Search Documents

By Gregory J. Kurras

In 1995 the Marine Minerals Technology Center (MMTC) of the University of Hawaii conducted a sidescan sonar survey and sampling expedition of the submarine geology and hydrothermal systems surrounding the active volcano White Island. The island is located in the Bay of Plenty, within the geothermally active Taupo Volcanic Zone off-shore of the North Island of New Zealand, and is the site of numerous shallow-water hydrothermal systems. The survey system, an EdgeTech DF1000 sonar, was a dual frequency 100 kHz & 500 kHz sonar capable of imaging the seafloor at better than 1 m resolution and possibly detecting gas bubbles within the water column. Sidescan imagery clearly shows sand channels, debris slumps, submarine landslides, and volcanic ridges all around the island to roughly 800 meters offshore. However, analyses of the both raw and processed acoustic data indicate that the sonar was not able to image any of the shallow-water hydrothermal gas seeps known to exist around the island. Vents were located using a commercial fish finder and knowledge from local tour guides and divers. Eleven gas samples from three different sites were collected by divers for analysis of chemical and isotopic composition. Rock samples were collected from thirteen underwater outcrops for correlation with existing data on subarial island flows sampled by previous investigators. Thin sections and XRF analysis were done for each rock to determine mineral assemblages along with major and trace elements, which were used to tie submarine samples to specific subarial stratigraphic layers.

Jan 1, 2011

By Arturo Carranza Edwards

Sedimento II oceanographic cruise, on board of the B/O El Puma, shows a new high anomaly or phosphate associated with shelf sediments from the south Mexican Pacific. Recently, were found two anomalies in the Gulf of Tehuantepec, that are located to the east of this new anomaly, that is related to muddy sands and rock fragment debris. The latter shows values of 17% P205. The phosphate occurrence is probably associated with red tides locations that usually are found in sites where sediments are phosphates enriched. These findings suggest that south Mexican Pacific is of potential interest for P205, in waters with high nutrients values. The possibility of a more regional occurrence of phosphate, from California to Chile is suggested.

Jan 1, 2000

By Grigori Abramov

As we enter into the 21st Century, miners are looking more attentively at new mining technologies allowing decrease environment damage along with operational cost. This technic would allow developing of poor and difficult mineral deposits, including the World Ocean offshore zone. Borehole Mining is an underground/underwater remote method of mining carried out from floating platforms or vessels. Definition of Borehole Mining (BHM), working schematic, main technical data and its advantages are given. The method is currently in use in mining of different type of raw materials, such as: uranium, iron ore, quartz sand, coal, polymetallic ores, phosphate, gold, diamonds, rare earths, amber and more. It is also in use in oil and gas stimulation, salt domes storages building and environmental problems solution. Recently recorded data of Borehole Mining productivity (80-100 t/hour/hole) and a depth of mining (over 1 km) has been achieved in a last couple years. Remoteness of method not only secures complete safety of operations but also allows wide sector of underwater applications. The World leaders in Borehole Mining are Russia and the United States. Based on previous experience the Universal Tool for Seabed Borehole Mining has been developed for wide sector of usage: from exploration and mining - through oil & gas stimulation to souterrain storages construction and lake's bottom cleaning.

Jan 1, 2000

By Nicholas Dyriw, Georgy Cherkashov, Tamara Stepanova, John Parianos, Anna Firstova

"Seafloor massive sulfide (SMS) deposits are a new frontier in global metal resources. Hydrothermal chimney’s (black smokers) precipitate Cu, Zn, Ag and Au rich from hot fluids (>250°C) during interaction with cold seawater ~2-4°C. Here we compare the sulfide mineralogy and geochemistry of Cu-sulfide chimney samples from two different tectonic locations: Solwara 1, a Cu-rich, transitional arc-back arc (Arc-BA) type SMS ore deposit and; Ashadze-1, a Cu-rich, ocean ridge type SMS deposit (Hannington et al., 2011).This work represents the first stage of a project aimed at investigating and understanding the significance of high Cu concentrations in SMS systems. Comparing these particular systems is significant because they share critical similarities despite being located at different seafloor depths, hosted in different rocks and are located in two different endmember tectonic environments. Critical similarities include: 1) age of mineralization, ~6000 years to current (Firstova et al., 2016; Johns et al., 2014); and 2) high copper contents, with chalcopyrite dominating sulfide mineralization (Firstova et al., 2016; Lipton, 2012). The reason for high Cu concentrations in both of these locations is still not entirely understood. The youthfulness (<6000y to current) of both locations is important because it reduces the possibility of increased zone refining, allowing us to understand the source characteristics better. This research will advance our understanding of the copper systematics of SMS systems by investigating and comparing the mineralogical and geochemical signatures from two, Cu-rich, end-member type SMS sites."

