxes where meetings were being held while blasting was being performed. If a shot goes vertical the rocks would go through the floor of the sky boxes.

Jan 1, 2011

By Deepesh Yadav, B. S. Choudhary

Underwater drilling and blasting is conducted for deepening of sea channels for port berths, lake or reservoirs for water supply etc. so that rock dredging becomes easier. During this process there are several associated unwanted effects having potential to cause damage to surrounding structures and the environment, flora and fauna. Though all these ill effects can’t be completely eliminated but adopting controlled blasting techniques can minimize these to tolerable levels. It is recognized that ground vibrations resulting from rock blasting below water near dam may endanger the safety of earthen dams. Therefore, controlled blasting technique was used to ensure the safety of dam and its efficacy was established by monitoring of blast vibrations. The usage of small quantity of explosives confined in blast holes, non-electrical delay detonators and initiating each hole with a separate delay helped to minimize the ground vibration effects on surrounding structures.

Jan 1, 2018

By Mark S. Stagg, David E. Siskind

The Bureau of Mines arranged to have a wood-frame test house built in the pat of an advancing surface coal nine so it could investigate the effects of repeated blasting on a residential house. Structural fatigue and damage were assessed over a 2-yr period. The house was subjected to vibrations from 587 production blasts with particle velocities that varied from 0.10 to 6.94 in/s. Later, the entire house was mechanically shaken to produce fatigue cracking. Failure strain characteristics of construction materials were evaluated as a basis for comparing strains induced by blasting and shaker loading to those induced by weather and household activities. Cosmetic or hairline cracks 0.01 to 0.10 mm wide occurred during construction of the house and also during periods when no blasts were detonated. The formation of cosmetic cracks increased from 0.3 to 1.0 cracks per week when ground motions exceeded 1.0 in/s. Human activity and changes in temperature and humidity caused strains in walls that were equivalent to those produced by ground motions up to 1.2 in/s. When the entire structure was mechanically shaken, the first wallboard tape joint crack appeared after 56,000 cycles, the equivalent of 28 yr of shaking by blast-generated ground motions of 0.5 in/s twice a day.

Jan 1, 1985

By Lon Santis

Although unproven, it is suspected that there have been eleven locations since 1988 where explosive generated carbon monoxide (CO) gas moved through the earth and accumulated in nearby underground enclosed spaces. This paper summarizes the incidents, which involved about 30 suspected or medically verified CO poisonings and 1 fatality. Ten incidents occurred in residences and one occurred in a manhole. Although practically nothing is known about the mechanism behind the suspected gas migration, review of the incidents and available information indicates there are certain warning signs and a successful remediation technique available. In each case, overburden heavily confined the explosive in the blasts, preventing release of explosive-generated gases to the atmosphere. All the blasts were in residential areas, and none were excavated immediately. Where the distance from the blast was recorded, 5 of the blasts were within 20 to 50 feet (ft) (6 to 15 meters [m]) of the underground enclosed spaces, 3 were 100 to 150 ft (30 to 46 m) away, and 1 was 400 to 500 ft (120 to 150 m) away. Investigators often identified suspected pathways from the blast site into the underground enclosed spaces. One technique appeared successful at quickly correcting an existing condition. This technique involved applying negative pressure to the earth and removing the CO from the ground surrounding the underground enclosed space.

Jan 1, 2001

By Ayman Tawadrous, Hendrik Botha, Simon St J Tose

The early miners and their mules always had the challenge of transporting unstable dynamite underground. The modern pumpable explosives, whilst far safer, still present a major logistics challenge for the mobile charging units (MCU). The challenge today is the efficient explosive delivery into declines, ramps, and vertical shafts, often requiring the MCUs to travel excess distances up and down to surface to re-load. Alternatively, the management of cassettes or ISO containers is utilized to deliver the pumpable base emulsion to the MCUs at the working face. Additionally, local laws and regulations regarding shaft clearance further compound the task and result in pausing other operations in the shaft or decline or ramp until the completion of the explosive transport. This paper examines the research & development challenges of dropping base emulsion down a vertical pipe to depths in excess of 1000 m (3280 ft.), either to an underground storage or directly into the MCU, depending on the depth. The boreholes (with pipes) are drilled in close proximity to the underground work areas. The paper also discusses the rheology of the emulsion within these vertical pipes as well as the economic benefits of such an innovative system. The learnings gained from this work, along with examples demonstrating the significant reduction in MCU travel and the safety benefits, are presented for the industry to consider moving forward.

