Search Documents

By P. Hatefi, O. Rahmani, M. Noor-Mohammadi, A. Tohry

"Depressants play an important role in the selective separation of impurities from iron minerals by direct or inverse flotation. In this paper, sodium co-silicate (SCS) with chemical formula of Na4SiCO6, as a depressant with pH modifier features, has been synthesized and used for phosphorus bearing iron ore in anionic reverse flotation. In this process, phosphorus is floated while the iron oxides are depressed, using fatty acids as collector in an alkaline medium. Batch and pilot flotation tests were carried out to investigate the influence of SCS on the separation selectivity of phosphorus from iron oxides. Also the depression mechanism of SCS on hematite surface was investigated by microflotation tests and FTIR spectroscopy measurements. The flotation results indicated that without using a pH modifier, the pH of pulp could reach up to 10, when SCS was used as depressant. In this condition, a better depression performance was observed compared to sodium silicate (SS). Using the SCS, phosphorus and total iron content in iron concentrate was 0.046% and 66.29%, respectively, compared to SS where these values were 0.06% and 65.75%, respectively. As a result the weight recovery of iron concentrate was increase by around 4%, compare to SS. It was also found that 238 g/t of SCS could be used instead of 3 types of reagents collectively, including 32 g/t of NaOH, 151 g/t of Na2CO3 and 400 g/t of SS gel.INTRODUCTIONThe phosphorous presents in iron ore minerals is mainly in the form apatite mineral. The apatite is separated from iron ore minerals by magnetic and flotation methods (Ma, 2012). The reverse anionic flotation of iron is one of the most common method for removing phosphorus from iron concentrate (Araujo et al., 2005).Usually apatite minerals are readily floated using anionic collectors such as fatty acids (Ma, 2012). In this conditions the iron minerals are depressed and by modifying the pH in alkaline conditions, selective separation of phosphorus from iron concentrate can be achieved. Depressants including; sodium silicate (SS), starch, dextrin, guar gum and humic acids play an important role in the reverse flotation of iron ore (Kar et al., 2013; Ma, 2012; Turrer and Peres, 2010; Araujo et al., 2005). Studies have shown that SS has a better effect on iron recovery and phosphorous reduction, compared with other depressants (Tohry and Dehghani, 2016; Qi et al., 1992, Dho and Iwasaki, 1990). In most flotation processes, modifiers are used to adjust the pH. To achieve alkaline conditions, mainly pH modifiers such as carbon dioxide and sodium carbonate are used."

Jan 1, 2018

By B. Rai

Processing of dolomitic phosphate ores remains one of the most challenging problems in phosphate ore beneficiation. The beneficiation plant at Jhamarkotra in Rajasthan, India for example is currently using a conventional double stage flotation process which involves first a fatty acids flotation to produce a combined dolomite-apatite concentrate (bulk concentrate) from associated silicate gangue. Dolomite is then separated from this bulk concentrate by flotation with fatty acids collectors and depressing apatite with phosphoric acid and sulphuric acid. This process requires addition of large dosages of reagents (H3PO4 and H2SO4) to depress apatite and to maintain highly acidic pH during flotation. Furthermore several cleaning and scavenging stages are needed to obtain the product of desired quality. We have developed and employed a molecular modelling based methodology of designing selective reagents for apatite-dolomite separation. We have been able to take into ac-count the differences in the distribution of calcium cations on these two surfaces in our design and hence develop novel phosphonic acid based depressants for apatite-dolomite separation with con-ventional fatty acids as flotation collectors. We have demonstrated the utility and power of molecular modelling based reagents design approach through this work on beneficiation of Jhamarkotra dolomitic phosphate ore using our novel phosphonic acids based depressants at pH?s close to natural pH. It was possible to reduce the MgO content of the ore from as high as 13.3 % to 1.5% in a single stage flotation. Our flotation separation results on Jhamarkotra ore with these new phosphonic acids based tailor-made depressants for apatite-dolomite flotation separation are discussed in this paper along with results of corresponding molecular modelling computations on the same system.