Jan 1, 2017

By Steve Potter

"REVIEW OF ISA's DRAFT EXPLOITATION REGULATIONS – HAVE KEY STAKEHOLDERS' CONCERNS BEEN ADDRESSED ADEQUATELY?In early August 2017, the ISA published a revised draft of the exploitation regulations. My presentation will focus on the extent to which key State and Contractor issues raised in formal submissions in November 2016 have been addressed in the revised draft and any additional key issues in the revised draft which are likely to cause significant concern for Contractors.ABSTRACTFollowing the ISA's call for submissions in response to draft zero of the exploitation regulations in July 2016, 43 responses from stakeholders were received by the ISA in November 2016. My presentation will start by briefly looking at how the ISA has continued to engage with stakeholders following the publication of draft zero of the exploitation regulations, including at payment regime workshops in London (November 2016) and Singapore (April 2017) and at the environmental workshop held in Berlin in March 2017. It will also touch on the publication in February 2017 of what was in effect a very preliminary draft of the environmental regulations before moving on to consider in detail the extent to which key State and Contractor issues have been addressed in the ISA revised draft exploitation regulations which were published in August 2017. My review of the formal submissions will include, amongst other things, commentary on:(i) the level of Stakeholder response (State Parties to UNCLOS, Sponsoring States, Privately owned Contractors, State Owned Contractors and NGOs);(ii) the quality of the submissions (particularly by States and Contractors); (iii) the key concerns raised by State and Contractor stakeholders and how those issues have been addressed in the revised draft exploitation regulations; and(iv) how all stakeholders need to further engage with the ISA to ensure that the exploitation code adequately addresses the legitimate and reasonable concerns of each Stakeholder group (e.g. Contractors, Sponsoring States, Developing States and NGOs)."

Jan 1, 2017

By David M. Holmes-Smith

Many attempts have been made to design and build an AUV that is small, meets the sensing objectives and is cost effective. Many inventors have already designed smaller vehicles but the problem observed is an increased vehicle instability resulting in instrument instability where data gathered is not trustworthy. Additional problems include instrument weight to vehicle weight ratios and the lack of space for power storage and electrical components. The UFOceanic seeks to remedy these concerns by employing a completely different design and propulsion system. Still in the design stage ? now with a mock-up unit for testing, the results are encouraging. We have chosen a very low voltage embedded systems design using multiple PIC processors and fuzzy logic programming. We are designing the craft to rotate for stability and to provide friction reduction to minimize the need for instrument stability compensation and propulsion power. Additionally, we are looking and experimenting with a number of power plant drive systems including flywheels, GNP (plasma), fuel cells and more conventional systems. We of course plan for the UFOceanic to run for months at a time supported by a self-charging system.

