Search Documents

By P. R. G. Brandão, E. E. Ferreira

The presence of metallic cations in solution will affect the aggregation or dispersion of the fine hematite particles, depending on the type of cation adsorption: either specific or non specific adsorption. In this work, the zeta potential measurements were carried out on a sample of pure hematite as a function of pH and metallic cations concentration (Ca2, Mg2+, Mn2+, K+, Na+ and Al3+). The objective of these studies was to clarify the effect of these metallic cations on the surface chemical properties of pure hematite. The cations K+ and Na+ adsorbed as non-specific species and caused only the reduction on the values of zeta potential (in terms of absolute value) over the entire range of pH values tested. For the Al3+ cation, in the acidic pH range it adsorbed as a specific species and increased the zeta potential values. The cations Ca2+, Mg2+ and Mn2+, adsorbed as a non specific species at pH levels less than 6.0 and caused the reduction of zeta potential due to the compression of the electrical double layer. However, for pH values greater than 6.0, these cations adsorbed as a specific species causing the zeta potential to increase and became more positive as the pH value increased (alkaline). This effect could be due to the adsorption of some hidroxy complex species of these cations, which contributed to the positive charge. The effect of metallic cations (Ca2+, Mg2+ and Al3+ concentration, at pH 4.0, 7.0 and 10, showed the following results: a) at pH 4.0, increasing the concentrations of Ca2+ and Mg2+ resulted in on a small reduction in the value of the zeta potential. At this pH, increasing the concentration of A131 cations caused the zeta potential to increase due to specific adsorption of a negatively charged Al3+ hydroxy complex b) at pH 7 and 10, increasing the concentrations of Ca2+ and Mg2+ caused the zeta potential to change its charge from negative to positive.

Jan 1, 2004

By B. Andreaus

In spite of tremendous efforts in research and development of polymer electrolyte fuel cells (PEFCs), essential properties of the actual catalyst material, supported Pt or Pt-alloy nanoparticles, are not yet well understood. Fundamental understanding of the catalyst structure and the prevailing kinetic mechanisms is, however, of utmost importance for further progress. In the present study, we investigate catalyst activity for CO oxidation from a theoretical point of view. Electrochemical CO oxidation serves as an important test reaction for the study of the fundamental properties of supported Pt nanoparticles. Recent experiments have revealed strong effects of catalyst particle size and supporting material on catalytic activity. It was found, that the activity towards CO oxidation decreases significantly when the particle diameter drops below 2.5 nm. We perform kinetic Monte Carlo simulations of CO oxidation on supported catalyst particles to elucidate this particle-size effect. The simulations are based on the active site concept, highlighting the role of active site formation and finite surface mobility of adsorbed electroactive species for catalyst activity. For comparison with experimental results, potential step experiments were simulated. The Monte Carlo simulations consistently reproduce effects of particle size and electrode potential found experimentally. In comparison with our simulations, analytical mean field models and nucleation and growth models exhibit inferior agreement with experimental data. In summary, our findings support an oxidation mechanism via active site formation. The reason for the slow reaction kinetics on catalyst particles with diameters below 2.5 nm is a rather low CO surface diffusivity. The rates of active site formation, diffusion and CO oxidation via recombination with adsorbed OH can be determined from the simulations.

Jan 1, 2005

By S. J. Cook

Outstanding advances among the metals, marked the mineral production records for Canada during the first half of 1925. Production of metals and non-metals reached a total value of $90,347,698. as compared with $84,307,385. in the first half of 1924, an increase of 7.16 per cent. Metals and non-metals produced during the calendar year 1924 were valued at $17 4,202,537.; production during the first half of 1925 showed a sum equal to 51.86 per cent of this total. Advances among the metals were general. Gold rose to a new record. Lead advanced 62.41 per cent over the high mark attained in the first half of 1924. Nickel production was well maintained. Copper was up a million pounds. Silver showed increased values. Zinc followed the trend in lead to almost double the output recorded in the first half of 1924. Cobalt production continued to improve. Despite the loss due to the protracted strike in the Nova Scotia coal mines which reduced the output of coal in that province; during the six months ending June, to less than half the tonnage reported in the first six months of 1924, improved conditions throughout the rest of the non-metal mining field resulted in the production of non-metals during the half-year reaching a total value of $31,199,233. as compared with $36,844,286. in the first half of 1924; the loss in the value of coal output al one amounted to $5,723,873, while the decrease in the aggregate value of non-metals amounted to only $5,645,053.

