Search Documents

By C. Guo, R. J. Chalaturnyk, M. MacKinnon, J. D. Scott

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd. oil sands plant. Over the past years (since 1996), there has been a marked change in the densification behaviour of MFT in the MLSB. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings) at the area with intense microbial activity. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. It may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program was carried out to study the mechanism leading to the rapid densification phenomenon. A review and discussion of the research program is given and some results from the field investigations and small-scale column tests are presented in this paper.

Jan 1, 2007

Abstract - A method to extract certain types of error variance information from paired data is presented, which constitutes an important tool for the calibration of Gy’s formula for variance predictions in the sampling of broken ores. The research summarized here complements publications by others on geochemical precision. The model and method proposed for treating duplicate data provide a practical means of deriving separate estimates of the purely analytical and aliquot sampling variances, from a unique set of duplicate assays, and, hence, proposes a new avenue for estimating effective mineral grain size.

Jan 1, 1998

By Guy Chevalier

QCM?s pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented. This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.

May 1, 2003

By M. Xiao Bo

In recent years, there has been a heightened interest in the hydrometallurgical processing of sulfide ores and concentrates (especially copper sulfide ores and concentrates) mostly in the USA and Chile. Currently, hydrometallurgical operations account for about 30% of the primary copper production. In the present research, the leaching phenomena of IOCG (iron-oxide hosted copper-gold) ores and concentrates were studied. The IOCG ore, which is characterized as having a predominant amount of magnetite with fine chalcopyrite, is currently the center of attention for new copper resources. Heap leaching of IOCG ore is desirable because of its low cost. However, the leaching characteristics of the ores and concentrates and the mechanisms of copper leaching require investigation. This study defines the factors, which affect the leaching operation, such as the ORP, pH and oxidizing agents. Based on these results, the optimal leaching conditions are provided for pilot column leaching test and ultimately, commercial operations.

Jan 1, 2007

By M. Amsden

"Since the computer program is far from complete this must be only a brief progress report on the computerization of flotation metallurgy at the Ecstall concentrator at Timmins.Ecstall is currently treating about 10,000 tons per day of two different ore types. One is a low sulphide copper-zinc ore, the other is a high sulphide lead-zinc-silver ore. The concentrator is divided into three individual grinding and flotation circuits. In effect there are three mills under one roof. Normally there are two circuits on copper-zinc ore and oneone lead-zinc-silver ore. At this point in time one of the copper-zinc circuits is under computerized metallurgy control.The first step in this control is the use of an ARL on-stream x-ray analyzer, coupled with a Honeywell 21 computer which types out assays and recoveries for each individual circuit. Our approach to a computer program was to keep it simple. The program was written to coincide as closely as possible to what an operator would do in the performance of his duties based on the in-formation he was getting from the x-ray analyser read-out. Initially, computer control was put on just the copper circuit of the ""A"" Division, controlling the collector addition at three points in the circuit; primary, secondary, and scavengers. The control was based on recoveries and the grade of the copper concentrate. Targets like 95% recovery and 24% copper concentrate grades that it was felt the circuit could achieve were set to start with. It quickly became apparent that this alone was not enough because if on a certain ore the best recovery that could be made was only 94.9% the computer kept calling for more reagents until the circuit was completely out of control. On another ore it might have been quite possible to get 96% recovery but when the set point of 95% was reached the computer stopped trying for any more. To overcome this problem a very simple optimum seeking program was devised by one of the Ecstall staff and it has worked very satisfactorily since being put into use in July 1970.In the copper float only the two collectors R-208 and the xanthate R-317 are under computer control. The addition of frother and depressant is left to the operator. The flotation cells have automatic level controls which can be adjusted by the operator. pH is controlled automatically through a lime loop-sensor arrangement."

Jan 1, 1971

By Frank Lemy

This paper presents an application of digital face mapping in an underground mine. Based on photographs it was possible to construct discontinuity maps, which were used to characterise the rock mass. The results were compared favourably with values obtained through scanline and area sampling mapping for the same site. The case is made for digital mapping as a safe, fast, and efficient way to characterise rock mass structure for engineering purposes.

