Search Documents

By Harpal Parmar

This paper evaluates dynamic methods of pile capacity prediction by comparing their results to static load test results. Dynamic and static pile load test data were assembled from four southeastern states of the U.S. End-of-drive and restrike capacities were evaluated using the Pile Driving Analyzer (PDA) and by wave equation (WEAP) analyses. These were compared to static (Davisson criterion) loads. The best comparison was obtained for restrike PDA results; restrike wave equation analyses values also compared well. The end-of-drive results for both methods-showed relatively poor comparisons. The PDA was recognized as an important tool to measure energy transferred to the pile; this transferred energy was recognized as an uncertainty when conducting wave equation analyses. A statistical analysis showed restrike capacity results to be associated with higher precision and accuracy as compared to end-of-drive methods. The authors believe that restrike dynamic testing is essential to establish long term static soil strength and that it will lead to accurate and cost-effective design of piles.

Jan 1, 1996

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

By Kouichi Tomisawa

Two bridges were constructed for extension work of Central Hokkaido Connection Road in 2005 at two different sites. Pile group foundations were employed for the foundations of abutments of the two bridges. In order to assess the performance of the constructed piles in the sites and to obtain design parameters for design in future, static alternating cyclic horizontal load test was carried out on one of the open-ended steel pipe piles constructed at each site. The ground at one site was characterised as a thick deposit of volcanic soils, and the ground at the other site was characterised as a very soft peat layer near the surface. In this paper the results of static alternating cyclic horizontal load tests on the piles at the two sites are presented and discussed in detail.

Jan 1, 2006

By Carl-John Grävare

This paper deals with some of the systems and equipment that are being developed and/or are in use in Scandinavia. The main subject is the development of loading tests on the piles using monitoring equipment. This paper also describes ground improvement using lime-cement columns, expander body piles and steel core piles.

Jan 1, 2000

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By Masaki Kitazume

"Abstract The wet type and dry type of deep mixing methods have been developed and widely applied for on-land and marine constructions in Japan. The quality assurance (QA) of the methods has been usually carried out by unconfined compression test on field stabilized soil sampled by core boring in Japan. In some other countries, stabilized soil excavated by the wet grab sampling instead of core sampling is often subjected to unconfined compression test for quality assurance. There are several merits and demerits in each method, but few studies have been carried out to compare the stabilized soil strength of these two types of specimens to discuss their applicability to practical construction. The author has conducted a series of field and laboratory tests to compare the stabilized soil strength and discuss the applicability of wet grab sampling to QA for wet and dry types of deep mixing method.In this study, the wet grab sampling was carried out at two road embankment construction sites where the wet type and dry type of deep mixing were applied. The cement stabilized soil was excavated at the three depths by a wet grab sampler soon after the DM column construction. The test result is compared with the other test data in the previous study to discuss the applicability of the web grab sampling method for QA of cement stabilized soil.IntroductionThe Deep Mixing Method (DMM), an in-situ soil stabilization technique using cement and/or lime as a binder, is often employed to improve soft soils (Kitazume and Terashi, 2013). A variety of factors and their interactions affect the eventual strength of a deep-mixed column, while some of which are controllable (e.g. binder type and dose) by engineers while the others are not (e.g. soil types, ground temperature, etc.; Babasaki et al., 1997). In addition to laboratory mix tests, which in essence are a parametric study to estimate the influence of these factors on a particular soil’s strength, the quality assurance (QA) practice in Japan usually involves unconfined compression test on sampling cores from the stabilized columns after a given curing period. It has been recognized, however, that the ‘field strength’, or the strength of the retrieved core, quf is on average lower than the ‘laboratory strength’, qul, evaluated by laboratory mix test. Also allowing for the inevitable variability, existing guidelines (for example, PWRC, 2004 and CDIT, 2008) recommend the design quf /qul values of, for example, 0.5-1.0 for the CDM (Cement Deep Mixing; a wet-type technique, in which binder is added as slurry) and 0.2-0.33 for the DJM (Dry Jet Mixing; a dry-type technique, in which binder is added as powder)."

