Search Documents

By H. J. Wu

The optimum performance in mineral processing plants usually demands the optimum size reduction, which is frequently achieved by a closed grinding circuit. Due to the difficulty associated with fine size classification, the size separation efficiency in closed grinding circuit is usually very low, which leads to huge circulating load and significant overgrinding. Recent development of Der-rick Stack Sizer has made an efficient fine size separation down to 200 mesh with a satisfactory screening capacity. With the efficient fine size separation with Derrick Stack sizer, the problems commonly associated with typical closed grinding circuit, including high circulating load and over-grinding, have been eliminated. Feedback from numerous Stack Sizer applications in iron ore industry indicated that, compared with conventional fine size classification equipment, the circulating load achieved by Derrick screen was usually decreased from approximate 300% down to 60% or so, while the iron recovery has been increased by 6% to 8% only by more efficient size separation in the closed grinding circuit. To study this phenomenon, this paper discusses the relationship between size classification, circulating load and mineral recovery in the closed grinding circuit. A simulation model to predict the improvement in the grinding circuit from more efficient screening is also introduced with this paper.

Jan 1, 2014

By M. Guo

Coal-based Direct Reduction in Interior-combustion Shaft Kiln (CDR/ISK) is a brand-new technique. Compared with the traditional Coal-based Direct Reduction (CDR) technique, its main character is to use Interior-combustion Shaft Kiln (ISK) as the reactor of direct reduction. After being crushed and grinded, iron ore is made into green pellet, which will be surface-coated by coal fines. Then, the surface-coated green pellet can be directly reduced in ISK. The pellet should not be too dry and should be charged from the top of ISK. Oxygen-contained air should be blasted into ISK to keep the temperature in it higher than 1000 degrees centigrade, at which iron oxide will start direct reduction. The reduced pellet will be discharged from the bottom of ISK and after de-surface-coated, spherical Direct Reduced Iron (DRI) can be gained. The volume of carbon monoxide in the off-gas discharged from ISK is less than one per cent. By using this technique to get one tonne DRI, the consumption of coal is about 300kg of fixed carbon, which is much lower than the energy consumption by using other CDR techniques. There is a lot of complex refractory iron ore in China, which remains unexploited. The iron-bearing minerals in this kind of the iron ore can not be beneficiated economically by present technique of gravity, magnetic, flotation or magnetic roasting because the iron minerals are too very finely disseminated to be liberated, or, the iron minerals are too similar to gangue to be separated each other. By using CDR/ISK, complex refractory iron ore can be directly reduced in lower temperature and all kinds of iron mineral can be turned into iron metal. As the grains of iron metal growing larger during direct reduction, magnetic separation can be used to separate iron metal from gangue mineral, thus high-grade iron metal fines can be gained. According to the experiments, the grade of iron metal fines is above 90 percent and the recovery of iron is higher than 90 percent. The consumption of coal to process one tonne of complex refractory iron ore is only about 90kg of fixed carbon.

Jan 1, 2014

By Peter J. Coghill, Michael J. Millen, Brian D. Sowerby, Kirby D. Cunningham

"CSIRO Minerals has developed an integrated particle size analysis system for deployment in the grinding circuits of minerals processing plants. The system includes a slurry sampling station, a de-aeration tank and an ultrasonic particle size analyser (UltraPS). The UltraPS analyser is based on ultrasonic attenuation and velocity spectrometry combined with gamma-ray transmission. The technology is applicable to the measurement of 0.1 to 1000 µm diameter particles directly in highly concentrated slurries without dilution. The analyser incorporates a gamma-ray transmission gauge utilising an ultra-low activity radioisotope source that is exempt from International Atomic Energy Agency (IAEA) and Australian licensing regulations.The UltraPS analyser consists of a submersible probe and an electronics package. The probe can be immersed directly in a minerals processing plant stream if the aeration level in the stream is low. For applications where a de-aerated slurry stream is not available, CSIRO has developed an integrated system that includes a sampling station, a de-aeration tank as well as the UltraPS analyser itself. A schematic drawing of the continuous flow gravity fed system is shown in the figure. A commercial sampling system is used to supply slurry at a rate of 2.5m3/hr to the deaeration tank. The aim of the de-aeration tank is to remove air in the slurry to a level where meaningful particle size measurements can be performed. The tank volume is about 0.2m3, thus giving the slurry flowing through the tank a mean residence time in the tank of approximately five minutes. Tests at a number of concentrators have shown that five minutes is sufficient time for slurry to de-aerate to a level where ultrasonic measurements can be made. The tank incorporates an ultrasonic level detection sensor and flow to the deaeration tank is adjusted based on the level of slurry within the tank. The UltraPS probe is mounted through a flanged section of duct, which is bolted to the bottom of the de-aeration tank."