May 1, 2001

By Euler De Souza

"The uninterrupted operation of a ventilation system is critical to ensure the mine meets its scheduled production and, as important, is vital to the health and safety of all personnel working underground. Those operating the mine ventilation system must have fundamental engineering training in the art of fluid dynamics and have a good comprehension and control of the mine ventilation network. Ventilation management by untrained and inexperienced personnel may result in serious consequences when the system becomes ineffective. This paper shares observations and experiences pertinent to the occurrence of upset conditions as a result of the improper design and operation of mine ventilation systems. A series of real life case studies are presented to describe disruptions to mine ventilation systems and the gradual deterioration of system operational efficiencies leading to eventual failure. Special focus is given to mistakes made and on the resulting serious consequences. The case studies also demonstrate how each upset condition was resolved, permitting the mines to safely resume production activities.INTRODUCTIONThe ventilation of operating mines is a continuously changing and evolving system; upset conditions will occasionally occur, but should be promptly resolved in order for the system to function properly, according to design, and in compliance.Those designing, managing or operating the mine ventilation system must have pertinent training and have a good understanding of fundamental ventilation concepts to be able to devise and implement engineering solutions to day-to-day challenges. Realistically, the operator must also have extensive practical experience and be able to effectively apply operating procedures, design criteria and ‘best practices’. They must be able to, on a daily basis, evaluate the mine ventilation system, determine and locate any problems, understand the causes of each problem, find a solution, and promptly and efficiently correct those problems.Ten case studies are presented to demonstrate how fundamental design or operational mistakes can lead to adverse conditions or to catastrophic consequences, how detailed on-site engineering assessments can be employed and how simple, low cost, engineering solutions can be implemented to successfully resolve the issues and return the ventilation system to compliance, permitting the mines to safely resume production activities."

Jan 1, 2019

Toronto 2013 Proceedings

May 1, 2013

By Normand Bédard

This presentation highlights Cambior?s initial approach for recruiting and retaining its international employees, the importance of proper preparation and the support needed to ensure a competent and stable workforce. In general, most of the training and information available for human resources personnel prepares the specialist for handling various aspects of labour relations, recruitment and hiring, benefits administration, employee relocation, etc. This is usually done in a Canadian context. Only recently, has more specialized training been developed to prepare human resources practitioners for the complex issues related to expatriate employees and dealing with human resources issues in other countries.

May 1, 2003

By D. Royston

Reducing SAG Mill feed size has been a major trend in recent years. ‘Mine to mill’ strategies have reduced blasted-rock size, and in a growing number of operations reducing the primary crusher CSS and/or adding additional crushing upstream of the SAG mill have reduced rock feed size. While reducing feed size will increase SAG mill throughput, issues arise in terms of retaining charge in the mill, exposing the shell lining to impact damage, and maintaining milling performance should the pre-crush system shut down. This paper reviews the past experience on pre-crushing for SAG mills and provides an analysis of liner design (in particular grates and shell liners) for pre-crushed feed.

Jan 1, 2012

By Dwayne D. Tannant

This paper presents a summary of results from a questionnaire sent to surface mines in western Canada seeking information on haul road design, construction, and maintenance. There has been a marked increase in the size of the trucks used over the last decade with some mines now using trucks with a payload capacity of 360mt. Consequentially, geometrical elements of haul roads, such as width, have been enlarged to accommodate larger trucks. Most haul roads are constructed on the basis of past experience without use of formal design procedures. With the introduction of larger haul trucks, problems related to rolling resistance, deterioration, and maintenance of the haul roads have become more important. This has lead to adoption of more rigorous design methods for roads at some mines, most notably for the oil sand mines operated by Syncrude Canada Ltd. A summary of the evolution of haul road designs implemented at Syncrude Canada Ltd. is presented.

May 1, 2001

By L. Chunpongtong

ABSTRACT Oil sands production occurs on a massive scale, making orebody estimation a challenge. In rainy conditions, operators can have difficulty accessing ore at the mapped location. Without enough inventory as a buffer, the high-cost stockpile is depleted quickly, necessitating the removal of significant amounts of overburden and interburden to meet plant feed requirements. The inventory curve—a plot of ore inventory on a period-by-period basis—plays an important role in selecting an appropriate scheduling scenario. This paper presents a programmable method for creating an inventory definition by using a pit optimization tool.

Jan 1, 2014

By Jacek Paraszczak

As the deposits located closer to the surface are getting depleted, more and more Canadian mines produce ore from considerable depths. Deep mining represents a number of serious challenges including high rock temperature. Conventional diesel powered loadhaul- dump machines and trucks so widely used in metal mines constitute an additional source of heat and noxious gases. Due to this, they have a substantial adverse impact on a quantity of fresh air required and a cost of ventilation, particularly since the mines have to meet more and more stringent regulations in this respect. In this context, the paper examines possible alternatives for diesel powered equipment, both these commercially available as those at the stages of prototypes or under development. They are reviewed with regards to their principles, required infrastructure, stage of technology development and its progress. The questions of their flexibility, practicality and economic viability are also addressed. Following the above a potential for their implementation and possible benefits (if any) in the conditions of deep Canadian mines is discussed. The paper concludes with short to medium term predictions concerning the most promising drive alternatives for vehicles destined to operate in deep metal mines.

