Search Documents

A series of field and laboratory evaluations were conducted in order to characterize the effects of a Mann+Hummel SMF-AR® diesel particulate filter (DPF) system on the aerosols and criteria gases emitted by diesel engines. This system, with a durable sintered metal filter media and available active regeneration via an on-board electrical heater, has been considered for retrofitting diesel engines used in light- and medium-duty underground mining applications. Two DPF systems were installed on a forklift and locomotive from the underground mining fleet of the Vale?s Creighton Mine and evaluated over a 1,500-hour trial. This evaluation was complemented with field and laboratory emissions tests. The field tests were performed on the vehicles while at the Creighton Mine surface shop. During those tests, the emissions were assessed for the engines operated at hydraulic stall, high idle, and low idle conditions. The laboratory tests were executed at the diesel engine emissions laboratory at the National Institute for Occupational Safety and Health (NIOSH), here the DPF removed from the forklift was further evaluated at four steady-state engine operating conditions as well as at transient conditions using a custom-designed duty cycle. Very similar methodologies were used during field and laboratory tests to measure concentrations of aerosols and criteria gases in the diesel exhaust, both upstream and downstream of the DPF system. The concentrations and size distributions of aerosols were measured using a fast mobility particle sizer spectrometer, in exhaust diluted by a partial flow dilution system. The concentrations of CO2, CO, NO, and NO2 were measured in the raw exhaust using a Fourier transform infra-red spectrometer. Both field and laboratory emissions tests showed that the evaluated DPF systems were very effective in reducing aerosol emissions from all tested engines, and for all test conditions. The systems were found to have minor effects on gaseous emissions from those engines. The findings from this study should help the mining industry to better understand the benefits and challenges of using DPF systems to control the exposure of underground miners to diesel aerosols.

Aug 1, 2013

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By N. Katsikaros, A. Lewis-Gray, P. Richards

"To optimize gold recovery in complex leach-to-electrowinning processes, Gekko Systems developed the Gekko resin exchange column (G-REX) as an intermediate step, using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin. Operational experience has been gained at the Castlemaine Goldfields Ballarat gold mine. In near-continuous operation since 2008, the Ballarat plant treats unclarified concentrate leach solution. The extension of this technology to higher throughputs and more complex chemistry is discussed.RÉSUMÉ Afin d’optimiser la récupération de l’or dans des procédés complexes impliquant la lixiviation suivie de l’extraction électrolytique, Gekko Systems a développé la colonne Gekko de résines échangeuses d’ions (G-REX) comme étape intermédiaire, à l’aide d’une résine hautement sélective pour la récupération de l’or qui permet d’isoler les métaux contaminants. Gekko détient la licence exclusive pour la résine AuRIX®100 produite par Purolite, et la colonne G-REX a été spécifiquement conçue pour cette résine. C’est à la mine d’or Ballarat de Castlemaine Goldfields que l’expérience opérationnelle a été acquise. L’usine de Ballarat, en exploitation quasi-continue depuis 2008, traite une solution concentrée non clarifiée de lixiviation. L’extension de cette technologie à des capacités supérieures et à une chimie plus complexe est examinée."

Jan 1, 2017

By L. Bichler

Lightweight magnesium alloys are gaining in popularity for applications in the automotive and aerospace industries, Their use, however, remains limited due to their relatively low strength and creep properties. Lost Foam Casting (LFC) is a new casting process and the strength of foam cast magnesium alloys has not been investigated in great detail thus far, In this research, magnesium alloy AZ91 E and three new alloys were cast by the LFC process to study the effect of varying aluminum and manganese content on the alloy's tensile properties, The study reveals, that the tensile strength of the magnesium alloy is closely related to the relative amount of aluminum in the system. Formation of ß-Mg17Al12 phase was seen to significantly affect the yield strength and ductility of the alloy, Furthermore, formation of manganese intermetallic compounds was seen to effectively increase yield strength of the base alloy, Individual alloy morphologies were analyzed via optical and SEM techniques.