Jan 1, 2014

By Victor V. Karmazin

"The appearance of the precise equipment for analysis of results of the laboratory tests with using of the computer processing allows raising accuracy of the estimation of the expected indexes of the mineral processing. Certainly, laboratory tests will not be able to substitute completely industrial ones, but allow reducing the amounts of the industrial tests, that vastly reduces the cost of technological forecast and preparation of data for projection.Calculation of the potential indexes of mineral technology (mass yields and the metal content in products) is fulfilled on the base of results of measurements of the mineralogical liberation parameters using special formulas.The quality of the concentrate ßc = a + ?l • ?s • ?i (ßt - a) can be achieved on a level of the theoretical metal content of a mineral - ßt only if coefficients of mineral processing, of liberation ?l and selectivity ?s of grinding, effectiveness of separation, will reach 1 (a - metal content of the row ore).Increase ?l by overgrinding automatically decrease ?s, and only by destroying of particles of ore along surfaces of accreting of minerals (?i = 1) and when values of all three coefficients will aim to 1, then ßc ? ßt.The degree of liberation of the useful mineral is the ratio of mass of free grains of the useful mineral in the product to general mass of the same mineral in this product. The factor of the liberation, which is defined by curves of dressability by angle of slop of the curve of the elementary faction - ?, is Kr=1 – tga. Kr changes from 0 to 1 when a changes from 45o to 0o. The liberation is reached by grinding of the material, although degree of the liberation, as a rule, is lower than the degree of the grinding."

Jan 1, 2003

By I. Yu. Rasskazov, A. V. Rasskazova, N. M. Litvinova, N. A. Lavrik, V. G. Kryukov

The possibility of the intensification of the gravity processing of complex iron-manganese ore, which contains the finely dispersed inclusions of gold and platinum is shown. Clear mineral fractions of precious metals were sorted out of the different types of ores (quartz-braunite and carbonate- magnetite ore, ferruginous quartzite, carbon-containing shale, breccia-limestone and dolomite breccia). Composition and structures of precious-metals particles was detailed. The industrial content of platinum and gold was found. Precious-metals mineralization is character for all types of ores. High content of platinum is indicated in the carbonate-magnetite (up to 11.3 mg/kg) and quartz –braunite (up to 10 mg/kg) types of ore. Gold is presented in the ferruginous quartzite (up to 1.29 mg/kg) according to the data of the reduced mineralogical analysis. The composition of native platinum depends on the type of the ores: 1) quartz-braunite type contains isoferroplatinum (Pt3Fe) with Cu, Rh, Ir, Ru; 2) carbonate-magnetite type contains isoferroplatinum with Cu, Sn, Ni, Rh, Ir, Os; 3) pyritic-carbon ore contains isoferroplatinum with Sn, Ni; 4) ferruginous quartzite contains isoferroplatinum without admixtures. The ultrasonic treatment of mineral aggregates (P = 41.5 Watt, I = 15 W/cm2) made possible the liberation of fine particles of precious metals. Smooth-shaped or crystalline mineral aggregates are effectively liberated after acoustic treatment. Their surface is freed from impurities. The aggregates with the complex form and structure, which consist of the numerous plates and the grains, are not effectively liberated from impurities. It is shown that the ultrasonic treatment of aggregates with the fine inclusions of precious metals contributes to the liberation of the particles of platinum and gold and intensification of the gravity processing of refractory ore. This approach contributes the increase of the raw-material base of precious metals.

Jan 1, 2018

By Gaom M. W.

The Mount Isa copper concentrator started operation in 1973. Its secondary grinding circuit consisted of two 5 meters diameter ball mills in closed circuit with 505 mm cyclones. At the design throughput of 800 t/h, the 80% passing size of the circuit product (P80) was about 140 µm. The then Mount Isa Mines Limited (?MIM?) installed two autogenous grinding (?AG?) mills in 1991 to replace two stages of crushing, a rod milling stage and one primary ball milling stage. One of the AG mills was later converted to semi-autogenous grinding (?SAG?) operation by the addition of a steel grinding medium to achieve the designed plant throughput of 800 t/h. The cyclone over-flow P80of the secondary ball mill circuit was reduced to 120 µm by the increased operating power in the AG/SAG mill circuits. The two secondary balls mills had a grinding power of 5.2 MW. A mineralogical study of the milled products indicated that half of this grinding power was sufficient for adequate chalcopyrite liberation. Eliminating one of the secondary ball mills could reduce energy and operating costs by more than A$2 million dollars per year. An optimisation project team was established to achieve the predicted power saving. Grinding circuit simulations were conducted for different circuit configurations. Ball mill parameters such as ball size, ball charge and feed slurry density were optimised. Cyclone body diameter, spigot and vortex finder sizes, and cyclone types were tested. The secondary ball mill circuit was redesigned and several proposed circuits were run as trial production campaigns to determine their operability and efficiency. The plant trials confirmed that one of the secondary ball mills could be decommissioned. Significant cost savings were achieved as a result. The success of the project demonstrates optimising grinding circuits can not only deliver the plant performance, but also a much lower unit operating cost through energy and maintenance savings.