Feb 1, 2008

By John Monhemius

Looking back over the past half century, it can be seen that the growth in the importance of hydrometallurgy for the production of non-ferrous and precious metals almost exactly parallels the rise of the environmental movement and its principal NGOs, such as Greenpeace and Friends of the Earth. The paper will review important landmarks in the development of the science and technology of hydrometallurgy and show how many of these have been influenced by pressures on the industry brought about by environmentalists. Successful innovations as well as commercial failures will be considered and reasons for the success or failure will be analysed and lessons drawn to guide future developments.

Jan 1, 2014

By J. B. C. Wu, B. McKee

"Mining along with subsequent processing of the minerals often presents conditions where a wear- and/or corrosion-resistant alloy is needed to minimize downtime and maximize efficiency. This paper is intended to give an overview of the alloys that are currently being used, as well as those developed in recent years that could be used in the mining industry. Emphasis will be put on the iron-, nickel-,cobalt-based alloys and composites containing a variety of carbides. The characteristics, properties, product forms, and methods of application are presented. In addition, examples of the actual use of these wear-resistant materials are illustrated.IntroductionPreventing wear and corrosion is important in any industrial operations. In the mining industry, the process equipment typically suffers many different types of material degradation. Abrasion, impact, erosion, metal-to-metal wear and corrosion are typically encountered. Each situation requires different material characteristics to retard the degradation process. Therefore, it is essential to understand the characteristics of the materials and the effects of the alloying elements.There are four common classes of metallic materials for resisting wear and corrosion; namely, iron-based alloys, nickel-based alloys, cobalt-based alloys, and carbide-containing composites. Each class of material has its own characteristics. Depending on the chemical composition, the materials within each class can be vastly different in properties. In recent years, there have been materials developed in each of the four classes using the knowledge of the metallurgical principles and the effects of the alloying elements on the material degradation process.To use a wear-resistant alloy, it is also necessary to understand the available product forms and their application methods. Weld overlaying is a traditional way of using these alloys (Wu and Redman, 1994). In recent years, thermal spray is becoming popular. For applications where over-laying and spraying are impractical, solid components can be made by a variety of casting and powder metallurgy techniques. They can also be fabricated from the wrought products.To select a proper material for an application, it is important to understand not only the characteristics of the wear-resistant materials but also the degradation process. Due to the complexity of the processing environments, past experience is also helpful in making the decision on the material selection."

Jan 1, 1997

By Chris D. Veldhoen

If you ask most diamond drillers if they have ever encountered methane gas, the answer would probably be yes. This paper explores a serious methane gas explosion that the author experienced while diamond drilling at a northerly Ontario mine. It is hoped that by documenting this event, people may be alerted to the hidden danger posed by confined methane in underground workings. Methane gas tends to be a problem the deeper you get in any Canadian gold mine. Common procedure when encountering methane is to take readings at the collar of the hole and at different lengths from the source. Monitoring continues until the readings drop below 0.25 ppm. Methane is a tasteless odorless gas that is usually locked up in the seams of the rock or is a product of decaying organic material. Occasionally, the gas is released abruptly over a short period of time. Sometimes the gas can continue to vent for months or even years. In small concentrations, methane is relatively safe. In concentrations under 0.25 ppm methane gas is considered safe to work around. Concentrations over 0.25 ppm can become dangerous. During the summer of 2001, Chris Veldhoen was drilling at a gold mine in Ontario. There were three electric hydraulic diamond drills on the 39 meter level, approximately 5200 feet deep. Two Longyear LM 55 drills were about 40 feet apart and another LM 75 was about 2000 feet away. The two LM 55?s were set up to drill holes no deeper than 350 meters. All three drills had been set up on the same spot for more than a month. None of the three drills had ever encountered methane gas in the entire time they had been drilling on the level. On the day shift of July 13 2001, the driller on Chris? cross shift hit a small pocket of gas. He tested the hole and got a reading above 0.25 ppm. He proceeded to rope off the area with a ?DO NOT ENTER - METHANE GAS? sign and a rope denying access beyond the sign. On Saturday, July 14, Chris was instructed to install a Margo plug in the hole that was emitting methane gas. Methane is usually odorless, but occasionally when encountered underground, is accompanied by a rotten egg smell. As he walked to the drill, he could not smell methane gas. He proceeded to test the hole and got a reading of 0.22 ppm methane. This number was in the acceptable range for drilling, but he plugged the hole anyway.

