Search Documents

By G. W. McDonald

"The mineralogical studies done on Hope Brook ore samples indicated that a heap leach gold recovery process may be possible. In the metallurgicalprogram that followed, column tests confirmed this interpretation. A 9300 tonne demonstration heap leach test, in the late fall of 1985, reaffirmed laboratory results while identifying operating conditions that will have to be addressed in a production heap leach plan. Operating plans, gold recoveries and cost areas will be presented.Another important factor in a successful operation is the environment approach.LocationThe Hope Brook gold deposit is located 5 km inland from Cinq Cerf Bay on the south coast of Newfoundland. Port au x Basques is 80 km west and Burgeo 40 km to the east of Hope Brook. As there are no roads in the area, access to the site is by sea or air (Fig. I). The Hope Brook orebody is near the saddle of three watersheds flowing to Cinq Cerf Brook, Boat Hole Brook and Betty's Pond. Acceptable solutions to several environmental concerns can be obtained by using the relative sensitivities of these watersheds.The terrain at the site is generally rolling to hummocky with numerous small ponds separated with rock outcrops and patches of peat covering. Tree vegetation is sparse except in the sheltered areas around Couteau Bay and Cinq Cerf Brook. GeologyThe Chetwynd deposit is hosted by the Lower to Middle Ordovician Georges Brook Formation of the La Poile Group, a thick sequence of volcanic and sedimentary rocks.The Hope Brook Zone contains the largest concentration of gold found to date at Chetwynd. The zone occurs as an intensely silicified lens 100 m to 550 m long (average 400 m) by up to 60 m in width and forms the eastern portion of a more extensive, 4 km long , alteration zone trending at 053 degrees Az and dipping 70 degrees southeast.The Hope Brook Zone contains massive finely granular quartz, scattered blue quartz eyes, 3070 to 8% pyrite, minor calcopyrite and trace molybdenite. Barren silicification envelopes the gold mineralization. The zone is flanked to the southeast by a 200 metre thick aluminosilicate alteration zone and to the northwest by a 10 metre barren pyritic siliceous fragmental rock . The original lithology may be either a thick felsic pyroclastic sequence or a quartz porphyry sill that has been altered by hydrothermal processes. Silica flooding of the permeable host was accompanied by gold deposition."

Jan 1, 1989

By M. Cousineau, S. Gariepy

"Current business and corporate environments push for improving metal accounting practices in smelters. The ensuing projects commonly proceed along a bottom-up approach. As such, efforts are first put on reviewing the measurement system and then on remedying the identified weaknesses. The focus is thus moved to mass/metal balance only after the measurements upgrade process has been completed. However, practice has shown that assessing the high variances related to suboptimal measurement processes is complicated without the help of statistical data reconciliation. This bottom-up approach leads to a to-do list that can not only exceed available resources but also lack prioritization in view of achieving the targeted end use. This paper describes an upgrade project done differently where all the three dimensions of the metal accounting system: hardware, software, and people were instead involved at the onset. Personnel was thus trained on data reconciliation software at the beginning of the project to make the reconciled mass balance benefits available earlier in the upgrading project. This has pinpointed the most critical measurements where accuracy and reproducibility should be improved. Overall, not only the instrumentation retrofitting process has been streamlined, but the global risk for the whole upgrading project has been significantly lowered.INTRODUCTION Mining companies are pressured to improve their production accounting practices in response to the strengthening of corporate requirements for timely and accurate production reporting (Gaylard, Randolph, & Wortley, 2014). Smelters are not spared from these changes. However, their unique situation in the mining value chain set them as strategic targets for upgrading projects. They usually have a longer lifespan than concentrators thereby offering an extended lifecycle to justify investments. Furthermore, numerous smelters have toll agreements with third parties. Accurate cost and production accounting is, therefore, a vital piece of information to fix acceptable contract conditions. Mining companies are ultimately aiming at a clearer view of the operating performance of each business unit to improve their business decisions in a competitive environment. This sought for increase in visibility through plant performance can only be achieved through an upgrade of the metal accounting system. Figure 1 shows the different components of a state of the art system (Gaylard, Morrison, Randolph, Wortley, & Beck, 2009)."

Jan 1, 2017

By Botao Lin, Yan Jin, Hongjuan You, Jingjun Pan, Huiwen Pang, Mian Chen, Sen Chen

"Steam Assisted Gravity Drainage (SAGD) has become the mainstream technology for ultra-heavy oil recovery in Xinjiang oilfield, the success of which depends heavily on shortening of preheating period as well as forming homogeneous and highly permeable zone in land-facies oilsands layer. Towards this aim a special hydraulic fracturing process is required, which is accomplished through controlled water injection to a pair of horizontal wells in order to create homogenously distributed microcracks in the zone between the two wells. The associated mechanical response, however, is unclear for land-facies Karamay oilsands that is loose in texture. In this regard, this research utilizes a triaxial test system on cylindrical specimens extracted from field-collected oilsands cores. Isotropically consolidated drained triaxial compression tests are conducted on both saturated and unsaturated specimens so as to investigate the mechanical response of oilsands at different spots relative to the wellbore. Moreover, acoustic emission and fast pulse-decay permeability are performed to monitor fracture development and permeability evolution. Based on these experimental studies, the mechanism of dilation in oilsands is comprehensively analyzed. The findings reveal distinctive behavior between the saturated and unsaturated specimens as respect to dilation, porosity/volumetric evolution and change of permeability. It is also found that shear bands can be created upon shearing on triaxial specimens, rendering porosity or volumetric strain the factor that is more proper for evaluation of stimulation efficiency in the field.INTRODUCTIONXinjiang oilfield is widely known for its abundant deposit of heavy and ultra-heavy oil that has been estimated to be several hundred million tons. The ultra-heavy oil deposit located in Fengcheng region of Karamay at the northwestern part of the Junggar Basin, Xinjiang, China, has over 360 million tons of resource (Yuan et al. 2013). The resource is deposited in depths from 180 to 450 m and has viscosity over 100, 000 mPa•s at a temperature of 50ºC, bringing technical challenges to recovery activities."