Jan 1, 2014

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By V. I. Ryaboy, V. P. Kretov, S. E. Levkovets, I. V. Ryaboy

"Using the flotation of a gold-containing ore from a deposit in Kazakhstan as an example, we have conducted a study designing dialkyldithiophosphate collectors, in addition to xanthates, for the flotation of hard-toenrich gold-containing ores to increase gold recovery.The increased flotational ability of the dialkyldithiophosphates was determined by their surface activity at the liquid-gas interface and their hydrophobic ability, the changing of which allowed us to control the collecting power and selective ability of the dialkyldithiophosphates. The studying of the surface activity of aqueous solutions was done using the stalagmometric method and the evaluation of the hydrophobic ability was done in percentage of the relative value of the zinc ion binding in the solution in standard conditions.Studying the influence of surface activity in our designed dialkyldithiophosphate collectors, with their close hydrophobic ability, showed that even with a small increase in surface activity in their aqueous solutions, gold recovery increased by 2-3% in laboratory conditions. Using this enabled us first to apply the dialkyldithiophosphate collector BTF-161 at a plant in Kazakhstan, and then to introduce the specially designed dialkyldithiophosphate collector BTF-163, which has been in use since. Further study of dialkyldithiophosphate activity based on this concept showed us that for the range of short-chain dialkyldithiophosphate collectors with a chain length of up to ?5, the effectiveness of ore processing became lower the higher their surface activity got, with relatively small differences in their hydrophobic ability. For long-chain dialkyldithiophosphates with a chain length of over ?5, ore processing effectiveness increased with the increase of their hydrophobic ability.Based on these studies, a new effective dialkyldithiophosphate collector, BTF-1517, was designed. Using this reagent in continuous gold recovery tests allowed us to reach an 84.21% recovery with a concentrate quality of 15.66 g/t, while using the applied collector BTF-163 in similar conditions led to the recovery of 82.87% with a concentrate quality of 15.65%. As a result, the Kazakhstan processing plant decided to conduct industrial tests with the BTF-1517 collector."

Jan 1, 2018

By Johan Nell, Paul den Hoed

"Carbochlorination tests were conducted with matched particle-size fractions of rutile, ilmenite and hightitania slag in a small bubbling fluidized-bed reactor. The effects of temperature, the type and proportion of solid reductant in the charge, and the fraction of Cl2 in the fluidizing gas were investigated. Tests confirm the need for solid carbon in the bed if chlorination is to run at high rates. With solid carbon in the bed, CO supplied with the fluidizing gas does not increase significantly the degree of chlorination after 75 minutes.When large proportions (30 wt%) of carbon are added to the charge, then the reactionTiO2 + 2C + 2Cl2 = TiCl4 + 2COis favoured overTiO2 + C + 2Cl2 = TiCl4 + CO2Ilmenite is chlorinated more quickly than titania slag, which in turn is chlorinated more quickly than rutile. Rates of chlorination at 1100°C and 1000°C are much the same and significantly higher than at 900°C. Chlorination is associated with significant increases in particle porosity (even for rutile), which is brought about by the rapid initial chlorination of FeO and MnO (in ilmenite and slag) and (it is argued) by the chlorination of Ti2O3 which forms at high-energy surface sites."

Jan 1, 2003

By V. G. Prikhodko, G. I. Sukhinin, I. V. Yarygin, A. V. Fedoseev, S. A. Novopashin

