Search Documents

By Shinichi Takagawa

The deep sea hydrothermal deposits are one of the most prospecting resources, and various works to develop these mines are now underway. There are also various methods for the pre-site survey of the mines: acoustic survey, electro-magnetic survey, and others. However, as a precise method at the final survey, drilling/coring is indispensable to confirm the three-dimensional distribution and to grasp the dignity of the ores for the final decision of industrialization. This drilling/coring at the final survey is done at many points with distance of 15~25m between each point for on-land deposits. This means that 1km by 1km square area requires (1,000m/25m)2 ~ (1,000m/15m)2 = 1,600 ~ 4,500 holes. The drilling/coring depths will be around 30m or more for the hydrothermal deposits. This depth seems very shallow, but because the stratum is very brittle and is very difficult to core, the average core recovery ratio is around 50%, and 0% core recovery happens very often. Thus, the indispensable work of coring for grasping the dignity of ores is a very difficult work although the coring depth is shallow, and also the required number of holes is enormous. Conventional drilling/coring method on the ocean is to use drillship. However, the cost is very huge. Recently a new technique has come out which is to use remotely controlled drilling machine on seafloor. This machine seems to have a very good performance. However, it is reported that the available inclination of the seafloor where the machine sits on must be less than 15 degrees. The sea floor inclinations of active hydrothermal vents area are usually very steep and slopes of 45 degrees or more are prevailing and it seems very hard to carry out drilling/coring for the machine at these steep slopes, although it is impossible to mine the ore at these areas because the temperature is too high to work there. The inclination of the sea floor at the dead or paused hydrothermal vents area where ore recovery is possible may be not so steep, and the machine may work well. However, the required number of holes is still a very heavy burden. In order to solve these problems, the author proposes a new concept of drilling/coring system operated from a conventional research ship. This concept is still a desk plan, but the author wants to realize this system at any means.

Jan 1, 2011

By U. Schwarz-Schampera, C. Rühlemann, H. -R. Kudrass

Within 2006 BGR will conclude a contract with the UN International Seabed Authority (ISA) for the exploration of polymetallic nodules. The contract covers an area in the Pacific nodule belt between the Clarion and Clipperton fracture zones, that which is about 75.000 km2 in size at water depths between 4200 and 5000 m (see Fig. 1). Up to now, 7 consortia or state parties have acquired similar exploration “licenses” for polymetallic nodules in the central Pacific Ocean and the Indian Ocean. These licenses of the UN authority are required according to the UN convention on the law of the sea (UNCLOS) as the areas of interest are located outside of national EEZs. The “licenses” then reserve exclusive rights to the applicant for a time span of about 15 years.

Aug 24, 2006

By Rahul Sharma

Although, mining of minerals such as polymetallic nodules and sulphides from the deep sea floor has been delayed due to the combination of factors such as current availability of Cu, Ni, Co, Mn (and other metals) on land and their fluctuating prices; these deposits are still considered as the alternative source for metals in the 21st century. Exclusive rights for exploration in the ?Area? (beyond the national jurisdictions of any country) given to eight countries and consortia by the International Seabed Authority and the estimated resource of 300 million tonnes in a typical area of 75,000 km2 is expected to yield about $17.5 billion (at December 2008 metal prices) in 20 years life span of a single nodule mine-site. In order to recover 3 million tonnes of nodules, an area of 300 sq km only will be mined annually (i.e. <1 km2/day) for an optimum abundance of 10 kg/m2. However, during mining, large quantity (22 tonnes/day) of sediments associated with nodules would be resuspended that could lead to certain environmental impacts on the benthic ecosystem. Several small-scale benthic impact experiments in the Pacific and Indian Oceans, have given some insight into the possible environmental impacts and the restoration processes, but the possibility of extrapolating these findings to a commercial mining scale remains an issue to be considered. An estimated capital expenditure of $1.05 billion and operating expenditure of $4.2 billion for a single deep-sea mining venture will have to be weighed against the availability of mineral ores on land as well as the metal prices in the world market. None-the-less, development of technologies for mining and metallurgical processing, as well as formulation of regulations and guidelines for potential ?contractors? to mine these minerals have been progressing consistently. These coupled with recent efforts by certain ?entrepreneurs? to initiate mining of seafloor massive sulphides in the EEZ of certain countries, indicate the continuing interest and support the perception that such deposits could well be the future sources of metals. This paper analyzes the current status and discusses the economic, environmental, and technical issues that need to be addressed for sustainable development of deep-sea minerals.

