Search Documents

By Yi-jun Cao, Jin-cai Ran, Guo-sheng Li, Jiong-tian Liu, Li-jun Deng, Shu-lei Li

A fly ash sample from a power station in Guangdong province has been characterized by size separation, X-ray diffraction, contact angle measurements and X-ray Fluorescence. The ash sample had a loss-on-ignition (LOI) (%) of 15.54% and a large proportion of the unburned carbon was distributed in the +74 µm and -20 µm fractions. Contact angle measurements suggested that the removal of unburned carbon from the fly ash using flotation would present some challenges. The effects of various operating variables on the removal rate of unburned carbon (RUC) (%) and (LOI) (%) were determined using a cyclonic-static micro bubble flotation column (FCSMC). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil (frother) dosage was 600 g/t, pulp density was 20%, superficial gas velocity was 1.4 cm/s and circulating pressure was 0.20Mpa. Column flotation tests indicated that the FCSMC method a viable and effective separation process for removing the unburned carbon from the fly ash. Under the optimized conditions, a clean ash with 2.13% LOI and 94.21% RUC was obtained.

Jan 1, 2014

By David Morrow

Fly ash is a by-product from coal-fired power stations that is captured from the exhaust gas stream by electrostatic precipitators (ESPs) or bag houses. It is mainly derived from the inorganic components in coal but also contains residual carbon from unburnt fuel (measured as LOI). In the past, nearly all fly ash was sent to landfills or tailings ponds by power generators but this trend is quickly changing due to landfill costs, sustainability requirements and the inherent value in correctly processed fly ash. The main property that makes fly ash suitable for recycling is its use as a pozzolan. Pozzolans exhibit cementitious properties that make them suitable for partial cement replacement, and that can have beneficial properties for concrete mix designs. Fly ash can be used to replace up to a third of the of the Ordinary Portland Cement (OPC) requirement. Suitable fly ash nearly always requires the removal of the less reactive coarser fraction from the finer fraction. Due to the pozzolanic nature of fly ash, it must be processed dry and separation is normally required at 45 micron. In response to the increasing demand from a range of dry classification applications, Metso purchased an established air classification technology suitable for both mining and construction applications. The classifiers intelligent design efficiently utilizes the air flow which keeps power requirements low whilst including a scrubbing/recirculating function within the classifier that allows extremely efficient separations even at very fine sizes. This technology is of global interest to Fly Ash processors, but should be of particular interest in India which is both the second largest cement producer in the world as well as producing 80% of its power from thermal sources. This paper is intended to give a brief overview of fly ash and requirements for use as a pozzolan, air classification of fly ash and a case study from an established and experienced fly ash producer. Keywords: air classifier, fly ash, pozzolan, fineness, cement, cholla, salt river materials group

Sep 1, 2012

By N. Syna

The selection and preparation of activated carbon suitable for specific application can often involve exhaustive adsorbent preparation and testing. This work examined an emerging technique based on modelling the correlation of observed adsorption capacity to the carbon characteristics as a means of decoupling the roles of carbon textural and surface chemical properties. The insights to these specific roles are then used in tailor-making adsorbents and in establishing the optimal carbon properties for specific application. In this study, a series of activated carbons prepared from bagasse by physical and chemical techniques and commercially available carbons were used in developing the models. These carbons were tested for the adsorption of thiourea-gold (I) chloride complexes. Thiourea is an important alternative gold lixiviant with the potential to address current ecological and safety concerns in the extraction of gold. A four-component model, which correlated the adsorption gold capacity to carbon textural and surface chemical properties, was proposed. The model fit was assessed using multi-linear regression and a partial F-test. This was followed by goodness of fit test achieved through r2, adjusted?r2 and mean square error (MSE) values. The results suggest the adsorption of the gold-thiourea complex is strongly influenced by the internal surface area and pH of the carbon. Tailor-made activated carbon from bagasse showed adsorption gold capacities of up to 198 mgAu/g adsorbent, demonstrating the potential of bagasse as a precursor for gold adsorbents and of this empirical modelling approach in developing adsorbents for metal recovery.

