Search Documents

By T. M. Siew

"This paper begins with a brief discussion of the geology of the Newfoundland Zinc Mine area. The results of groundwater studies and pumping tests are then presented. It was decided that groundwater in the mine could best be controlled by conventional sump pumping and grouting. The system is fully described, as well as plans for improvements on the method. LocationThe Newfoundland Zinc Mine is located in the Great Northern Peninsula of Newfoundland, six miles northeast of Daniel's Harbour. The mine is situated at an elevation of approximately 350 feet above sea level, 5 miles farther inland , west of the long range of mountains which rise abruptly with elevations of over 2,000 feet above sea level.GeologyThe ore deposits occur in lower Ordovician carbonate rocks that form part of the stable St. Lawrence platform, which is mainly composed of (1) the lower Cambrian Labrador group, (2) the upper Cambrian to lower Ordovician St. George group, (3) the disconformity overlying Middle Ordovician limestones and shales of the Table Head formation and, (4) two overlying klippen composed of Cambrian and lower Ordovician rocks.The ore deposit is a Mississippi Valley type of the Tennessee variety, having proven are reserves of 5.3 million tons averaging 9.70/0 zinc from eleven ore zones which exist in an area of 5.5 square miles.Among these ore zones, the L zone is the major underground mining area, and is by far the largest of the known deposits. It has proven are reserves of 3.4 million tons with 11.5% zinc; this underground development has been inprogress since 1974.Stratigraphically, the orebody, which occurs about 300 feet below the disconformities between the Table Head and St. George formations, is situated in the upper St. George formationof lower Ordovician age.The upper St. George formation of the L zone is divided into three main units (Fig . I) : the underlying lower limestone the middle grey dolomite pseudo breccia unit and the overlying siliceous dolomite unit. In this area of the mine, the beds of the St. George formation dip gently west to northwest to 10 to 15 degrees. The orebody, which is generally strata controlled with a southwesterly plunge and which has the form of thin, narrow, but elongate, en-echelon ore bed s, is contained in grey dolomite pseudo breccia. Its dimensions vary from 50 to 900 feet in width and 8 to 120 feet in thickness, and the over-alllength exceed s 6,000 feet.The surficial deposit of the area is a till comprising a heterogeneous mixture of sand, gravel, cobbles and boulders, with an average depth of 20 feet."

Jan 1, 1980

By D. Asefi

A new method to detect microstructural features such as recovery and recrystallization as well as cold rolling reduction in low carbon steels was developed based on magnetic hysteresis loop measurement. To this aim, a hysteresis loop measuring apparatus, specifically designed and assembled for plate samples was employed. It is shown that maximum field (Hmax) of hysteresis loop, measured at constant maximum flux density (Bmax) of 0.5T, is an adequatemagnetic property to monitor different stages of changing microstructures during annealing.

Oct 1, 2011

By Masayuki Ishikawa

In a radio frequency and optoelectoronic device packaging, Gold-Tin (Au-20 wt% Sn eutectic) solder is used widely due to the excellent electrical and thermal conductivity, high strength, and negligible creep characteristic under repetitive thermal cycling. With the recent lead-free movement, Gold-Tin solder is recognized as an alternative material for high temperature Lead-Tin solder. Generally, Gold-Tin solder is supplied in the forms such as ribbons, pellets, and ring frames. However, these forms must be set-up accurately on the joint area to press chips in bonding, therefore, it is difficult for these forms to satisfy the recent requirements for the down sizing in the connection areas. On the other hand, Au-20 wt% Sn solder paste can be applied flexibly to various supplying methods, such as printing, dispensing system and pin transcript. These methods also make it possible to reduce the production cost. However, in the case of using the solder paste, the void issue is one of the most undesirable problems. The void causes the degradation of the characteristics such as the bond strength, electrical characteristic and thermal conductivity. We have been intensifying the development of the void free paste, and have achieved void reduction by optimizing the powder size, the flux composition and the reflow condition.