Jan 1, 2010

By Kaihui Yang

Volcanogenic massive sulfide deposits are generally considered to have been formed by hydrothermal fluids that leach ore metals out of footwall rocks. However, the necessity for a metal-rich magmatic component in the ore-forming fluid of "giant" ore deposits has been debated over the decades. The solution to this issue is important not only for metallogenic models but also for the mineral exploration. In the hydrothermal leaching model, massive sulfides at mid-ocean ridges are deposited from hydrothermal fluids containing 80 ppm Fe, 6 ppm Zn, 2 ppm Cu, 350oC, and 0.7 g/cm3 density (average data for 21oN East Pacific Rise). A simple calculation demonstrates that such a dilute fluid is unlikely to have been responsible for the formation of the largest ancient massive sulfide ores of greater than 100x106 tonnes, such as Kidd Creek, Brunswick No. 12, Neves Corvo, and Rio Tinto. For such a deposit consisting primarily of pyrite, sphalerite, galena and chalcopyrite (other minerals, including gangue, might account for an additional 10-20%) and even assuming 100% precipitation and retention of the sulfides, more than 790 km3 of vent fluid would be required. For typical water-rock reaction ratios of about 2, this fluid would have to have reacted with about 395 km3 of rock to acquire its metals by conventional leaching processes. This estimate, however, conflicts with the observation that even a giant massive sulfide ore body is usually underlain only by a few cube kilometers of obviously altered rocks. Moreover, this model is not consistent with the observation of hanging wall alteration in many large massive sulfide deposits. The close spatial association between massive sulfides and volcanic rocks, in both ancient and modern sea floors, suggests that direct magmatic contribution should be taken into account in the genetic model. Magmatic fluids, capable of carrying abundant ore metals and volatiles and escaping from magma by depressurization, are well known from modern active volcanoes on land. High concentrations of metals occur in CO2-rich magmatic fluid trapped in felsic volcanic rocks nearby large presently-forming VMS deposits in the eastern Manus Basin (Pacmanus, Suzette) and also in the footwall rocks of Ordovician giant Brunswick #12 deposit in the Bathurst district, New Brunswick. Only 1% of such metal-rich magmatic fluid mixed with heated sea water, that has leached its metals from rocks, would contribute 85% of the total metals to form an orebody. Such magmatic fluids are most likely to be formed from volatile-rich felsic magmas that are prevalent in back arcs, and, if added to the normal circulation system, the fluids could be responsible for the formation of "giant" ore deposits. If this is true, then the study of magmatic fluids in the seafloor volcanic rocks may provide criteria for the exploration of large ore deposits.

Jan 1, 2011

By H. Oda, L. E. Fong, K. K. McBride, B. P. Weiss, F. J. Baudenbacher, A. Usui

Fine-scale dating is a key parameter in characterizing the growth history of hydrogenetic ferromanganese crusts. We once compared several dating methods, micropaleontological (calcareous nanofossil), radiometric (10/9Be), and paleomagnetic (step-wise measured inclination) methods on single samples, but these independent methods were not consistent with each other (Joshima & Usui, 1999). For example, a 4-cm thick crust was dated as 3Ma by the fossil-paleomagnetic combined method, while it dated older than 5.5 Ma by Be-10 dating. This discrepancy suggests a question if the Be-10 radiometric method can give us false ages or growth rates (Usui et al., 2002) because of post-depositional change, diffusion or other reasons. In order to answer the question, we conducted ultra-fine magnetostratigraphy with a SQUID microscope on the same hydrogenetic Mn crust sample. Rock magnetic measurements revealed that the main magnetic mineral is well dispersed single domain grains, which is typical to magnetite but not yet specified (Oda, 2005).