Jan 1, 1925

By J. P. Mogan, E. D. Dainty, K. Katsuyama

"The Volvo BM 861 U articulated truck is one of the few underground diesel units manufactured by an organization which shares the same corporate roof as the engine manufacturer. As a consequence, the unit has provided an opportunity for the characteristics of the entire system- turbocharged aftercooled engine, transmission and exhaust scrubber- to interact to minimize emission levels. The performance of the components of the system, as evaluated by full-scale dynamometer testing, is summarized. The over-all effect of the various innovations was a 38% reduction in the recommended ventilation level over that of the bare engine.IntroductionThe Mining Research Laboratories of Energy, Mines and Resources Canada is required, as part o f the certification service of the Canadian Explosive Atmosphere s Laboratory, to test the exhaust emissions of diesel engines, and to recommend appropriate amounts of fresh ventilating air to minimize the risks to health of underground personnel working with, or in the vicinity of, such diesel engines. Volvo BM AB of Sweden made application for the certification of the BM 861 U truck during a period in which EMR personnel were engaged in a number of research projects concerned with improving the environment in dieselized mines. One such avenue of research was the venturi or high-energy scrubber; as the BM 861 U was equipped with this type of scrubber , EMR and Volvo BM agreed to cooperate in a considerably more extensive investigation than would be normal for a certification application. The outcome of some of this research is summarized in this paper."

Jan 1, 1981

By P. D. Duever, P. J. Readyhough, P. L. Silveston

"The Plastojrost apparatus, developed by Ritter and Juranek in the 1960s has been modified primarily, to automatic temperature control. A limited investigation of carboniferous and cretaceous coal samples showed that both coals undergo the same changes when coked in the Plastofrost unit. Dilatometer plastic range and total dilatation correlated well with the Piastofrost plastic range for the carboniferous Appalachian coal, but not for the cretaceous western Canadian coal. Work to elucidate the characteristics of some western Canadian coals using the Plastofrost is in progress. IntroductionCoke quality is critically affected by the properties of the plastic phase in the coal-to-coke transformation. Since these properties exist in a coke oven and are not measurable, they are approximated by standard laboratory tests, such as free swelling index, plastometry, and dilatometry. Of particular interest to us is the anomalous behaviour of western Canadian coals of cretaceous origin. By many predictive methods, these coals should not produce coherent cokes. When coked in pilot scale test ovens, in fact, they produce cokes of good stability. They typically make up 20% of Japanese coking coal blends and are also used in South Korea, Mexico, Brazil, and several European countries. This anomalous behaviour has been studied in our laboratory<8.9.1O). Plastic properties or rheological tests examine just the external ramifications of the coal-to-coke transformation. To understand the process, however, microscopic examination of the coal and coke seems to be needed. The Plastofrost unit has been shown to be a convenient means to this end."

Jan 1, 1987

By H. A. Gorrell

Preliminary studies of the potential for the production of warm water (up to perhaps 150°C) have been carried out in the Plains region of Western Canada. Production might be from depths as great as about 5 km . Natural waters in this temperature range are currently being used for space heating in other parts of the world. The geography and stratigraphy of the Prairie Provinces are reviewed in terms of their apparent potential for warm-water production. Temperature, salinity and other data provided by wells drilled by the oil and gas industry are reviewed and problem areas are outlined.

Jan 1, 1979

By A. G. Scobie

A spectrographic method for the determination of small amounts of gold and the platinum metals in ores has been developed. By means of this method, an assay of 0.001 ounce per ton on one assay ton samples is possible, and by seecrrographic adjustments the sensitivity may be increased to 0.0001 ounce per ton. All the prec10us metals may be determined from one spectrographic arcing with an accuracy of about 5 per cent average deviation from absolute values, and the complete analysis of an ore or similar product may be reported five or six hours after receipt of sample.

Jan 1, 1945

By J. G. Speight

Laboratory studies indicate that autogenous heating of low-rank coal can be prevented by a prior treatment which involves immersing the coal for short (5-15 min.) periods in an inert liquid at temperatures between ~ 350° and 400°C. Such "carbonization" effectively reduces the accessible pore volume of the coal to levels at which heat generation through subsequent sorption of moisture and oxygen is too slow to cause significant temperature rises in a stockpile. In addition, this treatment also irreversibly removes most of the moisture held in the raw coal and raises its calorific value by as much as 10-12%.