Jan 21, 2025

By Robert Hopler

Of the common causes of the larger mine accidents, such as falls of roof and coal, gas and dust explosions, mine fires, and the misuse of explosives, all of which are often closely related, each must be studied and fought in a manner peculiar to itself. The last mentioned, the misuse of black powder and other explosives, is sometimes considered the least important of these causes of mine accidents; but its importance is much greater than the statistics indicate, for the reason that the misuse of explosives is the true cause of many of the fatal mine fires, gas or dust explosions, and falls of roof that are credited to other causes.

Jan 1, 2012

By Conny Postupack, Jim Petrunyak, John Hope

The authors discuss the concepts, engineering considerations, and cost relationships involved in the use of drilling and blasting to accomplish backfilling and reclamation with minimum use of mechanical equipment. The four xchods o f reclsnacisn now in use are reviewed, and their advantages and disadvanrages a r e nocea. Guidelines for seleccrng a particular method are offered in terms of applicability under varying geologic, economic, and technological condirions.

Jan 1, 1989

By J. Sigler

A series of small scale tests have been performed to establish the effect of powder factor and initiation timing on the grindability of rocks. The blasts were performed in high quality granite blocks, which were cut from stone prepared by dimensional stone quarry operations. Three different types of granite were tested. The charge configurations included detonating cord placed in five holes with water as a coupling medium or concentrated charges of equal mass, placed in the same number of holes, fully stemmed or air decked. The powder factor was varied from 0.4 to 1.2 kg/m3. Typically all charges were detonated simultaneously; however, in some experiments, detonation waves collided in the middle of each borehole and in others a small delay was used between charges. All fragments were collected and screened, and drop weight impact tests were performed on selected size fractions, using different impact energy, to calculate the resistance of the rock to impact breakage. The work index of some of the blasted samples was measured using a standard Bond mill arrangement. The experiments generally showed increased softening of the rock with powder factor, which appeared to be the dominant factor. Charge configuration as well as in-hole collisions of detonation waves affected the initial fragmentation but had little effect on the impact breakage of the samples.

Jan 1, 2008

By R. Alford

In the modern world of demolition safety is paramount and unnecessary or unquantifiable risks are not accepted (FasterCapital, 2024) and all risks must be kept As Low As Reasonably Practicable (ALARP) (BSI, 2017). This principle has led to a huge reduction in deaths in the last 50 years and the statistics continue to improve although this is starting to plateau (Beal, 2007). Under normal circumstances, this is now simply part of the normal way work is done and systems are in place to ensure both safety and economic profits are assured. What happens when the environment is less controlled and risks are unknown, such as after a natural disaster, war, an accident or a stand-up from a failed demolition attempt? A dangerous structure cannot responsibly be left alone with a fence around it so some action must be taken, but how can this be done safely and responsibly? An incident in Didcot, England in which half of a power station’s boiler house being prepared for an explosive demolition collapsed suddenly, killing four men in 2016 provides a useful case study of how technology, creativity and planning can be used to conduct complex demolition fully remotely to avoid any further risk to life.

Jan 21, 2025

By Dr. Anthony J. Konya

The modern era has seen a boom in virtual training platforms. This study details the effectiveness & applicability of online training in comparison to in-person training for the drill & blast industry.

Feb 1, 2020

By Jason Baird, Philip Mulligan, Caleb Baumgart

This report details the pressure variances, measured at four pressure sensors placed equidistant from the center of an airburst explosion, as the blast pressure from a single charge expands radially. Many of the empirically derived equations used for predicting the blast pressures of an explosion, assume a point source detonation and that the radial pressure expansion is equal. The authors understand that the equations used to approximate the blast pressure may not have 100 percent agreement with the observed pressure. However, during previous research at Missouri University of Science and Technology (Missouri S&T) the pressure variances had a range of 1,200 psi, between the four pressure sensors placed two feet from the center of a 1/2-pound (226.8 gram) of hand packed C4. The variances indicated that at the close distance from a suspended explosive charge the pressure does not behave as that observed from a point source.