Aug 24, 2006

By Igor E. Mikhaltsev

This paper concerns the continuation of work on the deepwater non-oxygen cycle heat energy generating systems. The 25-kW prototype of a universal deepwater turbine-electric energy source with hydrazine-hydrate as the primary heat production chemical is described in short and its abilities are discussed. The ?hydrazine-hydrate 64? is a catalytically dissociated heat production chemical (H2H4 ? nH2O) with 36% of water. The system was designed for work in any depths of the ocean down to 6000 m. It was built and tested working in the testing chamber in the ambient hydrostatic pressure of 600 bar. Then it was tested in the autonomous programmed regime in the Atlantic Ocean. The privileges of that energy system for any bottom installations or moving devices designed for ocean mining which need high power energy sources (20-100 kW and more) are discussed. The important needed step forward is raising the efficiency of the system which needs some investigation work in known directions. It is supposed that the possibility of getting about 5 kg/kWh with improved battery charging possibilities could be achieved. This might make the system even more profitable for mining operations.

Jan 1, 2001

By Daisuke Monoe, Kisaburo Nakata, Rika Takeuchi, Tetsuo Yamazaki, Tomoaki Oomi, Tomohiko Fukushima

There are generally two methane passes in conjunction with the seafloor natural cold seepages, as is schematically shown in Fig. 1. The first pass consists of the coupled anaerobic oxidation of methane and anaerobic sulfate reduction, as well as sulfur oxidation in the bacterial mats and immobilization thereafter in the sediment layer and on the seafloor. Through the first pass, calcium and organic carbonates are formed in biological and chemical processes from the methane (Luff and Wallmann, 2003; Luff et al., 2004). The detailed structure of the seafloor methane consumption process unit and its biological and chemical processes were introduced in Yamazaki et al. (2005). The other pass consists of direct bubbling into the water column. Through this pass, organic carbonate is formed with biological oxidation, and a small amount of the methane escapes into the atmosphere. Methane flux is supplied to these two passes through the sediment layer from the deeper structures. The structure of the methane supply process unit was introduced in Yamazaki et al. (2006).

Sep 24, 2006

By Tetsuo Yamazaki

Manganese nodules on deep ocean floors have continuously received attention as potential sources for strategic metals such as Co, Ni, Cu, and Mn, due to their vast distribution and relatively higher metal concentrations (Mero, 1965; Cronan, 1980). Several registered Pioneer Investors have already identified promising sites in deep-sea regions for manganese nodule mining (ISA, 1998), and appropriate mining technologies have been developed during the last thirty years by the international consortium and several nations (Welling, 1981; Kaufman et al., 1985; Bath, 1989; Charles et al., 1990; Yang and Wang, 1997; Yamada and Yamazaki, 1998; Hong and Kim, 1999; Muthunayagam and Das, 1999). The mining feasibility for manganese nodules, including an economic evaluation, has been examined in detail by some researchers (Andrews et al., 1983; Hillman and Gosling, 1985; Charles et al., 1990; Soreide et al., 2001).

Jan 1, 2011

By Jung-Hoon Kang

Present study was stemmed from the survey associated with deep-sea mining in the KODOS area between Clarion Fracture Zone and Clipperton Fracture Zone located in the North Pacific Ocean. The study area, which is located in the southeastern part of North Pacific gyre, is oligotrophic waters with low nutrients and chl-a concentrations below 1µg/l (MOMAF, 1996). This area is also characterized by divergence at 8°N and convergence at 6°N, which moved northward or southward in the range of a few kilometers with seasonal and climate changes. If the waste materials related to deep-sea mining are intruded into the surface waters continuously, unexpected effects to water column ecosystem are anticipated negatively. In order to assess the impact on the planktonic ecosystem, natural variation need to be distinguished from anthropogenically induced variation in terms of the abundance and species composition of plankton. In this study, mesoscale variation of zooplankton community was reported in relation to the physical conditions in the northeastern Pacific during 1998 and 1999. Temperature and salinity were determined using a CTD from surface to 200m depth in July 3-20, 1998 and in June 22-July 1, 1999. Zooplankton samples were collected from two different depths (0-50m, 50-200m) by vertical towing using an opening-closing net (100cm diameter and 300 µm mesh size). The samplings were carried out at every one degree between 5° and 12°N (1998), between 5° and 11°N (1999) along the meridional lines of 131°30´ W. The net was lowered to the depth of interest from a stationary research vessel and towed upward to collect zooplankton at a speed of 25~30 m per minute. Zooplankton samples were transferred to 1-l sampling bottles and immediately fixed with neutralized formalin into the final concentration of 5%. Considering the characteristics of zooplankton such as diurnal vertical migration, all samplings were done during the nighttime. The volume filtered by the net was calculated from the readings of flow meter (Hydro-Bios Model 438-115). Zooplankton were identified to the genus level and enumerated under a microscope. The abundance of zooplankton at each station was expressed as the numbers/100 m3.

