Search Documents

By Jeffrey A. Schaefer

The Olmsted Locks and Dam project is located on the Ohio River approximately 16.5 miles upstream of its confluence with the Mississippi River. It consists of twin 1200 ft. locks with floating and fixed approach walls, five 110 ft. wide tainter gate bays, a 1400 ft. wide navigable pass boat operated wicket gate section, and a 400-ft. section of fixed weir (Fig. 1). The project will have a total cost over 1.0 billion dollars, and as such is one of the largest civil works project underway in the Corps of Engineers.

Jan 1, 2001

By David E. Thompson

This paper describes the full-scale field load testing of three deep foundation units using the Osterberg Load Cell. The load tests were completed on three separate projects, two in Massachusetts and one in New York. The Massachusetts projects involved the load testing of two 18-inch O.D. concrete-filled steel pipe piles over water for railroad bridge reconstruction projects in Revere and Saugus/Lynn. The New York project involved the load testing of a 24-inch diameter drilled shaft socketed into sandstone on land for a building foundation in Rochester. The 18-inch O.D. piles were loaded to failure at jack pressures of 142 to 215 tons. The drilled shaft was loaded to failure at jack pressures of approximately 450 tons. The loading testing procedure is described and the results of the three tests are presented. The advantages and disadvantages of the Osterberg load cell for load testing of deep foundations are discussed.

Jan 1, 1989

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"ABSTRACTTheoretical approach to estimate the ultimate pile capacity gives a rough idea at the initial stage of design that later on strengthen by the execution of static pile load test at site. The static pile load test is the only best option for the estimation of ultimate capacity of various types of piles. There are various methods based on strength, serviceability, net deflection for end bearing, shaft adhesion, graphical and extrapolation approaches for the interpretation of pile load test data to calculate the ultimate capacity. In this paper an attempt is made to evaluate the best-fit method for the estimation of ultimate capacity of single helix screw pile. The pile load tests on model scale were performed on screw piles of different helix diameter. The purpose of adopting model scale of testing was to achieve a state at which settlement increases without further increase in vertical load. The ground was compacted with dry sand at denser state. It was observed from the test results that extrapolation methods such as Chin- Kondner and Decourt predict the load settlement curve of screw piles very well, however ultimate pile capacity was on higher side which may not be suitable for the strength of helix plate. Decourt approach to plot the pile load data showed clear indication of the deformation of helix due to strong subsurface condition. A modified approach in Decourt method is proposed for estimating the ultimate capacity of screw pile having deformed helix whereas reduction factor is suggested for Chin-Kondner method for the estimation of ultimate capacity of intact screw pile.INTRODUCTIONDeep foundations are used to avoid the soft ground at shallow depth that is not suitable for carrying the structural load. Different types of piles have been used to transfer the load to deeper stratum. The screw pile is one of the new piling method and its use is considerably increasing. It consists of a cylindrical steel shaft with one or more helices at various length of the shaft. The diameter of helices (Dw) is usually 2 – 2.5 times the shaft diameter (Ds). The pile is installed to the required depth through torque and pressure. The advantage of screw pile over other piling system is its quick installation mechanism, high end-bearing and uplift resistance, noise reduction and minimum use of man power."

Jan 1, 2014

By Jan A. Nilsen

This paper describes a key element in the construction of a major project undertaken by Harbourfront Corporation in its efforts to rejuvenate the central Toronto waterfront. The Spadina Pier forms one of the two major structures of the $10 million marina complex. Completed in early 1986, the 150 metre(490 ft.) long by 43 metre(140 ft.) wide pier structure will contain a 320 car parking garage as well as providing the foundation of a 17-story residential tower and a two-story retail/commercial complex. However, the pier structure posed a considerable challenge to its developers due to the the many restrictions imposed on the site by the environmental authorities which ruled out the construction of dykes or the placing of other fill materials on the highly contaminated bottom sediments. In addition, access at the site was restricted by its proximity to the main harbour navigation channel and a grain elevator berth. The original design called for a cofferdam to form an integral part of the finished structure. However, the contractor chose to regard the cofferdam as a temporary structure and proposed to construct the pier in the dry by enclosing the 10,000 square metre(107,600 sf) site with a 450 metre(1480 ft.) long single wall steel sheet pile cofferdom 7.5 metres(25 ft.) from the final pier structure. This paper will describes the design and construction of the cofferdam. Prior to finalizing the pier design, a geotechnical investigation of the shale bedrock was undertaken as well as a small sheet pile test cell program to evaluate the feasibility of driving a Canadian manufactured cold-rolled sheet pile into the bedrock. Relying on the design parameters for the shale bedrock, Foundation designed the cofferdam utilizing a post-tensioned bipod bracing system to resist a 7 metre(23 ft.) hydrostatic head as well as the maximum wind and wave forces expected at the site. The bipod bracing system consists of diagonal H-pile raker piles and verticle pipe piles anchored to bedrock with post-tensioned anchors grouted into bedrock.

