Search Documents

By Robin Perry, Claude Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in a flotation circuit were calibrated using a dynamic grinding/flotation circuit simulator. Predicted mass flow values are multiplied by reagent addition ratios to obtain actual reagent flow. The transfer functions are currently integrated into the distributed control system of Les Mines Selbaie.IntroductionThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970s there have been numerous publications dealing with practical aspect of control of flotation processes. Most plants use a combination of feedback and feedforward controls to reduce the effect of the following flotation process disturbances (McKee, 1991):• changes in throughput;• changes in feed grade;• changes in particle floatability (size, liberation, surface oxidation ... ); and • deliberate changes of setpoint;Feedforward control manipulates variables such as reagent and/or air flow rate to attenuate the effect of disturbances such as changes of feed rate and mineral content. The feed forward strategy is driven by measurements of these disturbances. Feedback control is used to maintain process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by deviation from the set-point, caused by a deliberate change of set-point or disturbances.This paper proposes a method to improve feed forward control schemes by the addition of a simple model for solids transportation. The feedforward strategy considered in this paper is the ratio type, in which the manipulated variable is changed according to a predefmed ratio between this variable and the measured disturbance. A typical example is the ratio of the reagent addition to mass flow of ore.The paper reviews the state of the art in feed forward control strategy applied to flotation processes and describes the method used for predicting mass flow rates. The last section shows an application of the method in the Les Mines Selbaie flotation circuit."

Jan 1, 1994

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively.INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By C. Morlot, C. Auvray, E. Fourreau, J. Talandier

"During the excavation of underground galleries in a rock mass, reorganisation of the stress field around the site results in damage to the surrounding material. In the framework of research undertaken at the ANDRA underground laboratory in France, galleries have been excavated in a Callovo-Oxfordian argillite formation. The damage has manifest as a number of fracture systems in the adjacent rock. Observations have shown that fractures generated during excavation and storage exploitation are able to self-seal during re-saturation of the site in the post-closure stage. Although indirect evidence for argillite self-sealing has previously been reported, from experiments performed both in situ and on samples, no direct observations of self-sealing have yet been made.For the present study, we performed a range of self-sealing experiments using a newly-developed triaxial compression cell placed within a nano-CT scanner with a 10 µm resolution. The body of the compression cell is X-ray transparent, allowing sample healing to be monitored directly. The samples contained an artificial fracture that had been generated in the laboratory, into which a fluid was injected. The fractures were orientated either perpendicular or parallel to the plane of anisotropy of the material. Our initial results demonstrate that when fluid is injected perpendicular to the plane of anisotropy, the flow-rate has no apparent influence on the kinetics of fracture closure. Permeability varies significantly, from 2.10-14 to 2.10-18 m2 over 116 hours. Post-test observations of the fracture lips show swelling that appears to be orientated perpendicular to the fracture plane and therefore parallel to the plane of anisotropy. Initial results for an injection parallel to the plane of anisotropy suggest that, in this case, the rate of flow affects the kinetics of fracture closure. For a flow-rate of 0.25 ml/min, closure begins after around one minute. In contrast, for a rate of 0.05 ml/min, it is necessary to wait several minutes before partial sealing of the zone is observed. The reduction in permeability is again significant, from 2.10-15 to 4.10-18 m2 over 96 hours. After completion of the test, swelling was observed in elongated zones that lie parallel to the fracture plane and therefore to the plane of anisotropy."

Jan 1, 2015

By M. S. Badollet

"IntroductionAsbestos as received by the manufacturer of asbestos products is •in the •form of either crudes or milled fibres processed to different degrees of texture. Frequently, the manufacturer finds that l:ihe fibres as he buys them are not adaptable to his plant processes, and, therefore, it is necessary for him either to contact the mine supplying the material and request a specific texture for the :fibre or to reprocess the fibre in his own plant.When the mine or mill manager is requested to change his milling equipment to produce a special grade of fibre with a specific texture, he would like to comply. However, if he began to make special fibre grades for each customer, he would be in the position of constantly rearranging his milling technique, adding more equipment, or building a new mill. In the end, his mill would he producing hundreds of different fibre grades of varying degrees of texture, which is a difficult accomplishment if he desires to maintain any quantity of production."

