Search Documents

By S. Q. Zhu

Coal Water Mixtures (CWMs) are densed suspensions of coal particles in water. Viscosity is one of the most important rheological properties of CWMs and it is desired to be as low as possible. The slurry viscosity was influenced significantly by additive formation, the particle size distribution and the ash content of the coal. However, the influence of dispersants is most obvious. At present, there are several kinds of dispersants such as polymeric styrene sulfuric sodium, lignin sulfonate, humate, polycarboxy salt, ethylene epoxide surfactant. In this paper, a newly synthesized CWM dispersant has been reported, which is an efficient anionic surfactants of polycarboxylic acid type. The synthesis process includes three steps. At the beginning, the polyglycol acetate ester has been performed by acetic acid and polyethylene glycol (PEO) on the condition of acetic-acid/PEO ratio 1:1.1, at 368~373K for 30 minutes. Then the macro-monomer is prepared through the esterification of 85.71% acrylic and 14.29% polyglycol acetate ester, at 368~373K for 10 minutes. After that, the polycarboxylic acid CWM dispersant is polymerized using proper proportion macro-monomer, acrylic (AA) and sulfonic styrol sodium, at 368~373K for 1 hour. This new dispersants are used in the coal water mixtures formulation. Four kinds of coal used in the experiment are Shuang Yashan, Tunliu, Luning, Changcun samples. ? The highest concentration for shuanyashan coal is 70% when the dosage of dispersant is 0.4%, and the content of -200 meshes particles is 75.53%. As the dosage of dispersant de-creases to 0.25%, the Shangyashan CWM concentration is 67%. ? For Tunliu coal CWM concentrations are in the range of 76% to 75% when dosage of the dispersant changes from 0.4% to 0.25% at the same particle size distribution of 83.5% minus 200 meshes. ? The highest concentration for Luning coal is 69% when dosage of the dispersant is 0.4%, and the content of -200 meshes particles is 88.86%. ? For Changcun sample, the coal concentration of CWM is 73%~75% when dosage range of the dispersant is 0.35%~0.5%. The experiments show that the synthesied dispersant is quite promising for some coals CWM preparation, but a little bit coal-dependent. The Proximate and Ultimate analysis, surface characteristic measurement have been made to investigate the interactions between coal and additives.

Jan 1, 2014

By D. J. Zhao

The reduction and nitridation of preoxidized ilmenite pellets were investigated with the prospect of creating grain refiners containing titanium oxides and titanium nitride dispersoids. All the reduction and nitridation reactions were conducted in a furnace with a thermogravimetric analysis system under a H2-N2 gas mixture of 5 L/min. The ilmenite pellets were reduced at 1100°C for 4 hours under 80%H2-20%N2 gas mixture, and then respectively nitrided at 700°C, 800°C, 900°C and 1000°C for 12 hours under 10%H2-90%N2 gas mixture. The products were characterized by X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM), and analyzed by Energy Dispersive Spectrometers (EDS) and Electron Probe Mapping Analysis (EPMA). Iron oxides were reduced into metallic iron, and oxides of titanium were found, but titanium nitride particles were not identified in the products under the prevailing conditions.

Jan 1, 2014

By Elzbieta Mielczarski, Jerzy Mielczarski, Jan Drzymala, Yann Duvalm

Polyethylene glycol monoalkyl ethers (CnEm) render quartz hydrophobic while feldspar remains hydrophilic. As a result quartz can be separated from feldspar in small frothless flotation devices such as the Hallimond tube. The separation can be accomplished at room temperature at pH < 7 and C16E33 concentrations between 10-5 and 10-4 M for quartz particles smaller than 0.4 mm. No separation is observed when feldspar ore containing about 60 % of feldspar and 40% of quartz is subjected to flotation in a laboratory flotation machine. The reason for the lack of separation is a low hydrophobicity of quartz in the presence of polyethylene glycol monoalkyl ethers and high intensity of mixing in the flotation machine. The flotometric tests showed that the contact angle of quartz in monoalkyl ethers of polyethylene glycol solutions is less than about 18 degrees and depends on the structure and concentration of the ether and the pH of the system.