Jan 1, 1987

By Emad W. Shublaq

Contractual site plans are implemented for executing pile foundations (5 x 5) at segmental concrete bridge. Project schedule demands have forced the contractor to find out the most economical procedure in achieving the goal. This paper presents a site management technique which is applied by the Contractor. This was found to be fruitful and as much as 60% saving was gained.

Jan 1, 1992

By Donald R. McMahon

This paper presents a unique case history that documents the use of a braced secant pile wall to underpin a heavily loaded footing inside of a manufacturing plant. Construction of a pit for a new manufacturing process directly next to the footing necessitated the underpinning. The footing supports an overhead crane that needed to remain operational throughout construction of the pit and therefore, settlement of the footing could not be tolerated. The base of the footing was about 7.7 feet above the base of the 17-foot deep excavation. The footing bears on a silty clay deposit that grades from a stiff consistency beneath the footing to a soft/medium consistency near the base of the pit excavation. This paper describes the design and construction of the secant pile wall and bracing to control wall deformations, ground movements and settlement of the footing. The footing was monitored for settlement throughout construction of the pit and no measurable movement was observed.

Jan 1, 2006

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity.

Jan 1, 2000

By Scott A. Walker, Frank L. Rollo

"The San Francisco Museum of Modern Art (SFMOMA) in downtown metropolitan San Francisco, California, is supported on a mat foundation. Although the mat foundation of the original museum was designed to accommodate a future expansion, the plans for expansion that developed in 2010 required a larger footprint to accommodate the new space requirements of the museum. The new, larger expansion was designed by lead architect Snohetta. It will be a tall 12-story, steel-framed building occupying an area that was once the eastern part of the existing museum as well as two adjacent and newly acquired parcels.As designed, the expansion includes a 30-foot-deep excavation which is surrounded by adjacent buildings and improvements. Because of variable subsurface conditions at the site, geotechnical challenges included mitigating anticipated differential settlement between the existing and new foundations, preventing overstressing of the existing mat foundation, controlling groundwater to prevent settlement of surrounding improvements, and providing temporary support of adjacent structures during excavation for the new basement.To address several of the geotechnical challenges, soil-cement mixed (SMX) ground improvement was recommended by Treadwell & Rollo. However, during contract negotiations and construction, the specialty contractor proposed using jet grouting as an alternative technique for ground improvement. The jet grouting approach was accepted in principal, but when implemented was only marginally successful. Accordingly, the contractor eventually installed SMX panels using a Cutter Soil Mixing (CSM) machine. Because the CSM machine was a late arrival during construction, the contractor was not able to take advantage of the ground-improvement technique to install many of the shoring elements that we had originally recommended (such as the cut-off shoring wall). In the end, SMX panels were installed as ground-improvement beneath the new mat foundation to (1) reduce the potential for liquefaction in clean sand below the groundwater by providing increased rigidity to the soil, (2) reduce the potential for disturbing a weak underlying marsh deposit during construction, and (3) transfer vertical building loads to a layer of underlying dense sand.This paper also discusses the quality control and quality assurance programs that were implemented to check that the ground-improvement techniques used were thorough and complete and provided the required strength to transfer the new foundation loads to the underlying strata."

