Search Documents

By Reza M. Rahman

The froth phase plays an important role in the flotation and upgrading of the final concentrate. At present, the techniques that have been used in the mineral industry to measure the froth recovery have limitations. The aim of this paper is to investigate the performance of the froth in an industrial flotation cell. A unique device has been developed which is capable of decoupling the froth zone from the pulp zone. It consists of two concentric tubes. The inner tube acts as a dropback collection chamber or catcher. The particles that detach from the froth phase fall directly into the catcher and are collected as froth dropback. The froth recovery measurements were carried out in a rougher bank of a copper concentrator treating sulphide minerals. The dropback device is designed so that it can be immersed into a plant size flotation cell and plant froth recovery measurements can be taken at any given time. During the experiments, the bubbles laden with valuable mineral particles entered the device from the plant flotation cell, subsequently rising to form a froth layer at the top of the device. The particles that detached from the froth zone were collected in the dropback collection chamber whereas the concentrate sample was collected by a launder. By drying, sizing and chemical analysis of the concentrate and dropback samples, the froth recovery, was estimated on the basis of the valuable component. The effect of air rate on froth recovery was also investigated. Keywords: flotation, froth, dropback, froth recovery

Sep 1, 2012

By Saveliy F. Kaplan, Valeriy N. Tsyplakov, Vasily N. Kovalev, Igor A. Agapov, Nikolai V. Vorob’ev-Desyatovskii

"Based on the experiments, a possibility of successful processing of double-refractory gold sulphide concentrates with a high content of natural organic carbon, which has a high sorption capacity toward gold chloride complexes, has been demonstrated. The proposed approach involves deep burnout of sorption-active organic carbon in an autoclave at a higher temperature and a longer retention time. INTRODUCTION It is known that one of the reasons why gold-bearing ores and concentrates are refractory is the occurrence of fine gold in sulphides (usually in pyrite and arsenopyrite) in ores and concentrates. In addition, refractory gold-bearing ores and concentrates also contain an organic carbonaceous material, which has a sorption capacity towards gold chloride complex, making the ore or concentrate even more refractory. In pressure oxidation, metallic gold is oxidized by Fe (III) aqua-ions and complex Au(Cl)4- ions are formed at temperatures over 180°C, in the presence of chlorides contained in ores. Complex gold anion is adsorbed on the organic carbon surface and then reduced to Au0; the chloride ion is regenerated and gold, adsorbed on organic carbon microparticles, is ultimately transferred to tailings (preg-robbing). Currently, there are several suggestions how to suppress preg-robbing (Simmons, 1998, Pyke, 1999, Rees, van Deventer, 2000, Zhao Jun-wei, 2008). It can be done by reducing the organic carbon content by processing (flotation, etc.),reducing chloride ion concentration by preliminary washing of concentrates in thickeners, reducing the adsorption capacity of organic carbonaceous material by introducing some organic substances that are strongly adsorbed on its surface (blanking agents), and reducing the redox potential of the slurry liquids by introducing neutralizing agents (limestone)."

Jan 1, 2018

By Fernando Concha

"Thickening development and innovation in the 20th Century occurred in two decades periods. From 1900 to 1920, Dorr invented the continuous thickener and the first method of thickener design was proposed by Coe & Clevenger. From 1920 to 1940, the operating variables of continuous thickening were discovered by Comings at the University of Illinois. From 1940 to 1960, the first theory of sedimentation was proposed by Kynch and several authors, Talmage and Fitch, Ysioka and Hasset used this theory to develop new thickener design methods. From 1960 to 1980 Shannon and Tory demonstrated that this theory applied exactly for the sedimentation for small rigid spheres in water and Scott showed that it is not valid for flocculated suspensions. From 1970 to 1990 the phenomenological theory of thickening was developed based on the theory of mixtures. Papers by Kos, Bascur, Thacker and Lavelle, Concha and Bascur, Concha and Barrientos, Auzeris, Buscal and White, Landman, White and Buscal show the application of this theory to thickening and Adorjan presented the first thickener design method based on this theory. In 1980s the mathematical analysis and solutions of Kynch’s model for batch and continuous thickeners was obtained by Bustos. The new Century brought solution to the phenomenological thickening model which was applied to thickener design, simulation and control. The method of thickener parameter determination was improved by designing new laboratory and on-line instruments and advanced control strategies was designed and validated in plants. Structural thickener design produced improved feedwells and feed dilution mechanism, stronger raking mechanism and different thickener shapes according to new ambient requirements, such as high rate thickener and paste thickeners that increase the water recovery. New challenges include better flocculation and advanced control strategies."