Jan 1, 2003

By Anuj Narang

Large-scale separation or flotation cells, used in the primary extraction in the oil sands industry, are integral parts of the overall process of bitumen extraction. Good regulation of the interface level between the bitumen froth and the middlings in these cells can result in a significant improvement in bitumen recovery and throughput, and heavily influence process economics. Automatic control of such industrial processes presents challenges such as multi-phase flow dynamics, variable process gain and time delays, poor quality of measurements and significant disturbances. This paper details a case study application of development of multiple models of the dynamics of the interface level and the design of model predictive controllers (MPC) for a separation cell process. A Model predictive controller (MPC) using linear models is designed and implemented in real time on an industrial separation cell. The industrial implementation results show that the MPC scheme provides significant benefits over the current operations which use a PID controller. The benefits include significant reduction in the variance of the interface level resulting in higher bitumen recovery and smoother downstream operation plus energy savings due to reduced underflow pump speed.

Sep 1, 2012

By M. Surracco, M. C. Tilocca

"Mineral comminution is often a costly process which also requires high level of energy. In the course of the studies carried out by the researchers of the Department of Civil-Environmental Engineering and Architecture at the University of Cagliari, aiming at the optimization of the reduction processes, it has been experimented, among of others, the effects of high-speed water jets on minerals grinding. As far as coal is concerned, some of the solutions initially adopted are presented in this paper, which essentially relied on the water jet power only, with secondary use of mechanical actions, to reach the most modern solutions that envisage the use of mechanical energy, normally used in traditional grinding machines, in synergy with hydraulic energy transferred by water jet.INTRODUCTION Mineral comminution can be rather expensive and demand a high-energy consumption, especially for fine sizes (Austin, 1979). Further interesting perspectives in this area may be offered by comminution means aided by high pressure water jets (Ciccu 2007), whose crushing potential is currently used for several operations such as cutting different materials, rock digging and industrial cleaning. The crushing action of water jets may induce a traction stress in materials where substances of a mineral nature, especially if characterised by permeable porosity, oppose a minor resistance (Griffith, 1920). The first solutions to this purpose essentially relied on the sole energy of water jets, with a secondary use of mechanical actions (Ciccu, 1993). Results were encouraging, despite the high values of specific energy for the low capacity of treatment. However, due to the difficulty in making the techniques mainly based on hydraulic energy practically applicable to solids comminution a solution was experimented, with some interesting results, consisting in the combination of mechanical energy, normally used in traditional grinding devices, with hydraulic energy transferred through water jets, in a synergic relationship (Ciccu, 1998; Tilocca, 2016)."