Jan 1, 1950

AGENDA ? Company Overview ? Industry Direction ? Technology to support maintenance ? data access, connectivity, process historian, downtime & production reporting. ? Case Studies Company Overview Corporate Offices Client Base ?16 consecutive years of growth & profitability ?#39 of Top 50 Control Companies (Worldwide) ?470 employees ?TSX: MTK Industry Direction Improved visibility into the business so they can: ? Reduce cost through better understanding of where costs are being incurred and making timely decisions. ? Optimize operations while leveraging existing assets. ? Have a single version of the ?truth? ? Deliver reliably to stakeholders on the demand for increased accountability (safety, environmental, regulatory performance etc?). ? Respond quicker to market conditions in order to out perform the competition ? Best in Class approach. Web is becoming the standard user interface.

Apr 1, 2005

By R. D. Brown

"AbstractOver the past five years, tax rates in the Canadian mining industry have skyrocketed upward across Canada, as both federal and provincial governments have sought to increase their share of mining revenues.However, the past few years have not only brought high tax rates to the industry, but also a number of important new federal and provincial tax incentives.In large part, these incentives ~ special credits or reduction in tax for carrying out specific exploration, processing or other activities - have helped to moderate the adverse effects of the higher tax rates and have provided inducements for exploration and processing activities which might not otherwise have been undertaken.However, the effectiveness of certain of these incentives can be questioned: our over-all tax structure now consists in large part of punitively high marginal rates with some extraordinarily generous but capricious tax reductions for specific activities and may not be in the best long-term interest of either the industry or the nation.A rational tax structure, with moderate and stable tax rates, together with reasonable incentives confined to activities specifically requiring them, could be a more effective spur to investment than the present tax and incentive jungleIntroductionIN THE YEARS since federal tax reform, the mining industry in Canada has faced a continued escalation in its tax burdens as federal and provincial governments have leapfrogged each other in imposing new and higher taxes on the industry. The result has been that marginal tax rates imposed on mining and processing activities throughout Canada have jumped to hitherto unparalleled levels."

Jan 1, 1977

"INTRODUCTIONThe Department of Energy, Mines and Resources has recently developed two automatic controls for use in the cyanidation circuits of Canadian gold mills. These controls are the alkalinity probe and the Continuous Cyanide Titrator both of which are discussed in the paper ""Instrumentation in the Cyanide Process"".(1)In May 1966 these process controls and associated recording equipment were installed in the Bralorne mill by two Scientific Officers from the Department. The object was to determine if the equipment was amenable and applicable to this particular circuit. The purpose of this paper is to discuss the performance of the equipment over a test period of 4 months.CONCLUSIONSThe results of test work to date indicates that both the Conductivity Probe and the Continuous Cyanide Titrator would be an as set to the operation of the Bralorne mill.The conclusions are generalized as follows:-(1) At a milling rate of 100, 000 tons per year the expected reductionin reagent consumption would give a direct saving of 37, 660 lbs of lime@$0.030 per lb and 15, 790 lbs of sodium cyanide@ $0.175 per lb. Such cost savings would pay for the equipment and installation costs within a 30 month period"

Jan 1, 1967

By Laxman M. Amaratunga

Laboratocy flarmnability tests were perfonned on dust samples from Fraser Mine in a 1.2 L Lindenburg horizontal tube furnace to detennine the percentage of sulphur oxidized during ignition. The explosion pot ential of sulphide dusts depends on their degree of spontaneous oxidat ion, which was measured by the quantitative analysis of so2 gas released during ignition. Test results indicated that dusts with low sulphur content could exhibit a higher degree of oxidation than a sample with high sulphur content. txlst characterisation using image analysis techniques suggests that the structure and the texture of dust are important factors influencing the explosibility of sulphide dust at ignition temperatures. Therefore for safe mine operations% sulphur content cannot be considered as a reliable single index that could be used to predict the potential of a sulphide dust explosion. Physical, chemical and mineralogical characterisation of dust plays an important role in the detennination of suitable indices for the prediction and prevention of sulphide ore dust explosions.