Jan 1, 1973

By D. J. MacKinnon

Zinc metal was first produced in India around 1100 A.O. and a zinc industry based on retorting gradually developed in both India and China(1) . The vertical retort method for smelting zinc ores was developed in England in the 1730s; this was followed by the more fuel efficient horizontal retort process developed by the Belgians in the 19th century(2) . The horizontal retort process was the standard method of zinc manufacture until the 1950s when it became obvious that it could not compete with electrolytic zinc technology(2). The present day extractive metallurgy of zinc is dominated by the electrolytic process which now accounts for almost 80% of the world&apos;s primary zinc production. In recent years the electrolytic zinc process has seen significant improvements: the fluid-bed roasting of zinc concentrates, improved leaching and residue treatment techniques such as the jarosite and goethite processes, improved solution purification procedures, mechanization of the zinc electrolysis step and of the zinc melting and casting operation. In addition, new leaching processes have been implemented for the treatment of oxidized ores, particularly silicates, and the pressure leaching of zinc sulphide concentrates is now a commercial reality. Although the electrolytic zinc process was first used on a commercial scale in 1916, its history can be traced back to the 1860s. The purpose of the present paper is to outline the early history of the electrolytic zinc process and to trace the significant developments which led to the first successful commercial electrolytic zinc plants.

Jan 1, 1999

By Jae-Chun Lee, Sadia Ilyas

We investigate the technical feasibility of bioleaching of metals from low grade sulphidic ore. Experiments were conducted with an adapted consortium of Sulfobacillus thermosulfidooxidans and Thermoplasm acidophilum in batch bioreactors (1.5 L), small columns (10 kg ore load, 8 % S0 sludge) and large columns (80 kg ore load, 12 % S0 sludge). Approximately 83 % Ni, 85 % Cu, 55 % Fe and 81 % Zn was leached out in batch mode while 93 % Ni, 89 % Zn, 81 % Cu and 65 % Fe was leached out in column reactors. Bioleaching potential improved by acid pre-leaching, adaptation of microbial consortium and periodic bleeding of effluents.

Jan 1, 2014

By S. Orangi

A representative sample of ramming paste from a peripheral seam in an aluminium electrolysis cell was taken in order to develop a process to fabricate ramming paste samples in the laboratory. To this end, paste material was compacted in multilayers in a mould designed to be representative of peripheral seams in Alcoa&apos;s smelters. The density distribution in the representative sample was measured ranging from 1.51-1.76 g/cm3. The density range obtained by the proposed methodology in laboratory is 1.47-1.77 g/cm3. The results demonstrate that the proposed fabrication method adequately duplicates paste density from the cell for both one and two layer compaction. Finally, preliminary results related to the compressive strength and Young&apos;s modulus of laboratory samples were obtained at various temperatures and are presented in this paper.

Jan 1, 2011

By Kenneth L. Graham

Horizontal directional drilling from existing underground workings will greatly reduce, if not replace, surface exploration drilling. Diminishing ore reserves along with increasing difficulty in acquiring access and permitting of drilling surface holes requires a change in procedure. The length and direction of the required long holes is site specific, but once determined could be quickly mobilized. Data would be available for a much more timely evaluation without any surface disturbance and required reclamation issues. Preplanned directional drilling from underground will also provide an evaluation of already inconsistent uranium deposits located under surface terrain that is inaccessible to surface drilling.

Aug 1, 2010

By A. Taylor, E. Thorn Corthay, J. Farrell, L. A. Westfall, S. Borchardt

Mining and metallurgical industries need to minimize their greenhouse gas (GHG) emissions; Hatch specializes in conducting mining and metallurgical energy management assessments and optimizing productivity. Projects executed have demonstrated that there is a wealth of energy management, waste reduction, and process efficiency improvements that require no or low capital investment. Typical energy cost savings are on the order of 5% to 12%, with similar reductions in GHG emissions. Hatch generates Marginal Abatement Cost Curves to optimize the implementation pathway, maximizing carbon abatement and minimizing cost. The findings of a practical case study from Cameco are presented.

Jan 1, 2010

By Sadough vanini Ali

Hot deformation behavior of functionally graded steel (FGS) was investigated via conducting hot compression tests at different temperatures and strain rates. Functionally graded steels consist of ferrite, austenite, bainite and martensite layers that are made by diffusion of alloy elements during the melting process. The zenerhollomon parameter has been used to describe the flow stress variations as a function of temperatures and strain rates. The parameter values for all the layers via using the boundary conditions was determined based on composite graded behaviors. Furthermore by applying the rule of phase mixtures, the whole strain rate applied on composite would be the sum of layers strain rates considering the layers volume fraction, while the layers have the same stress. Consequently the composite flow stress for each strain rate and temperature was determined.