Jan 1, 2014

By Vladko Panayotov, Marinela Panayotova

"Recently, in order to extract metals, the industry is trying to process old metallurgical slag. The material requires very fine grinding that results in enhanced slime-formation. This in turn leads to problems in the course of the flotation process and to a loss of metal. In addition, it causes difficulties in the wastewater treatment aimed at water reuse. The aggregation and separation of the fine particles and their further subjecting to mineral processing would result in more efficient use of raw materials. Closing the water cycle also would be facilitated. The paper presents results from studying sixteen flocculation reagents, commercially available for treating municipal wastewater, including products based on nanotechnology, for their ability to rend the production wastewater in suitable for reuse in the flotation. It turned out that, from all studied reagents, the cationic C-587 is suitable for the purpose. Some of reagents were studied for their ability to flocculate selectively, in presence of coke fines, rich in copper fines which are produced at grinding of a slag from lead-zinc metallurgy. Most promising reagents are chosen, based on the chemical analysis of the flocculated materials. Open-cycle rough copper flotation experiments with the flocculated fines and recycled wastewater gave encouraging results."

Jan 1, 2014

By Longjiang Li, Mao Jiang, Zhihui Shen, Guizhou University, Yin Pan

This paper aims to study the influence and action mechanism of collector Y-89 on the flotation of auriferous pyrite. The measurement to identify adsorption quantity, IR and XPS spectrum analysis and flotation experiment made on the pure mineral were conducted. The research results show that when the dosage of MIBC is 20 mg/L, and pH of 8, the dosage of Y-89 over 60 mg/L, the pyrite recovery rate is greater than 80%.And when the dosage of Y-89is 60 mg/L, dosage of MIBC 20 mg/L, the pH in a wider range (pH=4~9), the recovery is greater than 75%. When the pH is above 10, the pyrite is depressed and its recovery rate is found to be dramatically dropping. Adsorption quantity measurement also shows that the strong alkaline conditions inhibit the adsorption of Y-89 on the surface of auriferous pyrite. IR measurement indicates that chemisorption of Y-89 occurs on the surface of auriferous pyrite. XPS spectrum analysis indicates that without adding Y-89, oxidation reaction occurs on the surface of pyrite. But when Y-89 is added, the chemical environment of Fe on the surface of pyrite has changed. Such findings indicate that with Y-89, chemisorption occurs on the surface of auriferous pyrite.

Jan 1, 2014

By Jurgens J. Louw, Vincent C. Smith, Gareth C. Smith, Agit Singh, Dave G. Hulbert

"The flexibility of the PlantStar control platform has enabled Mintek to investigate and easily develop new control strategies for both milling and flotation. This includes a Solids Feed Controller, a Safety Limit Controller, Mill Power Optimiser and Flotation Optimiser, amongst others.The solids feed controller was developed for minerals processing plants using a specialised time delay compensator. Using conventional time delay compensators that are purely model based, results in robustness problems due to model uncertainties. The Mintek Solid Feeds Controller makes use of a plant model, but compensates for model inaccuracies, giving more controller stability and a more robust delay compensation algorithm.The safety limit controller has been developed to switch smoothly between normal and safety control loops without bumping the process. The safety loop output is chosen in accordance with a predefined list of priorities and whether the respective constraint boundaries are exceeded.The Mill Power Optimiser helps to find the power peak on the mill power curve. This insures maximum grind with maximum throughput. It also prevents power dips due to mill overloads, making the milling circuit easier to operate.The flotation optimiser algorithm analyses trends of all accessible variables in the process. The algorithm uses this information to calculate operating conditions that will control the residence times, mass pulls and circulating loads within a flotation circuit to a specified setpoint. Research is being done to now optimise these setpoints in order to achieve better recovery."