Jan 1, 2014

By Markus A. Reuter, Jacques J. Eksteen

The modelling of bath type furnaces tends to be either fundamental in nature or total empirical "black box models". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Therefore, this paper argues that to understand complex metallurgical furnaces a hybrid approach is the only method to fully grasp the intricacies of metallurgy, to improve operations, economics as well as environmental performance.

Jan 1, 2003

By P. Gao, J. W. Yu

"Magnetizing roasting-magnetic separation is an important route for the beneficiation of refractory iron ores. In this investigation, a pilot-scale fluidized magnetizing roasting reactor was introduced and used to study the effects of roasting temperature and the flow rates of reducing gas CO and fluidizing gas N2, on the magnetizing roasting performance of an Anshan-type carbonate-bearing fine iron ore. The results showed that the hematite was almost reduced to magnetite by a gas mixture of 4 m3/h CO and 1 m3/h N2 at a roasting temperature of 540 °C. Under the optimized conditions, a high-grade magnetic concentrate assaying 66.1 wt.% Fe with a recovery rate of 91.2% was achieved from an Anshan-type carbonate-bearing fine iron ore assaying 42.0 wt.% Fe. The XRD, VSM, and optical microscopy analyses revealed that the siderite was successfully converted to magnetite by roasting. Some coarse hematite particles were difficult to reduce to magnetite completely; however, these generated magnetite particles with a fine hematite core could also be effectively recovered by magnetic separation after liberation from gangue minerals due to their strong magnetism. INTRODUCTION Magnetizing roasting followed by low-intensity magnetic separation has been considered as an effective solution, both technologically and economically, when upgrading refractory iron ores (Zhang et al., 2012; Peng et al., 2012; Li and Zhu, 2012). According to the type of roasting reactor, the magnetization roasting can be divided into shaft furnace roasting, rotary kiln roasting, and fluidized bed roasting (Zhu and Li, 2014).Shaft furnace magnetization roasting system is mainly composed of heating and reduction processes. The hematite ore is first heated to 700~800 °C in the heating zone, then falls into reduction zone where the weakly magnetic hematite is reduced to magnetite by coke oven gas at 550~600 °C (Yan et al., 2012). However, several years of engineering practices indicate that the shaft furnace can only process the hematite ores with a granularity of 15 ~75 mm, and the shaft furnace roasting is also characterized by heterogeneity of roasted product. Hence, the shaft furnace magnetization roasting technology is gradually replaced by high-gradient magnetic separation with the development of high-gradient magnetic separator. The rotary kiln generally handles the hematite ores with a grain size of less than 30 mm (Zhu and Li, 2014), however the formation of clinker ring in the rotary kiln will affect the yield of iron resource. In the fluidized bed furnace, the hematite ore is shaken up by an upward current of gas which maintains the individual particles in suspension (Yu et al., 2018). The precise adjustment of the gas velocity to the particle size and the specific weight of the hematite ore, make it possible to generate a floating mixture of gas and solids which behaves almost like a liquid (Yu et al., 2017a). The process is reported to have the following advantages over the other roasting techniques: ease of control due to absence of moving parts within the reactor, homogeneity of roasted products, ability to handle fine particles, and high efficiency of heat transfer and mass transfer (Li et al., 2015; Yu et al., 2017b). However, the simultaneous heating and reductive magnetization of hematite ore occur at the same place in the conventional fluidized bed reactor. Therefore, the reductive atmosphere, as well as the safety and stability of anti-explosion are hard to be controlled. Besides, the roasting temperature for conventional fluidized bed furnace is usually up to 950~1150 °C (Liu et al., 2017). Thus, the formation of clinker ring caused by high temperature will affect the operating efficiency."

