Search Documents

By Carmen M. Neculita

Optimizing the long-term efficiency of passive systems for the treatment of highly contaminated acid mine drainage (AMD) is still a challenging issue. The optimization lies, among others, on improving the understanding and quantification of metal removal mechanisms in order to predict and enhance the stability of neo-formed minerals in secondary phases. Sorption, and precipitation as oxides-hydroxides, carbonates and bio-sulfides are likely the most important metal removal mechanisms involved in passive biotreatment of both slightly and highly contaminated AMD. In the same time, the preferred mechanism is precipitation of metal sulfides that are more stable and less pH dependent than carbonates and oxides-hydroxides. However, results of relatively recent research studies performed at laboratory scale showed that sulfides accounted only for up to 15% of total metals removed in passive bioreactors treating highly contaminated AMD dominated by iron (around 500 mg/L). Several approaches were used in the aforementioned studies to understand and quantify metal removal mechanisms in spent reactive mixtures collected from long-term (12-15 months) operating column bioreactors. These included: thermodynamic equilibrium modeling and various chemical extractions and mineralogical analyses (such as single and sequential extractions, acid volatile sulfides-simultaneously extracted metals determination, scanning electron microscopy, X-ray diffraction, and thermo-gravimetric analysis). The large proportion of metals (85%) removed by sorption and precipitation as oxides-hydroxides and carbonates suggests a relatively high mobility of the neoformed minerals, especially in low pH conditions. However, no data is available on the long-term stability of spent reactive mixtures and, on the implications for the sustainable management of this type of solid waste. Lately there is almost a consensus that the efficiency of highly contaminated AMD treatment is warranted by the use of multi-step passive systems, including both chemical and biological units, installed sequentially. However, very few well-documented studies are available on the design, construction, operation and long-term efficiency of these multi-step systems. A leading example is the tri-unit passive system installed on the abandoned Lorraine mine site (Québec) to treat a highly contaminated AMD dominated by iron (about 2,500 mg/L). This tri-step system (160 m3), consisting in two bioreactors separated by a unit filled with wood ashes, achieves to date a satisfactory removal of iron (up to 99%). Moreover, based on the data collected during laboratory testing, iron was mainly removed in the wood ashes unit (from around 3,200 mg/L to 10 mg/L) by precipitation of oxides-hydroxides as predominant mechanism and only partially by sorption. However, no data is available on the actual metal removal mechanisms in the field. Overall, theses multi-step systems are more complex and their long-term performance is even less predictable than the single unit systems. This paper presents the current knowledge and the research needs on metal removal mechanisms in passive bioreactors and multi-step systems for the long-term treatment of highly contaminated AMD. KEYWORDS

Aug 1, 2013

By Andrew Bamber

The mining and beneficiation of minerals is the second largest end-use of electrical power on the planet, and comminution is by far the largest single contributor to this. Several jurisdictions, including British Columbia, have, in response to concerns about greenhouse gas emissions and climate change, adopted energy conservation legislation, including carbon taxes, carbon trading and conservation incentive schemes. Key to achieving conservation objectives is firstly an understanding of usage metrics across the various unit operations in the sector, and secondly an understanding of the conservation potential represented by available technologies and approaches in reducing end-use. This paper presents the results of a recent utility-funded study on energy use metrics and conservation potential at large open pit mines which are typical of the sector in BC.

Aug 1, 2013

By R. O. Grieve

"IntroductionCALEY (1945) and Evans (1950) pointed out that certain instances of convergence between Devonian and Silurian horizons, frequently evident in wells drilled for oil and gas in Ontario, appear to be related to local thinning of salt beds in the Salina formation and they suggested that leaching of the salt beds may have occurred. Exploratory drilling by Imperial Oil Limited since 1945 has brought to light several examples of structures similar to those discussed by Caley and Evans. The writer has had the opportunity to examine cuttings and data from wells which penetrated these structures and the attempt to interpret them in the light of the theory of leaching and subsidence proposed by Landes ( 1945a) to explain the marked brecciation and deformation of Upper Silurian and Middle Devonian sediments which crop out in the Mackinac Straits region of northern Michigan has led to the observations presented in this paper."