"The first experiments on the vacuum drying of spherical clay sample are presented and the theoretical model of the process is considered. The model is based on the solution of the heat and the moisture transfer equations with the effective thermal conductivity and water diffusion coefficients for wet porous clay-like medium. The time and radial dependence of the temperature and the moisture were calculated for different initial conditions. The results obtained for the time dependence of the moisture content are in good agreement with the experimental results obtained in the initial period, when all the moisture in the sample did not freeze to form an ice crust. INTRODUCTION Capillary-porous materials very often occur in nature and in industry. A porous medium is a solid matrix with voids, or pores, which are continuously connected. These pores are usually filled with fluids or moisture, water vapor and air that can pass through the medium because the voids are interconnected. The void fraction in the solid matrix is referred to as the porosity. Porosity or void fraction is a measure of the void (i.e. ""empty"") spaces in a material, and is a fraction of the volume of voids over the total volume. The moisture content in porous media determines the properties of the porous body, its mechanical and thermo-physical properties, such as density, plasticity, viscoelasticity, swelling, cracking, and so on. Complex processes of heat and mass transfer occur in porous bodies when they are heated or cooled, during drying or freezing (Luikov,1966). The course of these processes depends essentially on the physical-chemical composition of the solid matrix of the porous body, on its fractal dimension, porosity and morphology. The clay and clay minerals are the most important porous materials in the history of the mankind (Mukherjee, 2013). Clay is a very fine grained, unconsolidated rock matter, which is plastic when wet, but becomes hard and stony when heated. It has its origin in natural processes, mostly complex weathering, transported and deposited by sedimentation within geological periods. Clay is composed of silica {SiO2), Alumina (Al2O3) and water (H2O) plus appreciable concentrations of oxides of iron, alkali and alkaline earth, and contains groups of crystalline substances such as quartz, feldspar, and mica. Building materials, bricks, and tiles, pottery, porcelain and faience are made from clay. Clay is used in the food and medical industry, and, not least, in the mining industry as a carrier containing aluminum, silicon and other valuable elements, as well as metals (copper, gold) as constituents, contained in the pores in the form of micro- and nano-particles or grains."

Jan 1, 2018

By L. Y. Feng

The percentage of leached zinc in massive zinc oxide ores (11.7% Zn, >2 mm) is up to 73.3 % in 120 days. Alternatively, crushed to -0.154 mm, mixed with cement 5% (wt), pelletized and solidified. The diameters of the pellets obtained are between 5 mm to 8 mm. When the pellet solidification periods are 3 days, 10 days and 45 days respectively, the alkaline leaching rates of zinc in the pellets are up to 95.8%, 89.1% and 76.4% respectively. Decreasing the solidification time can re-duce reaction time, increase dissolution of zinc in pellets and lower the effect of initial zinc concentration on leaching rate. The experiment results show that the minimum solidification time is three days, and the kinetic study indicates that alkaline leaching of the low grade zinc oxide pellets is controlled by the diffusion of the leach liquor through the gangue layer in the whole leach process, and the apparent rate constants are 3.33×10-2 day-1, 9.18×10-3 day-1, 5.82×10-3 day-1 respectively.

Jan 1, 2014

By Ana C. C. Pacheco, Maurício L. Torem

"The aim of this work was the study of the effect of the type (Fe3+, Al3+ and Fe3+ and Al3+ mixture) and of the coprecipitant concentration on As5+ removal by ACF. Removal of As5+ using sodium dodecyl sulfate (SDS) as a collector was studied by Adsorbing Colloid Flotation (ACF) at laboratory scale. The morphology of the precipitate retained in the foam was analyzed by Scanning Electron Microscopy (SEM/EDS).In order to investigate the effect of the initial concentration of Fe3+ on As removal, sets of experiments were performed with a concentration of Fe3+ in the proper range of pH (5,0 – 6,0) previously observed in the coprecipitation tests. As removal improves significantly as the concentration of the coprecipitant agent increases from 60 mg.L-1 (77,4%) to 80 mg.L-1 (99,7%). This is probably due to the higher concentration of ferric hydroxide (Fe(OH)3) which provides a larger surface area available for adsorption of As. From the initial coprecipitant concentration of 80 mg.L-1, As removal has shown to be rather high (? 99,7%), with the maximum being (99,9%) by using a Fe3+ concentration of 160 mg.L-1. Therefore, for a maximum As removal, under these test conditions, the optimum concentration of Fe3+ is 160mg.L-1.This paper also shows the effect of the initial concentration of Al3+ on As removal at a suitable range of pH (7,0 – 8,0). A very significant increase on As removal was found to occur as the initial concentration of coprecipitant was increased from 60 mg.L-1 (35,7%) to 80 mg.L-1 (97,7%) and a decrease in As floatability (43,7% - 54,5%) was found to occur from that Al3+ concentration amount. Based upon those results, the optimum Al3+ concentration so as to remove As under these test conditions is 80 mg.L-1."