Jan 1, 2018

By V. M. Bystritsky, M. G. Sapozhnikov, G. M. Nikitin, A. B. Sadovsky, Yu. N. Rogov

"At present kimberlite ore is processed in crushers or grinding rolls with subsequent grinding in wet mills down to a size of 0.2 mm. The basic disadvantage of the standard diamond processing technology is that crushing kimberlite ore can damage the most valuable large diamonds of few carats. Tagged neutron method offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The results of the tests of the neutron separator prototype carried out at the Lomonosov processing factory of PJSC Severalmaz are discussed. The possibility to detect the diamond in the rock whose size is 10 times larger than the size of the diamond is demonstrated.INTRODUCTION At present standard diamond processing technology implies disintegration of kimberlite ore in crushers or grinding rolls down to a size of 0.2 mm. It inevitably leads to high probability that large and most valuable diamonds could be damaged. The fraction of diamonds which lost integrity in the process of ore enrichment could be as large as 35-65% [1]. Tagged neutron method (TNM) [2] offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The main idea of the TNM is irradiation of an object by fast 14.1 MeV neutrons from binary nuclear reaction d + 3H ?4He + n (1) and detecting (tagging) the 4He (a-particle) that accompanies neutron. That gives possibility to determine direction of the neutron momentum. Those tagged neutrons irradiate kimberlite ore under investigation and produce gamma rays via inelastic scattering reactions with nuclei"

Jan 1, 2018

By Gauti Asbjörnsson

Material handling is an essential part of the aggregate and mining industries. Mixing and blending of granular material can affect the grading and particle size distribution of the material leaving the system. Segregation and variability can cause problems in the downstream process while insufficient capacity will disturb upstream processes. Process plants utilize surge bins for handling recycle streams of material and act as a buffer for the process. The flow through the surge bin is usually controlled by a simple PID controller or PID controller in combinations with a plant-wide controller. Even though the surge bins play an important role of smoothening out the plant and creating a steady operating condition they are seldom included in plant simulations. This can lead to a number of problems in the form of decreased plant capacity, plant lockdown, and even operation units malfunctioning. The main objective of this study is to investigate the dynamic behavior in surge bins and develop a model more suitable for representing this behavior, which can occur during operation, for dynamic simulations. The proposed model adopts vertical layers which allow for flows between segments depending on the level of neighboring segments. This enables both the representing of segregation within the system and gives an indication on the effects from different inlet- and outlet placements. The proposed model was developed in MATLAB/Simulink and validated against an actual bin with the total capacity of 660 m3 in platinum ore application. With the new bin model significantly higher fidelity and more accurate dynamic, simulation results were achieved. Keywords: dynamic simulation, modeling, segregation, material handling, MATLAB/Simulink

Sep 1, 2012

By B. Csoke

To improve the efficiency of the crushing/screening plant of Bazalt-Középko Kobányák Ltd. (Hungary), the implementation of computer aided quality control is planned. In the current phase, the R & D work aims at the solution of high-priority tasks: 1) Developing the process models, validation of the models by means of industrial measurements. 2) Developing the algorithm for the process control of the crushing/sizing plant. 3) Developing the suitable computer program. To develop the mathematical models of crushing (breakage and probability functions) and to determine the model parameters, the experimental industrial trials were carried out on hydrocone crushers of types Svedala H 4800 EF and H 4800 F, changing the gap size and crushing relatively narrow grain size fractions. Additionally, the parameters of the separation function for the screens operating in the system were determined. It was established that the crushing probability depends on the grain size of the feed (Y) and the gap size (s), so the breakage probability S, for each cone crusher, can be well characterised by the function formed using the ratio of these two parameters: SfYsf==. The distribution of the broken grains can be described reliably using the relative grain size distribution function B(? = x/Y) (usually Schuhmann-Gaudin- or Rosin-Rammler-shaped function). For the screens, the probability function ()2()111/NTx = xd ???---???? is suitable for cha-racterising the separation (where x? grain size, ?-open-area ratio, d ? rectangular screen aperture size, N ? number of appearance of the particle on a screen surface). Using these functions, the comminution circuits were described by means of vector/matrix equations. The calculations and measurements verified the reliability of the developed models and algorithms.