Jan 1, 2014

By Jamie D. McEwan

To cater for the future introduction of 12 car trains, London Blackfriars railway station is being extended from the north end to span across the River Thames. Following the demolition of existing buildings, a number of challenges had to be overcome including working adjacent to a live railway line, above live London Underground tracks and working in small restricted spaces. Trains entering and exiting two lines of track at the bridge's north end of track meant that access was difficult due to the location and proximity to existing infrastructure. The site was very much constrained and congested and there were also a series of works in place to maintain passenger flows so as not to inconvenience the travelling public. The site had been developed many times in the past resulting in a number of obstructions that would require removal during the piling work including old brickwork, reinforced concrete, redundant railway sleepers and track and existing concrete and timber piles. A number of solutions had to be devised to overcome these obstructions. Piling works were undertaken during the day and at night to meet programme.

Jan 1, 2011

By J. P. Welsh

Ground Modification construction is rapidly evolving in the United States. An assessment of the construction status of Ground Modification methods with their dates of introduction and general acceptance in the United States is summarized. Seven of these techniques are discussed in depth with short case histories; namely, Dynamic Deep Compaction, vibro-compaction, vibro-Replacement, chemical grouting, compaction grouting, slurry grouting and jet grouting. Additional case histories are presented to illustrate the trend of combining Ground Modification techniques to solve specific site problems.

Jan 1, 2010

By F. Z. Suo

Baoahan Iron and Steel Complex is situated at lower beaches of the Yangtze River. The subsoils 50~70 M below the surface is a deposite of Yangtze River delta, consisting mainly of weak silty clay and loam, with low soil bearing capacity. Consequently, to build on such a weak soil a grant iron and steel integrated works weak soil improvement at the Complex, pile foundation is the effective type. It is estimated that at the first stage of Baoshan project 60,000 piles have been driven, of which 60% are steel pipe piles and 40% reinforced concrete piles. To provide reliable basis for pile foundation design, on-site loading tests were carried out for long reinforced concrete piles 27,45 60 M in length ,with strain gauges on the chief reinforcement of pile shaft and strain rod on pile tip. Based on loading tests, the paper discusses and analyses some issues, including determination of load transfer mechanism distribution of frictional resistance. Tests show that as far as long friction piles in soft clay are concerned, regardless of the properties of pile tip's bearing stratum, loads are mainly carried by shaft frictional resistance which it is effective to determine pile capacity in terms of P ~ S relationship.

Jan 1, 2010

By Jiwei Duan

The energy transferred from a hammer to the pile top is considered as the effective energy in this paper. The effective energy is related to the pile dimensions, soil and pile-soil interface properties. This relation may be expressed as an equation based on the dimensionless theory. The relationship between pile capacity and effective energy was studied by performing a series of wave equation analyses using a commercial software called GRLWEAP (Wave Equation Analysis Program) by GRL Engineers, Inc. The results show that the pile capacity increases with the blow count when the effective energy is constant, however, it has a little change as the blow count is over 100 blows per foot. The pile capacity decreases as the ratio of pile penetration depth to pile diameter increases if the effective energy is constant. The pile capacity will increase as the pile diameter and wall thickness increases if the effective energy is constant. The pile stickout (pile length above the ground surface) does not have a significant effect on the effective energy and may be neglected. Curves for pile capacity versus effective energy are presented to be used for preliminary hammer selection according to effective energy and hammer efficiency. Finally, a case from PDA testing was studied. Measurements of the effective energy and pile capacity by CAPWAP were presented and compared with the results by GRLWEAP.

Jan 1, 2006

By L. F. Albert

The paper describes solutions given to foundation problems during the reconstruction of a power plant set on fire, located adjacent to several still Working Units. After a detailed site and laboratory investigation, it was decided that it could be possible to include within the new foundations the preexisting cast in situ driven piles with enlarged base 50 cm in diameter and let them work with new 41 cm driven, cast in situ piles without enlarged base. Demolition of existing caps was carried out with expansive mortar in order to avoid any possible damage to piles, whose actual conditions were checked by several load tests. New piles were designed to support service load by shaft resistance, in order to limit total and differential settlement. When piles had to be driven adjacent to nearby structures, measurements of peak soil particles velocity were carried out while driving piles at decreasing distance from critical locations. By preboring most of the upper clay layer it was possible to reduce within safe limits for structures the induced vibrations.