Jan 1, 2003

By M. M. Yahyaei

The Sarcheshmeh new concentration plant uses a 32 ft×16 ft constant speed (10.5 RPM) SAG mill with two 5500 hp motors which could rotate in two directions. The mill liners are chrome-molybdenum steel casting type with a Brinnell hardness between 325 and 375 with the lifter face angle of 14° and lifter height of 152 mm. The shell liner consists of 120 (two 60 rows) pieces with a High-High configuration in a rail design. A specially designed liner wear profile measuring device enabled fast and accurate measurements inside the mill during the mill shut-down periods. The measurements indicated that the liner wear profile along the liner length is non-uniform and the highest wear occurs between 1.25m and 2.75m of the mill length. The average weight of liners at the time of removal was 47% of the original weight indicating a significant metal loss. The modification of liner shape was undertaken with the aim of having a uniform profile at the liner removal time. The proposed liner unlike the pervious type did not have a uniform shape with a lifter height of 187mm at the section where the wear rate was high. It was believed that this new profile could arrive at a uniform profile at the liner change out time. A study was also directed to the possible change of charge motion due to the liner profile modification. The dynamic behaviour of charge was investigated through the analysis of forces acting on a single ball using mill characteristics such as mill diameter, rotational speed, lifter height and release angle. The simulation of charge motion with this method and Milltraj TM software indicated that the impact position of charge will change only one degree due to the maximum increase of 35 mm in the lifter height. This assured that the installation of the modified liner would not have any adverse effect on the mill because of ball impacting the mill shell. It was predicated that the amount of scrap metal will reduce to 30% from the current value of 47% beside 1500 h increase in the liner life time.

Jan 1, 2014

By A. Gül

This investigation was carried out with low grade Murgul-Cakmakkaya copper ore once used to be dumped away as waste material. Sulphide minerals in the ore sample observed are chalcopyrite, pyrite, sphalerite and to some extent molibdenite; quartz, calcite and dolomite are the gangue minerals. The ore sample assays 0.28% Cu, 2.94% Fe and 3.36% S. Mineralogical study of the ore sample showed that adequate liberation of chalcopyrite for flota-tion was achieved below 100 µm. In flotation tests Aerophine 3418-A was the collector employed, NaOH or Ca(OH)2were the pH modifiers. Deactivators used were sodium meta bi-sulphide, starch, dextrin and lime. MIBC was the frother used throughout the tests. Test results showed that starch alone was the most suitable depressant to give the optimum metal content and recovery val-ues. Activated charcoal was used to adsorb excess collector species in the flotation pulp during cleaning stages After two stages cleaning of the rougher concentrate using starch as the depressant a copper concentrate assaying 21.2% Cu was obtained with 79.5% recovery while the tailings contained 0.01% Cu and metal losses were about 3%

Jan 1, 2014

By M. Zolghadri

MIBC and sodium metasilicate are used as a frother and a dispersant in coal flotation respectively. In order to study interaction between them, flotation experiments were performed on fine coal (<150 microns). It was found that if the frother (MIBC) dosage is in excess of a certain limit, it has an activation effect on the gangue minerals associated with coal. In addition, it was found that however sodium metasilicate can disperse clay slimes eliminating slime coating, but in the case of excess dosage, could intensify activation effect of MIBC, which is undesirable in coal flotation. Keywords: coal flotation, sodium silicate, frother, dispersion, activation

Sep 1, 2012

By S. Q. Zhu

A newly developed coal flotation collector ZFC and its flotation characteristics for five different coals were introduced in this paper. ZFC is an emulsion composed of 27% diesel oil, 70% water and 3% surfactants. The main surfactant is synthesized with oil which is environmental favorable and reproducible. Compared flotation experiments show that, at the same dosage, ZFC give 2%~5% recovery promotion than typical collector with only a slightly ash content increment, but saving 70% diesel oil. Zeta-potential and Wetting heat measurement indicate that the surfactant helps the interactions between oil and coal particles, the industrial application tests in several coal preparation plants demonstrate that ZFC is suitable both in technical and economical aspects.

Jan 1, 2014

By R. Batterham

"The history of mineral processing is indeed long and has always been tied to mining methods of the day. While many new processes and devices have been developed, the most significant trend in recent times has been the ever increasing scale of operations. There is serious doubt this ongoing trend is enough to match the global trend of falling grades and rising energy demands needed for mineral processing. As well we see that globally, the social licence to operate for mining (and hence mineral processing) is far from secure. Indeed, some argue that mining as we know it is dying and in the future, mining will be much more environmentally secure, even to the extent of insisting upon “in place” recovery and only bringing to the surface the valued product. In this paper we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10 - 20 years but in the meantime, the focus is just as likely to be on removal of waste much earlier in circuits. Either way, mineral processing as we know it will change significantly. INTRODUCTION Mineral processing has a long history well covered in a recent publication (Habashi, 2006) who points out “the ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result, all efforts were made to enrich the gold by washing away the light gangue minerals. Similarly, another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. Since the middle ages, striving for improved economics has driven a string of innovative developments in milling and separation. The reader is again referred to the informative and illustrative text by Habashi."