Jan 1, 2014

By Alejandro Rubio-Lopetegui, Gonzalo Montes-Atenas

The occurrence of Enargite (Cu3AsS4) in hydrometallurgical plants bears a number of challenges. One question lies on how Copper and Arsenic can be selectively extracted from the solid surface structure when immersed in aqueous solution. The leaching of Enargite in ambient conditions has been extensively studied; nevertheless, challenges regarding the process kinetics and surface structures enabling the extraction process remain ill-understood. Prior knowledge indicates that different conditions of pH, Eh, temperature, speciation of the aqueous phase or variations of these parameters defines the overall rate at which metals and other elements will be transferred to the solution. One aspect that the research studies have seldom addressed involves studying the main features of the surface structures formed during the leaching process at the outmost surface atomic layer. Such structures will mediate between the solid bulk and the solution to undertake subsequent stages of leaching process. The aim of this research work is to critically analyze the state of the art of Enargite electrochemistry from the mediator formation-dissolution mechanisms standpoint occurring at the mineral-solution interface. The most probable mediator species reported in the literature were found to be: Arsenolite and Sulfur (acidic media), Covellite (acidic and alkaline media) and Tenorite (alkaline media). As a result of this analysis, it was observed that the surface speciation was not in full agreement with the previous knowledge suggested to explain Enargite leaching reactions and, therefore, modified Eh-pH diagrams are presented. The acquired insights on the surface structures rising from the Enargite-aqueous solution interactions is further revised to provide new experimental protocols towards selectively separating Copper and Arsenic through hydrometallurgical paths.

Jan 1, 2014

By R. Imhof, S. E. Sánchez-Pino, H. Sprenger, S. A. Sánchez-Baquedano

"In 1992, Ingeniería de Minerales started with the introduction of pneumatic flotation technology in Chile and South America. This technology consists of vertical cells and gyratory cells, used mainly under actual operational conditions, with pilot units directly installed in the concentrator circuits of the industrial process. Successful industrial applications have been observed at Los Pelambres, in the molybdenum plant; at Codelco Andina in the molybdenum plant as pre-rougher to produce directly a final concentrate; in the copper circuit at Las Luces as pre-rougher producing final concentrate using sea water; at Minera Valle Aconcagua where a full automatic plant produces pre-concentrate from fresh tailings as feed; at the silica and silicate reverse flotation circuit of Compañía Minera del Pacífico; in cleaning the final concentrate of Zn by reverse flotation removing ultrafine carbonate; and in a plant that reprocesses fresh tailings from a copper slag flotation process. Positive operational changes in the design of the flotation circuit have been seen in plants using G-cells and V-cells, improving the performance of flotation circuits and the quality of final products. The high concentration of bubbles and micro turbulence produced by the pneumatic aeration units provide a high probability of collision and attachment, reducing dramatically the residence time. Though it is a pneumatic flotation, no compressed air is needed, and the equipment is characterized by low maintenance costs, full automation, savings in investment and energy."