Jan 1, 2003

By Alexander Malahoff

Six active Kermadec Arc submarine volcanoes located between 34°S and 36°30?S were mapped and sampled by an interdisciplinary inter-institutional research team between April and July 2005 using submersibles Pisces V and Pisces IV aboard the mother ship the RV Kai?mikai-O-Kanaloa. The purpose of the expedition was to study the relationship between hydrothermal activity, formation of hydrothermal mineral deposits and the biodiversity of life associated with the hydrothermal vents. Of the volcanoes examined, all showed evidence of hydrothermal activity, plume production and helium anomalies. Only two of the volcanoes, namely Brothers and Clark, showed chimneys and surficial poly-metallic sulphide deposition. Hydrothermal venting at a water depth of 1700 meters within the base of the northern wall of the summit caldera of Brothers Volcano has produced a field of chimneys, some of them 5 metres high with black smokers venting. Temperatures of 300°C were measured within the active vents. Clark Volcano has a double cone summit at a water depth of 875 metres. The shallowest cone has a near-summit hydrothermal vent field with 5-meter high venting chimneys and smaller structures around the periphery. Water temperatures of 200°C. Geochemical and petrological analysis of the massive poly-metallic sulphide samples taken from Brothers and Clark show a diversity of mineralogy. This diversity is clearly a function of hydrothermal water temperature. Chimneys sampled from Brothers are pyrite and sphalerite dominant with lesser chalcopyrite. Sulphides from Clark Volcano tend to be barite rich with lesser sphalerite and pyrite. Sulphides from Brothers Volcano have a range in gold composition of 4 to 58 ppb with silver composition of up to 38 ppb. A mineral formation model for the volcanoes suggests hydrothermal fluid boiling within the volcanic edifice for those volcanoes with shallow summits and massive sulphide deposition with the edifice as well. Surficial deposits include native sulphur and lower temperature oxides. Only the deeper water Brothers Volcano shows massive sulphide deposition along the marginal faults of the caldera floor.

Jan 1, 2005

By Cornel E. J. de Ronde

Brothers volcano (34°51.7?S, 179°03.6?E) is a large caldera volcano that forms part of the active Kermadec arc south of 32° S, NE of New Zealand. It is an elongate edifice striking NW-SE that is ~11-13 km long by 7-8 km across. The caldera has a basal diameter of 3-3.5 km and is surrounded by 350-450 m high walls with the floor 1,850 m deep. A volcanic cone of dacite composition rises 350 m from the caldera floor and partially coalesces with the southern caldera wall. Much of the caldera construction and the location of the hydrothermal vent sites are controlled by intersecting basement structures. Three hydrothermal sites have been recognized at Brothers; NW caldera, SE caldera and cone. Multiple hydrothermal plumes were mapped from the bottom of the caldera upwards to a depth of 900 m and originate from two of the sites; one on the NW caldera wall the other atop the cone. Analyses of these plumes show that the two vent sites are chemically distinct. The cone site itself hosts three distinct vent fields (summit, upper flank, NE flank) that in 1999 had plumes (mainly from the summit) containing relatively high concentrations of gas with a shift of -0.27 pH units (proxy for CO2) and H2S concentrations up to 4,250 nM, particulate Cu (PCu) of 3.4 nM, total dissolvable Fe (TDFe) of 4,720 nM, TDMn up to 260 nM and Fe/Mn values between 4.4 and 18.2. However, in 2002 plumes from the summit vent field had noticeably lower concentrations of PCu (0.3 nM), TDFe (175 nM), and Fe/Mn values of 0.8, although similar TDMn (220 nM) and shift in pH (-0.22) suggesting a state of flux for this site. By contrast, plumes originating from the NW caldera site have much less gas with a pH shift of -0.09 units and no detectable H2S, TDFe up to 955 nM, TDMn up to 150 nM, and Fe/Mn values of 6.4, and have not changed their composition over the same three year interval indicating a more chronic hydrothermal system. Plume d3He results show helium is decoupled from more near-surface vent fluid sources although a shift in R/Ra values from 6.1 ± 0.5 in 1999 for the combined vent sites to 7.2 ± 0.1 in 2002 indicates a less radiogenic input of helium over three years, suggestive of a greater magmatic input to the system.