Jan 1, 2018

In this paper High Pressure Grinding Rolls(HPGR) was utilized to pretreat CVRD southern specular hematite for enhancing the pelletization of the refractory hematite. The process parameters of HPGR, balling and firing were optimized, and the mechanism of HPGR was demonstrated by determining the surface activity by means of Blaine specific surface area tester, laser size analysis, scanning electron microscopy (SEM),X-ray diffraction (XRD), micro calorimeter and pelletability index. It is shown that the pelletization of the refractory hematite was greatly improved. The drop strength of green balls increases from 3.4 times to 13.6 times from 0.5m height while the bentonite dosage decreases from 2.2% to 1.3%.The compressive strength of roasted pellets also reaches 2500N/pellet. The mechanism of the pretreatment of CVRD southern specular hematite concentrates by HPGR is revealed that the surface activity is improved by an increases in specific surface area and the amount of micron size fractions, and higher lattice deformation and defects due to the fractures occurring inside particles during static pressure comminution, resulting in more wetting enthalpy, higher pelletability index and good property of roasting.

Jan 1, 2014

By S. Mohanta

In composite washeries optimization of operating parameters to achieve maximum clean coal yield at the desired clean coal ash level is a major problem. This problem is more acute in countries like India, which have predominant reserves of difficult-to-wash coals. The constrained operational parameters of washing for some equipments make it more severe. In addition to this, the dependence of separating performance of different equipments upon various variables aggravates the situation. Here an attempt is made to find a numerical solution to get maximum yield and minimize the difference between the actual and the theoretical yield. The solution is arrived through constrained non-linear optimization of a multivariable objective function that utilizes spreadsheet tools; the method accommodates any number of source coals or washing size fractions. By using a designed Ep value the predicted yield of composite clean coal has been calculated and the yield is optimized subject to constraints on both the ash and specific gravity. It is shown that operational constraints of different washeries in the composite plant that utilizes gravity separation methods can also be over-come. The technique offers the coal preparation engineer an effective and straightforward method for determining the optimum cut-points of separation for different coals or blended coals to obtain maximum product yield at a specified level of ash content.

Jan 1, 2014

By E. V. Koporulina, I. Zh. Bunin, M. V. Ryazantseva

"We studied the mechanism of structural and chemical transformations of columbite, tantalite, zircon and feldspar surface during the treatment by high – power electromagnetic pulses (HPEMP) using the methods of X - ray photoelectron spectroscopy (XPS), analytical electron microscopy (SEM - EDX), Kelvin probe force microscopy and flotation experiments. According to XPS and SEM - EDX data, major changes in the atoms chemical state of investigated minerals surface are related with formation and modification of functional cover and changing in concentration (% at.) of hydroxyl groups on the mineral surface, leading to increase in the contrast of technological properties of the rare metals minerals. Research has identified the optimal parameters of HPEMP - treatment of rare - earth minerals Npuls ??104, Ttreatment ??100 sec. improving the selectivity of the flotation separation of columbite and zircon. The difference in mineral recovery into the froth (? e) before and after HPEMP - treatment was about 11 % and 24.5 %, respectively. No significant increase was observed in the flotation activity of feldspar. This study's findings demonstrate the effectiveness of HPEMP - treatment in inducing a controlled change in the structural and chemical properties of rare - earth minerals and improving the process efficiency for the processing of rougher tantalum - niobium gravity concentrates.INTRODUCTIONThe importance of improving the processing methods of tantalum-niobium ores and concentrates is explained by the mineralogical properties of rare - earth ores. These are properties such as the variable mineral, chemical, and grain size composition, complex morphometric properties, and the dissemination of ore mineral grains of micro - and nanometric size. Iron oxide and hydroxide films on the mineral surfaces neutralize the surface physicochemical and absorption properties of the minerals. Both in Russia and globally, nonconventional (non - mechanical) methods are being developed based on physicochemical, electrochemical, and pulsed energy impacts to improve the efficiency of disintegration and liberation processes of disseminated mineral complexes and to enhance the contrast of the structural, chemical, and technological (floatability) properties of refractory ores. This study is devoted to the investigation of the applicability of high – power electromagnetic pulses (HPEMP – treatment) for the change in the structural and chemical properties of rare - earth minerals and improving of the flotation properties contrast."