Jan 1, 2001

By T. Yamazaki, T. Goto, R. Arai, N. Nakatani

The importance of cobalt-rich manganese crusts on the Pacific seamounts for possible future rare metal sources has been recognized these 30 years. The thin layer-type coverage and the micro-topographic undulation of basement affect not only the excavation efficiency but also the economy of mining venture. Because of these distribution characteristics, no economic feasibility has been recognized through the past economic analyses. On the basis of a recent geological study about seamount rocks, a possibility of by-product substrate recovery for phosphorous supply with cobalt-rich manganese crust mining has been highlighted. In the mining model, the substrate rocks are utilized as phosphates for agricultural and chemical usages. Under some preliminary technical and economic assumptions, the possibility of cobalt-rich manganese crust mining venture is examined. The results show a better economy of the venture including the substrate rock usage for phosphorous supply. Introduction Cobalt-rich Manganese Crusts and the Economic Feasibility Cobalt-rich manganese crusts on the Pacific seamounts received attention as potential sources for strategic metals such as Co, Ni, Cu, and Mn, due to their vast distribution and higher cobalt concentration than manganese nodules (Cronan, 1980; Halbach, 1982; Manheim, 1986). In the earlier stage, the geological distribution characteristics were reported (Cronan, 1984; Clark et al., 1984; Misawa et al., 1987; Pichocki and Hoffert, 1987) and a systematic feasibility of the mining was studied (Hawaii DPED, 1987).

Jan 1, 2018

By Lorena Blanco, Guillermo Gómez-Ramos, Iker Blasco, Egidio Marino, Luis Somoza, Ricardo León, Teresa Medialdea, Javier González

"This study presents the first catalogue of marine mineral deposits and energy resources along the continental margin of Spain. Aggregates, oil and gas and metalliferous mineral areas have been defined and mapped. The catalogue, implemented in a geographic information system (GIS), is conceived as a first national database within the European network, which is being built as part of the EMODnet-Geology project. It comprises 8 types of mineral and energy resources for the Spanish margins: aggregates, hydrocarbons, evaporites, placer deposits, phosphorites, polymetallic sulfides, polymetallic nodules and cobalt-rich ferromanganese crusts (Figures 1 and 2). The catalogue stores a total of 409 marine mineral deposits and compiles information such as name, deposit type, main morphology, main minerals, setting or area extent for each mineral deposit. By number of deposits compiled, the aggregates are the most abundant (286) followed by hydrocarbons (62), cobalt-rich ferromanganese crusts (32), evaporites (9), placer deposits (8), phosphorites (5), polymetallic nodules (4) and polymetallic sulphide deposits (3). Considering the total extension, hydrocarbons (32,386 km2) and cobalt-rich ferromanganese crusts (24,951 km2) represent the biggest areas.The Geological Survey of Spain (IGME) is developing a new tool in the catalogue, according the International Seabed Authority (ISA) Database parameters, for individual samples on each ferromanganese deposit. The database includes an extensive collection of records that comprise five information groups: general cruise and sample data, physical properties, mineralogy, geochemistry and acronyms used. New attributes have been incorporated, in example: geophysical, sedimentological and petrological data in the deposit area, sample weight, porosity, morphology, textural and structural features, geochemistry of major, minor and trace elements (included REEs and PGEs) and supplementary cruise and laboratory reports. This new database complements the EMODnet-Geology project minerals catalogue, offering a deeper level of information for the areas with major potential for mineral or energy resources as they are the Canary Island Seamount Province, the West Margin of Galicia and the Gulf of Cadiz."

Jan 1, 2017

By Ian Selby

Resource management is a key factor in the operation of a successful marine aggregates business; it is integral to the development of sustainability, satisfying increasing commercial, quality, and environmental performance standards. Resource management is based on the combination of; (i) a thorough evaluation and understanding of the resources on the sea bed and (ii) a dredging plan targeted to permit the effective and efficient extraction of the resources whilst mitigating impacts and leaving the sea bed ready for recolonisation.

Jan 1, 2004

By A. M. Olivarez

The elucidation of the theory of plate tectonics has provided a conceptual framework for understanding the formation and distribution of different types of ore deposits. For example, we now recognize that certain kinds of mineral deposits are generally associated with a particular type of plate boundary (i.e., massive sulfides often occur along divergent plate boundaries, whereas porphyry copper deposits are typically found along convergent boundaries). During certain geologic time periods, plate reorganization events have changed the relative proportion of different types of plate boundaries. Corresponding changes have been observed in the abundance and distribution of ores deposited during these times. The present study examines the temporal aspects of this relationship; i.e., do plate reorganization events play an active or passive role in ore formation? In other words, do plate reorganizations simply provide a more favorable tectonic setting in which ore formation can occur over significant time periods, or are they directly linked to the mineralization process? We have examined this question by comparing regional tectonic histories with the ages of known massive sulfide and porphyry copper deposits. Because these deposits, in particular massive sulfides, form as a result of hydrothermal activity, we have also compared regional tectonic histories with proxy indicators of this process in the marine sedimentary record. These indicators include increased mass accumulation rates of Ca, Fe, Mn, and opal, characteristic changes in the Sr/Ca and Mg/Ca ratios of biogenous carbonates, and shoaling of the carbonate compenstion