Jan 1, 1955

By R. A. L. Drew, G. Mendoza-Suarez, J. Filipi, R. Vintila, J. A. Kozinski

Economics and environmental considerations along with the increasing demand of hydrogen encourage development of novel technologies such as plasma processing of hydrocarbons and thermal cracking of natural gas. Plasma discharges, either in thermal or non-thermal regimes are expected to allow low temperature and fuel flexible on-site hydrogen generation. The main drawback of thermal plasma reformers is the high-energy consumption resulting from high-temperature operation. On the other hand, non-thermal plasma, generated by dielectric barrier discharge (DBD), is able to simulate the chemical reactions employing much lower energies than those required by thermal treatment processes. The non-thermal plasma process allows for instance, a direct conversion of methane into hydrogen and carbon black with no CO2 release. The focus of this research was on the GHG-free method of H2 generation in compact non-thermal plasma reactors using low, medium and high permittivity dielectric ceramics. A stable, non-thermal plasma was generated by placing a dielectric ceramic between two electrodes with a 25 thou gap and applying an alternating current of 1-5kHz and voltages of 4-8kV. In order to ensure energetic efficient plasmas, experiments were conducted to analyze the behaviour of different permittivity ceramics. It was found that the dielectric properties of a ceramic, when used in a DBD reactor, have a strong influence on the discharge characteristics, which in turn influence the power consumption. Higher dielectric constant resulted in higher conversion rates of methane (higher yield of hydrogen and carbon). At the same time, the mechanical properties of the dielectric material, which are closely associated with its processability, influenced its resistance to electron bombardment, as well as thermal and mechanical damage. Therefore a reliable ceramic should have good dielectric properties, in addition to good thermo-mechanical stability.

Jan 1, 2004

By Jean-Pierre Birat, François Hanrot, Gérard Danloy

Global warming presents an enormous challenge to the steel industry, which is both carbon-intensive and energy efficient. Lean production can provide some short-term emission mitigation, at the level of the Kyoto requirements. In the middle term, more use of scrap will also help alleviate emissions. But to reach much larger reductions in GHG emissions, on a par with the likely targets that will be set after the Kyoto period, the steel industry will have to imagine new production paradigms, which constitutes its most formidable challenge for the years to come. Carbon capture and sequestration, processes leaner in carbon use, electricity and hydrogen from green sources will have to be added together in a patchwork of process routes, which will have to be developed at great risk in the next decade, hopefully through broad international cooperation.

Jan 1, 2004

By J. N. Van der Merwe, M. Mathey

"The development and mechanical characterization of coal-crete, a composite material generated from coal fragments and some binder material, is described in this paper. Coal debris was obtained from a colliery in South Africa. The binder used in the study basically consists of cement and water, and further ingredients are added to the mixtures, such as sand, fly ash and polymers, in order to investigate alterations of the mechanical properties of coal-crete.Results from over 220 mechanical tests on coal-cretes with various binder mixtures give consistent trends for the material’s behaviour. Linear relationships are suggested between the uniaxial compressive strength, Young’s Modulus and the indirect tensile strength of the coal-crete.It is shown that mechanical properties comparable to coal can be achieved. Coal-crete is therefore suitable for physical modelling of mining situations in experimental studies and for use as backfill in underground coal mines. The latter application is particularly attractive when refuse coal is used as aggregate material. The indicated trends in this study may be used as a guideline for individual coal-crete design needs. However, some uncertainty remains as to the influence of particle shape, size and gradation, coal rank and age of the coal-crete. These aspects are recommended for further research."