Jan 1, 2018

By Q. Shi

An investigation into the hydrophobic aggregation of ultrafine smithsonite in surfactant solution has been undertaken through a combination of hydrophobic flocculation experiments, zeta potential measurements, surface tension measurements, and contact angle measurements. The experimental results have revealed that the behaviors of hydrophobic aggregation were closely correlated with the particle hydrophobicity, but they were not lowered byte change of the particle surface charges due to surfactants adsorption. On the other hand, the liquid (solution) surface tension (?LV) plays an important role in hydrophobic aggregation, and the hydrophobic aggregation could not occur below the critical liquid (solution) surface tension (?c). Meanwhile, this flocculation has been observed to require sufficient stirring strength and magnitudes of kinetic energy input to achieve the maximum aggregation degree. From the microflotation results, it has been found that the flotation kinetics response of smithsonite fines is markedly improved due to sufficient stirring strength, and the stirring strength influenced the floc flotation in a manner quite similar to their influence on the hydrophobic aggregation, suggesting that the formation of hydrophobic flocs is a promising means to recover smithsonite in the fine size range.

Sep 1, 2012

The traditional technological flow sheets for processing of ferrous quartzite (magnetite ores) al-low production of the iron concentrates with Fe content of 65%~68 % and recovery level about 55 %. The losses of iron with the tails of wet magnetic separation are related to hematite and quartz-magnetite particles, which are not extracted under low magnetic field employed. This work presents the results of the application of reverse cationic flotation for production of hematite concentrates with weak silica content from the tailings of wet magnetic separation of mag-netite. Fine particle size, complex mineralogy and presence of locked particles determine the impos-sibility of direct production of hematite concentrate by flotation or magnetic separation. The gravity concentration allows obtaining of iron concentrate from the well-prepared feed (size fraction -53+20 µm) but with very low recovery. Thus, hematite concentrates with weak silica content and satisfactory iron recovery were obtained by reverse cationic flotation, when it was fed with iron pre-concentrate produced by high gradient magnetic separation. The best flotation results were obtained by the use of formulations based on amines of different molecular structure that modulate the structure of adsorption layer, and favour a shifting of hydro-philic-hydrophobic balance on the surface of silicates with adsorbed starch and their preferential transfer into the froth product.

Jan 1, 2014

By E. V. Koporulina, I. Zh. Bunin, M. V. Ryazantseva

"We studied the mechanism of structural and chemical transformations of columbite, tantalite, zircon and feldspar surface during the treatment by high – power electromagnetic pulses (HPEMP) using the methods of X - ray photoelectron spectroscopy (XPS), analytical electron microscopy (SEM - EDX), Kelvin probe force microscopy and flotation experiments. According to XPS and SEM - EDX data, major changes in the atoms chemical state of investigated minerals surface are related with formation and modification of functional cover and changing in concentration (% at.) of hydroxyl groups on the mineral surface, leading to increase in the contrast of technological properties of the rare metals minerals. Research has identified the optimal parameters of HPEMP - treatment of rare - earth minerals Npuls ? 104, Ttreatment ? 100 sec. improving the selectivity of the flotation separation of columbite and zircon. The difference in mineral recovery into the froth (? e) before and after HPEMP - treatment was about 11 % and 24.5 %, respectively. No significant increase was observed in the flotation activity of feldspar. This study's findings demonstrate the effectiveness of HPEMP - treatment in inducing a controlled change in the structural and chemical properties of rare - earth minerals and improving the process efficiency for the processing of rougher tantalum - niobium gravity concentrates.INTRODUCTIONThe importance of improving the processing methods of tantalum-niobium ores and concentrates is explained by the mineralogical properties of rare - earth ores. These are properties such as the variable mineral, chemical, and grain size composition, complex morphometric properties, and the dissemination of ore mineral grains of micro - and nanometric size. Iron oxide and hydroxide films on the mineral surfaces neutralize the surface physicochemical and absorption properties of the minerals. Both in Russia and globally, nonconventional (non - mechanical) methods are being developed based on physicochemical, electrochemical, and pulsed energy impacts to improve the efficiency of disintegration and liberation processes of disseminated mineral complexes and to enhance the contrast of the structural, chemical, and technological (floatability) properties of refractory ores. This study is devoted to the investigation of the applicability of high – power electromagnetic pulses (HPEMP – treatment) for the change in the structural and chemical properties of rare - earth minerals and improving of the flotation properties contrast."