Jan 1, 1989

By W. J. Kingwell

My comments and questions are addressed to Mr. Troughton. It seems to me that the tests were very well tailored to determine long term effects on performance of bearing piles as groundwater pressures rise in the London Basin. This rise is being simulated by means of a groundwater recharge system but it would be informative to have further details of the controls of conditions simulated. Ideally the porewater pressure in Standpipes 1, 2 and 3 should be the same throughout the test. Under test conditions are there not practical dif­ficulties? Recharge Well C2 is a lesser dis­tance from the pile than the other wells. Was the rate of recharge to C2 regulated to a lesser rate than the other three? In my experience the rate of acceptance usually varies from well to well. Under a common feed pressure were mea­sures taken to compensate for this? Since the problem does not only affect London, but also Liverpool, Nottingham, Birmingham and to a lesser extent, Manchester, I question whether an ideal procedure is being used. It is well known that rates of acceptance decrease with time and often recharge wells need to be flushed out at regular intervals. Other pro­cedures may need to be adopted to accurately simulate the effect of groundwater rise, if tests of longer duration are to be considered.

Jan 1, 1991

By Aly M. Mohammad

The Delaware River Tramway will link civic and retail developments in Philadelphia, Pennsylvania and Camden, New Jersey. Twin 300-foot towers will anchor the cables at either side of the river. Four high capacity drilled shafts designed by the Geotechnical Department of DMJM+HARRIS support each of the towers. At the Philadelphia tower, each 6-foot diameter shaft extends 130 feet deep and terminates with a 30-foot rock socket. The shafts are situated within the footprint of an existing relieving platform, which complicates the typical construction sequence. Also, the subsurface conditions at the site provide a unique challenge in both the design and construction of the drilled shafts. During the construction of the four-drilled shafts for the Philadelphia tower, a 6000-ton Osterberg load test was performed on the first shaft to verify design assumption and confirm the shaft capacity. The results of the test were utilized to establish load transfer characteristics and develop foundation design parameters suitable for the site conditions. By doing so the Design Engineer was able to reduce the length of the rock sockets on the remaining production shafts by approximately 5 feet per shaft. As a result, the test provided a significant cost saving to the Owner by eliminating 15 feet of rock drilling from the construction costs. This paper presents a description of the unique design and construction methods adopted for the foundations, also on the Osterberg load test including equipment used, number and locations of strain gages, and interpretation of results. The results and findings presented in this paper could benefit both the design and construction industries because it provides a comparison between geotechnical design assumption and actual field measurements; which has always been a challenge particularly for rock formation.

Jan 1, 2002

By C. Van der Veen

The use of the quasi static (Dutch) Cone Penetration Test (CPT) is described as a tool to predetermine the ultimate bearing capacity of the pile point. An analysis is given why a purely theoritical approach does not meet with success. A practical method is explained of extrapolating the cone resistance to predict the pile point resistance. The method has been calibrated against the result of 32 selected high standard loading tests on pile points in the Netherlands.

Jan 1, 1989

By A. V. Shroff

The Indian Standards code of practice for design and construction of underreamed piles contains provision for installing such piles in expasive soils. In recent years, a large amount of research work has been carried out in the analysis, design, construction and performance of underreamed piles in expansive soils. This paper suggests that the results of this research field tests should be included in the code. Various additions and modifications as well as deletions that should be incorporated in the code are discussed.

Jan 1, 1996

By Niels Krebs Ovesen

Close economic cooperation was established among the countries in western Europe during the seventies. As a consequence, among others, a need for harmonized technical specifications for civil engineering works arose. Technical specifications for design and execution of building and civil engineering structures exist in most of the European countries. In some countries such technical specifications are part of the building regulations and in other they are independent codes of practice and standards. The works on the Eurocodes was initiated by the Commission of the European Communities about 1976. The Eurocodes are intended as common unified design codes for different load bearing structures constructed from different materials. They are also intended to cover design of geotechnical structures. They are established with a view to promote the free movement of goods and services within the member states of the European Community - the so called Internal Market - and within the member countries of the European Free Trade Association, EFTA by removing obstacles arising from different rules for calculation and design.