Oct 1, 2003

By Norman O. Lotter, Lori Kormos, Greg J. Wilkie, Peter J. Whittaker, Johannes S. Stickling

"Assessment of opportunities to improve mineral processing performance in existing concentrators and in describing undeveloped orebodies is key to improving the business case of a mining company. This assessment has traditionally been performed using the distinct and separate inputs from Mineral Processing and Mineral Science.More recently, Process Mineralogy has been used to integrate these two disciplines. This trend has been driven by the need to develop and process more challenging ore deposits, and has been assisted by the availability of modern automated instruments. Together with the acquisition of a QemSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) from CSIRO in Australia, and with the use of a supporting SEM with EDX / WDX capabilities and an XRD, the development of Process Mineralogy at Falconbridge commenced in 1997.The sampling challenges in presenting a QemSCAN with representative sample material at the polished section level are significant, but have been effectively addressed. The full description of this aspect is beyond the scope of this paper.It is shown that, by use of this approach, the set nature of an orebody can be best exploited with selected flowsheet changes in a concentrator which address the generic characteristics of the orebody. In this way, the flowsheet provides a process that more effectively fits the mineral processing requirements of the ore. This leads to clear and tangible improvements in grade and recovery."

Jan 1, 2002

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012

By Philippe Caudal

This paper presents a case study in which a slope failure was observed on the west wall of the LAB Chrysotile mine in the vicinity of the main ramp in January 2010. Airborne LiDAR results were used to evaluate slope geometry before and after the failure occurred. Back analysis of the failure was performed to assess rock mass properties at the slope scale using various numerical techniques: limit equilibrium, finite elements and fracture networks. The various approaches correlated well with field observations.

Aug 1, 2013

By M. W. Franklin, D. W. Hendriks

"Changing ore types, feed grades and c1rculat1ng loads are some of the many factors that can make flotation feed-back control difficult. To control a flotation circuit using conventional fixed-parameter control algorithms, one must either tune the controllers very often or tune the controllers to the middle of the normal operating range. The former approach is very time consuming, while the latter approach can lead to long periods of either very sluggish responses or highly reactive responses which can lead to instability. The problem becomes compounded if feed-forward variables are introduced, creating even more variables to tune. An alternative to a fixed-parameter control algorithm is an adaptive control algorithm. An adaptive control algorithm continuously retunes itself based on previous reactions to its changes. Feed-forward control also becomes much more viable because the algorithm will tune the feed-forward parameters and the feed-back parameters simultaneously. Using the combination of feed-forward and feed-back tuning is an effective way to decouple the loops needed in flotation circuits where one circuit feeds into another. The advantages of adaptive controllers over conventional controllers will be introduced through the use of a simulator. Also discussed will the be the implementation of adaptive controllers at Brunswick Mining and some of the modifications that are available to help solve more difficult control problems.Brunswick Mining is located just outside of Bathurst, New Brunswick. The concentrator processes approximately 10250 tonnes per day of ore that assays at approximately 8.9 %zn, 3.6 %Pb, 0.3 r.cu and I 00 gram/tonne of Ag. The four products produced are zinc concentrate assaying 51 %Zn, lead concentrate assaying 34 %Pb, copper concentrate assaying 21 %Cu, and a bulk concentrate assaying 32 %Zn and 18 %Pb."

Jan 1, 1986

By A. J. Hynes, Lutes. G. G., Ravenelle. J. -F.