Jan 1, 2004

By Fernando J. A. S. Barriga

"Recent concerns over the availability of many mineral raw materials, and newly available technological developments, produced renewed interest in deep-sea mining. However, environmental concerns, with variable degrees of justification, are raising opposition to the concept. The forecast for the behavior of consumption versus availability of many raw materials, nearly all critical metals, arguably show that consumption will grow much faster than resource discovery onshore. Finding new sources of raw materials seems inescapable. The deep seafloor stands out as the only likely candidate.Sea Floor Mining and the EcosystemMarine mining has already started, decades ago, for diamonds, currently up to depths near 400m. Although the industry recognizes there is a footprint, it considers the footprint quite minor, because the area mined is small: in Namibia, where offshore diamond mining is now 70% of the country’s total, only 3% of the concession of 3,700 sq miles (9600km2) have been mined. As plans to mine deep-sea massive sulphide deposits and polymetallic nodules progress, the environmental concerns grow. Some of these concerns are as follows:?The deep-sea ecosystems are composed of long-lived species, with low rates of reproduction. The environment may not recover from mining on a human time scale;"

Jan 1, 2017

By Thomas Pichler

In the past marine mining technology has focused on bulk mining of base metals from polymetallic massive sulfides. This has not been very successful because of the relatively low unit value of these metals and other reasons such as water depth, etc.. The process of gold enrichment in hydrothermal deposits is controlled through five different factors: (1) nature and source of the solution, (2) source of the gold, (3) a mechanism for mobilizing and transporting, (4) a mechanism for deposition, and (5) a mechanism to preserve the deposit. Gold has been identified in marine polymetallic massive sulfides from various locations on the ocean floor (e.g., spreading centers, seamounts) with contents ranging up to 5 ppm Au. This is within the current range of 1.0 to 7.0 ppm gold content which classifies gold ores. The gold appears to have been derived during hydrothermal alteration of the oceanic crust. Until the present there has been little attention to the possibility of mining gold or other precious metals in the marine environment. However, the magnitude of hydrothermal alteration (seawater can penetrates to a depth of 5 km into the oceanic crust) and primary gold contents of the rocks in the pathway of the fluid indicates that major gold deposits must have formed on or in the ocean floor, but they have not been found. To find a big deposit might only take an exploration model exclusively designed for gold exploration on the ocean floor.

Jan 1, 1993

By M. Ye. Melnikov

The report is about oceanic ferromanganese crusts ? covers of iron and manganese hydroxides developed over an opened rock of seamounts and rises. Ore bed parameters of crusts are understandable as their thickness and content of main economic components ? manganese, cobalt and nickel. All known results of research activity on ferromanganese manganese crusts point to that crust are characterized by notable variability of thicknesses and composition. It is possible to separate few levels of variability. The most evident is the first level of parameters variability, which is manifested in various regions of the Ocean, and connected first of all, with an age of submarine mountains, a host objects for a crusts. It was proved by many authors, that most powerful crusts are connected with submarine mountains of Cretaceous age. [1]. Crust thickness at the Magellan Seamounts reaches, for example 12-15 cm, sometimes exceeds 20-22 cm. Thicknesses of Hawaii Archipelago or Tuamotu crusts in 3-4 times less. Biostratigraphy studies of crustal sections at the Magellan Seamounts already show, that its main part started to form in the Late Paleocene. Four layers with well expressed features in structure and composition of a layer are separated in the section. From foot to top: Late Paleocene ? Early Eocene layer I-1, Middle-Late-Eocene layer I-2, Miocene layer II and Pliocene ? Quaternary layer III. Relics of more ancient Campanian ? Maastrichtian ore layer [2, 4] were discovered. It is evident for example, that Oligocene mountains could not be a host for two lower layers in the crust section.