Jan 1, 2004

By Arnaud Faucher, Amar Sabih, Sudarshan Martins, Tristan Martin, Sami Makni, Peter Radziszewski, Poorya Hosseini, Francois-Raymond Boyer

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By B. Karnath, K. Guha, S. Tandon

At Jhagadia Copper Ltd (India), Copper is produced through secondary route using Top Blown Rotary Converter (Kaldo Furnace). The basic raw material being treated includes Matte-slag Reverts, Copper Cakes, dross & Cement, Oxide Ore, Low S bearing Concentrates & various metallics along with high grade copper scraps. The plant has capability to refine & produce Blister grade copper from Kaldo furnace as well as PS Converter . Blister is fire refined in Anode furnace & electro refined in Refinery to produce cathode copper. Our product , Copper Cathode , has already been established in the market as its quality is better than 'LME Gr'. The paper deals with the experiences encountered during commissioning & stabilization of the plant.

Jan 1, 2007

By P. Taskinen, A. Jokilaakso

The Flash Smelting Process for copper and nickel production has been one of the most successful new metallurgical process developments in the 20th century. The experimental data from laboratory scale investigations of studies has produced information and insight into the reaction mechanisms and kinetics of the flash reactions of copper concentrates. Advanced computer models coupling chemical reactions with a Computational Fluid Dynamics (CFD) software became possible with the development of commercial CFD software together with increased computing power. Currently, there are both experimental and CFD modelling, including also CFD–DEM coupling (Discrete Element Method), studies ongoing for investigating the kinetics of matte – slag reactions in the flash smelting furnace (FSF) settler. The ultimate goal of the modelling work is to develop a comprehensive FSF model for studying the behavior of changing raw materials, both primary and secondary, and distribution of their elements between the matte, slag, and gas phases. The use of User-Defined-Functions (UDF) is one way to digitalize metallurgical knowledge and experimental information to be used for supporting process experts and development of artificial intelligence applications in metallurgy. In this paper, a review of the development of the FSF reaction shaft modelling and experimental investigations, and the current work for the settler reactions’ experiments and modelling are presented. INTRODUCTION The Outotec Flash Smelting process (Bryk, Ryselin, Honkasalo, & Malmström 1958) has been used in the copper and nickel industry for 70 years with continuous support from experimental investigations by many research groups in academia, among others Jorgensen and Segnit (1977); Jokilaakso, Suominen, Taskinen and Lilius (1991), Chaubal and Sohn (1986), Kim and Themelis (1986), and in industry Mäkinen and Jåfs (1982); Kojo, Lahtinen and Miettinen (2009); Tuominen, Pienimäki and Fagerlund (2016). It has been developed also for pyrite and lead smelting (Asteljoki, Sulanto & Talonen, 1984). A schematic illustration of the FSF and other main parts of the process is depicted in Figure 1. Also, two and three dimensional physical water or gas models have extensively been used in product and process development (Lilja & Rajainmäki 1995). During the recent decades, computer based models have increasingly been adopted in the FSF research and development (Ahokainen & Jokilaakso, 1998); Ahokainen, Jokilaakso, Taskinen & Kytö, 2006; Hahn & Sohn, 1990; Jorgensen & Elliot, 1992; Zhou, Zhou, Chen & Mao, 2014; White, Haywood, Ranasinghe & Chen, 2015) to name a few, but also in supporting engineering and sales of the technology (Miettinen 2017). Even though the reactions of the sulfidic concentrate particles have been included in the reaction shaft modelling, the complete FSF model with both gas-solid/drop and molten slag/matte drop has so far been and still is too demanding for today’s computer hardware.

Jan 1, 2019

By Warwick D. Bullen

Gold mining in the Yellowknife area of the Northwest Territories started long before the concept of sustainability entered the academic literature and by the time the term enjoyed widespread public acceptance, the Yellowknife gold mining industry was in its sunset years. Nevertheless, the city of Yellowknife will long outlive the gold mines that it was founded on, demonstrating that not only can mining build sustainable communities, but that sustainable mining as a concept is an entirely valid precept. To this effect, the authors examine the complex economic and social aspects of the gold mining industry in the Yellowknife area over the last 70 years.