Jan 1, 2018

By Pan, Jian, Siwei Li, Deqing Zhu

"It is great significance to realize the efficiently and comprehensively utilization of iron, manganese and aluminum from refractory high-aluminum and high-manganese iron ores. Aimed at the two types of low grade refractory iron ores, mineralogical characteristics were studied. The direct reduction behaviors and evolution of mineral compositions of single iron ores and their blended ones were analyzed, and the corresponding reduction mechanisms were demonstrated. The results showed that only a part of iron oxides in high-aluminum ore are transformed to metallic iron after reduction, while the other react with aluminum and silica to form fayalite and hercynite which are difficult to be reduced. For the high manganese iron ore, most iron oxides can be reduced to metallic iron and manganese oxides can combined with aluminum-silica minerals to form galaxite and tephroite, promoting the reduction of iron oxides. Co-reduction results demonstrate that reduction of high- aluminum ore can be promoted by adding with high-manganese ore. Metallization and metallic iron grains increase dramatically by elevate high-manganese blending ratio. At the ratio of 60% high- manganese iron ore in the pellet feed, iron-slag separate well with a slag assaying 28.51%~36.35% Al2O3 and the recovery of iron and manganese can be reached 93%, respectively. The high-aluminum rich manganese residue was recycled with H2SO4. INTRODUCTION The growth of the Chinese iron and steel industry has been pushed forward by its rapid economic development in recent years, and 1126 million tons of iron ore have been consumed in 2014, where 933 million tons were imported according to the data from World Steel Association [1]. However, iron resources are limited, and especially the reserves of high-grade iron ores are declining, so it is of significant importance to optimize the mining rate of iron resources [2] and to utilize low- grade refractory iron resources, such as high-aluminum iron ore."

Jan 1, 2018

By V. Runkana, N. K. V. Nadimpalli, S. Sahu

"IsaMill™ has been in operation in the recent past for fine grinding of low grade ores to extract non-ferrous minerals. IsaMill™, typically, consists of a series of uniformly spaced identical disks mounted on a rotating shaft which is encased in an outer shell. The mill offers high energy efficiency for fine grinding and an inherent scalability. But, it encounters certain operational challenges such as non-uniform distribution of grinding media coupled with high wear rate of the disks and solid walls of the mill at specific locations—which adversely affect the mill performance. To circumvent these operational challenges, design modification of the disks through heuristics, by introducing a reduced diameter disk (RDD) at specific locations, is a common practice in industry. But there is no systematic scientific study in this regard. In the current work, we developed a discrete element method (DEM) based model and simulated for the IsaMill™ operation to study the effect of RDD on the efficiency of the mill and wear rate of the solid walls and disks. Since the first set of disks experience the high wear rate due to the high loading of the charge, the RDD was introduced at the first two disks. The simulations were performed at different diameters of the RDDs and at different media loadings. The performance of the mill was analyzed based on the power consumption, the wear rate on disks and the distribution of media particles inside the mill. Besides, the performance variables such as mean velocity of media particles and total impact energy provided useful insights into the milling operation. It was observed that the reduction in disk diameter yields lower wear rate of the disks at the cost of decrease in power draw at a constant high media loading. Whereas, when the media loading was decreased, the amount of wear and power drawn was comparable for both the most reduced and least reduced disk diameters. Therefore, there is an optimum choice of RDD for a given mill loading to maximize the mill performance while reducing the wear rate of the disks."

Jan 1, 2018

By A. V. Kozub, D. O. Sharkovsky, R. I. Ismagilov

"Due to complex mineral composition and fine ingrained nature concentration of iron ores deposited in Mikhailovskoye mine field requires application of wet magnetic separation to produce 65–66% Fetotal and 8.2–8.6 %SiO2, concentrate with 90–94% of material being –0.044micron grain size. Higher specific consumption of ROM, increase of production costs with concurrent reduction of output - those are inevitable side effects of desired concentrate grade improvement. Large-scale complex analysis and surveys have been carried out aimed at concentrate grade improvement with concurrent output increase. Classification of feed in hydraulic cyclones (hereinafter referred to as hydrocyclones) has been the bottleneck for improvement of processing throughput and concentrate output. Hydrocyclone classification efficiency is 50-60% and further improvement is practically impossible. Actual circulating load may achieve as much as 500-600% while the optimal rate is 200-250%. Application of wet fine screening has been considered to improve iron ore concentrate grade. Objective of this work is to design processing flow diagram for unoxidized ferruginous quartzites with implementation of wet fine screening. Large-scale tests have been run in Crushing and Concentrating Plant with application of wet fine screening stage. These tests included application of wet fine screening in 2 and 3 stages of classification to separate desired grain sized material; replacement of hydrocyclone classification with fine screening; application of fine screening as additional stages to concentration process and screening of final concentrate. Testing Methods. EXPERIMENTS AS WELL AS THEORETICAL RESEARCH HAVE BEEN APPLIED FOR THE PURPOSES OF THIS WORK; INCLUDING MAGNETIC, GRAIN-SIZE AND CHEMICAL ANALYSIS OF CONCENTRATION PRODUCTS. MODERN ANALYTICAL DATABASE HAS BEEN APPLIED TO STUDY WET FINE SCREENING FEATURES, MINERAL AND PHYSICAL COMPOSITION OF CONCENTRATION PRODUCTS. Work Results: - analysis of wet fine screening application for iron ore concentration. - technological solutions enabling to improve slurry classification of fine ingrained low magnetic iron ore have been developed. - effective process flow diagram including fine screening has been designed based on the feasible and reasonable arrangement solutions."