May 11, 1988

This work illustrates the potential of two welding processes for joining AA1100-16 vol.% B4C metal matrix composite: laser welding process using a 4 kW Nd:YAG laser and Friction Stir Welding. A comparison is made between these two welding techniques in terms of microstructure and mechanical properties of welded joints. A large amount of brittle needle-like phases, together with some residues of B4C particles were observed in the fusion zone of laser welded joints. The use of Ti filler can improve the microstructure and increase the joint efficiency from 63% to 75%. On the other hand, the friction stir welding process being a solid state welding technique is interesting as it avoids the formation of brittle intermetallic phases. In addition, the breakage of B4C particles and the grain refinement of the matrix were observed in the weld zone. Consequently, FSW joints show much better mechanical properties than laser welded joints. Up to 100% joint efficiency can be achieved by FSW for annealed AA1100-16 vol.% B4C materials.

Jan 1, 2011

By Ngonidzashe Chimwani, David Glasser, Diane Hildebrandt

"Milling circuits play an important role in achieving the desired product; tonnage, size distribution and properties, since they are directly linked to the comminution energy consumption for the whole process. A grinding model with a mathematical simulation was developed for an open milling circuit with a scalped feed from a hydro-cyclone. The circuit was optimized by determining the optimal conditions in terms of energy consumption which would produce a floatable product having a desired size range (i.e. -75 +9 µm) for a platinum-bearing ore. The simulation results showed an operating region comprising the best combination of the ball filling and mill speed to achieve the highest production of a floatable size class, with the minimum energy consumption.INTRODUCTIONBall milling is usually conducted in closed circuits in order to achieve a desired product size without material overgrinding. The technological importance of optimising milling circuits cannot be overemphasised (Toneva and Peukert, 2007). Previous work has brought significant insights into the benefits of modelling milling circuits (Austin et al., 1984; King, 2012; Toneva and Peukert, 2007). However, the ability to model these circuits is dependent on the performance of the classifiers and the fidelity of the grinding mill model used compared to the actual circuit (Toneva and Peukert, 2007). Austin et al. (1984) identified five types of milling circuits as shown in Figure 1 namely; the grinding circuits employing mill in an open circuit, normal closed circuit, reverse closed circuit, open circuit with scalped feed, and, the combined closed circuit. Depending on the presence of the first classifier, the second, or both as well as their corresponding loops (streams), the combined circuit (e) can reduce to; an open (d), a normal closed (b), an open circuit with scalped feed (c) or a reverse closed circuit (a). In the case of an open circuit, the mill is operated without being directly influenced by a classifier. The normal closed circuit does not have the first classifier and therefore the make-up feed is the actual feed stream. Conversely, the reverse closed circuit keeps only the first classifier. The open circuited with scalped feed has only the first classifier but does not have the second one. The overflow stream from the classifier is mixed with the mill product to form the final product for the downstream process."

Jan 1, 2016

By G. R. Haiden, E. Henderson

"An LHD teleoperation and guidance system, developed at the Ontario Division of Inco Limited, has been demonstrated in operation at Copper Cliff North Mine (CCNM) since late September, 1993. The tests performed to date have evaluated the feasibility and production viability of multiple LHD operation, from surface by one operator.The systems technology required to accomplish this consists of an electronic monitoring and control package mounted on the LHD; a high bandwidth mining computer network capable of providing radio frequency coverage; and an operator control console which provides an operator workstation for multiple LHD operation.This paper discusses the systems required to accomplish the task of LHD teleoperation and guidance, the benefits of multiple machine operation and future research and development directions. IntroductionSince underground mining began, persolU1el have entered the mine workings to mine ore. Today, however, the rapid advancement of modem telecommunications, computer hardware and software technology has opened the door to remote mining technology that was considered unfeasible a few years ago. This paper discusses the ingredients of remote mining technology that have been developed at Inco Limited.Figure I represents an historical view of the application of electronics to LHD operation at Inco Limited. In 1980, the first radio remote controls for the operation of LI-IDs in large open stopes were tested. The successful application of this technology at Inco went hand-in-hand with the development and application of the Vertical Crater Retreat mining method. The combination of these two advances had a very positive effect on the productivity in the mid-eighties at Inco. In 1991, the Mines Research Department of the Ontario Division advanced remote control technology by developing a high capacity underground mining telecommunications system. This system is capable of moving voice, data and video information throughout the mine workings. The system is based on broadband communication technology found in most automated factories, with the added benefit of providing the information to and from mobile equipment through radio interfaces. The first test of the system consisted of an operator teleoperating a single LHD (on the 3000 ft level) from the surface. The next test on September 13, 1993, demonstrated the first production application of multiple LHDs being run from surface with a single operator."