May 1, 2004

By R. C. Gilmore, J. McMack, G. E. Bogin, J. F. Brune, C. DeRosa

"Researchers at the Colorado School of Mines are designing and building a 1:40 scaled physical model of a fully operational longwall coal mine. The purpose of the model is to minimize the occurrence of methane explosion hazards by testing various ventilation strategies and determining optimal methane sensor placement throughout the longwall face. Fluid scaling factors were analyzed using Computational Fluid Dynamics software Ansys FLUENT™ at both full and 1/40th scales. Researchers were able to identify key scaling factors and subsequently developed suitable flow parameters that would maintain full scale accuracy of flow patterns in the 1/40th model. KEYWORDS Coal, Longwall, Methane, Explosion, Scale Model, Ventilation, Fluid Dynamics, Richardson, Gob, Porous INTRODUCTION Mine ventilation systems are a key component for ensuring a safe working environment by introducing fresh air from the surface and diluting explosive gases and hazardous contaminants. This holds true for longwall coal mines where the emission of flammable methane gas from the longwall face as well as the gob can create explosive mixtures of methane and air. Therefore, an effective ventilation strategy can help mitigate the potential for accidents within a mine. Developing an effective mine ventilation system (MVS) requires a detailed understanding of the physics of gas transport and how this relates to specific geometries and obstructions in the face. Researching this phenomenon requires the development of computational fluid dynamics models capable of simulating fluid flow and methane species transport that can be validated through physical experimentation. Unique site conditions determine ventilation layouts for every coal mine. Researchers have designed a 1/40th scaled physical model of a longwall coal face and adjacent gob that includes movable shield supports and a movable shearer with rotating cutter drums that can be adjusted to a variety of ventilation conditions. The proposed work will address the need for an improved Mine-wide Atmospheric Monitoring System (AMS), and provide the ability to link existing MVS models with AMS in real time. By accurately representing the coal face, the gob area and the mining equipment, gate roads and bleeder entries, the scaled model accurately represents all relevant structures, geometry, and dynamic conditions. A Plexiglas cover allows full optical access for sensor equipment as well as visual inspection of the fluid flow and species transport."

Jan 1, 2019

By W. Kempson

"Mining Companies have producing assets in increasingly diverse portions of the world. It is not uncommon that the owner, the design team, the mine contractors and the operators are all based in different countries. While these assets are always subject to the regulatory requirement of those countries there have not been international standards available to review and evaluate these assets. This becomes particularly important when considering safety critical items such as tailings dams, vertical shaft systems and autonomous vehicles to highlight a few. The work currently being completed in ISO ensures these standards will be available and will be generated by and subscribed to on an international basis, thus removing the potential for patriotic partisanship and ensuring safe and predictable systems are installed. This paper will discuss the benefits of the international standards, the structure of the teams and working groups who are generating these standards as well as the process by which the standards are generated. This will allow insight into the creation of the standard and will aim to demonstrate the “neutral” and technically strong manner in which the generation of these standards is achieved. In addition, the paper will discuss the standards which have been produced in the last five years as well as the current standards which are in place. The finale will discuss upcoming work and the timelines in which it is anticipated these will be completed. INTRODUCTION Mining Companies have producing assets in increasingly diverse portions of the world. While these assets are always subject to the regulatory requirement of those countries, there have not been international standards available to review and evaluate these assets. This becomes particularly important when considering safety critical areas such as vertical shaft systems, tailings dams and autonomous vehicles to highlight a couple. The work currently being completed in the International Organization for Standardization (ISO) ensure these standards will be available and will be generated by and subscribed to on an international basis, thus removing the potential for patriotic partisanship and ensuring safe and predictable systems are installed. The ISO/TC 82 – Mining was founded in 1955. This was an active committee until it was thought that the standards at the time were adequate and the Technical Committee was put on “Care and Maintenance”. In 2012 countries lobbied ISO to pull this committee from dormancy and restart it, this happened in in the same year."

Jan 1, 2019

By M. Ataka

Magnesium alloys are not easy to plastically deform at room temperature and may suffer from edge cracking at high reductions, especially during sheet rolling. In this study, the authors attempted to improve the rollability by the low-temperature hot rolling method, in which the rolling temperature range is lower than that of hot rolling, and also by the edge-heating method, which locally heats sheet edges.

Jan 1, 2006

By Kathy S. Kalenchuk

Damages have been observed in shafts, backfill infrastructure and the slick line at the Leeville Mine. Shaft damage (shearing and spalling of the concrete liner) is attributed to mine-induced rock mass deformations concentrated where regional faults intersect the shafts. Aggregate bin, mixer station and conveyor drive damage (shotcrete shearing, heave of concrete floor slabs and bending of a vertical steel beams) is attributed to rock mass squeezing induced by elevated magnitudes of the vertically orientated major principal stresses. Separation of the slick line has occurred do to extension of the stressshadowed rock mass immediately above the mined out areas. Three-dimensional numerical models have been developed and calibrated to simulated rock mass deformations with magnitudes similar to those believed to have produced the observed damages. By stepping through the mine sequence, models reproduce deformations at the same mining stage as when damage has occurred. Calibrated models have been used to forward project further damage over the remaining mine life.

Jun 1, 2012