Jan 1, 2014

By D. Pienaar, B. McFadzean, T. Jordaan

"Dithiophosphate (DTP) collectors have the lowest affinity for sulfide mineral surfaces compared to other common sulfide mineral collectors, such as xanthates and dithiocarbamates. In some cases it has been found that DTP does not adsorb onto the mineral surface at all and yet increases in recoveries and grades are noticed with the addition of DTP. Many studies have investigated the interactive effects of collector mixtures. However, there have been relatively few studies on the interactive effects between frother molecules and collectors. This study investigates the interactions between different types of frothers and sodium diethyl dithiophosphate.The study found that there were large increases in pyrite and galena microflotation recoveries at both pH4 and pH9 when DTP was mixed with small amounts of frother at a constant bubble size, showing that these increases were neither mineral-specific nor pH-specific. The same effect was not present when xanthate was used as a collector. The increases in recovery when using the DTP-frother mixture were similar irrespective of the type of alcohol or polypropylene glycol frother that was used. In an attempt to distinguish the mechanism of enhanced flotation recovery, various supplementary experiments were performed. It was found through adsorption experiments that no DTP was adsorbing on to the mineral surface. Therefore, interactions at the air-water interface were performed. Surface tension and critical coalescence concentration tests showed that, while DTP is a weak surfactant at the air-water interface, it does not have a synergistic effect in the presence of frother. DTP-frother mixtures do, however, show interactions in the froth phase, indicating an interaction in the thin films. It is proposed that there is a DTP-frother interaction on the bubble surface that enhances the rate of film thinning at the 3-phase bubble-particle contact."

Jan 1, 2018

By L. Gutierrez, R. Yepsen, F. Alarcón

Chile is the world's largest copper producer which is mostly in the form of sulfides for which froth flotation is the most efficient concentration process. As a result a concentrate that contains high concentrations of copper sulfides such as chalcopyrite, chalcocite and enargite is obtained. In the last decades processing of ores containing high concentrations of enargite (Cu3AsS4) has continuously increased in Chile, which is related to the fact that ore deposits nawadays are more heterogeneous and complex. Enargite is a mineral that contains arsenic and its presence in the copper concentrates implies severe penalties. In addition, the shortage of fresh water has driven the search for new alternative sources of water, among which seawater has proved to be one of the most attractive. The objective of this research is to study the behavior of the enargite in the process of flotation using seawater, and at the same time to compare its behavior with the results obtained using conventional water. The study was carried thorugh micro-flotation tests using pure samples of enargite, at pH values ranging from 4 to 11, both in fresh and seawater. PAX and MIBC were used as collector and frother respectively. Micro-flotation tests were also done at different redox potential conditions so that the effect of the surface oxidation of enargite was evaluated in seawater. The results indicate that the recovery of copper from enargite is reduced in seawater compared to fresh water, in particular at the pH values close to those of the formation of the first hydroxy complexes of Mg and Ca. In general, the experimental data indicate that the floatability of enargite is strongly affected when seawater is used, in particular at oxidizing conditions. These results suggest that Mg2+ and Ca2+ ions contained in seawater interact with the surface of enargite forming hydrophilic species.

Jan 1, 2018

By Vitaly Kretov, Valery Golikov, Vladimir Ryaboy, Elena Shepeta

"The aim of the study was to develop and implement more efficient dialkyldithiophosphate collectors. A hypothesis has been formulated on the action of dialkyldithiophosphates in the flotation of sulphide ores based on the assessment of their complexing properties and surface activity at the liquid-gas border. Dialkyldithiophosphates form weaker complexes with cations of heavy metals compared to xanthates, and are characterized by a large difference in the strength of their complexes with heavy metal cations. It provides higher selectivity of dialkyldithiophosphates in the separation of non-ferrous metal sulphides and iron sulphides from them. To make a quality assessment of the impact of surface activity of the synthesized collectors on their selectivity of action and collecting power, an assessment of the surface tension of their aqueous solutions has been performed using the stalagmometer method. It is well known that a stronger collector is characterized by a greater surface activity, in contrast to a more selective collector which is characterized by a lower surface activity. Based on studies, new dialkyldithiophosphate collectors BTF 163 and BTF 1552 are suggested for use in the flotation of sulphides to increase the recovery of copper, gold and silver. The collector BTF 163 was introduced at a gold processing plant in Kazakhstan and has been undergoing industrial testing in the sulphide cycle of scheelite-skarn-sulphide ores in a factory in the far east of Russia. The collector BTF 1552, which increases the recovery of silver and gold by 3%, was approved for industrial testing in another far-eastern factory. A modification of the reagent BTF 1552, the new reagent BTF 1522, was introduced in the flotation of copper-zinc ore at a factory in Kazakhstan."