"The Anomaly A area of the Clarence Stream gold deposits in southwestern New Brunswick contains mineralized structures that bear geometrical relationships to regional folding events. The four mineralized zones of Anomaly A (AD, MW, 93, and Murphy) are hosted by turbiditic graywacke, quartzose wacke, siltstone, and argillite sequences of the Kendall Mountain Formation. A regional scale structural analysis reflects at least four deformational events, three of which appear to control the folded geometry of Anomaly A (D2, D3, and D4). F2 and F3 folds are coaxial and are refolded into a dome and basin geometry by F4 folds. The mineralized zones are subparallel to axial surfaces of F2 folds. Structural analysis of a mineralized zone exposed at surface indicates that gold mineralization is hosted by a quartz-vein system that comprises veins generated during both D2 and D3. Threedimensional representations of Anomaly A created using drill-core data and ®GoCAD suggest that the quartz-vein system was emplaced in fault structures during D2 as well as within brecciated dilation zones during D3. Three of the four zones that make up Anomaly A have F2 hinge surfaces that can be linked through a geometry compatible with the style of F3 and F4 folds. The apparent continuity of these three zones indicates the potential for kilometer-scale mineralized structures at Anomaly A. Le secteur de l’Anomalie A du gisement aurifère Clarence Stream contient des zones minéralisées qui montrent des relations géométriques avec les épisodes de déformation régionale. Les quatre zones minéralisées de l’Anomalie A (AD, MW, 93, Murphy) sont comprises dans une séquence turbiditique composée de grauwacke, de wacke quartzitique, de siltstone, et d’argilite appartenant à la Formation de Kendall Mountain. Des quatre épisodes de déformation étudiés par l’entremise de cartographie structurale, trois semblent contrôler la géométrie de l’Anomalie A (D2, D3, et D4). Les plis P2 et P3 sont coaxiaux et sont replissés en dômes et bassins par les plis P4. Les zones minéralisées sont subparallèles aux plans axiaux des plis P2. Une analyse structurale effectuée sur une zone minéralisée exposée à la surface indique que la minéralisation aurifère est localisée dans un système de veines de quartz qui contient des veines générées durant D2 et D3. Des représentations en trois-dimensions créées avec le programme informatique ®GoCAD à partir de données de forages suggèrent que le système de veines est localisé dans des zones de failles D2 ainsi que dans des zones de dilatation associées avec D3. Trois des quatre zones qui forment l’Anomalie A possèdent des plans axiaux P2 qui peuvent être liés par l’entremise d’une géométrie qui respecte le style des plis P3 et P4. La continuité apparente de ces trois zones indique qu’une structure minéralisée pourrait s’étendre sur plusieurs kilomètres dans le secteur de l’Anomalie A."

Jan 1, 2008

By Alan Galley

CMIC Mandate CIM Annual Meeting, Toronto, May 6, 2013 To increase mining research, innovation and commercialization efforts in order to strengthen Canada?s pre-eminent role as a global leader in mineral exploration, mining and knowledge-based services and technologies. To increase the supply of highly qualified graduates from mining and earth sciences faculties to meet the significant demand today and into the future of industry, governments and academia. The CMIC initiative is intended to develop long term research strategies that extend five or greater years. Such a research plan will underpin fundamental research and innovation and the training of HQP

May 1, 2013

By Art Carino

"The McClean Lake operation is located in the Eastern Shore of the Athabasca Basin in northern Saskatchewan some 700-air kilometers north of Saskatoon. It is operated by Cogema Resources Inc., the major share holder of the joint venture consisting of Cogema Resources Inc., Denison Mines Limited and OURD, a consortium of Japanese utilities.The JEB mill is the first uranium mill to be constructed and licensed in North America within the last 15 years. The mill uses conventional uranium unit process but employs innovative techniques unique to the JEB mill.This paper presents brief descriptions of the various unit processes, the innovations and the commissioning strategies developed to achieve the designed production capacity in the shortest possible time.INTRODUCTIONThe McClean Lake ore body was discovered in 1979, followed by the discovery of the JEB ore body in 1982. From 1985 to 1990, a cluster of deposits named Sue A, Sue B and Sue C were discovered. Environmental Impact Assessment (EIS) of the McClean Lake project began in 1990 under a joint federal-provincial process. Following the public hearings in 1993, the governments gave approval to proceed with the construction of the project, subject to fulfilling licensing requirements.The McClean Lake ores are located in the uranium-rich geological region of Saskatchewan known as the Athabasca Basin, 700 air kilometers north of Saskatoon. The JEB mill is located near the mined out JEB open pit that is now used as the tailing depository.The approved mill has a production capacity of 6,000,000 pounds of U3O8 annually and is capable and licensed to process JEB, Sue A, Sue B, Sue C, McClean Lake, and Midwest Lake deposits. Although the EIS has been approved, Mining of the Midwest Lake deposit has not been approved at this time."