May 1, 2004

By Zhen Lei

In Alberta, Canada, heavy industrial projects are constructed using a prefabrication approach: spools and pipes are produced in the factory, and are assembled into modules that are transported to the industrial plants for installation by mobile cranes. Planning the onsite mobile crane operations is critical to the project budget and schedule. However, due to the large magnitude of industrial projects, manual heavy lift planning is tedious, and the results are not particularly responsive to site changes. This paper introduces an integrated mobile crane management system developed by PCL Industrial Management Inc., in collaboration with the University of Alberta, which investigates crane location selection and path checking for field module assembly. The project information is stored in a database, and the proposed system retrieves data, performs the calculations, and records the results back to the database; the calculations involve automatically selecting locations for the mobile crane, considering the crane capacity, lifting range and utilization. Lift paths for modules are checked for feasibility based on selected locations, satisfying the site and crane configuration constraints, and crane walking paths are planned if needed. The designed system is tested in an industrial project to validate the effectiveness of the system.

Aug 1, 2013

By C. A. Clark

The Chagres Smelter is located 80 kilometres north of Santiago - Chile, in the middle of an agricultural valley which is also one of the poorest districts in the country. This condition sets the main focus for the smelter's Corporate Social Responsibility (CSR) programmes, which ultimately aim at building self sustainable social and economic capital in accordance with the local capacities. With the help of Anglo American's SEAT (Socio Economic Assessment Toolbox), a corporately developed instrument designed to help the operations understand the needs of the communities and the impacts of those operations, the Chagres Smelter implemented several programmes, such as the CETTA (Experimental and Applied Technology Transfer Centre) programme. This project started in 2003, and consists of creating a centre for the transfer of sustainable techniques and skills for the small agricultural and livestock producers that live in the rural areas near the Chagres Smelter. Its main impacts are: Improved production quality (goat cheese and bee honey) and access to relevant markets, improved training and self-sustainability levels of producers, enhanced socio-economic level of the District's inhabitants by improving their income earning opportunities and technical knowledge, creation and promotion of a local brand as a symbol of quality products from the valley and a positive environmental impact of good breeding and native flora protection practices in the area. Other relevant social programmes are the 'Environmental Strivers', which created a recycling centre in the community; and the 'Beautiful Valley" project, which provides management knowledge and skills to local youngsters and leaders who can contribute to finding solutions for local environmental needs.

Jan 1, 2007

By M. Feinendegen, Ph. Siebert, C. Clauser, K. Willbrand, M. Ziegler

"Three institutes of RWTH Aachen University collaborate on laboratory tests and numerical simulations of hydraulically driven fractures in igneous rocks. The project´s target is to enhance the understanding of hydraulic induced fractures for deep geothermal energy exploration. Based on the idea of creating new discrete fractures in hot dry rock (HDR) reservoirs, the current project stage deals with this process on a laboratory scale. Especially for this purpose, a new testing facility has been developed and laboratory tests are performed to verify a hydraulic fracture propagation code based on the extended finite element method (XFEM). The testing facility enables us to initiate and propagate fractures in large samples of dense rock under triaxial confining pressures and to monitor the fracture propagation by extensive measurements. This contribution gives a short introduction to the project‘s background and mainly focusses on the test facility, the experimental procedure and exemplary results.INTRODUCTIONThe most efficient technique to increase the permeability of subsurface rock is to initiate and open fractures by applying hydraulic pressure from a packed borehole-section and to inject fluid into these fractures to propagate them. Since its first use in petro industries to enhance the production of wells in natural gas and oil reservoirs, the interest in targeted creation of hydraulic fractures has increased exponentially. As the key technology to the extraction of unconventional gas from shale, hydraulic fracturing (HF) became a major topic in a heated public debate. Based on the fact that a fracture tends to propagate in a direction perpendicular to the minimal principal stress, hydraulic fracturing has become an established tool for estimating geological stress states in almost any depth. Enhanced geothermal systems (EGS) in HDR reservoirs use engineered fractures as a heat exchanging system for a cycling fluid driving a power plant."