Jan 1, 2003

By C. H. Veloso

"Starch is the most widely used depressant in the reverse cationic flotation of iron ores. There is however, an indication from recent studies, that other polysaccharides may successfully replace them. When starches are used in the flotation of iron ores in the presence of quartz as gangue mineral, their strong adsorption on the surface of iron oxides can be explained by the molecular conformation between the available sites on the mineral surface and two hydroxyls of starches. However, when the gangue minerals are iron-bearing silicates, the strong interaction with starch can occur on these minerals since they have the same surface behaviour as iron oxide. In this work bench scale tests were conducted in order to generate scientific knowledge about other alternatives depressants for the flotation of iron ores. A magnetic pre-concentrate from a skarn iron ore processing plant was used as feed material for flotation tests. The reverse flotation approach was used to upgrade the iron content by removing complex ironbearing silicates. The depressants used in this study were: corn starch, dextrin, carboxymethyl cellulose (CMC) and humic acid. The tests were performed under different pH conditions in order to try to relate the efficiency of depression to the pH used during flotation. The results show the important role of pH as each depressant reached its best performance at different pH values. At alkaline pH the corn starch showed best depression performance while the humic acid is more efficient at pH close to neutrality.INTRODUCTIONIron corresponds to approximately 6% of earth’s crust composition (McDonough and Sun, 1995). It is the most used metal in our lives, some of its properties as resistance and facility to be shaped makes is replacement very difficult. The primary sources of iron on our planet are minerals. The iron-bearing minerals most commonly found in nature and economically exploited are magnetite [Fe3O4], hematite [Fe2O3], goethite [FeO(OH)] and siderite [FeCO3] (L O Filippov et al., 2014). These minerals are commonly associated with other minerals (most of the time not economically exploited) forming the so-called iron ore. Iron ore is the source of primary iron for the world’s iron and steel industries."

Jan 1, 2018

By Khoi Nguyen, Keeney. Luke

An outcome of geometallurgical mapping and modeling is the generation of continuous down hole profiles of quantitative geometallurgical attributes at assay scale. These attributes vary from traditional routine data collection methods such as assays and geotechnical logging (e.g. RQD, Fracture Frequency), to new measurements including petrophysical attributes, EQUOtip hardness data and modelled estimates of metallurgical performance indices (e.g. A*b, BMWi). Highly variable continuous geometallurgical data with high spatial resolution can make it difficult to identify spatially continuous domains. An automated method based on the well known time series analysis technique of cumulative summation (CuSum) has been developed which uses statistical analysis to identify domain boundaries in down hole profiles. A bootstrap analysis automatically identifies potential domain boundary locations with associated confidence levels and a series of t-tests determine the significance of defined populations. A hierarchical clustering algorithm is applied to results to enable data sensitivity to be taken into account. The method produces statistically significant populations and is suitable for application on either single or multiple drill hole datasets. Domains defined preserve the inherent variability of the continuous down hole data and provide a method for scaling up variability data (i.e. assay interval scale) to mine scale (i.e. bench scale, block model). A major advantage of the method is its ability to provide suitable input parameters for use in spatial modeling of non-additive and non-linear geometallurgical attributes through conditional simulation techniques.

Jan 1, 2014

By G. B. Abaka-Wood

"The versatility of froth flotation has made it vital in the beneficiation of rare earth elements (REE) minerals from either high or low grade ores of complex mineralogy. There has been a significant increase in the tonnage of rich iron oxide tailings obtained from extraction of primary commodities such as copper and gold in Australia, which have been identified to have very low grade rare earth oxides (REO) (= 1%). There is a vast knowledge gap in the upgrade of REO from such tailings. The aim of this research is to investigate the feasibility of the use of fatty acids for the upgrading of REO from selected iron-oxide rich tailings. Two forms of fatty acid collectors (oleic acid and sodium oleate) were employed in this investigation. Bench scale flotation tests were carried out using a Denver D-12 cell.The effects of pulp pH, fatty acid dosage, particle size distribution (-150 +75 µm, -75 +38 µm and -38 µm) and conventional depressants (sodium silicate and starch) dosage on flotation recovery of REO were investigated. A comparison of the flotation results indicated that sodium oleate was the more efficient fatty acid for REO flotation at all the pulp pH investigated. The flotation performance is demonstrated to be particle size-dependent. The results on the effect of depressants dosage indicated that both sodium silicate and starch were unselective in reducing the recovery of hematite (Fe2O3) and quartz (SiO2) with corresponding decrease in REO recovery. Generally, Fe2O3 and SiO2 formed substantial contents of the flotation concentrates obtained, both in the absence and presence of depressants, which indicates liberation is a major challenge in achieving selective REO upgrade and recovery.The flotation tests carried out on the iron-oxide rich tailings suggest the possibility of REO upgrade using fatty acids, although particle size distribution and minerals liberation are key limiting factors in achieving selective REO upgrade and recovery."