Jan 1, 1988

By Gary J. Massoth

Wherever hydrothermal fluids vent from the seafloor they will buoyantly rise (up to 100?s of meters) while mixing with seawater before attaining density equilibrium and dispersing laterally as neutrally buoyant plumes commonly 50 to several 100?s of meters in thickness and with order-of-magnitude or greater breadth. Although these plumes are typically >10,000-fold dilutions of vent fluids they can be reliably detected using sophisticated physical sensing and chemical techniques. Hence, hydrothermal plumes are spatially large targets compared to the actual sites of seafloor fluid discharge and resulting mineralization. For this reason plume prospecting techniques evolved over the past 20+ years have been widely used to systematically explore over 10% of the 60,000-km-long system of mid-ocean ridge (MOR) spreading centers for hydrothermal activity. While plume detection and gradient mapping can be used to home in on venting sites, plume chemical signatures provide additional insight regarding the nature of the fluids being discharged on the seafloor. We have applied the systematic plume prospecting techniques developed on MORs to the volcanic frontal arc setting as part of the NZAPLUME (New Zealand American PLUme Mapping Expedition) surveys. NZAPLUME I in March 1999 marked the first systematic reconnaissance of any intra-oceanic arc for submarine hydrothermal activity. Seven of thirteen previously mapped volcanoes that comprise a 260-km-long section of the southern Kermadec arc northeast of New Zealand were confirmed to be hydrothermally active. On average, one hydrothermally active volcano was found along each 35 km of arc front, a rate comparable to slow- and intermediate-rate spreading MORs. During NZAPLUME II in May 2002, thirteen previously unknown volcanoes and 8 satellite cones were first swath mapped for bathymetric detail and then surveyed using plume prospecting techniques. Three active venting sites were discovered along this 580 km-long arc section, bringing the total to 10, or 39% of 26 volcanoes surveyed overall, still an appreciable frequency rate for venting sites compared to MORs. While only chemical results for NZAPLUME I are available, the arc plumes characterized so far are chemically diverse and rich compared to MOR plumes. This diversity and enrichment was most evident as ultra-high concentrations of CO2, sulfur gases (St = SO2 + H2S), and Fe within plumes over several volcanoes. We suggest the fluids discharging from the seafloor at these sites are volcanic fluids, i.e., hybrid fluids comprised of MOR-like hydrothermal fluids evolved from seawater-rock reaction and fluids exsolved from magma as acid volatiles and liquid brines.

Jan 1, 2002

By D. S. Cronan

Based on analogy with the Clarion-Clipperton zone, three main factors appear to influence the occurrence of potentially economic nodules in the study area, (i) elevated biological productivity, mainly above 50gCm-2y-l, (ii.) sea floor depth near or below the CCD, (iii) an absence of turbidite sedimentation. These conditions are fulfilled in parts of the following basins, where available data indicate that high grade and sometimes abundant nodules occur. i) The East Central Pacific Basin west of the Line Islands extending to the East Central Pacific Basin north and east of the Phoenix Islands ii) The West Central Pacific Basin west and northwest of the Phoenix Islands iii) The North Penrhyn Basin north of Penrhyn Island Notwithstanding the similarities between the environmental conditions under which potentially economic nodules occur in the Clarion-Clipperton zone and in the areas listed above, such similarities may relate only to present day conditions. During the possibly long periods of nodule formation, environmental conditions may have varied, and the deposits formed under conditions different from those prevailing at the present day. However, the fact that both present day conditions and the deposits in the two areas do show similarities suggests that applying the same genetic model to them has some validity. Possibly, any changes in environmental conditions during the period of formation of the deposits has been similar in both areas. Such uncertainties can only be resolved by a much fuller evaluation of the evolution of nodule deposits in both areas throughout recent geological time.