Jan 1, 2015

By B. Nanthakumar

The impact of stockpile oxidation on chalcopyrite was studied through collectorless and collector-induced flotation conditions. In both cases, the Cu grade-recovery performance of stockpiled ore showed relatively poor concentrate grades with respect to that of a fresh sample. However, the oxidation had a minor effect on chalcopyrite recovery itself. The poor concentrate grades resulted from dilution effect primarily by excessive flotation of pyrrhotite. Size-by-size analyses indicated that for the collectorless flotation, the recoveries in the coarse and fine particle-size regions, were higher for fresh ore than for stockpile sample. A greater impact was seen in the coarse size regions for both types of sample, compared to the collector-induced case. The Cu recoveries showed a remarkable increase in the coarse size range for both samples when a collector was used. However, the case for stockpile sample was a marginally higher compared to the fresh sample. This difference has been offset by an opposite trend that was observed between these two samples in the fine size region. It is concluded that in contrast to the case with nickel-bearing sulphides, stockpiling conditions do not show a significant adverse effect on behaviour of chalcopyrite due to its strong floatability, regardless of oxidation.

Jan 1, 2007

By Rodrigo Craig Cerello

The Brazilian economy has always presented a strong correlation with the mineral activity. Since colonization days, due to the territorial expansion caused by the explorers search for gold, mining in Brazil became a basic sector of national economy. Currently, the Brazilian mineral sector¹ estimates a 550% production increment (Figure 1A) in the last 10 years, reaching the US$ 50 billion value, reflecting the increased global demand for raw materials from mineral origin. According to the Brazilian Constitution², mineral resources belong to the Federal State and, consequently, their exploitation must be authorized, under penalty of engendering federal crime. Furthermore, activities of this nature are prone to cause environmental degradation such as, but not limited to, deforestation, pollution, soil deterioration and water contamination. The GPEMA represents the forensics group of the Brazilian Federal Police responsible for the technical analysis of traces related to crimes against the environment and consequently, illegal mining cases.

Aug 1, 2013

By H. J. McQueen

Before 1950, hot working was simply deforming above the recrystallization point and gave a soft product compared to cold working. From 1960 onwards, improved testing in compression and torsion (stress, strain rate, temperature, quenching) provided valid specimens for microstructural analysis by polarized optical and transmission electron microscopy (TEM). Indeed, TEM was essential to uncovering the hot working mechanisms because it could distinguish between cold and hot substructures (dynamic recovery) in either initial or new grains (dynamic recrystallization). Over the years, teams at Concordia, McGill and UBC obtained NSERC support for students and equipment. CANMET built up a hot forming group having capabilities from high-rate cam-plastometer compression to rolling of experimental alloy billets; this was combined with latest metallographic instruments for fundamental research. Al alloys of every class (2000, 3000, 5000, 7000, 8000) were studied to understand the effects of solutes, precipitates, dispersoids and composites. The complex flow patterns in extrusion were clarified and modeled by finite element methods. Physical simulations of rolling schedules (up to 20 passes and reductions of 98%) by torsion provided evidence of microstructure development during both the passes and the softening intervals, thus clarifying development of texture in different alloys. The results frequently appeared in proceedings of Light Metals symposia and Canadian Metallurgical Quarterly

Jan 1, 2011

By Louis Frost

MINE ventilation has for many years been the subject of intensive study by numerous investigators who have presented their findings in forms that are understandable to the average mining man, and all this writer hopes to do is to review those findings in relation to the 'manager's' problem in mine ventilation. It would not, perhaps, be wholly correct to acclaim practical mine ventilation as an exact science, because of the many variables entering into the problem. Each mine has its own particular problem and ventilation characteristics. Fan design, in contra distinction to mine ventilation, is an exact science, but the designer cannot always take into proper consideration the practical variations to which each mine is subject. Fan designers, accordingly, are forced to base their design on such data as the mine manager or engineer is able to supply, and, when it is borne in mind that the mine characteristic is constantly changing, it is not at all surprising that fans do not always show efficiencies hoped for. In many instances, fans work far beyond the de-signer's limitations, and, in consequence, are an economic disability in the colliery cost-sheet, and it is of paramount importance that the colliery manager evaluate all the factors involved in relation to fan performance for the colliery to receive full benefit from its investment.