Jan 1, 2003

By Robert Dunne

A review of the current ?state of the art? of refractory gold treatment will be provided. This will include a global perspective of the refractory processes that are being practiced, where they are and some discussion on why the processes were selected. Some discussion on the challenges that face the refractory gold industry will also be provided.

Sep 1, 2012

As a leading global company in the mining sector, we are committed to sustainable development. To this end, we invest in the responsible, integrated management of economic, environmental and social issues. Vale?s objective is for our businesses to produce local, regional and global prosperity, enabling the construction of a positive legacy throughout the lifecycle of our activities. This covers everything from talking with stakeholders and preventing failures to complying with legislation, paying constant attention to environmental issues and respecting ethics in business. Keywords: sustainable development

Sep 1, 2012

By V. K. Gupta

Selection of mill size for reducing a feed material of a given size to the desired product size is generally based on the specific energy estimate obtained from Bond test. Over the last thirty years or so, an attempt has been made to develop a more accurate and powerful alternative approach based on the characterization of the particle breakage kinetics and material transport through the mill over a range of operating conditions of interest and correlating the degree of size reduction achieved with the net specific energy input to the mill. Particle breakage kinetics are described in terms of the specific grinding rate and breakage distribution parameters for the individual size fractions. Precise estimates of these parameters and the net energy input to the test ball mill (a laboratory or pilot scale mill) are important for development of desired energy-size correlations. In this context, three tasks are important: (a) preparation of the feed charge, (b) design of batch grinding experiments and (c) computational technique used for estimation of the breakage rate and breakage distribution parameters. This paper highlights several aspects of these three tasks that have been overlooked by researchers working in this field, and describes a more appropriate approach for estimation of model parameters and specific energy input. Several examples are included based on the data available in the literature and those generated in our laboratories to illustrate important points.

Sep 1, 2012

By Alain Broussaud

The lecture is about the growing role and the evolution of advanced process control (APC) in the mining and mineral processing industry, taking into account major trends in Information Technology. It reflects the standpoint of a team, which has already successfully developed APC technology for more than 20 years. Advanced process control systems tend to rely on combinations of artificial intelligence techniques or algorithms that complement each other and cooperate. Each technique or algorithm makes it possible to use certain type of knowledge about the process, so that the advanced control systems benefit at any time from the combined knowledge of process and control engineers and plant operators, from knowledge derived from past research work and process modeling, from a considerable amount of data provided by advanced instrumentation in real time, and from knowledge that can be extracted automatically and at any time from past data and images. The lecture will first review and compare the role, merits and limitations of algorithms that are used for online decision making in mineral processing plants: expert systems, fuzzy logic, neural networks, soft sensors, optimizers, and MPC controllers. The lecture will also review the role of online image analysis and sound analysis in process control. Recent developments in this area open new dimensions, in particular the ability for advanced process control algorithms to automatically explore the past, move back and forth in time in order to make better informed decisions, and the ability to cooperate with the operators for better performance. Applications will be presented. Recent progress in process simulation makes it possible to design, configure, check, and pre-tune APC systems before plant startup, opening new options for implementing APC. In conclusion, the author will share his experience about the key ingredients for sustainable success in APC Keywords: mineral processing plants, APC, MOC controllers