Jan 1, 2014

By Robert Hopler

RBH Note: in 1913 black powder was still dominant as a coal-mining explosive, but permissible explosives were making some slight headway. For example, in 1902 there were only 11,300 pounds of permissibles used in coal mining, but in 1913 the quantity was 21,801,285 pounds. However, there were 187,551,653 pounds of black powder used that year. It took many years before the use of black powder ended in coal mining. From the picture of the miner reparing his explosives it’s hard to tell what he’s using, but the fact that a wooden Du Pont powder box is shown, he’s probably not using black powder. That doesn’t mean he’s using a permissible, either, since that was not yet a requirement. It’s interesting that the miners have open flame cap lamps, and the miner is actually smoking a pipe while preparing his explosives.

Jan 1, 2014

By B S. Petri, N T. Rouse

Underground limestone mines generally lack air pressure monitoring procedures and instrumentation guidelines. The blasting industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground mines. This became apparent during the development of a new underground limestone mine, where overpressure levels from production blasting needed to be estimated. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting. Therefore, a study was conducted to (1) identify and review any published studies for data that may be applicable, (2) identify the appropriate equipment required to record the overpressure levels, (3) determine the proper procedures for setting up the equipment and recording overpressure, and (4) provide an understanding of the nature of the air overpressure in a developing mine.

Jan 1, 2014

By Paul Klaric, Nicholas Bodley

Every blasting engineer or professional can attest to the age-old conundrum of obtaining accurate hole information on a large scale prior to loading explosive charges in a blast hole. Even though the benefits of QA/QC are well known and documented and are becoming increasingly important when digitizing and automating mining operations, the QA/QC process itself has not changed significantly over generations. The current methods where operators deploy measuring tapes of variable standards recording their subjective assessment of hole length on a paper blast map or manually transcribing to a tablet, are unreliable and non-auditable. Additionally, the process in its current form is time intensive, obtaining only moderate results and benefits, making it difficult or impossible to resource in today’s tight labour markets. Often only two data points, depth, and water presence, are captured when visiting the hole resulting in a high cost per bit of data. For these reasons, the process is seldom done on a large scale, let alone integrated. The QA/QC process in its current shape is a gap that will need to be addressed if autonomous blasting and mining is to become a reality.

Feb 6, 2023

By G. Cavanough, A. Torrance

Emulsions have been developed for over forty years to become the most common water-resistant explosives used in the mining industry. An emulsion is a common commodity, with many examples in our day to day lives of one immiscible liquid dispersed in another. They have varying degrees of stability from a few seconds to years. What makes their application in explosives unique is twofold. They contain a high concentration of salts in the dispersed phase and also have a far larger volume of dispersed phase than continuous phase. The continuous phase contains at least 75% by weight of an oxidizer such as ammonium nitrate dissolved in water. The crystallization point of these solutions is often >60oC which means that the formation of the emulsion has to occur at an elevated temperature. Once the emulsion is cooled, its structure helps to prevent the formation of crystals in an otherwise unstable system. At room temperature there is a considerable potential for the small oxidizer droplets to crystallize which is countered by the strength of the oil layer and also the size of the emulsion droplet. If the emulsion droplet is too large then crystals can form which may lead to rapid deterioration of the emulsion and overall crystallization, accompanied by a temperature rise as the heat of crystallization is released from the emulsion. The size of the emulsion droplet is critical in preventing crystal growth and subsequent droplet coalescence and emulsion break down. One method of examining emulsions and understanding their structure is to use optical microscopy to measure droplet size and also emulsion deterioration from shearing, temperature cycling and when contaminants are introduced, such as detergents, different oil types, coating agents and dust particles. This paper reports on advanced techniques to quickly assess emulsion quality and stability