Jan 1, 2015

By Luis R. Fonseca, C. Raimat, C. Wendeler, A. Sanz

"Rockfall barriers are widely known as proven efficiency element to protect infrastructure by catching the rock blocks in the falling direction and absorbing the energy generated by them.It’s common in the project design phase and during installation, fix rockfall barriers for catch a high percentage of the falling blocks and in many cases consider as valid the solution when the barrier can capture all of them. However, in many cases it’s possible to consider the use of these protections, simply to guarantee a secure shed for the traffic and intercept simply the blocks that theoretically hit the road surface.The results of the high-energy rockfall protection barriers type GBE which protect GC-200 road in Las Palmas de Gran Canaria are shown in this paper.The topographic data should be especially detailed observed and even more if you want to apply the technique of ""shadow zone"" with a flexible gallery system. It should be drawn from detailed topographic maps and drawings (photogrammetric restitution) to the scales 1/1000, 1/500, or 1/200; and it is important not to ignore the presence of vertical cuts, tracks, small slopes that modify the trajectories (trampoline effect, hard points that favor the rebounds) and which are not always presented in the drawings.The ""shadow zone"" is defined as the protected area, located at a lower elevation to the line created by the rockfall barrier to except of trajectories of rocks and free from the influence of the deflection of the system under the maximum energy level for which it was designed (MEL)."

Jan 1, 2015

By S. Fahland, P. Vogel

"The Gorleben salt dome has been investigated since 1979 for its suitability as a repository for the disposal of high-level radioactive wastes. The geoscientific surface exploration was followed by underground exploration of the site beginning in 1983: underground excavation work included the sinking of two shafts from 1986 to 1994, the excavation of the infrastructure area and of drifts located in the first exploration area EB1 within the following years. The exploration was interrupted for ten years from 2000 to 2010 as part of a moratorium. After the expiry of the moratorium in March 2010, the geoscientific underground exploration at the Gorleben site was resumed. The investigations were interrupted again in autumn 2012 due to a political decision. The exploration programme included extensive geoscientific investigations: geological exploration, geophysical investigations, mining exploration and mining observation, laboratory tests, in-situ geotechnical measurements, geological modelling and numerical model calculations. To analyse and interpret the results of the in-situ measurements and mining observation geomechanical, thermal and thermo-mechanical model calculations were carried out. One of the main elements of the in-situ geotechnical investigations were high-resolution geothermal measurements performed in boreholes used for geological exploration and geotechnical tests.The geothermal measurements are used to evaluate several geotechnical findings, e. g. drift closure, rock deformation, stress change, and are completed by thermal model calculations to analyse and interpret the results of in-situ measurements and mining observation. The model calculations have been carried out using the special purpose JIFE code. To consider the whole exploration mine with the adjoining host rock as well as the successive excavation of drifts and boreholes in detail a three-dimensional finite-element model was developed. The model calculations are used to analyse the cooling-off of the surrounding rock of the drifts caused by ventilation. The cooling-off of the surrounding rock is an ongoing process affecting the results of further geotechnical measurements in the near field of the drifts. To predict a realistic time and space dependent distribution of the temperature field of the host rock within the exploration area which is influenced by ventilation thermal model calculations are necessary. Comparing the calculated temperature field with the in-situ determined rock mass temperature field within the exploration area EB 1 the results show a sufficient agreement. Furthermore there is very good correspondence, both qualitatively and quantitatively, between the experimental and the calculated findings regarding the temperature profiles including the effects of excavation and ventilation of the drifts."

Jan 1, 2015

Energy benchmarking is widely applied across industries to determine the potential to improve energy performance. Unlike the many technologies for which energy benchmarks and efficiency rating systems are already in maturity, benchmarking of mining processes is still in its infancy. Benchmarking energy usage in mining operations, where energy costs are high and represent a significant portion of overall operating expenses, is challenging due to the uniqueness of each mining operation. Mines vary in terms of geology, geographic setting, ore body geometry, mineralogy which impact the mining method, material handling, processing and waste management. In order to gauge the opportunity for reducing the energy intensity of individual operations and also to compare the energy performance of operations on a global scale, the deployment of new benchmarking methodologies, models and frameworks is necessary. As a step towards the establishment of an accurate framework for benchmarking the energy consumption of mining operations, comminution, one of the more energy intensive mining sub-processes, was selected as the focus of a new energy benchmarking method. The methodologies and processes used to onset fragmentation in a rock mass to the crushing or grinding of rock to a size that is suitable for economic extraction are predominantly dependent on the ore properties. For this reason, site specific factors, such as the size reduction requirements and ore hardness were included in an energy benchmark model so that the energy performance of comminution processes at different operations could be normalized and compared on a global scale. Single particle compression breakage has been identified by several prominent researchers in the field of comminution as the upper limit of energy utilization in size reduction processes. For this reason single particle compression breakage was proposed as the basis of a work index for ores to be used as an input for the benchmark model. Overall, the new method showed that the energy benchmark for mineral comminution can be normalized and subsequently compared for a range of mining operations once the ore hardness has been appropriately characterized.