Jan 1, 2014

By Reinol Compañero, Ivy Gonzales, Herman Mendoza, Brian Buenaventura

"The extraction of gold in the Philippines has been a significant challenge for the past decades. Around 70-75% of gold mined in the country can be accounted from the small-scale mining industry which primarily use the traditional cyanidation and amalgamation; processes which have been advocated due to its adverse affects to health and environment. To address this challenge, an alternative clean and sustainable technology was developed for the small-scale miners to recover gold and other metal/mineral values efficiently from Philippine ores. An initial survey was conducted and followed through with extensive mineralogical investigations ascertain the best method applicable. It was determined that Philippine gold occur in ore as (1) very fine particles in the microns range, (2) free-milling, which is in abundance, and (3) locked particles with sulfides --- it was concluded that enhanced gravity concentration and flotation are viable alternatives. A comprehensive test regime was followed to check the response of the ores obtained from different small-scale mining districts across the country. It was shown conclusively that the gold ores respond positively, with recoveries using gravity concentration and flotation of at least 95% and 88%, respectively; exceeding the nominal recoveries using cyanidation or amalgamation. A specific process flow was designed for each type of ore with customized parameters. It was determined that while capital expenditure of implementing these alternative processes is higher than what is currently being used, the operational aspects show that it is much more economical to apply enhanced gravity and flotation. It should be noted that the process developed addresses the critical issue of environmental costs which should be more than enough to justify the shift from the current to the novel and sustainable technologies."

Jan 1, 2014

By H. Wotruba, L. Gronen, A. Hellmann, S. Sindern, J. Katzmarzyk

"This paper focuses on the beneficiation of the REE-Y-Nb-Zr complex ore from the ‘Khalzan Buregtei’ deposit, Mongolia. Pre-concentration based on mineralogical studies was investigated at the Unit of Mineral Processing (AMR) and the Institute of Applied Mineralogy and Economic Geology of RWTH Aachen University. In order to minimize the energy consumption in the most energy intensive grinding process a pre-concentration process using dry magnetic separation of particle sizes coarser than required for the liberation of the valuable ore minerals was designed. Dry magnetic separation in the particle size range of 63-250 µm is suitable as the pre-concentration method, due to the intergrowth of REE-Y-Nb-Zr bearing minerals with magnetic minerals determined by QEMSCAN© analysis. The results showed that a mass reduction of 45.3 wt.-% at high recoveries of REE, Y, Nb and Zr (90 wt.-% and higher) in the pre-concentration product was achieved at the beginning of the process chain. The improvement of process efficiency as shown in this study depends on the abundance and association of minerals affecting the magnetic properties (e.g. hematite) of the ores. Therefore, these mineralogical parameters are as important as grain size and ore grade for the geometallurgical evaluation of potential mining operations at ‘Khalzan Buregtei’.INTRODUCTION Polymetallic deposits containing other critical elements besides REE have the advantage of being robust to economic development and fluctuations of individual metal prices. (Gronen et al., 2016). These deposits can host economic grades of heavy and light REE, Y, Nb, Ta, Zr in complex mineralogical compositions. About 120 deposits of this type are known worldwide, including ‘Norra Kärr’ in Sweden, ‘Strange Lake’ in Canada and ‘Khalzan Buregtei’ in Mongolia which are not valued economically yet. (Salvi. & Williams-Jones, 2004.)"