Jan 1, 2018

By Y. S. Sun, P. Gao, Y. F. Li, J. W. Yu

"Oolitic hematite ore is one of the most refractory iron ores in the world. It is not feasible to separate iron minerals from raw ore by conventional mineral processing methods. In recent years, a new technology called coal-based reduction followed by magnetic separation has been employed to produce metallic iron powder from oolitic hematite ore effectively. In order to find the nucleation mechanism, a thermodynamic analysis of the carbothermic reduction of oolitic hematite ore was conducted by the HSC 6.0 thermochemical software. The phase transition and microstructure changes during the coal-based reduction were also investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the iron oxides in the oolitic ore were reduced to metallic iron following the route of Fe2O3–Fe3O4–FeO–Fe in reduction process. The reduction reactions preferentially occur in the high activity regions to form a higher concentration of Fe elements, and then more supersaturated Fe separated out to form new phase nuclei. Under the action of homo-aggregation and principle of minimum free energy, the iron cores continuously absorbed migratory Fe around and grew into quasi-spherical iron particles embedded in slag phase. INTRODUCTION With the rapid increase of steel industry, premium grade iron ore in China has been gradually exhausted, and its supply has become bottleneck for the development of iron and steel industry (Guo et al., 2015). Therefore, it is urgent to exploit the refractory iron ores, such as oolitic hematite ore. Oolitic hematite ore is widely distributes in France, Germany, America, Canada, Pakistan, China, and among other countries (Maynard and Van Houten, 2004; Li et al., 2011). In China, the explored reserve of oolitic hematite ore is 3.72 billion tons, which accounts for approximately 1/9 of total iron ore resources of China (Gao et al, 2016). Oolitic hematite ore possesses complex composition,"

Jan 1, 2018

By Y. Rama Murthy

Around 90% of the chromite resources of India are concentrated in the Boula-Nuasahi Sukinda belt of Orissa state. In order to conserve these valuable ore resources strategically, several companies established chrome ore beneficiation plants in this region. The general beneficiation process in these plants consists of gravity unit operations such as Floatex density separator, spiral, wet shaking table etc. Most of these gravity circuits suffer huge losses of valuable minerals in the tailing. Any attempt towards decreasing these losses would not only increase the limited reserves in India but also make the economics of the operations more attractive. Apart from the liberation phenomena, in many of the operating plants considerable quantity of values are lost in the tailings, due to inconsistent feed quality, inappropriate selection of operating and design parameters. Mineral engineers in this regard have to play a proactive and continuous role to improve the performance of all separating units by modifying even small changes based on tests conducted in laboratory under controlled conditions followed by attempts to make necessary changes in the plant. For such improvements, accurate data collection and proper data interpretation followed by making necessary change which is implementable in an operating plant play a very critical role in performance of the circuit. Databank collected over a period of time under various conditions would also help in overcoming the future problems related to either variation in the feed characteristics or specific demand by metallurgical industries. The above concept was adopted in one of the operating chromite beneficiation plant at Sukinda. The approach adopted and practical problems encountered during the study were reported in this paper. The result of trial campaign has shown that, an overall product assaying 30.2% Cr2O3 from the feed (18% Cr2O3 ) can be produced to in single stage. The final discards of the process contain 12% Cr2O3. Keywords: chromite, chromite beneficiation, chromite losses, gravity concentration techniques, plant operating data bank

Sep 1, 2012

By Jing Zhou

2-hydroxy-3-naphthoy hydroxamic acid code name F203 is a good collector of cassiterite, 1-hydroxy-2-naphthoy hydroxamic acid code name ZJ-3. F203 and ZJ-3 are similar series of isomers. They have similar naphthye, and similar series of functional OH and ?CONHOH, but the seat of OH and ?CONHOH group are different, on the F203 is 2.3; on the ZJ-3 is 1.2, ortho position too. According to Isomeric principle ZJ-3 is a good collector of cassiterite slime too. Using ZJ-3 as collector flotation -10µm occupies 90%, grade 1.16% Sn cassiterite slime of Da Chang Chehe concentration plant, pass one coursing flotation, two cleaning and one scarenging flotation, and obtains grand 18.26% Sn, recovery 92.68% cassiterite concentrate. The result proves the Isomeric principle of flotation reagents is correct again. This principle may supply to synthetize new flotation reagents reference. Keywords: F2O3, ZJ-3, cassiterite flotation, Isomeric principle, Isomeric principle of flotation reagents