Jan 1, 2024

By Patrick Cahill, Jacob Miller, Nolan Mundwiller, Catherine Johnson

"The Experimental Mine at the Missouri University of Science and Technology is undergoing major developments. The underground workings are being expanded to include a ramp down to a second level which will comprise of larger opening and room sizes to better simulate modern mine layouts. Thisexpansion will enable the Experimental Mine to be utilized for many more generations. In addition, the new 15,000 sq. ft. Kennedy Mine Building is being constructed and will house the mine office,classrooms, and three laboratories to accommodate the mining and explosives engineering programs’ ever-increasing enrollment. With these new developments come an increasing need for safety and awareness in regards to explosives and blasting. This paper will utilize the Institute of ExplosivesMakers Safety Analysis of Risk (IMESAFR) software tool, to assess current magazine compliance withthe increased personnel limits and mine building location. Furthermore, this paper will assess theimplementation of a wireless blast warning system consisting of warning beacons and a centrally located siren which will be integrated with the construction of the Kennedy Mine Building. This warning system will provide the necessary precautions to safely conduct blasting-related experiential learningopportunities and research projects, and will enable facility staff to more efficiently oversee blastingoperations at the Experimental Mine. "

Jan 1, 2017

By M. Syafiq Isnaya, Rahma Norfaeda, Slamet Rachman Jaka

This paper is about project improvement to maximize energy distribution while ensuring beneficial blast results (reduce boulder condition). The main problem is how to manage complex lithology conditions related to detonation propagation in energy distribution control.

Feb 1, 2020

By Luan Monteiro, Francisco Biulchi

The AngloGold Ashanti - Cuiaba mine sought innovative approaches to minimize lateral development and stope extraction time while maintaining optimal gold recovery and minimizing dilution. The stope 8GAL EXT 30 was selected as a case study. Traditionally, conventional blasting methods in such a scenario would necessitate either a single mass blast or slot development at each end of the stope. These methods typically compromise recovery and dilution or increase development time and risk. Additionally, conventional wired detonators require workers to re-enter the stope between blasts to load blastholes and connect detonators. The wireless initiation system offers a solution by initiating blastholes using magnetic induction signals that can penetrate rock, air, and water. This technology allows a pre-charged stope to be mined without requiring workers to re-enter the area between blasts to charge and connect blastholes. Engineers from Orica and AngloGold Ashanti designed a new extraction sequence utilizing the wireless initiation system. The process began with the opening of one end of the stope using a conventional slot and wired electronic detonators. Subsequently, pre-loaded rings were fired in three blasts to extract the opposite end and the intersection. The 8GAL EXT 30 stope was successfully mined using this technology enabled method. Each blast was meticulously monitored, and the stope void was scanned to assess blast performance. The results demonstrated a 4.6% improvement in recovery and a 16% reduction in dilution compared to the initial plan, and reduced exposure of people to hazardous locations in the stope. These results represent an additional value of USD 200k, gained from implementing wireless initiation to enable this particular blasting schedule.

Jan 21, 2025

By Luiz Guilherme Isfer Maciel, Marilena Cardu, Fernando Golin, Jacopo Seccatore

"This study applies the concept of the difficulty of tunnelling by drilling an blasting (D&B) to selectedcases from the Brazilian tunnelling industry. The difficulty of tunnelling has been defined in previouswork as the difference of specific drilling (SD) from industrial average trend: easier when SD is lowerthan average, more difficult when SD is higher than average. Results show how tunnels in Brazil tend tobe unrealistically more difficult to excavate when compared to similar excavations in similar geologies elsewhere in the world. It is thoroughly discussed the reason for such anomaly (up to +90% SD compared to industrial average). One reason could be the lack of options amongst explosive products on the brazilian market. Only ANFO and explosive emulsions are available in Brazil. Lacking high VOD(Velocity of Detonation) products might result in reducing the maximum allowable burden amongstproduction holes, therefore increasing SD. Another reason could be found in the tunnel designers’tendency of choosing D&B as excavation method for weak rock masses that would benefit from mechanical excavation. The reason to this tendency can be partly found in the lack of availability of mechanical excavation machines in the brazilian market. Blasting in weak rock masses requires more careful smooth blasting, hence a closer spacing amongst contour holes to avoid costly overbreak: this increases SD. A third reason could be found in the lack of skill amongst the local workforce. When dealing with unskilled workers the blast designers naturally tend to avoid highly optimized blasts thatrequire very skilled workforce to be realized on field. The designer in this case tends to leave the blastdesign simpler but more robust, at the cost of higher specific drilling and specific charge. The conclusions suggest that this unrealistic difficulty when compared to world average could be a simptom of the so-called “Brazilian cost” within the tunnelling industry."

Jan 1, 2017