Jan 1, 2018

By V. P. Yakushkin, B. S. Ksenofontov

"Multistage model designed and used for more detailed description of floatation process. The study develops a new model of flotation kinetics description. It defines flotation as process that consists of several stages: air bubbles and particles are separate, air bubbles and particles form a raising aggregate, aggregate raises to froth layer. This description significantly differs from commonly used model, which is much simplified. The multistage model gives an in-depth description and considers different aspects of flotation. Experimental approval of the new model resulted in its accuracy.The model is to be used for description of all flotation processes’ kinetics of wastewater treatment. It helps in accurate designing of flotation treatment plants and may be used for further research of flotation process. Columnar flotation installation was designed by using multistage model. This installation consists of new tubular aerators with special ejectors, froth pressing system as well as unit of thin-layering lighting to catch microflotocomplex “particle – bubble”. Usage of tubular aerators allowed to aerate the overall volume of pulp. Due to use of special ejectors with longer mixing camera we state higher volume of small-sized floto-active bubbles. Use of multistage model allowed to optimize and get higher technological results of potash salts enrichment. Tests were conducted on centrifuges-floatation installation system. Meanwhile, froth concentrate contained mainly thin hydrophobic particles sized circa 0,1 mm. As a result we set that during floatation cleaning process of froth concentrate 95-98% of chloride potassium (KCI) is derived from foam.The final product satisfies production quality. Columnar floatation installation productivity was 17 – 21 m3/m2h, which is a high technological result. Columnar floatation installation is one of the best examples of concentrating equipment using nearly all technological indices."

Jan 1, 2018

By Christopher Robben, Alexander Mosser

"X-ray transmission (XRT) sorting has been introduced into the minerals industry in 2006 and has found various applications in diamonds, industrial minerals and metal ore processing since. The technology offers planar projections of the atomic density of single particles similar to the principle known from airport scanners, but being capable of treating up to 150tph per metre working width. In 2010, a pilot operation using a belt-type sensor-based sorter went into production at the Mittersill mine to treat the fraction 16-28mm. After an optimisation phase, the results were superseding expectations and therefore in 2012 a bigger production plant was set up. Two XRT-based sorters are parallel in operation since. One is treating the fine fraction 16-30mm while the other one is treating the coarser fraction 30-60mm after the secondary crushing stage. The XRT sorters are operated with the objective to reject barren waste before it enters the mill and flotation plant. 105,000tpa of waste material are rejected per year and can be sold as aggregate for road construction. This means that about 22% of the run-of-mine ore are rejected at an early stage with a waste reject grade lower than 0.03wt%WO3. The installation has not only led to lower specific operating costs but also led to reduced tailings disposal in an environmentally sensitive area. This allows the mine to reduce its headgrade which allows for a longer mine life. Alternatively it is possible to produce more tungsten concentrate, which is delivered to the smelter. This article will introduce the technological principle of XRT-based sorting and will discuss the flow-sheet of the Mittersill mine. Experiences that have led to the current plant design are described as well as the impact it has on the operation."

Jan 1, 2014

By Yu. Gurevich, M. Teremova, I. Prokopev, A. Razvjaznaya, N. Algebraistova

"The objective of this work is the scientific justification and development of efficient and environmentally-friendly method of bulk concentrate preparation for selection with application of microbiological practices. This research suggests to apply Pseudomonas Japonica bacterial culture to the bulk concentrate before the selection circuit in order to clear the surface of sulphides from the xanthate skin. It is also suggested to apply bacterial consortium Ochrobactrum ?nthropi and Pseudomonas aeruginosa JCM 5962 for desorption of diesel residual concentrations. High-efficient and environmentally friendly method of copper-molybdene and lead-zinc bulk concentrate selection was developed based on theoretical and experimental research work with application of microbiological practices. In comparison with conventional methods (steaming, sodium sulphide washing) the above suggested bio-technological method of bulk concentrate preparation before selection cycle will allow to reduce material and power expenditures, and it is also environmentally friendly. INTRODUCTION High-efficient selection of sulphide bulk concentrate is gained exclusively after collecting agent is removed from mineral surface. Therefore, the problem of bulk concentrate preparing before the selection cycle is acute, since the further technological parameters of the subsequent separation depends on the effectiveness of pulp preparation. Existing traditional ways of bulk concentrate preparation. such as washing or steaming, are characterized by high energy and material costs in industrial conditions [1,2]. The microbiological treatment before separation of the bulk concentrate into different kind of concentrates appear one of perspective processes for treatment of bulk concentrates [3,4]. At the present time, the world practice of processing mineral raw materials demonstrates the wide application of technologies using microorganisms: bacterial leaching and oxidation, purification of industrial wastewater. This is due to the fact that biotechnological methods are environmentally safe, low-cost, and suitable for refining complex ores and raw materials of industrial origin."