Sep 1, 2012

By A. Erdem

In this study, approximately 3 tons of coal sample taken from thickener entrance was prepared by mineral processing techniques and cleaned by gravity methods. The samples were classified to 5 size fractions by wet screening. The size fractions of +1mm and -1 +0.500 mm were chosen for direct consumption or cleaning by spirals. The studies by Multi Gravity Separator (MGS) were carried out with the -0.500 +0.280 mm and -0.280 +0.020 mm size fractions where the -0.020 mm fraction does not used in the experiments. The clean coal fractions of +1 mm and -1 +0.500 mm obtained by classification were subjected to lower calorific value (LCV), ash and total sulphur analyses. The results were 4168-4946 kcal/kg (on dry basis), 31.01-38.54 % ash and 4-4.27 % total sulphur content respectively. The results of the clean coal concentrated by MGS experiments in -0.500 +0.280 mm fraction was found 5918 kcal/kg LCV, 19.82 % ash content and 80.47 % combustible recovery. The results for the -0.280 +0.020mm fraction were 6004 kcal/kg LCV, 19.19 % ash content, 80.47 % combustible recovery respectively. With reference to the above experimental results, pre-economic evaluation studies were completed and decided to construct an additional unit to the plant. Capacity of the constructed unit is 75.000 t/y which corresponds $ 2.600.000 income in a year. General Directorate of Turkish Coal Enterprises concluded to apply this project to the other coal washing plants in the country due to the successful results of this study and laboratory studies has been going on by MTA currently. Keywords: coal tailings, mgs, recovery, washery, pre-economic evaluation

Sep 1, 2012

By P. Prakash

A dual-drive planetary mill, which has a rotating shaft that sweeps a circle of diameter 750 mm, has been designed. The planetary mill is powered by a 5 hp motor to rotate the main shaft and a 3 hp motor to rotate the jars. The charge dynamics inside the horizontal-axis planetary ball mill was established using three-dimensional DEM simulations. The simulation results provided data to determine the impact energy distribution and the effect of process parameters such as mill speed and filling. It has been observed that the mean impact energy per unit time increases with rotation-to-revolution ratio, whereas the average number of inter-particle impacts per unit time decreases. The mill was also used to synthesize a variety of powders. Here three case studies of reaction milling are briefly presented: (i) cementite and silicon carbide, (ii) oxide dispersed strengthened (ODS) steel, and (iii) magnetite from blue dust. In each case, the powder was produced by mixing and then milling the corresponding pure components. The phase evolution, particle size distribution, and morphology of particles during milling were studied for various samples collected at different milling times using laser size analyzer, SEM, TEM, and Mössbauerspectroscopy. The results established a convenient way to produce powders of high technological and commercial value.

Sep 1, 2012

The objective of the paper is to develop a material balance calculation procedure for a production unit involving two plants separated by a pipeline. The case study is taken from the oil sands industry. The raw sands are first mixed with water in a conditioning plant, then transported through a pipeline to an oil extraction plant. The combination of pipeline dimensions and nominal throughput creates a significant variable time lag between the two plants. As usual, mass balance calculations required for the evaluation of plant performance indicators, such as bitumen recovery, are inaccurate due to measurement errors. In addition, in the present case study, the time lag of the pipe creates an additional source of uncertainty, which may lead to misinterpretations and wrong decisions. Raw data are usually reconciled through steady-state mass balancing, to correct for measurement errors. However, because of the significant pipeline dynamic lag, standard steady-state daily mass balance may fail at giving an appropriate picture of the operations. The proposed solution to the data reconciliation problem includes the use of a pipeline plug-flow model in the mass balance calculation. To fulfil the industrial constraint that current data reconciliation must not modify past reconciled values, while still satisfying dynamic constraints, a daily one-step method, i.e. a unitary filter-ing horizon, is recommended. The method is illustrated with simulation data, and the results com-pared to those of standard data reconciliation methods.

Jan 1, 2014