Jan 1, 1986

By Olav Rune Godø

We present a science-based infrastructure for continuous online monitoring of the ocean interior including benthic, pelagic and the demersal habitats. It will reduce expensive ship based monitoring costs associated to offshore and coastal industries. We combine established Norwegian cabled observatory technology and German mobile seafloor robotic technology and thus supports the transition from local to spatial ecological monitoring. Both technologies are developed through science - industry partnerships. In Norway, the Institute of Marine Research has worked with Statoil ASA and Metas AS to install and operate the LoVe cabled observatory. The German technology is developed by iSeaMC and Kraken Robotik, two spinoff enterprises of the Helmholtz Alliance “ROBEX”. GEOMAR has recently developed a lander-based deep-sea crawler that operates autonomously based on the original iSeaMC crawler system using the Kraken Autonomy. Combined with the Spanish image processing and modelling expertise in the SME Deusto Sistemas SA the consortium hosts the capacity to establishing a complete semi-autonomous real-time monitoring system. Merging of existing technologies into one operational autonomous product through the unique competence of partners’ support international ambitions (e.g. Blue Growth, GES, Horizon 2020), and renew monitoring that assess impact of human use of the marine environment. The consortium has been invited to contribute to technology/science programs for the Yellow Sea and for European mining and offshore decommissioning industries, which demonstrates the leading role of our consortium. The project is funded through the EU Martera program and started in June this year.

Jan 1, 2018

By Georgy Cherkashov, Tamara Stepanova, Anna Firstova

INTRODUCTION High tellurium contents in the ancient volcanogenic massive sulfides (VMS) and modern seafloor massive sulfides (SMS) have been reported by V.Maslennikov (Maslennikov et al., 2013). However findings of tellurium minerals in SMS are rather rare. The only reported coloradoite and bi-melonite, have been found in massive sulfides from Rainbow hydrothermal field (Fouquet, 2010). Here we present data about Te - minerals in sulfide chimneys of different ages (up to 84.7 kyr - Cherkashov et al., 2010 ) from Semyenov-2 hydrothermal field. The obtained results The Semyenov hydrothermal cluster was discovered and studied in the course of cruises 30 and 32 of R/V Professor Logachev (2007 and 2009) at 13º31´ N, MAR. This area is associated with an oceanic core complex and associated with serpentinized gabbro- peridotites and basalts. Plagiogranites and tonalites have been dredged on seafloor in the Semyenov cluster area (Cherkashov et al., 2013; Pertsev et al., 2012). In total, 25 sulfides samples have been studied. The major and minor mineralogical phases were identified using reflected light microscope. Major element compositions of ore- forming minerals were analyzed on a Hitachi S3400N scanning electron microscope at the Geomodel Center, St. Petersburg State University (St. Petersburg, Russia) with an AzTec Energy 350 (EDX) detector and an INCA 500 (WDX) detector.

Jan 1, 2018

By Matthew Kowalczyk, Steve Bloomer, Peter Kowalczyk

"Mineral deposits found near seafloor hydrothermal venting are of great economic interest. Valuable metals such as gold, copper, zinc, and other polymetallic sulfides are found in appreciable grades in seafloor massive sulfide (SMS) deposits associated with these vents. For mapping these deposits, electromagnetic prospecting is one geophysical method that is very useful because copper/gold rich deposits are highly conductive.Ocean Floor Geophysics (OFG) in 2008 developed the first EM system to successfully map the limits of conductive mineralization in a survey at the Solwara 1 deposit (Kowalczyk, 2008). Since then, towed coincident loop time domain systems have been developed by Waseda University (Nakayama and Saito, 2016) and have successfully detected known mineralization buried at 30m depth. Using a deep tow controlled source electromagnetic (CSEM) array, very clear anomalies have been measured (Murton, 2017) over known mineralization at the TAG field on the mid-Atlantic ridge.In 2014 and 2015, OFG partnered with Fukada Salvage and Marine Co. Ltd. and the Scripps Institution of Oceanography to map methane hydrate deposits off the coast of Japan using a towed controlled source electromagnetic (CSEM) system developed by Scripps. These hydrate deposits are resistive targets, and the Scripps system successfully mapped subsurface electrical resistivity distributions to depths of several 100 metres below the seafloor. OFG is attempting to extend the Scripps CSEM technology to map subsurface conductive SMS deposits to a similar range of depths below the seafloor."