Jan 1, 1994

By M. J. Brodie

"The decision to proceed with mine decommissioning, generally involves a number of complex and independent factors. These factors, including potential for re-opening, legal requirements, contingent liability, asset depreciation, due diligence, and public relations are discussed in the context of the financial implications on a net-present- value basis. It is concluded that the decision to delay mine decommissioning is commonly not in the best financial interests of the mine operator. Some measures to reduce decommissioning costs and expedite the process are presented.IntroductionThe primary audience for this paper is mining executives, although it should be of interest to all professionals involved in the planning and carrying out of mine decommissioning. Historically, mines were abandoned, not decommissioned. Then, as decommissioning became required, it was assumed that salvage revenue would pay for decommissioning. During the I980s, it became apparent that mine decommissioning costs would exceed salvage revenue for nearly all sites, and that a substantial net cost for decommissioning would be realized for some sites. Throughout this period, the approach to decommissioning has evolved through the sequential addition of measures to meet the increasing regulatory burden. This has resulted in a process in which the elements of decommissioning may not be optimized with respect to each other for the most favourable net present value to the corporation. Additional considerations which are not specific to mine decommissioning, such as environmental policy, due diligence and public relations, may now come to bear on the decision-making process.This paper addresses the issue of mine decommissioning as a three-step process. The first step involves identification and evaluation of all of the issues that relate to mine closure, the most importantof which is the potential for re-opening of a mine. Assuming that it is decided that a mine is unlikely to re-open, the second step is to determine when to carry out the decommissioning work. This aspect is examined through a net present value (NPV) approach. Finally, details regarding who does the work and how the various tasks are divided up must be resolved.Every mine is a unique concentration of minerals at some specific location, hence the development, operation and closure of a given mine must be regarded as a special case. Superimposed on the site-specific considerations are the size, history and financial status of the associated corporation."

Jan 1, 1995

By Charles Camsell

If it were necessary to preface a discussion of the mineral position of the Empire by justifying one's interest in that subject, there are two points that at once suggest themselves by way of vindication. Tremendous Growth of MINERAL Consumption The first of these points has to do with the general question of the world's mineral consumption. Most thinking persons appreciate in a more or less vague way the vital rôle that has been, and is being, played by mineral products in building up the material side of our modern civilization. But, apart from that casual and almost subconscious appreciation, very few have any precise knowledge of the extent to which the growth and the operation of our vast present-day industrial structure has been made possible by, and only by, a tremendous increase in the consumption of mineral products of all kinds. The increasing use of minerals confronts us today at almost every turn. It does not matter in what direction we look-at the expansion and the change in transportation facilities, in the air as well as on land and on sea; at the increasing mechanization, not only in factory and mill but even in our domestic life; or at the constantly widening use of machinery for all phases of farm production-everywhere we meet the same phenomena of rapidly growing uses of equipment produced mainly from minerals. Without resorting to any tiresome statistics, a few figures may suffice to indicate with what enormous strides the world's mineral consumption has been advancing. The figures for recent years may be open to objection on the plea that, ever since the outbreak of the world war, conditions have hardly been sufficiently normal to give us trustworthy data-we have been living under extremes either of depression or of abnormal stimulation. During the last decade before the war, however, from 1903 to 1913, the world was moving along in a quietly prosperous manner; and we have figures, or at least reasonably reliable estimates, as to the growth in mineral consumption during that decade.

Jan 1, 1932

By Robert B. Parsons

"New Brunswick Finance Minister John Baxter pulled something out of a hat for the mining industry in April, but there is a general concensus in the industry that he should put II back where it came from.The industry has never been in the mood f or progressive rate structures, but that is exactly what New Brunswick 's 1984 budget offers to this depressed sector of the economy.IntroductionThe Province of New Brunswick stunned the Canadian mining community in April with the announcement that the province' s 16% mining tax rate would be replaced with a progressive rate structure effective January 1, 1984 (Table I). The proposed change, contained in the bud get papers tabled by Finance Minister John Baxter on April 17, caught the industry totally by surprise. The move to a progressive rate structure was completely unexpected for a variety of reasons:• Generally speaking, relations between the province and the industry have been relatively good, yet the industry was apparently not consulted with respect to the proposed measure and had no indication that a change of th is nature was coming. This is in stark contrast to the mood which prevailed during the major revamping of the province' s mining tax regime in 1977: at that time, the industry was invited to contribute in advance to the province's plan for a new tax structure.• The new structure would appear to make th e province less competitive in terms of mining tax rates with Ontario , Quebec, and other provinces, despite indications in the past that New Brunswick is very cognizant of this competitive factor in formulating mineral policy.• A joint report in November 1978 by federal and provincial officials to federal and provincial finance and resource ministers, which was careful not to directly criticize Ontario and Quebec's progressive mining tax rate structures, recommended that provincial "" tax regimes be examined to ensure the inclusion of appropriate mechanisms to avoid the excessive taxation of cyclical type profit "" , and that ""the federal and provincial governments consider the concern over progressive tax regimes expressed by the industry and examine mining and royalty tax regimes and the income tax regime with a view to alleviating the effect of such regime on the aggregate marginal tax rate"". In this context, any move to a progressive rate structure would be viewed by many observers as retrograde."