Jan 1, 2018

By X. F. Cao

There was a large reserve of bauxite resources in China. And these resources were mainly the dias-pore-bauxite and contained plenty of aluminosilicate including kaolinite, illite and pyrophyllite. Reducing the contents of aluminosilicate would be significant to the using of Chinese bauxite resources. In this paper, from the single mineral flotation experiments, the surface properties and flotation beha-viours of aluminosilicate including kaolinite, illite and pyrophyllite, using dodecyl amine (DDA), N, N-dimethyl-dodecyl amine (DRN12) and N-dodecyl-1, 3-propane diamine (DN12) as collectors, had been investigated. The flotation results shown that the flotation behaviours of aluminosilicate had been influenced greatly by three amine collectors; and the effect was in the order of DN12>DRN12 >DDA. On the basis of FT-IR spectra and zeta potential measurements, the ionization of surface hydroxyl, as well as isomorphic exchange of surface ions, accounted for the mineral surface charges. And the mechanisms of interactions between the mineral surface and collectors mainly included two modes: electrostatic adsorption and hydrogen bonding; for the DDA and DRN>DDA. 12, the mechanism was mainly electrostatic adsorption; and for the DN12, the mechanisms of electrostatic adsorption and hydrogen bonding both existed. Results of quantum chemistry research shown that the collecting ability of amine collectors was greatly influenced by the electro-negativity of N in the amine molecules; and The |E(EHOMO| and ?E (HOMO-ELUMO) of N atom in DRN12 and DN12 were lower than that of DDA, and the positive charge of ?N group in DRN12 and DA12 were higher than that of DDA. All these calculation results could explain the collecting power of DN12>DRN12>DDA.

Jan 1, 2014

By Verónica Fernández, Jaime Solari

"The Chilean Environmental Impact Assessment System (EIAS) of investment projects was created in 1994, date in which the General Environmental Law was enacted. The compulsory environmental approval of projects began in 1997 when the Regulation (S.D. 30/97) was officially issued. By beginning late to regulate the environmental effect of investment projects, Chile could take advantage of the international experience in the matter and therefore, the EIAS has many of the attributes of successful environmental assessment systems elsewhere. Thus, the main characteristics of the Chilean EIAS are: preventive, single-window, specific to certain projects, multi-agency assessment at the regional scale, 3 kind of applications, deadlines, citizen and native communities participation, link to relevant permits, definite conditions of approval/rejection, review of applications by an ad hoc institution. The Chilean EIAS has allowed during the period 1997-2013, the review of 21,110 projects for a total investment value of US$ 408 billion, of which a 76% have been approved. In the case of the mining projects, the corresponding figures for the similar period are 1,257 projects for a total investment value of US$ 119 billion, of which 78% projects were approved. The experience derived from the environmental impact assessment of mining projects indicates that Chile has been successful in linking together mining development with environmental protection. There is still little prejudice against mining and this is a still a largely welcome economic activity at all levels in the relevant regions of the country. The challenge that mining companies face today in Chile is to improve the sustainability of projects and operations, by learning to share scarce and valuable resources (water, glaciers, renewable energy) with the local and native communities, through a process of dialogue whereby mining development also generates benefits for these communities."

Jan 1, 2014