Oct 1, 2011

By S. Rash Ahmadi

One of the most important elements in power plants is rotors and repairing the damaged rotors is very important in view point of economics. One of the most complicated problems in power plants is increasing of stiffness of the turbine rotors. This problem which occurs mainly due to thermal shock or rubbing makes to exit damaged rotor from service. These elements can be repaired effectively by heat treatment methods. Tempering heat treatment is the most common solution for straightening of damaged rotors but it requires having good knowledge about heat treatment parameters (temperature and time) and their affects on fundamental properties of rotors. In this article, a suitable method is introduced in order to modify the increased stiffness in journal part of rotors due to martensite transformation, using heat treatment tempering process.

Oct 1, 2011

By A Sadough Vanini

In this paper large deformation of smart functionally graded beams with initial imperfection and under thermal loadings is considered. Smart beam consist of two types of layers. One layer is made from functionally graded materials and a layer or a set of layers from active materials that usually is made from piezoelectric materials that are bounded on the surfaces of beam. An active controller is used for controlling the deformation and stress in functionally graded layer of beam. A simple Euler- Bernoulli beam theory is used for analyzing of beam. In functionally graded layer the material property vary continuously through the thickness direction and power law model is used for the variation of elastic modulus, heat expansion and heat conduction coefficients. Poisson ratio is assumed to be constant in functionally graded layer. The effects of varying the power law constants and the Gain of controller is considered here. The results are reduced and compared with smart functionally graded beam without initial imperfections.

Oct 1, 2011

By S. Rash Ahmadi

Thin brittle coatings are deposited or developed on component surfaces for different reasons. In many practical applications the coatings are stressed by externally applied loads. Under such conditions, coating failure can occur. In this paper the probability of the extension of surface crack in coated materials due to cylindrical sliding indentation is analyzed. Contact loading problems typically result in multi-axle and strongly inhomogeneous stress fields near the contact surface. This property which strongly affects the stress intensity factors is taken into account in the failure analysis. Edge cracks were selected to model the actually accruing surface flaws. A suitable method is described for calculating the contact stress fields in coating and substrate. The coating is idealized as a brittle-elastic layer of uniform thickness, which is bonded to the surface of a half space. Method of linear elastic fracture mechanics are then used to calculate the load required to cause fracture in the coating.

Oct 1, 2011

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

"The standards set out requirements of the Toronto Stock Exchange for company’s providing information to investors, regulators and/or the media regarding their mineral properties. In addition, information contained in new releases, continuous disclosure documents [annual report], or other forms of communication [printed investor relations materials and electronic publications] are also subject to these standards.1.0 INTRODUCTIONThe disclosure of the results of exploration and development activity on mineral properties mustcomply with the requirements of the Toronto Stock Exchange Policy Statement on Timely Disclosure, theOntario Securities Act and all applicable policies and rules of the Ontario Securities Commission and anyother securities regulatory body having jurisdiction over an issuer listed on the Exchange. In particular,the requirements of National Instrument 43-101 must be followed.The purpose of the standards is to set out the requirements of the Toronto Stock Exchange when acompany provides information to investors, regulators and/or the media regarding its properties, whethersuch information is contained in a news release, a continuous disclosure document such as an annualreport, or other form of communication, including, but not limited to, printed investor relations material andelectronic publications such as Internet Web sites. These standards do not apply to prospectuses orlisting applications, the standards for which are contained in the policies and rules of the securitiescommissions and the Exchange. These standards are also not intended to establish requirements for thecontent of technical reports.Any information published by or on behalf of a company must comply with these standards. If acompany becomes aware of information published by others regarding its mineral properties which ismaterially misleading to investors, it should take appropriate action to correct such information orotherwise make it known that it is not responsible for publishing such information and does notnecessarily agree with such statements.Disclosure concerning mineral properties should identify the ""qualified person"" as defined in NI 43-101 who is responsible for the work conducted on the property and such person shall have read andapproved of the technical disclosure."

Jan 1, 2003

By S. Rash Ahmadi

Welding is highly reliable and efficient metal joining process. In welding the metal adjacent to the weld joint is subjected to severe thermal conditions. As a result, complex changes in metallurgical structure occur in this region. These changes in structure depend on the material and the temperature history experienced. Friction stir welding (FSW) is relatively a new welding process in which, heat is generated by friction between the tool and the workpiece. The amount of heat conducted into the workpiece determines the quality of weld, residual stress and distortion of the workpiece. The objective of the current work is to study the transient temperature in a friction stir welding. So, a three dimensional transient analytical model is used to study the thermal distribution during the welding. Heat input from the tool shoulder alone is considered in the model. The process parameters like axial load, welding speed and tool rotational speed, used in actual FSW process are taken to build the model. This analytical model is very useful for select the optimized affected parameters in friction stir welding. The model illustrates the comprehensive equation including actual affected parameters in FSW and it can be used for different materials. In addition to the above the thermal history finds application in design of welding tools.

Oct 1, 2011