Jan 1, 1984

By F. Hassani, E. Aflaki, M. Nokken, M. Kermani

"This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill consists of tailings, different binders such as Portland cement, fly ash and blast furnace slag and an alkali activator such as sodium silicate. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. The influence of sodium silicate concentration, pulp density and mixing time on the mechanical properties of samples were evaluated using the uniaxial strength test. Mercury intrusion porosimetery (MIP) was used to analyse the microstructure of CHF and Gelfill samples.This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Mixing time strongly influences the mechanical properties of Gelfill samples but did not have any effect on CHF samples. (iv) The MIP analyses indicate that the pore size distribution and total porosity of Gelfill and CHF were different, and this did contribute to higher strength development of the Gelfill samples. INTRODUCTIONThe increased depths of mines in the Canadian Shield and the high stress associated with these depths favour a new method of mine backfill that can both meet strength requirements and help mine productivity. The mine backfill mainly consists of tailings, water and binder materials, the latter being most expensive. Gelfill is a new mine backfill material whose binder usually consists of alkali activators such as sodium silicate and other cementitious materials such as blast furnace slag and normal Portland cement. Although sodium silicate has been used in concrete manufacture, the use of this material in mine backfill is relatively new (Doucet, 2007, Razavi, 2007). Until very recently there have been only a few isolated publications, mostly out of McGill University, regarding mine Gelfill (Razavi, 2007 and Kermani et al., 2009 and 2010). These papers have investigated some of the basic mechanical properties and mechanical behaviour of Gelfill. However, the physical performance of Gelfill in various conditions has yet to be understood. Therefore, the main objective of this study was to investigate the influence of mixing time and sodium silicate concentration on the mechanical performance of Gelfill and CHF through a series of experiments. Moreover, the microstructure of the Gelfill and CHF samples was studied."

Jan 1, 2015

By D. Chadwick, J. W. Matousek

Between 1860 and 1890 -- from the time of the American Civil War to the last decade of the 19th Century -- nickel production in North America was dominated (even monopolized) by the output of the industrial complex of the Gap Nickel Mine near Lancaster, Pennsylvania and the American Nickel Works in Camden, New Jersey. In some years, from one sixth to one third of the world's metallic nickel supply came from this enterprise. Mining and smelting were conducted at Lancaster; a matte of high iron content was shipped to Camden for pyrometallurgical and hydrometallurgical refining to produce nickel metal, copper sulfate, and cobalt oxide. The high purity nickel product was rolled into sheet for marketing, primarily for coinage, as nickel had few other uses at that time. The undertaking experienced all of the problems that face the mining and metallurgical industries of today: declining reserves, high labor and fuel costs, high transportation costs, fluctuating demand and prices, pollution concerns, and foreign competition. The technical features of the geology; the mining, smelting, and refining operations; and some of the economic aspects are assessed. The view is taken from that of the present time -- seeking those lessons from history that we are supposed to learn or face the prospect of repeating the mistakes of the past.