Jan 1, 2010

By M. Ye. Melnikov

The report is about oceanic ferromanganese crusts ? covers of iron and manganese hydroxides developed over an opened rock of seamounts and rises. Ore bed parameters of crusts are understandable as their thickness and content of main economic components ? manganese, cobalt and nickel. All known results of research activity on ferromanganese manganese crusts point to that crust are characterized by notable variability of thicknesses and composition. It is possible to separate few levels of variability. The most evident is the first level of parameters variability, which is manifested in various regions of the Ocean, and connected first of all, with an age of submarine mountains, a host objects for a crusts. It was proved by many authors, that most powerful crusts are connected with submarine mountains of Cretaceous age. [1]. Crust thickness at the Magellan Seamounts reaches, for example 12-15 cm, sometimes exceeds 20-22 cm. Thicknesses of Hawaii Archipelago or Tuamotu crusts in 3-4 times less. Biostratigraphy studies of crustal sections at the Magellan Seamounts already show, that its main part started to form in the Late Paleocene. Four layers with well expressed features in structure and composition of a layer are separated in the section. From foot to top: Late Paleocene ? Early Eocene layer I-1, Middle-Late-Eocene layer I-2, Miocene layer II and Pliocene ? Quaternary layer III. Relics of more ancient Campanian ? Maastrichtian ore layer [2, 4] were discovered. It is evident for example, that Oligocene mountains could not be a host for two lower layers in the crust section.

Jan 1, 2010

By Sup Hong

A pilot mining robot, named MineRo-II, has been developed by KIOST during 2011-2012. The pilot scale was defined as 1/5 of the commercial mining capacity, 1.5 million dry-tons of nodules per year. The development purpose of MineRo-II is to use for the pilot mining test planned in 2015. MineRo-II was designed to be self-propelled by electric-hydraulic power and remotely operated in real-time from aboard. The main operational functions are crawling on seafloor, pick-up and crushing of nodules, discharging nodules out to buffer. Prior to MineRo-II, a test miner (MineRo-I) was developed in scale of 1/20th in 2007, and performed two times sea trials in 2009 and 2010. The results of performance tests were evaluated and utilized for the concept of MineRo-II. The design concept aimed at the expandability of the mining capacity based on modularity of configuration, maintenance simplicity and multiplicity of backup solution. The pilot-scale mining capacity is achieved by four pick-up modules of each 1m wide, which are moving forward with robot vehicle and sweep the nodules entering below the pick-up heads. Principally, by adding the pickup modules in lateral dimension the mining capacity may increase linearly. MineRo-II was designed and constructed in unit-module wise. The robot consists of two unit-modules having an identical mechanical and hydraulic configuration. Each unitmodule has two tracks, two pick-up devices with attitude control devices, two crushers, one discharge pump, and one hydraulic system. Two unit-modules are connected by one loading frame and integrated by electric-electronic system. Two thrusters for control of the

Sep 14, 2011

By Peter M. Bartlett

The Republic of South Africa ranks among the world leaders in both reserves and production of numerous land-based mineral commodities. Over the last three decades, however, South Africa has also identified several commodities that may exist in commercial quantities in the marine environment. The major targets include 1) placer diamonds; 2) titanium- and zirconium-rich beach sands; 3) sedimentary and concretionary phosphorite and glauconite deposits; 4) manganese nodules; and 5) hydrocarbons. South Africa ranks second in world reserves of diamonds and has potentially enormous sea resources. Diamonds are currently recovered on the Atlantic side from ancient beach gravels in the Northwest Cape Province and from the seabed south of the Orange River to Lamberts Bay. Approximately 100,000 carats (or just 1% of South Africa&apos;s total annual production) are produced each year from offshore operations. DeBeers is investing approximately $5 million per year on sea prospecting activities and currently operates three vessels in offshore recovery operations. Diamonds recovered at sea will remain a small percentage of total production because of huge land-based reserves that are mined at a fraction of the cost of seabed operations.

Jan 1, 1986

By Audrey Boissier, Marie-Anne Camon, Cecile Cathalot, Yves Fouquet, Laurent Bignon, Arnaud Agranier, Ewan Pelleter, Sylvain Bermell, Florian Besson