Jan 1, 2001

By Fabien Miller

Automation technologies are increasingly envisaged to improve underground mining productivity. However, the technologies need to be used and adopted gradually in order to get the best benefits. This paper presents the technical and operational aspects of autoguided production vehicles at Brunswick Mine. During 2001 Noranda?s Brunswick Mine has successfully commissioned an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two orepasses. Operational advantages include increased system capacity and enhanced safety and comfort for the operator. The data obtained up to now indicate that the system can operate reliably in mine production

May 1, 2002

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

"The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members — the Universities of Queensland and Sydney and the CSIRO1, and by its industry members — BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining. Mechanized Rock ExcavationThe disadvantages of the drill-and-blast excavation method are widely recognized and the last half of the 20th century has seen mining companies and mining research organizations aggressively pursue technology to excavate rock by other means. As discussed below, despite considerable effort and large amounts of funding, the quest for mining’s “Holy Grail” has been unsuccessful in all but the weakest rock types.COMRO (the Chamber of Mines Research Organisation) supported by the South African gold mining industry, spent three decades and (probably) tens of millions of dollars developing prototype drag bits and, later, impact breaking machines aimed at the mechanized stoping of narrow, tabular reefs. This work has not yet produced a commercially-attractive mining system. Work continues in South Africa to mechanize these stoping operations although now the emphasis is on the use of diamond-wire sawing techniques. This work remains in the experimental phase.Both British Coal and Germany’s Bergbau- Forschung spent many years developing techniques trying to extend the range of rock types which roadheaders could cut economically. Again, although new knowledge was produced, it is difficult to claim that any new commercial mining systems emerged from this work."

Jan 1, 2001

By Jose R. Hernandez-Aguilar

"Three models to predict the effect of bubble size (Db) on metallurgical response were tested in a pilot-scale flotation column at Teck Highland Valley Copper mine. The column was fed with slurry collected from the Cu/Mo separation circuit. The first model was the one developed by Gorain et al. (1997), which assumes that the collection zone rate constant (kc) is inversely proportional to Db. The second model was the one proposed by Hernandez-Aguilar et al. (2010), which considers kc as an inverse square function of Db. The third model was the one developed by Yoon and Luttrell (1989) which provides expressions to describe the efficiency of particle collection (E) based on first principles. The results showed a significant bias between experimental and predicted data using the model of Gorain et al. (1997), possibly reflecting the model’s inability to explain the impact of bubble size, bubble rise velocity and flow regime on E. The model of Hernandez-Aguilar et al. (2010) well described the experimental evidence. The model of Yoon and Luttrell gave accurate and unbiased predictions. However, Yoon and Luttrell’s approach calls for a criterion to determine whether the flow regime is potential or intermediate, a subject that requires more fundamental research.INTRODUCTIONParticle collection, i.e., bubble-particle collision followed by attachment, is the basis of flotation. In a quiescent environment (such as the one observed in a column, or away from the impeller in a mechanical cell), a collision event can take place as long as the “degree of turbulence” caused by the rising bubble does not prevent particle and bubble to flow in close proximity. Upon collision, the particle slides on the bubble surface for a period of time. If the particle is hydrophobic, attachment occurs when the “sliding time” is longer than the “induction time”, which is the time required to thin and rupture the intervening liquid (usually water) film forming a three-phase contact angle. While the induction time is largely influenced by the degree of hydrophobicity of the particle, the degree of turbulence is governed by the bubble size. Generally, direct control of bubble size is not exercised by most mineral processing practitioners, in spite of its obvious importance. Studies to model the effect of bubble size on particle collection using fundamental approaches have been conducted (e.g., Anfruns and Kitchener, 1977; Webber and Paddock, 1983; Yoon and Luttrell, 1989; Dai et al., 1999). However, these models have been validated under highly idealized laboratory conditions (micro-scale experiments using single minerals and uni-sized bubbles), far from resembling those existing in practical industrial applications. Fundamental studies to interpret the effect of bubble size on particle collection in industrial environments are largely absent in the literature. Partly because of this lack of practical knowledge, many mineral processing practitioners perceive laboratory “bubble size” studies to be valuable academic exercises, but not something that can be directly applied to daily production issues."