Jan 1, 2005

By Gordon Thompson

"Development of the unique Mine Games exhibition at Science World British Columbia is the largest ever collaboration of many interests to present the story of mining and the issues of mineral development delivered to the public by a science education centre.IntroductionMineral education programs have long been a major focus of the British Columbia mining community. Mine Games and its tremendous potential to enhance industries image and the public's awareness of mining is unequalled in the field of Issue Based Education Exhibits.The main goal of the exhibition is to look at the future of resource industries in a rapidly changing world of economic activities, new technologies, and growing public concern for the environment. Three challenges were the aim of the exhibition: to increase participation, to serve as a tool to increase interest in science and technology, and to draw an increasing number of school students to the interests of geology and the earth sciences. Mine Games is to serve as a meeting place for discussion of issues and where reliable information can be shared and new ideas explored.The exhibition is designed to develop new approaches to hands on learning that encourages visitors to explore and generate discussion and thinking with respect to resource development activities.The role of author, beginning in 1993, was, with senior industry leaders, to coordinate the raising of $1.3 million to complete the funding of the $1.6 million project total. The second and most interesting challenge was to work with the many minds that were collaborating to create the exhibition and to assure that the facts and science were correct. This involved the coordination of ""expert groups"" that verified the science and technology and the issues that the creative design team at Science World planned to use in development of each exhibit module."

Jan 1, 1995

By D. Berkley

Off-gas systems often become the limiting factor in production increase and environmental projects. Any upgrade or new off-gas project needs to address control instability issues, instabilities that can result in safety hazards, significant loss of system capacity and/or emissions to the environment [1]. In addition, the design engineer must optimize system configuration and equipment size for the new operating conditions, to have a technically feasible and economically viable project. Dynamic simulations can be used for addressing both the control stability and the design optimization issues. This paper illustrates how the dynamic simulation of transient processes and of their control system can be used in "real life" situations for these purposes, presenting the example of an electric furnace off-gas system design.

Jan 1, 2005

By T. Sugawara, S. Hara, Y. Mitsui

Surfaces of rock slopes in cold regions often become frozen in winter. Therefore, understanding time-dependent behavior of frozen rock, as well as that of unfrozen rock, is important for long-term stability assessment of rock slopes. In this study, a series of uniaxial compression tests and creep tests were carried out on Shikotsu welded tuff under dry and water-saturated conditions at -20 °C to clarify timedependent strength and deformation of the frozen rock. The influence of water content on them also was investigated. It was found that the amount of deformation of the water-saturated specimen was much greater than that of the dry specimen. It also was found that the creep behavior of the water-saturated specimen was similar to that of polycrystalline ice. These show that deformation of the water-saturated specimen is strongly affected by pore ice. The UCS of the water-saturated specimen was approximately equal to that of the dry specimen at a strain rate below 4.2×10-6/s, and its value was about 17 MPa. However, the former increased up to 26 MPa at 4.2×10-4/s with loading rate, whereas there was little increase in the latter. This means that the UCS of the water-saturated specimen was always greater than that of the dry specimen at higher strain rates. The creep life of water-saturated specimens was longer than that of the dry specimens at stress level greater than 15 MPa. These results of UCS and creep life show that inclusion effect due to presence of pore ice plays an important role on strength of the water-saturated specimen. Creep life of the non-failure specimen that was loaded for more than three days was estimated by the relationship between creep life and axial strain rate at 10 s on failure specimens. It was found that creep life of the water-saturated specimens was shorter than that of the dry specimen at stress levels less than 14 MPa. This suggests that estimation of creep life of frozen rock under water-saturated condition is important for the stability assessment of frozen rock slopes. It was clear that the loading-rate dependency of UCS was related to the stress-level dependency of creep life in both dry and wet conditions. This indicates that there are common fracture mechanism in creep and uniaxial compression tests. It also indicates that the creep life can be estimated by the relationship between the UCS and the loading rate. The time dependencies of the water-saturated specimen were in good agreement with those of polycrystalline ice. This confirms that pore ice strongly affects the strength of the water-saturated specimens as, well as the deformation behavior.

Jan 1, 2015

By G. A. Vissac

In this paper we intend to deal particularly with the economic side of coal washing as it applies to our mines. We will then discuss why the dry-cleaning process has been selected, and give a brief description of our plant, dwelling only on its specific features and referring the reader to the numerous papers published on the subject for any details on the principles and machinery used in dry cleaning. ECONOMIC DISCUSSION The washery introduces an extra cost for depreciation, operation, and loss in treatment. A certain proportion of the coal, now being sold, and which the miners have been paid for. will have to be wasted. As a whole, the total increase in cost would be approximately 60 cents per ton. On the possibility of recovering this amount depends the success of the washery. There are two advantages to be expected from the washery, the first, which occurs at the mine and which will be certain; the second, more difficult to estimate, because it depends upon convincing our customers that they should pay more for a better product.

Jan 1, 1924