Jan 1, 2017

By Tobias Hens, Andrew Frierdich, Barbara Etschmann, Joël Brugger, Barrie Bolton

"Ferromanganese (Fe-Mn) nodules and crusts are prime targets for future deep-sea mining ventures due to their unusual enrichment of critical metals, such as Ni, Co, Cu, Ti, Te, Zr, Hf, Nb, Y, and REE. These metals are used in an ever increasing variety of high- and green-tech applications such as alloys, batteries for hybrid cars, fiber-optic cables, or liquid-crystal displays.1 Recovery and processing of these deposits will most likely be cost-intensive and require new solutions.2 Thus, innovative approaches towards the development of sustainable metallurgical processes represent one component that can positively affect the marine mining value chain. Dynamic mineral recrystallization of Fe- Mn oxide phases is a geochemical process that may have notable potential for future hydrometallurgical applications.Our research focuses on Mn oxides – potent trace metal scavengers with high sorptive capacity3 – and biogeochemical mechanisms that control Fe-Mn nodule and crust formation, alteration, and trace element enrichment. Biogeochemical redox cycling of Mn is characterized by microbial oxidation of aqueous Mn(II) to Mn(III,IV) oxides and (a)biotic reduction of these oxides to Mn(II)aq. During this cycling dissolved Mn(II) is in direct contact with solid-phase Mn(III,IV) oxides and can back-react via abiotic pathways (e.g., 4 and references therein). This results in continuous dynamic recrystallization of the Mn mineral substrate through coupled dissolution (trace metal release) – reprecipitation (trace metal incorporation) processes.4 We recently demonstrated in new experiments, that Ni is cycled during manganite recrystallization. It has been shown that, although Ni readily undergoes mineral-fluid repartitioning in the absence of Mn(II)aq, dissolved Mn(II) significantly catalyzes Ni exchange between solid phase and solution. Over a period of 50 days about 30 percent of the Ni atoms in Ni-substituted manganite (natural abundance composition) were exchanged with a 62Ni(II)aq isotope tracer at pH 7.5. Based on these outcomes we employed similar techniques to investigate the impact of dynamic recrystallization on Mn oxide phases in deep-sea ferromanganese nodules and crusts from three circum-Australian locations (South Tasman Rise, Lord Howe Rise, Coral Sea) and the Central Pacific Basin."

Jan 1, 2017

By Samantha Smith

Nautilus Minerals (Nautilus) is following the lead of the petroleum industry as it strives to tap vast offshore resources. Planning is well underway for the Solwara 1 Project in the Bismarck Sea, Papua New Guinea (PNG) to recover high-grade seafloor massive sulphide deposits in 1600 m water depth. The deposit contains an average copper grade >10 times higher than a typical land-based porphyry copper mine. The high grades combined with a relatively small amount of overburden ensure the Solwara 1 Project will have a significantly smaller physical footprint than its land-based counterparts. Offshore minerals production also has the advantage of minimal social disturbance. Nautilus is dedicated to setting a high environmental and social responsibility standard. Nautilus recognises the importance of transparent and inclusive stakeholder engagement and has taken a proactive approach to involve as many key stakeholders as possible. One of the first steps in the permitting process in PNG is the preparation of the Environmental Inception Report, which describes the project, its envisaged impacts and the proposed studies for the Environmental Impact Assessment (EIA). Local (PNG-based) and international environmental scientists, anthropologists, NGOs and other experts were involved in the definition of studies conducted for the Solwara 1 EIA and a team of world-leading experts was involved with carrying out the studies, culminating in the preparation of the Environmental Impact Statement (EIS). To ensure transparency, collaborating researchers are free to publish their findings. Following its submission, the EIS was made available for public review and public hearings were held at several locations. The EIS has also undergone a rigorous independent review by PNG government-engaged consultants. Outside the permitting process, Nautilus works alongside government officials to carry out ongoing community consultations. Information dissemination and feedback acquisition has also occurred through the Nautilus website and attendance at a number of international conferences, workshops, and meetings. This paper will outline the leading edge approach Nautilus has taken in completing the environmental impact statement for the world?s first deep seafloor copper-gold mine. In addition, this paper will review the permitting process and the government and stakeholder engagement undertaken as part of Nautilus? desire to ?do it right? in this exciting new industry.