Sep 1, 2012

By C. Tokoro

Co-precipitation of dilute toxic anions with ferrihydrite is an important removal mechanism in wastewater treatment system. Although, numerous qualitative studies have been published on removal characteristic from wastewater of dilute anions by co-precipitation treatment, detail mechanism or quantitative characteristic is not well understood. This paper discussed the co-precipitation mechanism of As(V) and Cr(VI) with ferrihydrite by comparative experiments between co-precipitation and simple adsorption. In this study, co-precipitation experiments and simple adsorption ones were distinguished closely. In the former, precipitation of hydroxides and adsorption of anions develop simultaneously, but in the latter, anions adsorb onto prepared hydroxides. Although high affinity anions for hydroxides (e.g. As(V) for ferrihydrite) showed quantitative difference of removal ratio between co-precipitation experiments and simple adsorption ones, low affinity anions (e.g. Cr(VI) for ferrihydrite) showed quantitative agreement in spite of deferent forms of ferrihydrites between them, that is, amorphous ferrihydrite was formed in co-precipitation experiments, but goethite was formed in simple adsorption ones. In order to discuss the mechanism of co-precipitation phenomena, three experimental studies have been carried out: (i) adsorption isotherm measurement in the co-precipitation experiments of As(V) or Cr(VI) with ferrihydrite, (ii) zeta potential measurement of co-precipitated or simple ad-sorbed ferrihydrite with As(V) or Cr(VI), and (iii) XRD analysis of co-precipitated As(V) for ferrihydrite. All experimental results suggested the main mechanism in co-precipitation phenomena of As(V) was not only a surface complexation (simple adsorption) but also a surface precipitation.

Jan 1, 2014

By Mohammad Kor, David Beattie, Agnieszka Mierczynksa-Vasilev

The selectivity of polymer adsorption in mixed mineral systems is the basis for polymer depression of gangue minerals in flotation. Effective polymer depressants not only reduce gangue mineral recovery, they also have minimal effect on the recovery of the value phase, presumably through targeted adsorption on the gangue phase, and minimal uptake on the value phase. Traditionally, polymer depressant design has been guided by single mineral phase adsorption tests, with affinity and maximum adsorbed amount determined for gangue and value phases separately. However, there is a need to determine the actual extent of adsorption on the gangue phase while in the presence of the value phase. In this work, we report on the development of in situ atomic force microscopy (AFM) imaging for determination of polymer depressant coverage and morphology on mixed mineral surfaces. Our group has previously used AFM imaging on single minerals to connect adsorbed layer characteristics with bubble-particle attachment and flotation outcomes. Two sample types were used to test the methodology: (i) a mixture of two crushed/ground minerals encased in resin; and (ii) a composite mineral sample containing macroscopic regions of three different mineral phases. The samples have been used to probe the selective uptake of two modified dextrin polymers (octenyl succinate anhydride dextrin). AFM images acquired in situ (while all surfaces are immersed in the same polymer solution) of each mineral phase have revealed the natural selectivity of the polymer for the mineral surfaces. In all cases, the polymers adsorb on the all mineral surfaces present, but to a varying extent.

Jan 1, 2014

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

"Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching experiments indicated that copper extraction rate was accelerated by cupric and ferrous ions , and was higher at potentials below a critical value (critical potential) in the presence of these ions. This was in good agreement with the results of electrochemical measurements, i.e. in the anodic polarization curves for a chalcopyrite electrode, active-passive behavior was observed when cupric and ferrous ions co-exist, but the activation at low potential did not occur without these ions (Figure 1). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials.These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model."