Jan 1, 1994

By Michael Lane

With the success of their existing casino operation on the Ohio River in Lawrenceburg, Indiana, the Indiana Gaming Co., LP planned a major expansion of the current facilities. This expansion includes a second 1400+/- car parking garage, a new surface parking lot, elevated walkways, and a new floating casino that will double their present square footage and consolidate all of the gaming activity to one floor. In March of 2006 Richard Goettle, Inc. was awarded the general contract to construct a 260? x 520? boat slip for the new Argosy VII floating casino. An Open Cell® bulkhead system was specified as the means for constructing the new slip. Our contract included the purchase and installation of 300,000 square feet of PS27.5 sheet pile, excavation of 230,000 cubic yards of soil, and a 3300 square foot Mechanically Stabilized Earth wall.

Jan 1, 2008

After the Loma Prieta Earthquake, which caused major damage to viaducts in the Bay Area, the California Department of Transportation set up a test programme for foundation piles. Funderingstechnieken Verstraeten B.V., beter known as Fundex, was approached, since one of the piling systems of Fundex, named Tubex, is extremely suitable in areas sensitive to earthquakes and we were very much interested to prove the capabilities of this piling system. Equipment For the installation of Tubex and Tubex grout-injection piles special piling equipment is required. Since our company is not only a contractor, but also a designer and manufacturer of piling equipment, all special equipment for our range of foundation techniques is designed and built by our own piling equipment department. For the installation of both Tubex piles and Tubex grout-injection piles for the Caltrans test programme, the following pieces of equipment were selected: a) Fundex F12 piling rig b) Drill table c) Hydraulic powerpack d) Grout mixing unit and high pressure pump

Jan 1, 1993

By Frank Haehnig, Kjell-Åke Averstad, Johannes Glückert

"AbstractThe Söderströmstunneln is part of the Citybanan project that is currently under construction in the centre of Stockholm. Main part of the lot Söderströmstunneln is a 300m long immersed tunnel connecting the inner-city islands Södermalm and Riddarholmen. It consists of three tunnel elements that have been immersed in summer 2013. Since the solid bedrock is descending in that area to more then 40m depth, the tunnel elements have been placed and are permanently supported on four pile groups that have been constructed in advance. The common Swedish system of steel core piles has been used to built the pile groups. Drilling and installation of the steel cores piles in free water depth of up to 20m had to be done from a pontoon. The steel core piles are connected with underwater concrete pile caps.IntroductionCitybanan is a new 6km long double track railway tunnel running beneath central Stockholm including two new underground stations Odenplan and Stockholm City. When completed in 2017 commuter trains will have their own tracks through Stockholm, whereas the remaining railway traffic will continue to use the exisiting two tracks (see Fig. 1). This will double the capacity of the railway traffic through Stockholm. The Swedish transport administration Trafikverket is the client for this project. The design and built contract is carried out by the German contractor Züblin Spezialtiefbau GmbH together with their Swedish subsidiary Züblin Scandinavia AS.As the new Citybanan tunnel is in large parts situated below the bedrock level, it can be executed as rocktunnel in the common drill and blast method. Between the two inner-city islands Södermalm and Riddarholmen the tunnel is crossing the Söderström, an arm of the lake Mälaren. Here the bedrock is descending to a deep valley with more then 40m depth. To connect the rock tunnels between these islands a 300m long immersed concrete tunnel supported on pile foundations is currently under construction."

Jan 1, 2014

By Darrell L. Beddard

The Loma Prieta earthquake occurred on October 17, 1989 at 5:04 PM, Pacific Daylight Time. It measured 7.1 in magnitude and was felt from Los Angeles north to the Oregon state line and east to western Nevada. The epicenter of the earthquake was located along the San Andreas Fault, in the Southern Santa Cruz Mountains just north of the City of Watsonville, California. It was the largest earthquake to occur in the San Francisco Bay area since the 1906 earthquake. A total of 87 aftershocks of Magnitude 3.0 or larger were recorded within 21 days after the seismic event. As a result of this earthquake thirteen State-owned and five locally-owned bridges were closed to traffic. Three of the most publicized State-owned structures closed to traffic were Struve Slough Bridge, San Francisco-Oakland Bay Bridge and Cypress Street Viaduct. Struve Slough Bridge was twin slab bridges that collapsed and were rebuilt and open to traffic three months after the earthquake. San Francisco-Oakland Bay Bridge experienced collapse of upper and lower spans at Pier 9 and was reopened to traffic one month after the earthquake. The Cypress Street Viaduct experienced collapse of 48 bents that resulted in the upper roadway falling onto the lower roadway.

Jan 1, 1995