Jan 1, 1941

By J. Bednar, R. R. Rogers, W. Dingley

"Zinc is by far the most important metal used for protecting steel from the ravages of corrosion, and cadmium is also used extensively for this purpose. These metals are applied by electrodeposition in cyanide baths when a particularly good appearance and high throwing power are required. One great disadvantage in using these baths has been the decrease in cyanide concentration and the increase in carbonate concentration that takes place during the plating. Another disadvantage has been the development of serious embrittlement in high-strength steels. The present authors have developed new cyanide baths for electroplating both zinc and cadmium on steel. These baths are stable in composition during plating, they have not produced appreciable embrittlement in the high-strength steels that have been investigated up to the present time, and they permit the use of considerably higher plating current densities. In addition, they produce extremely fine grained coatings that are attractive and have excellent adherence and covering properties. Brighteners can be used in the plating baths if bright finishes are required."

Jan 1, 1967

Roasting of molybdenite concentrate is an important stage in the production of commercial molybdenum trioxide. The oxidation kinetic and mechanism of molybdenum sulfide concentrates from two plants were investigated at temperatures from 444 °C to 640°C. The rate of reaction was determined for thin layer samples in a muffle furnace at controlled temperatures, oxygen excess and removal of sulfur dioxide. For both concentrates the rate of reaction is fairly slow at temperatures below 500°C and remains fairly constant from 540 to 600 °C. It was observed that the concentrate from the first plant presents a tendency for sintering or glazing at temperatures above 620°C, whereas the same phenomena was observed at 20 or 30 °C higher temperature for the second concentrate. A kinetic model of two reactions, involving the formation of Mo02 as intermediate oxide for the production of Mo03 is proposed and activation energies of 23.0 and 20.8 kJ/mol for the first and second reaction were calculated for temperatures between 520 °C to 600 °C. These low values of activation energies indicate that the overall rate of oxidation is controlled by mass transfer, particularly in a porous layer of oxides. Therefore, the renewal of the surface by mixing and motion of the concentrate layer is of great importance. Sublimation of Mo03 becomes significant for temperatures above 650 °C.

Jan 1, 2007

By S. J. van Rensburg

Competition for resources, including water and arable land, refocused attention on water and gold tailings management with respect to quantity and quality. MINTEK established and validated an "Advanced Leach Facility" to record kinetic leach information aimed at gold refractory sulphide ores. This facility was developed because of the need for additional leach process information to enable proactive decision making. Instead of focussing on optimised gold recovery only, the impacts of pre-oxidation methodologies were evaluated by considering key parameters, including cyanide speciation, reagent consumption, thiocyanate, arsenic, heavy metals, salt loads, water quality and residue stability. Results from oxidative leaching of a refractory gold ore employing oxygen, ozone, ultra-fine grinding, high shear and pressure oxidation are discussed. The relative cyanide and lime costs and environmental and sustainability effects associated with these technologies are briefly outlined.