Jan 1, 2018

By N. I. Tyushkova

This is a brief survey of the technological solutions for deep cleaning of baddeleyite?s concen-trate. Baddeleyite is part of kamaphorite of composite apatite-magnetite ore in alkaline-ultrabasic mountain range of Kola Peninsula. Baddeleyite?s concentrate, which is being produced by Kovdorsky GOK (ore mining and processing enterprise) contains 97.5%~98.5% (Zr?2 + ?f?2) and also scandium oxide (0.05%). It is usually used without any chemical processing. World demand for zirconium oxide is constantly on the rise. Its consumption grows in ceramic industry and in high-tech spheres. That?s why the demand for its purity is very important nowadays (additional cleaning from phosphorus, silicon, iron, aluminium). The mechanism and kinetics of interaction of activated bad-deleyite with sulphuric acid has been studied as well. While applying method of mathematical mod-eling it was confirmed that the mechanical activation is effective for the intensification of sulphation process of baddeleyite?s concentrate with the aim of purifying it from dirt. The use of the calculated optimal regimes allows to reduce such technological operation factors as: temperature, the du-ration of process, the sulphuric acid consumption. It also allows to determine the conditions of anticipatory abstraction of scandium and main dirt in solution in comparison with zirconium oxide.

Jan 1, 2014

By Claudio L. Schneider, Peter R. King, Reiner Neumann

"Predicting the liberation spectra that are produced from breakage of two-phase ores under the random fracture assumption can be accomplished by measuring the conditional, on length, linear grade distribution directly from images obtained from a representative sample of the unbroken texture. The technique tremendously simplifies the prediction problem by avoiding the multiple convolutions that arise from the traditional method based on a description of texture from a measurement of the chord length distributions associated with each phase in the unbroken texture. For a 3-phase system, the phase transition probabilities associated with the textural information make the traditional calculation an almost insurmountable mathematical problem. The direct measurement procedure on the other hand can be expanded to three phases comparatively easily.A coal sample is used here to demonstrate the procedure. It is concluded that the conditional, on length, linear grade distribution can be predicted in the same fashion for multi-phase systems. Accurate stereological conversion is the practical hurdle to be overcome for multi-phase systems, but it is already a reality for 3- phase systems."

Jan 1, 2003

By C. Dorfling, C. A. Snyders

South Africa has extensive mineral processing and extractive metallurgy capacity and infrastructure for metal production from natural resources. Decreasing ore grades, increasing labor costs, and more stringent legislation have made economic metal production from primary resources challenging. Opportunities exist for metal production from secondary resources such as mining wastes and end-of-life consumer goods. The objectives of this study were to evaluate the current status of metal production from secondary resources in South Africa and to identify potential opportunities for further development. Two main classes of secondary resources, namely mining waste and electronic waste, were considered. Primary metal producers are dominating metal production from mining wastes; several of the gold, platinum and chrome producers operate low risk and low cost tailings retreatment facilities that contribute significantly to their overall production. Further opportunities exist in, for example, the treatment of more than 450 estimated gold tailings dumps in Gauteng, as well as metal recovery from slags and furnace dust. The majority of companies involved with electronic waste recycling in South Africa focus on collecting and disassembling; only a few perform preliminary physical processing, with the recovered fractions then being sent overseas for metal recovery. Projections are that the rate of waste generation will increase significantly and that treatment will become critical to comply with more stringent environmental legislation. Projects related to process development, techno-economic evaluations and environmental impact studies for metal recovery from batteries, printed circuit boards, and fluorescent lamps are underway. South Africa is ideally positioned to further explore opportunities for synergistic relations between metal recyclers and primary metal producers. Processing of electronic waste for production of technology metals, for which limited natural resources exist in South Africa, would be a key enabler for local manufacturing industries and expansion of the value chain.

Jan 1, 2018