Jan 1, 2003

By T. Ueda, T. Oki, S. Koyanaka

"Accurate assessment of the liberation state of crushed ore particles is important for efficient mineral processing. In general, the liberation state is assessed by two-dimensional (2D) measurement of polished ore sample sections. However, this 2D measurement inevitably suffers from overestimation of the degree of liberation, known as stereological bias. This arises from the fact that biphase particle sections of which only one phase happens to have been cut are indistinguishable from liberated particles. To date, several stereological correction methods have been proposed, but their applicability for various types of particles has not yet been sufficiently examined, and this tends to undermine their practicality. We have addressed this problem using a numerical-analytical approach in which various types of biphase particles are modeled, and the 2D sectional information is compared with actual three-dimensional (3D) information. Through simulations, we revealed a general relationship between the internal mineral structure of particles and the stereological bias. Finally, we have developed a unique stereological correction method in which the texture (a 2D pattern characteristic) of particle sections is used to estimate the internal structure of particles, and thereby the stereological bias. KEYWORDS Mineral liberation, stereological bias, texture analysis INTRODUCTION Mineral liberation assessment of 2D particle sections inevitably suffers from stereological bias; that is, overestimation of the degree of liberation. Stereological bias is caused by the fact that a composite particle can be misidentified as a liberated particle when only one phase happens to have been cut in sectional measurement. Stereological bias has attracted attention since Gaudin pointed out its importance in 1939 (Gaudin, 1939). Several attempts have been made to measure the 3D liberation state directly, avoiding the bias, using X-ray computed tomography (Gay and Morrison, 2006; Lin and Miller, 1996; Miller et al., 2003; Miller et al., 2009; Reyes et al., 2017; Videla et al., 2007). These have provided useful information through laboratory testing, but further technical refinement is necessary for practical usage, to overcome the technique’s limitations in terms of resolution, assessment of minerals of similar density, and speed. Therefore, for practical purposes, detailed information regarding mineral phase geometry is obtained by sectional analysis, using automated scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX)-based analysis (e.g., with a mineral liberation analyzer (MLA) (Fandrich et al., 2007; Sandmann, 2015)); and the development of an effective method of stereological correction, which predicts the relevant bias and transforms the measurable 2D degree of liberation into its 3D counterpart, is an important research aim."

Jan 1, 2018

By M. C. Harris

"In the flotation process the contact angle is an important indicator of the hydrophobicity of a mineral particle. There is considerable literature showing that the contact angle increases when the chain length of the alkyl group associated with the collector molecule used to render the valuable mineral particle hydrophobic increases. The extent to which an alkyl group interacts with surrounding water molecules is quantified thermodynamically by the excess Gibbs energy. In the present paper it is shown that there exists generally a strong linear relationship between the excess Gibbs energy of the alkyl group associated with the collector and the contact angle. The structure-activity of such alkyl groups is in turn related to the total surface area, molecular volume, the molar volume, molecular weight of the functional groups in the molecule and interaction energies. It is proposed that the demonstrated relationship is indicative of the role which the alkyl group component of the collector, which is attached to the mineral particle, plays in increasing the extent to which water molecules at the surface of the mineral are rejected from the surface thus increasing the contact angle. The relationship between excess Gibbs energy and surface tension is further explored with a view to relating the observations quantitatively to the parameters in the Young equation.INTRODUCTIONThe issue of wettability of materials is of great importance to many industrial applications. Wettability studies usually involve the measurement of contact angles which indicate the degree of wetting when a solid and liquid interact. As is well known the contact angle (O) is the angle between planes tangent to the surfaces of the solid and the liquid at the wetting perimeter which is the zone where the air, water and solid phase merge. When the air bubble attaches to the solid surface there is an increase in the air/solid interface area and a decrease in the solid/water interface area. For attachment to occur the cosine of the contact angle should be less than 1 and this will be promoted if the interfacial surface tension between the air and the solid (? SV) is low. Classically the relationship between these parameters has been expressed through the Young equation (1) for a perfectly flat surface:"

Jan 1, 2018

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"Silver is currently lost as jarosite during the pressure oxidation of sulphides and cyanidation of the residues yields 5-10% of silver. Efforts to recover silver from complex sulphides, which contain economic fractions of silver require an understanding of the behaviour of acanthite during pressure oxidation. However, previous studies of acanthite (Ag2S) reaction have been complicated by the formation of argento-jarosite and uncertainties arise on the interpretation of the results.In this work, the acid pressure oxidation of high-grade natural silver sulphide mineral (acanthite) was carried out at 110-150°C and under the conditions similar to that of pressure oxidation of complex sulphide. The predominant product of reaction is elemental sulphur. The rate of reaction increases with increasing temperature and with the presence of ferric ions. The kinetics is controlled by chemical reaction with activation energy of 72.6 kJ/mol. The rate of reaction decreases with the presence of silver sulphate in the initial slurry. The proposed overall reaction is close to: []"