Jan 1, 2011

By David J. Kerr, Robert Mason

"From1927 to1989, the Hornemineproduced53.7 Mt of ore grading 6.1 g/t Au and 2.2% Cu from two large volcanogenic massive sulphide deposits composed primarily of pyrrhotite, pyrite and chalcopyrite. The ore bodies were hosted by a package of chlorite-sericitealtered epiclastic rhyolite tuffs which were deposited in a narrow palaeo-graben located on the flank of a major felsic volcanic centre. M ineralizingfluids percolated upward through the permeable footwall rocks and were further focussed along syn-volcanic, graben-bounding faults. Sulphides were deposited by a process of sub-seafloor replacement of the rhyolite tuffs.Gold-copper-(zinc) mineralization, including ore zones mined between 1985 and 1989 as the REMNOR ore zones, is present throughout the 900 m of felsic volcanic stratigraphy at the Horne. All the deposits were formed by syn-volcanic hydrothermal processes active during felsic volcanism. There is no evidence to indicate that any economic gold mineralization was introduced by a post-volcanic hydrothermal episode.RESUMEDe 1927 a1989, /amineHorneaproduit53.7 Mt de minerai avec une teneur de 6.1 g/t Au et 2.2% Cu provenant de deux grands amas de sulfures massifs volcanogeniques comprenant esentiellement de la pyrrhotite, de la pyrite et de /a chalcopyrite. Ces gites font partie d'une séquence de tufs rhyolitiques epiclastiques chloritises et sericitises qui ont ere déposes dans un paleo-graben étroit situe sur le flanc d' unimportant centre vo/caniquefelsique.Lesfluides mineralises ont circule de bas en haut a travers /es roches perméables sous-jacentes; ils ont été également canalises par les failles syn-volcaniques en bordure du graben. Les sulfures se sont déposes par remplacement des tufs rhyolitiques immédiatement et sous /e plancher océanique.Les zones minéralisées en or et cuivre (±zinc) - y compris celles qui ont ere exploitees au cours de l’opération Remnor (1985-1989) - se retrouvent, sans discontinuité, à travers les roches volcaniques felsiques dont l' epaisseur atteint 900 m. Ces gites se sont formes par le biais d' un processus hydrothermal qui ag issait pendant le volcanisme felsique. II n'y a aucune évidence de minéralisation aurifère d'importance économique qui soit postérieure a l' activité hydrothermale syn-volcanique."