Jan 1, 2010

By James R. Hein

A new data set of cobalt-rich ferromanganese (Fe-Mn) crust chemistry has been completed for the first detailed sampling of a latitudinal crossing of the Pacific equatorial zone of high biological productivity. Samples were collected in January-March, 1999, during the AVON 2 cruise aboard the R.V. Melville, Scripps Institute of Oceanography. Samples were collected from 4.6° N to 9.2° S latitudes along two ridges, the Marshall Islands-Gilbert Islands ridge (4.6° N to 3.5° S) and the Howland Island-Tokelau Islands ridge (1° N to 9.2° S). The two ridges are offset east-west in the region of overlapping latitudinal sampling by about 466 km. We determined the concentrations of 48 elements for 147 samples from 39 dredge hauls taken on 33 seamounts and island flanks that occur between the Marshall Islands to the northwest and Samoa to the southeast. Element concentrations can be examined as varying spatially and with water depth in the ocean and we examine those relationships based on statistical analysis of the chemical and spatial data. The mean Fe/Mn ratio of 1 and mean Co content of 4645 ppm are typical of West Pacific hydrogenetic crusts; but the mean Co content is low compared to those of some equatorial North Pacific sites, such as the Marshall Islands and Johnston Island EEZs. In contrast, the mean Cu concentration (1540 ppm) is 35% higher than the mean concentration for Pacific Ocean Fe-Mn crusts (998 ppm). Another striking difference is the 40% higher Ba concentrations (mean 3107 ppm) compared to typical Central and West Pacific crusts (mean 1876 ppm); but Ba concentrations are lower than those in California continental-margin Fe-Mn crusts (mean 4085 ppm). A final significant difference in Fe-Mn crust chemistry is Zr concentrations, mean 921 ppm (maximum 1523 ppm), which is about 30% higher in this data set compared to the previously determined mean value of 613 ppm for Central and West Pacific crusts. Zirconium has a strong positive correlation with Ba and a weak positive correlation with Mn.

Jan 1, 2003

By Michael J. Cruickshank

The State of Hawaii has expressed concern over deterioration of the tourist beaches at Waikiki, which are becoming seriously depleted of sand. In this report the options for acquisition, transportation and placement .of sand on the beach are examined with respect to feasibility and cost. Ten sources of sand were compared, including commercial, from Australia, Maui, and Barbers Point (3), deposits offshore of the Reef Runway (3), offshore of Waikiki (3), and offshore of Molokai from the Penguin Bank (1).

Jan 1, 1991

By Patrick J. C. Ryall

Remotely control led drills capable of being lowered to the sea-floor from ordinary research vessels have been developed over the past two decades. These drills are currently being used in geological survey programmes on the continental shelves (Canada, Japan, Norway, United Kingdom) and for studies of mid-ocean ridges. Generally the drills fall into two categories: 1) those which are powered from the surface and controlled by an operator, and 2) those which are battery powered and follow an automatic programme. Some drills have a television camera mounted on them sending a picture to the surface as an aid to site selection and geological interpretation. Typically the drills are capable of drilling a core 2.5 - 5 cm diameter up to 10 m long. While most of these drills are designed for <1000 m depth, some can drill in water depths of as much as 3500 m.

Jan 1, 1985