Jan 1, 2018

Copper nickel separation is performed by mineral processing techniques both pre and post smelting in Copper Cliff at Vale Canada?s Operations. The separation at Clarabelle Mill takes advantage of the ore mineralogy to affect a separation on the rougher concentrate where chalcopyrite and pentlandite exhibit high liberation and high recoveries thus their separation is simple although incomplete. The copper concentrate comprises only 50% of the copper in ore with the remaining copper being separated post smelting in the Matte Separation plant where the slow cooled Bessemer Matte is again treated by mineral processing operations using flotation to separate the chalcocite and heazlewoodite and magnetic separators to remove a metallic nickel alloy. This paper discusses the mineralogy, separation processes and work currently underway to improve the separation of copper from nickel in these plants.

Sep 1, 2012

By P. S. Mukherjee

Mineral ilmenite is a major resource for titanium, whose major application is for production of Titanium dioxide (TiO2) for pigment application. The production of pigment grade TiO2 from ilmenite was earlier carried out by acid leaching, which has now been banned due to environmental regulations. Further acid leaching leads to loss of iron metal values as sulphate or chloride which are also treated as effluent. In thermal plasma processing the metal values are recovered as high value pig iron and Titanium dioxide is recovered as Titania rich slag containing 80 to 85 percent TiO2. The Titania rich slag has now been considered as a better input material than synthetic rutile for production of pigment grade Titanium dioxide. On the other hand, high value pig iron goes for automobile industry for specific application. An Inflight-flight Thermal Plasma Processing plant, used for the production of Titania Rich slag and high value Pig iron from ilmenite, with 20kg capacity was designed and fabricated. The reactor has the provision to utilize the flue gas generated for preheating the input of raw materials. Various aspects of designing the furnace operation include viz. Feeding the raw material at a fixed rate, designing the crucible used for melting ilmenite, proper cooling arrangements, an innovative method for tapping the melt, recovery of heat from the gases, various safety arrangements which are some of the important milestone of the present work. The various operations have been carried out through a controller panel. Experiments were carried out to optimize various processing parameters using statistical modeling. Large scale experiments have been carried out at 10 to15 kg scale. The material balance has been calculate, and it has been observed, that about 95 percent recovery could be obtained for both Iron and Titanium oxide from ilmenite. The detailed characterization on Titania rich slag and iron has been carried out. It has also been shown that using the above slag, it is possible to prepare nanosized Titanium dioxide powder containing about 98 percent Titanium dioxide by optimizing leaching conditions. Keywords: titania rich slag, ilmenite, thermal plasma