Jan 1, 2014

By Stefan Aronsson, K. Rainer Massarsch

"ABSTRACT The geology of Sweden is characterized by the most recent glacial period with deposition of very soft clays and loose sand. Due to these difficult geotechnical conditions, new, innovative foundation and ground improvement methods were developed, which today are used in many other countries. Over centuries, Swedish scientists and engineers have made important contributions to the developments in foundation engineering. An important aspect of the success of Swedish foundation engineering in practice is the spirit of close cooperation between practitioners, engineers, and scientists. This has been achieved by the establishing of commissions, with the aim of finding solution of geotechnical problems. The paper focuses on developments in foundation engineering during the last century and does cover present activities in Sweden.IntroductionSoil mechanics and geotechnical engineering play an important role in Swedish society, as most construction activities require the consideration of foundation conditions. The objective of the paper is to summarize important developments in foundation engineering, primarily during the past century, which have influenced geotechnical engineering also in other countries. These achievements are the result of contributions by scientists, engineers and practitioners, only a few of which can be named. The paper does not claim to cover all aspects of geotechnical engineering, as emphasis is on the solution of foundation engineering problems from an international perspective. Thus, ongoing or recent research and development projects and activities within the geotechnical community are not included, as this would exceed the scope of the paper.Over the centuries, Swedish scientists and engineers contributed to the development of civil and foundation engineering. One important reason is the geology of Sweden, which is characterized by the most recent glacial period, resulting in the deposition of soft clays and loose sands in the coastal areas and dense glacial till in the interior of the country. Geotechnical engineering in Sweden has a long tradition and early contributions by several Swedish engineers and scientists have had a profound influence on the current foundation design in and beyond Sweden. A description of early Swedish geotechnical engineering has been presented in several publications by Flodin and Broms (1981), Broms and Flodin (1988), Massarsch and Fellenius (2012). The historic development of Swedish geotechnical and foundation engineering can be divided into four periods. During the “Early Era”, engineers were active in different sectors of military, civil, and mining engineering. Next, the “Industrial Era” comprised developments during the industrial revolution, when the transportation infrastructure of the country was modernized and extended. During the third period, possibly the “Golden era” of Swedish geotechnical engineering, which started at the end of the 19th century and lasted the following fifty years, geologists, engineers and scientists helped to establish modern geotechnical engineering. But also during the recent past, the “Modern Era”, several important contributions to geotechnical and foundation engineering which originated in Sweden, are used in many countries today."

Jan 1, 2014

Jan 1, 1990

This paper summarizes seven years of Italian ex­perience with the use of large calibration chambers for the calibration, under closely controlled stress and strain conditions, of some in situ testing devices which are used in sand deposits. At the present time two calibration chambers are operating in Italy, one at E.N.E.L.-C.R.I.S. (Milan) (*) and the other at I.S.M.E.S. (Berga­mo) (**). Both chambers can accomodate cylindrical samples 1.2 m in diameter and 1.5 m in height. A detailed description of these chambers can be found in Bellotti, et. al (1982).

Jan 1, 1987

By Andrew Moran

In 2021, the University of Pittsburgh began construction of a new recreation and wellness center for students and faculty in the heart of its main campus in Pittsburgh. The design and plans for the center promote the university's goals to create a unique place for members to stay active and to sustainably develop the area within its urban campus. The new 270,000 sq ft (25,000 sq m) center is being constructed within the footprint of two former campus buildings that were demolished, the O'Hara Parking Plaza and the Learning Research and Development Center (LRDC). The recreation center borders O'Hara Street on its south side, the ramp to receiving for the Western Psychiatric Hospital (WPIC) on the west side, an internal campus service road called University Drive A on the north side and a long thin area that will become a new terraced pathway on the east side. The existing site grade ranges from elevation 965-1,058 ft (294-323 m) within the area of the proposed recre­ation center. The ground surface at the site slopes between O'Hara Street in the south upward to the service road in the north with a grade difference of approx­imately 100 ft (30.5 m). The bottom of the excavation for the new center will be near the lowest elevation of O'Hara Street, requiring support of excavation (SOE) on the north (LRDC and O'Hara walls) and west (WPIC wall) sides. Mascaro Construction Company, the general contractor, engaged Nicholson Construction Company for the first stage of the construction, which included existing building demolition, earthwork and SOE systems. Nicholson designed and constructed the SOE systems along the site's north and west sides as described.