Aug 1, 2013

By A. Burduk

The traditional approach to managing information flow between a mine underground and overground, applied in copper mines of KGHM Polska Miedz S.A., is mostly based on exchanging spoken information using the mine telephone network and printed documentation. This way of information flow significantly influences effective use of time of a shift foreman employed at a mining division. In order to minimise multiplication of significant information generated as paper documentation, a concept of an IT system module to input basic data concerning operation of the mining division was developed. The idea is based on computer software that permits inputting data in the underground and their immediate sending to the overground. The above-mentioned solution will permit significant reduction of administrative work time that each foreman has to do on each shift. The time saved on filling forms and communication will permit the foreman and the other workers involved in information flow to spend more time for execution of their basic duties. In the case of the supervision employees working in the overground, the IT system will allow all the interested persons to be informed directly, with no necessity to transfer the information on the situation in the given mining division by turns from one to another. On the other hand, saving time on administrative works will permit the foreman employed in the underground executing more detailed inspection of workplaces in his subordinate mine division. Thus, availability of the foreman for the mining division operation will be improved. KEYWORDS

Aug 1, 2013

By S. Borle

The microstructural features produced in friction stir welded AZ31, AZ80 and AZ91 alloys are examined when different welding parameters are applied. The microstructures primarily consist of a-Mg grains with a-Mg + Mg17A112 colonies, however melted films of Mg17A112 are produced in AZ91 alloy when high rotation speeds are applied. When the rotation speeds are slow, or the travel speeds are fast the Mg17A112 were incorporated into the stir zone, however they do not exhibit an elongated lamellar morphology associated with melted films. In the case of AZ80, the extruded base material contains a smaller fraction of Mg17A112 and few of these phases are observed in the stir zones. The results are explained based on the dissolution rate and melting temperatures of Mg17A112 controlling the overall morophology and fraction of phases in the stir zone.

Jan 1, 2011

By Daniel Gendron, Luc Morin

"Concentrate sampling is a growing concern in the world's mining and smelting industry. The main modes of transportation for concentrate to the smelter are by truck or rail car in a bulk form, thereby limiting access to sample extraction equipment. In many cases, concentrate is shipped to a smelter by several suppliers therefore requiring individual manipulation of different customer samples in a safe and reliable manner. The Heath & Sherwood Bulk Product Sampler offers this feature as well as an economical and effortless way of obtaining samples in rail cars or truck boxes.In 1994, Noranda Metallurgie in Rouyn-Noranda, Québec purchased a self contained Bulk Product Sampler to extract samples directly from inside rail cars before unloading the concentrate. After testing and comparing the results with the conventional sampling method, the bulk product sampler proved to be a practical and advantageous solution for concentrate sampling both for the customer and smelter. Since its installation at the Horne smelter in Rouyn-Noranda, the Bulk Product Sampler has been steadily used on rail cars which contain concentrates from around the world."