Sep 1, 2012

By M. Kadiyski, V. Stoyanova, E. Visariev, V. Stoilov

"The present study deals with copper losses in slag from copper smelting. Copper slag cooling at Aurubis Bulgaria is traditionally done in pits. A new type of slag-cooling is introduced in the site, involving cooling ladles. In a previous study, the ladle cooling process was studied in detail, showing an improvement in the recovery of copper in the slag after flotation. The main reason for better recovery of copper is the increased cooling time, which allows for the accumulation and aggregation of copper droplets. The effects of the newly introduced slag cooling process are studied using optical microscopy and scanning electron microscopy. Cooling in pits and in ladles is compared, based on copper droplet size, distribution and content. Specialized image processing software is employed on images taken with an optical microscope. The results are then compared with a similar technique, available in SEM software. The availability of phase-analysing image software in combination with electron dispersive X-ray spectroscopy makes it possible to study the morphological properties, distribution and chemical composition of the copper droplets. The obtained results confirm the initial conclusions about size, distribution and composition of the copper-bearing particles. A large amount of copper particles is examined showing an obvious increase in their size from pit- to ladle cooling. The results show an increase in the average size of the droplets, which doubles from pit-cooling to ladle-cooling. There is a well-pronounced tendency of decrease of the percentage of droplets in the smallest fraction (<5 µm) in the ladle-cooled slag. In addition, the number of droplets in the larger fractions increases, compared to the ones in the pit-cooled slags. It is believed, that the developed methodology for analysis provides a relatively quick and reliable solution for comparison of the cooling rates in the slag. INTRODUCTION In the process of copper smelting and converting, iron-silicate slags are produced that contain various amounts of dissolved and entrained copper. Different physical and chemical techniques are employed for the valorisation of the remaining metals in the slag – magnetic separation, leaching, roasting, flotation, etc. According to Gorai et al (2003), about 2.2 tons of slag is produced per ton of metal. In 2016, about 20 million tons of copper have been produced globally (www.icsg.org). At an average of 0.5 percent copper content after treatment, these slags contain more than two hundred thousand tons of copper which is lost due to inefficient processing."

Jan 1, 2018

By B. K. Gorain

Mining of low grade deposits along with the necessity to design and operate flotation plants with high throughput presents unique metallurgical and environmental challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life of a mine. Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy, the need to use poor quality water such as brackish or sea water, reduce environmental impact from the process, integrate flotation with hydrometallurgy to maximize precious metals recovery, escalation of capital and operating costs, use of unproven technology and constant use of larger equipment, high ore variability, worldwide constraints on resource availability and an ever increasing need for reliable metallurgical input to financial models to evaluate economic viability of projects. The need to develop effective solutions to these problems in a short time frame is becoming a key to the success of any new project and for sustaining the profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial with the need for a more lateral thinking along with strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex flotation problems Keywords: mineral processing, flotation, flotation problem solving, flotation optimization, plant design, innovation

Sep 1, 2012

By A. Mainza, H. Hill, L. Bbosa

"The main objective of ore breakage characterization is to quantify the relationship between the energy supplied for breakage and the size of the resultant progeny. In this study, the ore breakage characteristics of drill core particles and crushed particles were compared. Single impact breakage tests were conducted on a basalt ore sample using the JK rotary breakage tester. The size-dependent model by Shi and Kojovic was used to fit the breakage data because the effect of initial particle size is accounted for in the model. It was found that crushed particles consistently gave a higher degree of brokenness than drill core particles and the differences were attributed to the internal structure of the particle. Drill core particles contain a lower crack density (paths of weakness) than crushed particles which have been pre-weakened during the crushing process. An increase in crack density is directly related to a decrease in the minimum threshold energy. Upon application of a stressing force above the stress threshold, particles with a higher crack density will fracture more easily because of a higher rate of crack propagation due the numerous paths of weakness available. It was therefore concluded that under the same conditions, drill core particles are more competent than crushed particles. INTRODUCTION Comminution devices have commonly been reported as being the largest energy consumers in mineral processing circuits (Napier-Munn, 2015). Cleary (1998) reported that the inefficiency of comminution devices is a result of less than 5% of the supplied energy being utilized for breakage, with the majority being expended as heat and noise. With steadily declining fossil fuel supplies and a looming global energy crisis, the mineral processing industry has increased its focus on energy reduction measures. Ore breakage characterization plays a critical role in the design and optimization of comminution circuits (Tavares and King, 1998). The main objective of ore breakage characterization is to empirically quantify the relationship between the energy supplied for breakage (specific input energy) and the size of the resultant progeny through laboratory particle breakage tests (Napier-Munn, 1996). Commonly used laboratory breakage devices include the Drop Weight Tester (DWT), Split Hopkinson Pressure Bar (SHPB) and more recently, the JK Rotary Breakage Tester (JKRBT). Typically, a standard single impact breakage test procedure consists of a matrix of experiments on particles in four to five narrow size fractions each tested at low, medium and high energy levels. The resultant progeny of each test is sized to obtain a particle size distribution (PSD) from which the degree of breakage, usually in the form of a t10 value (percentage of the progeny material that passes 1/10 of the feed size) can be obtained for each size fraction and energy level (Napier-Munn, 1996)."