Jan 1, 2011

By Lar Liljeblad

"As demands upon the earth's natural resources continue to grow, exploration companies, mining organizations and others face the problem of the need to tackle increasingly more difficult strata to open up new reserves. Innovations in materials technology and tool design have steadily improved this capability, but none perhaps so drastically as a recently introduced cemented carbide in which tool wear resistance and/or toughness can be tailored precisely to the user's drilling needs.Introduction Until about forty years ago, the bulk of rock-drilling operations had to be carried out with hardened steels. Short life between re-grinds was common especially in abrasive rock formations. Shortly after World War II, Sandvik, Sweden, pioneered the development of sintered (cemented) carbide-tipped steel tools as a means of improving drill tool life. The new material was a composite of tungsten carbide and cobalt, the latter acting as a 'cement' to bind the wear-resistant carbide grains together, and the composite, in turn, was brazed to the steel. The immediate effect was a 100-fold increase in the service life of the tool.Intractable ProblemsWhile the carbide-tipped tools served the mining and quarrying industries admirably there were, nonetheless, some seemingly intractable limitations. The greater the wear resistance of the material - the quality for which it is selected - the more brittle it is. Also, rocks vary widely in hardness and abrasiveness and no single tool, either in terms of material or shape, meets every need. Specifically, for fast penetration of non-abrasive rock, toughness must be combined with a relatively sharp tool prome. Highly abrasive rock, on the other hand, demands a substantially broad area of extremely wear-resistant material on the tool if long bit life is to be assured. Between these extremes there are innumerable variations in rock"

Jan 1, 1991

By Klau Meyer

"At Teck-Corona Operating Corporation's David Bell Mine, a successful water quality management strategy has been established. This resulted from the development and application of process technology, allowing year round discharge of an effluent exceeding the chemical and biological standards set by the Ministry of Environment. This strategy aims at minimizing contaminant levels of effluents through optimization of reagent selection and reduction of effluent volumes through maximizing reclaim water usage. Concentrator and effluent treatment plant operating practices, process chemistry and the results of the water quality management strategy are reviewed.IntroductionThe David Bell Mine is located in the Hemlo gold camp 42 km east of Marathon, Ontario. The concentrator has a design throughput of 1000 tonnes per day. The processing of the run of mine ore ( - 15cm) involves the following unit operations: grinding in a semi-autogenous mill followed by a ball mill, thickening, pre-oxidation , cyanidation, and carbon-in-pulp gold recovery followed by electrowinning and refining.The David Bell Mine water quality management strategy is composed of the following items (Goodfellow and Meyer, 1991):• natural destruction of cyanide contained in the tailing water in a large shallow tailing pond ;• preliminary treatment of reclaim water in the grinding circuit for cyanide and heavy metal removal;• pre-oxidation of sulphide minerals in pipe reactors to reduce cyanide consumption using pure oxygen;• pH control in the grinding, pre-aeration and leach circuits to minimize the dissolution of stibnite while maximizing gold recovery; • close control of cyanide addition rates to the leach circuit to maintain the lowest possible levels;• a carbon column for gold recovery;• an effluent treatment plant for antimony and heavy metal removal; and• the use of final treated effluent for industrial water underground to minimize fresh water consumption."

Jan 1, 1992

Agenda ?Introduction ?Geology ?Mining ?Metallurgy ?Process, Layout ?Environmental Background ?Kinross Gold Corporation owns the Lobo-Marte gold property, located in Region III of northern Chile. ?The property is close to two other Kinross mines, Maricunga 50kmto the south and La Coipa 60km to the north, plus a regional office in Copiapo and district level operating synergies are expected. ?Lobo and Marte were discovered in the early 1980s and are intrusion-hosted, porphyry-type precious metal deposits, typical of the Maricunga District. ?The Marte open pit heap leach mine was in commercial production in late 1988, but was suspended in February 1992 as it did not meet forecasted production levels and recoveries. ?Kinross plans to recover ore from the Lobo and Marte deposits through an open-pit, heap leach47,000tonne per day operation.