Jan 1, 1996

By Wei Ye, Lei Li, Xianjian Guo, Feng He

The purpose of the paper is to study the smelting process of copper concentrate with high Cu/S ratio produced in Africa or other areas around the world and theoretically analyze the influence of slag type on the smelting process. The paper has compared the processes used successfully in smelters, including CAPEX and OPEX and other factors, to provide reference for the industry to select the best process under specific conditions. INTRODUCTION At present, a great amount of copper concentrates with high Cu/S ratio, with chalcocite being the major source of copper, have been produced or are about to be produced in the Copperbelt in Africa and other countries in the world. The copper concentrate is usually high in copper (~30–55wt.%) and low in sulfur (~10–15wt.%). The conventional processes of smelting-converting and roasting-leaching-electro-winning for treating this type of concentrate is high energy and materials consumption such as electric power\fuels\flux et al. The direct-to-blister (one-step) smelting process can be considered favorable due to a reduction in processing steps. Up to now, there are four copper smelters in the world operating with the direct-to-blister smelting process. There certainly are problems in the process such as high copper content in the slag, strict operation requirement of slag cleaning electric furnace, etc. Except technical issues, the impact of factors on economical aspect such as power and material cost needs to be considered comprehensively in process selection. In this paper the technical issues of direct-to-blister smelting process, including slag treatment process, were analyzed and the comparison to the conventional processes and economic analysis of direct- to-blister smelting process to treat high Cu/S ratio concentrate were done.

Jan 1, 2019

By D. Sediako

Excessive residual stress in Al engine blocks may result in cylinder distortion which reduces engine operating efficiency. As such, neutron diffraction was used to measure residual strain along the Fe liners and Al, in the hoop, radial and axial orientations with respect to the cylinder axis, at the cylinder interbore region. Residual stresses were subsequently calculated using generalized Hooke's law and related to the microstructure along the cylinder bridge. The results suggest that the residual stresses in the Al interbore region are tensile and increased with depth in the axial direction of the cylinder. The increase in residual stress at the bottom of the cylinder coincides with a finer and more uniform microstructure in this region of the cylinder. The refinement in microstructure at the bottom of the cylinder likely increased alloy strength, thereby decreasing this section's susceptibility to distortion. This study successfully quantified the residual stress profiles in a heat treated engine block and related the stress profiles to an as-cast engine block.

Jan 1, 2011

By É. Poulin, J. Bouchard, E. M. Pérez-García

Process control and optimization have always been crucial aspects in the mineral processing industry, and expectations constantly increase to cope with more stringent security, quality, efficiency, and environmental performances. The main challenges to reduce variability of key process variables, and steer profits to higher values while maintaining sustainability indexes within acceptable ranges come from nonlinear responses and circulating loads. The most commonly implemented control strategies rely on simple PID controllers for practical implementation and maintenance considerations. If arguably good performances are accomplished when these are adequately set up, there is also room for further gains by using more advanced methods such as model-based techniques. There is thus a need for more realistic process and equipment models. Based on advances of the past few decades, this paper introduces an autogenous/semi-autogenous mill (AG/SAG) model to be included in a modular comminution circuit simulation toolbox comprising ball/rod mills, material handling, and classification devices. The proposed mill model incorporates a modified version of the classic comminution equation that makes grinding rates proportional to the energy input. It requires the determination of a selection function (fragmentation rates) and a breaking function (fragments distribution). The former is modelled with an S-shaped curve characteristic of AG/SAG processes and the latter is a size-relative distribution of the produced fragments. The power draw is predicted employing the empirical equation of Austin. The paper also develops a case study to illustrate how the proposed simulation framework can capture the behaviour of an actual plant. Model calibration consists in an optimization problem that search the global minimum of the difference between predicted and measured/estimated size distributions, power draw, solid fractions, etc. Results demonstrate that the mill simulator can mimic an actual process in its operation conditions. INTRODUCTION Comminution is a key stage in the mineral processing industry, obviously because the phases of interest must be liberated to be able to recover them. In general terms, the global performance of a plant depends largely on the efficiency of the grinding circuit and on the material properties such as its grindability, density, and mineral grades. The subject has vastly been studied since as early as the 19th century, when Rittinger (1867) and Kick (1883) developed some of the first empirical models to relate grinding and energy input. The great interest in the subject comes from the fact that this operation is costly and, probably most concerning, highly inefficient. Buckingham et al. (2011) estimated that ore comminution can represent up to 60% of the overall plant power draw. Moreover, only a modest fraction of the power draw effectively translates into rock fragmentation. For grinding, estimates range between 1% and 25%, depending on the reference used, while the rest is mainly lost as heath (Fuerstenau & Abouzeid, 2002; Tromans & Meech, 2002; Bouchard et al., 2017).

Jan 1, 2019