Jan 1, 1990

By Peter R. Drummond

THE paper consists of four sections: (1) a discussion of early work; (2) presentation of the results of a chemical investigation of Falcon-bridge nickel-copper blast-furnace matte; (3) application of the results of this investigation to mattes in general; and ( 4) a summary of conclusions. All general discussion will be confined to the fundamental system of ferrous-cuprous sulphides (FeS-Cu2S). Nickel-, lead-, and zinc-bearing mattes will be treated as minor varieties of the parent system. DISCUSSION OF EARLY INVESTIGATIONS Matte investigations may be divided into three classes: first, those treating the sulphides as alloys-theoretical studies of the system FeS-Cu2S, such as those of Hofman (ll)t or Carpenter and Hayward (2); second, chemical research on mattes made under smelter conditions, such as that carried out by Hawley (3) or Avetision ( 4); third, combinations of the . above, such as the investigations of Gibb and Philp (5) or Fulton and Goodner (6). Much research in the first of these classes, including determinations of . freezing points and of data for structure-composition diagrams of the system FeS-Cu2S, was carried out in the period 1890-1910. LeChatelier and Ziegler (1, 13) proved that FeS, when heated alone above its melting point, dissociated in part, and Friedrich ( quoted by Fulton, 6) showed the same for Cu2S. The reactions may be expressed by the following equations: [xFeS yFe + yS (volatilized)+ (x -y)FeS xCu2S )'Cu+ yS ( vohtilized) + (x -)')Cu,S ] Sulphur is lost by volatilization, leaving a melt of metallic iron plus ferrous sulphide in the one case, and of metallic copper plus cuprous sulphide in the other. If the mixed sulphides are heated far above their melting points, there results either an iron-rich matte containing Fe-FeS-Cu2S or a copper-rich matte containing FeS-Cu2S3-Cu, depending on the relative amounts of each sulphide in the mixture.

Jan 1, 1940

By Paul J. Cascone

This paper will discuss the science behind the development of a unique gold alloy for dental prosthetic applications. The alloy (GOLDTECH BIO2000) contains 99.7% gold providing unquestioned biocompatibility and unsurpassed esthetics. The topics discussed are: (1) How the alloy meets the functional requirements of a porcelain-fused-to-metal dental alloy. (2) How the alloy color affects the esthetics of the restoration and why the color of gold is best. (3) Overcoming the intrinsic malleability of gold when grinding the alloy surface. (4) Preventing the oxide color from interfering with the alloy esthetics. (5) Attaining excellent porcelain adhesion. (6) How the design of the restoration allows for the production of single and multiple unit restorations. Gold 2003

Oct 1, 2003

By F. F. Langford

"The Athabasca Basin occupies about 100,000 km2 of the northwest corner of Saskatchewan with its western margin extending about 50 km into Alberta (Fig. 1). The basin is filled with a Helikian sequence of predominantly fluvial sandstones up to 1600 m thick. The sandstone beds are generally flat-lying, and rest unconformably on a crystalline basement which consists mostly of granitic intrusive complexes and quartzfeldspar- biotite gneisses. The basement rocks represent Aphebian sediments and Archaean basement rocks that were metamorphosed and remobilized to varying degrees during the Hudsonian Orogeny (ca 1800 Maj.Since 1968, three mining camps and several substantial unconformity-type uranium deposits have been discovered in the area (Figs. 1 and 2). These deposits lie along the unconformity surface, partially enclosed in sandstones, and partially in the basement rocks. The major deposits have elongate, pencil shaped orebodies that are parallel to the strike of underlying graphitic biotite gneisses. The total tonnage of uranium is in the order of 150,000 to 200,000 tonnes and mining grades range from 0.5 to 2.5 per cent U3O8.IntroductionUranium exploration started in Saskatchewan in 1945 when Jolliffe and Murphy headed field parties to investigate uranium occurrences on the north shore of Lake Athabasca (Kupsch, 1978). Their investigation lead to the development of the Beaverlodge camp in the following years. Some of the early prospectors were impressed by the fact that the uranium occurrences at Beaver lodge were centred on a thick sequence of unmetamorphosed arkosic redbeds which are now called the Martin Group. This sequence was referred to as the Athabasca Series by Christie (1949), and although some occurrences of uranium were found near Stony Rapids and Black Lake, the vast expanse of Athabasca sandstones south of Lake Athabasca was generally regarded as unpromising."

Jan 1, 1986

The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members Ñ the Universities of Queensland and Sydney and the CSIRO1, and by its industry members Ñ BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining.

Jan 1, 2001

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004