May 1, 2010

By W. Dziurzynski, St. Wasilewski, T. Palka, A. Krach

"Air parameter monitoring systems, regardless of gasometrical protections, provide a significant number of measurement data. The obtained data broadens the knowledge on processes taking place in underground workings and shows the relationships and influence of machines and technological processes on the variability of ventilation parameters in the areas of longwalls. Nowadays, computer simulation methods are increasingly used to reproduce the flow of air and methane mixture in the area of longwalls equipped with shearers. The paper presents the results of a research experiment covering a long-term observation of a longwall area during mining with a shearer using sensors from the mine's monitoring system. Data from sensors for methane concentration, pressure and velocity were used and additional ventilation measurements were taken to determine the parameters characterising the air flow in the area. The influence of different machine cycles in the longwall on the changes of air parameters in the area of the longwall was shown. A numerical model of the ventilation area was developed and the computer program VentZroby was used for the calculations, which allows for the simulation of the process of ventilating the area of the active longwall during the extraction of coal with the use of a shearer and haulage of the run-of-mine. Computer simulation of the influence of the shearer's operation and the methane inflow associated with the distribution of the mixture of air and methane was carried out. The results of the simulation were compared with the data recorded by the monitoring system’s sensors during the measurement experiment. Comparison of the recorded methane concentration courses with the results of a computer simulation of the air and methane flow conditions in the mining area showed changes in the gassiness. INTRODUCTION Studies carried out in the Polish and global mining industry show that methane is an obvious factor in limiting mining production due to the loss of continuity in the operation of longwall complexes in hard coal mines under methane emission hazard (Schatzel et al., 2008). In addition, methane hazards have a significant impact on the safety of the operators of machinery in the longwall. The requirements of Polish regulations and the practice of safe operation of mining longwalls require correct determination of gas concentration, volume flow, as well as pressure and temperature of the flowing air. As part of the research undertaken in the Budryk (Wasilewski, 2010) and Bielszowice (Dziurzynski et al., 2009) mines to assess the methane hazard in the longwalls and workings in the vicinity of the longwall, research experiments were carried out, during which air parameters were recorded by the mine monitoring system and additional testing equipment in different cycles of shearer operation."

Jan 1, 2019

By A. B. Parsons, P. G. Howes

"This article discusses how recent changes in the federal and Quebec .income tax laws have contributed to an improved investment climate for mineral exploration in the Province of Quebec. Individual investors who are resident in Quebec and who are in the highest tax bracket (1984-60.4% marginal rate) may obtain tax benefits that result in only nine cents of each invested dollar being at risk.IntroductionIn a recent submission by the Mining Association of Canada to the Royal Commission on the Economic Union, it was stated that the mining industry ""is no longer discovering and opening new mines at rates sufficient to offset the depletion of existing orebodies and to maintain pre sent output"". With world metal prices still in a depressed state following the prolonged 1981-82 recession, moreover, the continuing success of Canadian mining in world markets will depend on this country's ability to compete in a new environment characterized by subsidized Third World production . For the most part, this new competitive environment will encourage the development of cost-efficient mines that are better equipped to withstand the troughs and valleys of international metals prices."

Jan 1, 1984

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By Gerhard Kircbner, Boen Tan

"IntroductionThe Key Lake uranium-nickel ore deposits are located in the Athabasca Basin of northern Saskatchewan, Canada (Fig. 1). Many papers have been published on Key Lake in the past (Dahlkarnp and Tan, 1977; Kirchner and Tan, 1977; Kirchner et al., 1980). Immediately after its incorporation in 1968, Uranerzbergbau GmbH, a German holding company, set up exploration subsidiaries in Australia, the United States and Canada. This account reviews those exciting years starting with the concept to explore the rim of the Athabasca Basin in Saskatchewan, and leading up to the discovery of the deposits in 1975 and 1976.A few summary statements can be made:• The discovery of Key Lake resulted from a very systematic exploration approach and the persistence of Uranerz, the operator. • Cluff Lake and Rabbit Lake had been discovered some seven years before, but it was the discovery of the Key Lake deposits which brought Saskatchewan to the forefront to become Canada's foremost uranium producing province.• The experiences gained at Key Lake, which were subsequently published, triggered the discovery of many other deposits of similar, or even larger, size than Key Lake. The spatial relationship of those deposits to graphitic conductors and hydrothermal alteration zones are presently the most effective indicators for locating new deposits - indicators which were first recognized at Key Lake.• Key Lake is, and will remain for some years to come, the largest producing high-grade uranium mine in the world."

Jan 1, 1994