INTRODUCTION In October 2014, on behalf of the French government, Ifremer, along with the International Seabed Authority (ISA), signed a contract to start a detailed exploration program for seafloor massive sulfide (SMS) deposits in the work plan located on the slow spreading Mid-Atlantic ridge (MAR). The contract has a fifteen-year lifetime and the related exploration program must include the outline of SMS deposits and a resource assessment, as well as detailed environmental base line studies in the contract area. The exploration for SMS deposits generally includes detection of hydrothermal plume anomalies, acquisition of surface and near-bottom geophysical data, sampling operations from the research vessel (e.g. dredges, cores), and dive operations. The environmental studies include, among others, short and long-term oceanographic measurements, water column studies, biodiversity evaluation close and far from SMS deposits, characterization of natural hydrothermal plumes and related sedimentation. The HERMINE research cruise held from March 13th to April 28th 2018 (R/V Pourquoi Pas?) was the first cruise dedicated to exploration of active and inactive SMS and to the quantification of natural chemical input to the water column. The HERMINE cruise strategy was built up around three main objectives: (i) regional exploration including the detection of plume anomalies and the research of SMS deposits, (ii) local exploration of a SMS district and (iii) integrated study of a natural hydrothermal plume. This 3-in-1 cruise required us to optimize the switch between dives and surface operations. Day-time was devoted to dive operations whereas night-time was mostly dedicated to CTD/Rosette operations. The Nautile HOV (Human Occupied Vehicle) was well suited to the working time schedule of the cruise because it was time efficient in shorter (i.e. < 10h) dives due to fast descent and ascent speed, fast submerged forward speed, high maneuverability and the ability to carry heavy science payload as well as large volume of samples. Regional Exploration The first seventeen days of the HERMINE cruise were devoted to regional exploration, i.e. the detection of new plume anomalies and the research of new sulfide mineralization in the French work plan (10 000 km2; 6 clusters).

Jan 1, 2018

By Mikhail D. Ageev

The paper concerns with some questions of Autonomous Underwater Vehicle (AUV) control system design, which allows a motion at rough undersea terrain. The AUV advantages reveal itself completely during exploration of such objects as seamounts and reefs area. These objects are characterized by steep slopes (30 degrees and above) and chaotic situated obstacles (rock debris, pinnacles, escarpments). Uses of other technical facilities for operating in such formations are difficult, dangerous or impossible. These regions take an interest due to the presence of iron-manganese crusts. Modern AUV can estimate density of mineral by means of still camera or video recorder. For this reason the vehicle has to move with the distance of 3-5 meters from seabed. Under such conditions micro- and mesorelief presents a considerable danger for AUV. The AUV can bypass underwater obstacles in the various ways. However, in any case AUV motion will be characterized by intensive maneuvering on various speeds (from 0 up to 1.5 m/s), circular change of tractive force vector and, hence, a circular flow about the hull. So, AUV is equipped with the propulsion system, which provides free modes of motion.

Jan 1, 2003

By Jai-Woon Moon

Lemkein seamount located in the west of the Kuwajleen Atoll of RMI is a relatively samll, simple-shaped, peaked type seamount with its base at 4,500 m and summit at 1,452 m water depths. Ferromanganese crusts were identified in the water depth range between 2,000 m and 2,500 m, and they were mostly observed on the northern slopes of the seamount. Among various substrate rocks, breccia occurred most commonly with crusts and formed the thickest crust layers. Average thickness of the Lemkein crusts was about 5 cm. Their chemical compositions were similar to other crusts found in the RMI area; Mn=25.82%, Fe=15.29%, Co=0.74%, Ni=0.56%. Lemkein crusts were characterized by their four distinctive internal layers; 1) Massive Layer 1; 2)Porous, Fe-stained or sediment infilled Layer 2; 3) Massive to slightly porous Layer 3; and, 4)Massive, Dense, Phosphotized, CFA veined Layer 4. Layers 1 and 2 were generally similar in composition, but highest Co concentrations were measured in Layer 1 while relatively higher concentrations of Al, Rb, Fe, and Ti were observed in Layer 2. Layer 3 showed higher concentrations of Ca and P than Layers 1 and 2. Based on the Co-chronography, the age of Layer 1 is 0¡?6 Ma (growth rate = 1.50 mm/Ma), Layer 2 is 6¡?15 Ma (1.75 mm/Ma), Layer 3 is 15¡?27Ma (1.76 mm/Ma), and Layer 4 is 27¡?45 Ma (2.06 mm/Ma). These preliminary results indicated that high Co contents in Layer 1 resulted from slow growth rates; Layer 2 was formed under relatively strong influence of high terrestrial input; and, Layer 3 was probably affected by a minor phosphatization event occurring in 15 Ma.

Jan 1, 2000