Jan 1, 2018

By K-O. Mickelsson, S. Töyrä, H. Esbensen

Accurate information of physical, chemical and metallurgical quality characteristics such as moisture content, iron grade and particle size are crucial for successful process control and for producing products within customer specifications. Correct moisture content of pellet feed is an important variable for successful balling of iron ore pellets and to minimize power consumption in the sintering process. Control of the filtering process in the pelletizing plant is therefore essential for both productivity and high product quality. The current measurement systems for moisture content at LKAB are based on two types of manual grab sampling, subsequently analyzed with rapid moisture determination methods. Previous studies of the measurement systems have indicated high sampling variability resulting in lowered possibilities for successful process control. The objective of the present study is to evaluate an alternative filter sampling approach and testing of on-line Infra-Red analysis (IR-analysis). On-line IR-analysis has the advantage of eliminating physical sample extraction and allowing for continuous monitoring of moisture content. However, this approach is sensitive to the surrounding environment, making careful calibration and control crucial for the quality of measurement results. Furthermore, as IR-sensors only target the surface of the conveyed pellet feed, several incorrect sampling errors need to be considered and counteracted to eliminate sampling bias and reduce the remaining measurement variability. Variographic characterization was applied to the two current grab sampling approaches of combined filtered material, to the alternative filter sampling method, and to the On-line IR-analysis. The results indicate that both the sampling of separate filters (using composite sampling and ISO-standardized moisture analysis), as well as a calibrated and well- maintained IR-sensor can improve the relative variability significantly, by lowering the total measurement system variance from 60% to 25%.

Jan 1, 2018

Deposit of Jinbaoshan platinum group metals (PGMs) ore ranks the second in Yunnan province, China. Study on process mineralogy shows that the grade of copper and nickel in the ore is just 0.16% and 0.20% respectively. Moreover, the impurities magnesium and iron and silicon are rich in the ore. The copper and nickel sulfides in the ore, especially the minerals of PGMs, are finely disseminated with the gangues like serpentine. Fine grinding is necessary, and high content of MgO in the concentrate is inevitable through traditional flotation technology on the basis of process mineralogy studies. Achievements on process mineralogy studies are applied to guide the flotation tests successfully. Progress on flotation has been made through comprehensive studies. Suitable grinding by two stages is required for the finely disseminated PGM sulphide ore to achieve the liberation of valuable minerals. Stage grinding and stage separation shall be conducted for a better recovery of valuable minerals. The oxidation state of mineral surface of sulphides has a profound effect on flotation of the ultra-fine sulphides, especially the pentlandite. The combined use of collectors enhances the selective collecting on the ultra-fine and low-grade valuable minerals, is of critical importance.

Jan 1, 2014

By P. Condori

In spite of the importance of the slurry transport and discharge in autogenous and semiautogen-ous (AG/SAG) mills, it is evident that a more comprehensive and useful model is still required. Semi-empirical models used up to now have many limitations and cannot be used beyond the ranges in which they were developed. The breakage of particles as they are transported along a mill com-plicates the experimental analysis and the modelling of the transport process within the mill. The interaction of the grate discharge and the pulp lifters, with the added issue of backflow from the pulp chamber into the mill, makes the discharge modelling process difficult. In order to overcome these difficulties, a mechanistic approach has been applied. The general transport and discharge model was subdivided into four independent models: Flow through the charge, flow through the grate, flow in the pulp lifter, and flow-back. This paper gives an overall description of the modelling approach and discusses in particular the modelling of transport of fluids through the charge. In order to evaluate and calibrate the model, experimental work was carried out. To evaluate the gradient pressure under different conditions of charge packing and flow rate, a specialised experimental rig with a highly sensitive pressure gauge was used. Preliminary results identify the differences of the charge and grate on the restriction of flow. The existence of a dynamic voidage in our particular system was more evident and as a result, a semi-empirical correlation for the voidage was developed. In general, results show that the me-chanistic model derived from Ergun?s equation for flow through a packed bed can be satisfactorily adapted.