Jun 1, 2024

By J. Nakayama

Down-the-hole hammer is commonly recognized as the most powerful drilling equipment for weathered to fresh rock formation including boulders. However, its drilling diameter is restricted by reasons of difficulty to actualize large diameter drillhead and to ensure discharging means of cuttings. Cuttings are usually removed by flushing i.e. uprising return air after compressed air actuates hammer, but in case of large diameter drilling, as the clearance between drill rod and surrounding wall of hole become fairly large, necessary up-hole air velocity to transport cuttings can not be maintained. In case of marine or underwater drilling or high groundwater table, orthodox down-the-hole hammer is obstructed its operation by water. This single head hammer drill combined large diameter drillhead with reverse circulation of drilling fluid enables large diameter drilling extending to 1.5 m, i.e. actualized large diameter mechanical drillhead incorporated with ensured cuttings removal means enabled this range of drilling. This paper introduces its features and actual applications to large diameter bored pile drilling for varied sorts of rocks in maritime construction projects.

Jan 1, 1996

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By Priyadharshini M. R., Premalatha K

"Abstract With the development in the construction of heavily loaded structures, the necessity of pile foundations has increased. For the transfer of heavy loads, it is mandatory that the piles need to be socketed in the underlying rock strata. The load transfer in bored rock socketed piles is by end resistance or the combination of shaft and end resistance which in turn depends on the length of the rock socket. The determination of socketing length of the pile at present is mostly based on a few factors which affect the pile load transfer mechanism. The effect of all the possible factors involved, need to be studied in proposing guidelines for the design of rock socketing length of the pile. Analyses are carried out using finite element analysis software (PLAXIS 3D Foundation) to understand the influence of the thickness of overlying strata for different socket lengths of piles in weak rock. From the load settlement curves, the influence of the overlying soil on the rock socket length isobserved and an effective rock socket length is proposed.IntroductionThe determination of socketing length of the pile at present is mostly based on a few factors affecting the pile load transfer mechanism, which sometimes give a better design and sometimes an uneconomical design. Too much socketing length results in more construction time and higher costs. Therefore, the effect of all possible factors involved need to be studied in proposing guidelinesfor the design of t h e r o c k socket length of the pile.The factors that affect the termination criteria of the rock socketed pile are the capacity requirement, thickness and properties of the overlying soil, characteristics of the founding strata, drilling tools used, roughness of the rock socket and nature of loading.A comprehensive study was performed to understand all the above mentioned factors in different types of rocks. In this paper discussion is made on the settlement results, specifically the influence of overlying sand of different densities above a weak rock. The influence of stress developed is not discussed, keeping in mind the size of the paper under study."

Jan 1, 2014

By Donald A. Bruce

Various types of contemporary Deep Mixing Method (DMM) techniques have been used in the United States since 1986. Such techniques owe their origins to Japanese and Scandinavian developments, which began almost three decades ago. The growing demands of urban infrastructure development and rehabilitation have created a very active and rapidly expanding market demand in the United States especially since the early 1990s, and there is a clear need for a new and fundamental review of the surprisingly large number of DMM techniques that are being used domestically, or are available in other parts of the world. Following a summary tracing the historical development of DMM, and a generic classification of applications, the paper provides a review of each of the many different proprietary methods, which the authors have identified during preparation of an international survey funded by the Federal Highway Administration (FHWA). Data are also provided on commercial aspects of the various DMM techniques worldwide.