Jan 1, 2003

By A. M. Raichur, S. P. Vijayalakshmi

Fine coal dewatering is a major problem in the coal industry because the fines hold significant amounts of water and account for two-thirds of the product surface moisture. Present methods include flocculation using polymeric flocculants followed by filtration. But the kinetics of filtration are not favorable with such flocculants. In this study, a novel method involving flocculation with microorganisms for improving the settling rates and dewatering kinetics has been investigated. Two Gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis were used as bioflocculants. The effect of time, pH and ionic strength of the electrolyte used on adhesion and flocculation were studied. Adhesion tests showed that maximum adsorption occurred in 20 minutes in the pH range of 2-7 and the total amount of bacteria adsorbed was almost the same with both the flocculants. Nearly 98% of the coal flocculated with both the microorganisms in about 5 minutes. The filtration rate of fine coal almost doubled with addition of bacteria and electrolyte and maximum filtration occurred near the point-of-zero-charge of the bacteria.

Jan 1, 2003

By Q. R. Chen

Wet processes are commonly used in coal preparation field home and abroad. Dry coal cleaning technology is very necessary in China because more than 2/3 of coal resources deposited in arid areas, which are difficult to separate coal with wet processes. A particular interest of this article is the discussion of separation research development of dry coal cleaning in China, such as an air dense medium fluidized bed (ADMFB) beneficiation technology, a compound dry (pneumatic) separation technology and a triboelectrostatic separation technology. The fundament and importance of dry coal cleaning methods above were introduced. On the basis of analyzing parameters which influence the performance of separators, including that of structure, technologic and operating, the separation research status of dry coal cleaning methods, especially the ADMFB beneficiation technology, were discussed and reviewed. The recent developments, especially the fluidized bed beneficiation for <6mm fine coal with an external energy assisted, including a vibrated fluidized bed and a magnetically fluidized bed, and the triboelectrostatic separation for <1mm fine coal are also introduced. The study and application results in China show that dry coal cleaning technologies can efficiently beneficiate different coals with different sizes. The ADMFB can separate >6mm coarse coal with an E value of 0.05~0.08, the external energy assisted fluidized bed can separate <6mm fine coal with an E value of 0.07~0.09, the triboelectrostatic technology can efficiently separate <1mm fine coal, and the compound dry separation technology can efficiently separate >3mm coal with a easy washability. The dry coal cleaning provides an efficient and lower cost clean approach for coals distributed in arid areas.

Jan 1, 2014

By R. Shiva Kumar, G. Sreedhar, S. Sharma

Some of the Indian origin iron ore deposits located in Bellary, Karnataka province are having peculiar characteristics of Iron ore deposits (Hematite) having Iron above 64% and 30-40% lump (-30+6mm) recovery which are not suitable to use in blast furnace due to not meeting the specification of Tumbler Index and Abrasion Index. In general for high grade Iron ores, process flow sheet involves crushing and screening (dry/wet). In the contest of high grade Iron ores located at Bellary sector of Karnataka state in India, lump generated from this process could not attain the required physical properties (Tumbler Index, Abrasion Index) and metallurgical properties , even though the grade of the lump ore is above 64% Fe. Washing techniques like Drum scrubber and Log washer play major role in improving the metallurgical properties of Iron ore lumps by removing the light and hard layers of clay, silica coated over the lumps. In this study the effects were compared of drum scrubbing and log washing on iron ore lumps. It is found that by incorporating simple washing technique i.e. drum scrubbing or log washing, Tumbler Index of Iron ore Lumps could be increased from 74% to 78% which is acceptable for use in Blast furnace. From the Drum scrubber and Log washer tests, it is clear that Log washers have an edge over Drum scrubber in removing hard coated clay on surface of Lumps. This simple washing technique facilitate us to utilize the lumps directly in blast furnace and eliminate the unnecessary crushing and grinding of the ore so as to meet the specifications of Sinter fines and pellet feed.