Jan 1, 2014

By Chris A. Fleming

"The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative.There is arguably an even more compelling reason for mining companies to consider cyanide recycling. With the growing storm of negative public opinion that the use of cyanide in the mining industry is attracting - following several highly publicized spills over the last couple of years - the time has come for the gold industry to demonstrate environmental diligence and stewardship in the use of this commodity that is so vital for their industry. There is no doubt that the widespread implementation of cyanide recycling will reduce the impact of the cyanidation process on the environment, both by reducing the risk of spills (with less cyanide being transported from manufacturing plants to gold mines), and by reducing the loading of toxic and nontoxic metals and ions in the tailings.This paper briefly discusses the pros and cons of the different processes that are available for the treatment of gold plant tailings to regenerate and recovery cyanide for recycling, and presents a techno-economic argument for the incorporation of this technology into many gold plant flowsheets today."

Jan 1, 2003

By L. Z. Li

The application of some environment-friendly mineral processing technology was introduced in Xitieshan lead?zinc mine and Hugary copper mine of China Western Mining Co., Ltd, located in western plateau area where the ecological environment is extremely fragile. The results of the significant economic efficiency were obtained by applying these new techniques while the protection of peripheral environment and the improvement of ecology were made.

Jan 1, 2014

By M. Chettibi

The interaction and galena flotation with xanthenes and dexanthogen regularities have been de-fined. So, using thermodynamic method of analysis, the thermodynamic stability of [galena - xanthenes - water] system and the behavior of lead xanthenes surface state in solution were devised. Thus, results of cared out calculations and experimental investigation completely coincide with-out depending on witch product of sulfur oxidation is formed in the solution. In additional, was obtained quantitative physico-chemical models for the necessary xanthenes concentration of lead sul-fide complete flotation in the tuning fork of: at ?? values from 7.0 up to 9.0 (or at the formation of lead carbonate PbCO3 ) and at ?? values from 9.0 up to 12 (or at the formation of lead hydro carbonate Pb3(OH)2(CO3)2 Physico-chemical models derived can be used as the criteria for functional units of automation systems to control and regulate the flotation process in mineral processing plants.

Jan 1, 2014

By L. A. Vaisberg

"Mining processing plants are the most high-performing industrial enterprises in the world economy system. Even at an average-scale mining enterprise, the grain-size separation equipment continuously processes 105 to 106 dissimilar mineral particles per hour. In separation by physical properties, their number increases by at least 10 to 50 times. Mathematical modeling of such a high flow of discrete particles is carried out using two different approaches: the discrete-particle and the phenomenological methods. The calculations demonstrate the possibility of handling big data when describing the processes of separation of granular material. INTRODUCTION The interest to the screening process and the process of formation of new screen designs in Mekhanobr is traditional since the moment of its foundation. It is symbolical that the first publication of the Mekhanobr proceedings in 1924 was the monograph dedicated to screens and screening products as such, which was the first one in the world at that moment. It was a book of Prof. L. B. Levenson, one of the founders of Mekhanobr, who headed the Technical Bureau of the Institute. Vibratory screening is the most mass process in the technologies of solid minerals processing, which determines significantly the energy demands of crushing and grinding cycles, and at some enterprises determines the quality of the final product, for example in case of crushed stone, coal or abrasive materials production. The general understanding and simulation of the process of poly-dispersed granular materials vibratory screening was developed at several conceptual levels taking into account the features of classification of materials with different size and density.Considering the real industrial processes of vibration screening, it shall be noted that at the sieve surface of the screen in the initial part of the deck the classification in a thick material layer (in natural conditions) occurs, which further transfers to a thin layer (free movement). In the process of screening of light minerals, for example coal or metallurgic feedstock, screening is mainly performed in the thick layer."

Jan 1, 2018