Jan 1, 1998

By Franklin M. Grynkewicz

As part of the Boston Harbor clean up project, the new 1,000 mgd Deer Island Sewerage treatment plant includes ten 240 feet high egg-shaped "residuals" tanks. Contract documents called for these structures to be supported on 2,600 sixteen inch concrete filled pipe piles. The project site is underlain by highly variable glacial and marine deposits. Subsurface conditions vary from one extreme where firm glacial deposits exist at subgrade to the other extreme where 70 feet of medium stiff clays overlying weathered bedrock must be dealt with. The most common profile consisted of 15-20 feet of sands, 20-40 feet of marine clays, and 20-60 feet of stratified glacial deposits (commonly called tills) overlying Argillitic bedrock. Post bid redesign work, initiated as a cooperative effort between the owner and the general contractor, demonstrated that an $8 million savings could be realized if high capacity 48 inch diameter caissons replaced the specified pipe piles. A highly unusual arrangement of having the general contractor and specialty subcontractor providing input to the owner's engineering team allowed the redesign work to proceed on a "fast-track" schedule.

Jan 1, 1992

By Amr Sallam, David Thompson, Moataz Hassan

"The Little Lake Harris (LLH) Bridge was constructed in 1951 to replace the eastwest County Road 48 Bridge connecting the towns of Howey-in-the-Hills and Astatula in Lake County, Florida, United States. The 78-span bridge carries two lanes of traffic, is 3,130 feet long, and 36.1 feet wide. The concrete deck is supported by steel I-girders carried by one row of 18-inch square precast concrete driven pile. In the late 1980's, slight settlements were observed in several bents. In 1990, Florida Department of Transportation (FDOT) initiated annual survey of deck elevations during bridge inspections to monitor settlement. Due to the slow nature and magnitude of settlement, substructure instability was not a major concern to the department. However, public concern over the settlement and rough ride of the bridge continued to rise. FDOT contracted Kisinger Campo & Associates Corp. (KCA) to provide the needed design to correct the dips in the riding surface and minimize future settlement. KCA's initial design was based on the concept of ""helper bents"" at the settled bents in order to restore the bridge to original elevation. Estimated construction cost for seven helper bents was about $3.3M. FDOT requested evaluating other alternatives to reduce the cost of the bridge restoration. KCA involved the geotechnical consultant, Terracon Consultants, Inc. (Terracon), to perform a peer review and provide an economical alternative solution. Jacking and shimming the bridge was determined to be both technically viable and economical with a total cost of less than $300K. The design was completed in March 2010 and construction was completed in February 2011. This paper provides an overview of the LLH Bridge history, summarizes the evolution of the design methodology including the findings of the geotechnical study and presents lessons learned during the design and construction of the project.INTRODUCTIONThe Safety and Preservation of the State Highway System is the top priority of the FDOT. Therefore, FDOT initiated a bridge management program that starts with conducting biennial safety inspections performed by Certified Bridge Inspectors (CBI). The inspection reports together with the CBI’s recommendations are reviewed by a registered Professional Engineer (PE) and work orders are issued with priority ranking depending on the severity of the bridge deficiencies. If the scope of work is considered beyond the in-house crews’ capability, the work is then included in a contract for and bid. LLH Bridge was a little different. It was initiated in direct response to number of complaints the FDOT District 5 Structures Maintenance Office (D5SMO) received regarding settlement of the Little Lake Harris Bridge."

Jan 1, 2015

By Jim Henry

I would say mainly the cost. I showed only 3 cases. One of them was the one that Allen just described and there were two other cases. In those cases it was fairly easy to develop a solution using limited mobility grout to treat the soft soils suitable for the limited bearing pressures required by the structures. LMG readily provided a fairly reliable system for the foundation support at a reasonable cost.

Feb 10, 2003

By Larry Rayburn

Design of cost effective engineered solutions to complex problems requires the team efforts of the owner, the designer and the specialty construction contractor. The basic ingredients of success required to remain competitive and still produce a quality product are creative design based on experience and sound engineering principles, plus practical aspects of constructibility. The three case histories describe creative design/construct approaches that benefited all parties. 1. Introduction The increasing demand placed on specialty contractors to provide cost effective buildable solutions to complex construction problems compels us in the industry to be highly innovative. The practice of geotechnical engineering is considered more of an "art" than perhaps the other disciplines within civil engineering largely because of the basic nature and variability of soil and rock. The geotechnical design engineer must have the knowledge of the components of his design and know the limitations of his equipment and labor force. Thus, for the design/build specialty contractor the potential for creation of unusual solutions to difficult problems is quite high.

Jan 1, 1991