Jan 1, 2014

By Trevor Saldanha, Stephen Grano

A key uncertainty in flotation modelling is determining, a priori, the proportion of each mineral which will develop a certain rate constant for different feeds of variable liberation and hydrophobicity. First and foremost is the ability to predict the proportion of minerals that will not be recovered, even at very long flotation times, and which therefore report to the tailing stream as the non-floatable fraction (i.e., having a zero rate constant). Recent empirical evidence has shown there are at least two factors which contribute to heterogeneity in flotation rates and, in particular, the appearance of a non-floatable fraction - heterogeneity in the distribution of adsorbed collector amount on a particle-by-particle basis, even for the same liberated mineral in the same size fraction, and the existence of a critical contact angle below which the bubble-particle union is unstable. In this paper, inferred measures of the critical contact angle for liberated particles are compared with stability model calculations. This has demonstrated that the dependency of the critical contact angle with particle size and mineral specific gravity are explicable by bubble-particle stability considerations. This argument is further extended to the flotation behaviour of composite particles, as a function of liberation class, in which the wetting perimeter of the attached bubble on the composite particle surface is constrained by the presence of a surrounding hydrophilic domain for the case of simple binary composites. Reasons for the different flotation behaviour of composite particles having different textures, as noted in the literature, are also discussed in terms of the stability of the bubble-particle union.

Jan 1, 2014

By Zhang Yuejun, Feng Tianran, Shen Zhengchang, Han Dengfeng

"With continuous mining industry development and dressing plant scale expansion, flotation cell is developed towards to large scale and intelligence. Based on flotation cell scale-up theory and industrial practice, KYF-320 air-forced mechanical flotation cell with effective volume of 320m3 was successfully developed by Beijing General Research Institute of Mining and Metallurgy (BGRIMM) and adopted by China Gold Inner Mongolia Mining Co., Ltd, Luming project of China Railway Resource Group Co., Ltd, and Toromocho project of Chinalco in Peru. In this paper, the structure and technical characteristics of KYF-320 flotation cell are introduced, and the application of that equipment in China Gold Inner Mongolia Mining Co., LTD is demonstrated. The tank of KYF-320 flotation cell is cylinder-shaped, 8200mm in diameter and 7500mm high, with double froth lauders and large inclined angle cone bottom. 16 sets of KYF-320 flotation cells of which the processing capacity is 26,000,000 tons/a, are used in the second phase project of China Gold Inner Mongolia Mining Co., LTD. Their stable running shows the long life of impeller and stator and the power intensity (power consumption divided by effective volume of flotation cell) of KYF-320 flotation cell is only 0.73kW/m3 which is significantly less than that of small scale flotation cells. The industrial production obtains good results that the Cu grade of final concentrate of entire flotation circuit is 22.90% at the recovery of 86.73%, when Cu grade of feed is 0.35%, which indicates that KYF-320 flotation cell has good performance and can be widely used in large scale mine."

Jan 1, 2014

By C. Gomez, J. Finch, R. Dalhke, J. Torrealba-Vargas

"The dispersion of gas into bubbles is an essential feature of flotation machines. Three measurements have typically been used to describe the dispersion: superficial gas velocity (Jg), gas holdup and bubble size along with the derived quantity, bubble surface area flux. Measurement devices continue to be developed. The McGill Jg sensor based on accumulating bubbles by natural buoyancy comprises a tube with a valve and pressure transducer (Figure 1). The tube is immersed at a desired location and depth (H1) in a flotation cell. On closing the valve pressure increases to a maximum (P1) when the tube is full of air. The Jg is estimated from the slope of pressure-time curve (dP/dt).The relationship between Jg and dP/dt is derived from first principles. Testing the relationship is difficult in a flotation machine as the spatial variation in Jg is generally not known. This problem is overcome using a specially designed experimental setup and the estimated Jg is shown to equal the known Jg.The derivation reveals the importance of bulk density (?b). The sensor was modified to provide an estimate of ?b (Figure 2). A second tube was added immersed to a different depth (H2) and kept full of accumulated air giving a pressure P2. The estimate of ?b is given by (P1-P2)/(H1-H2) (i.e., at the end of collecting the pressure-time data). This two-tube sensor also helps dampen process noise as illustrated by a sudden change in level when collecting the pressure-time curve. Both the original and modified versions have been widely used in plant test work."

Jan 1, 2003

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018