Jan 1, 2015

By Dougla McDonald, Richard Poulin

"Most mine managers in Canada today will agree that one of the keys to mining efficiency and productivity is their human resources. A5 a result, many mines develop some sort of incentive designed to tap their employees' capabilities to the fullest extent. Historically, the most common plans used have been ""piece-rate"" plans, where individual or small groups of miners are paid a financial bonus based on some measure of their productivity. Recently, however, incentive plans that take a more team-based approach have been developed in some Canadian mines. One such plan will be defined in this paper, and its popularity in the industry today discussed.Gainsharing PlansThere are two primary components to a gainsharing plan. The first is a cash incentive, which is paid to all employees and based on factors that are highly correlated with employee productivity, and key to the profitability of the mine. For example, the typical gainsharing cash incentive is based on the cost/unit of metal produced. Management (in consultation with employees in some cases) will establish the budgeted cost per tonne, and any savings in this amount is shared between the company and the employees. The second is a management philosophy and associated communication network, which is designed to foster an environment that encourages information exchanges, communication, participation, and trust between employees and management. The typical gainsharing communication network consists of two tiers of committees. The first, operational committees, include all employees working in the same department or departments which frequently interact. The employees meet monthly with management personnel to discuss problems encountered and brainstorm for solutions. In most cases, these committees will nominate a person in the group to structure the meeting to maximize its efficiency. The second, the screening committee, is a single group consisting of representatives from the various operational groups, whose primary job is to ensure that the plan is effective, and the objectives and results generated by the plan remain consistent with the mine objectives. In short, gainsharing plans tell employees that their bonus depends upon performance and then gives them the opportunity and incentive to affect that performance. The opportunity is provided by a communication network and positive management practices, and the incentive comes in the form of ""intrinsic"" rewards of participation and the ""extrinsic"" rewards of the bonus payments. Figure I will clarify the relationship between the intrinsic and extrinsic rewards."

Jan 1, 1995

By B. K. Ayres

Modern management of uranium mine or mill waste storage facilities (WSFs) often requires that they be remediated or decommissioned with a cover system. In addition to creating a self-sustaining landscape that supports the end land use, cover systems are intended to reduce long-term risks to human and ecological receptors from the stored waste to acceptable levels. The performance and longevity of a cover system will be strongly influenced by the features or shapes of the WSF final landform. Hence, cover systems and landforms must be thought of as an integrated design. Based on the author’s experience, the most important elements of the design process for maximizing the potential of WSF final landforms / cover systems being sustainable over the long term are noted in this manuscript. Several key items that must be considered and addressed during the planning phase of constructing a WSF final landform are also described. Various methods for monitoring performance of a WSF final landform are also reviewed. Key aspects associated with decommissioning a tailings WSF and waste rock pile at the former Cluff Lake uranium mine in northern Saskatchewan are included to illustrate many of the practical insights provided in this paper.

Jan 1, 2020

By A. Supomo, H. Resendiz, C. Burbidge

"Freeport-McMoRan Inc. (FMI) commissioned the expansion of the Morenci Metcalf concentrator in 2014. The concentrator included many design and equipment innovations, including the first-of-its-kind Metso Hydraulic Roll Crusher (HRC), variable speed ball mills and variable speed crushers. In addition to the innovative design, FMI commissioned the Metso APC team to design a realistic process simulator and the plant APC. The process simulator was utilized to train operators before commissioning, which led to a smoother plant start up. The plant APC utilized the concept of dynamic constraint control, which controls the feed to the primary ball mills by “pulling” the tons from crushed rock storage bins, which then automatically are filled by the upstream HRC and secondary crushing circuits. The primary ball-mill control also adjusts the water addition to the cyclone clusters to avoid overload and achieve sufficient grind size. The constraints include in-circuit constraints for feeder capacity, screen-deck capacity, ball mill power, cyclone mass flow, pump capacity and pump motor capacity. The APC system was implemented shortly after the start of commissioning and immediately demonstrated increased throughput and an ability to highlight and quantify process constraints and bottlenecks. The following paper outlines the control strategy, discusses system implementation, results and challenges.INTRODUCTION The FMI Metcalf Concentrator is located in Morenci Arizona on the site of the old original Concentrator. The new Metcalf concentrator started operation in May of 2014. This plant was designed for an average of 63,500 tpd (70,000 stpd), increasing the total Morenci concentrator complex production to a nominal 113,400 tpd (125,000 stpd). The process flow diagram is shown below in Figure 1.The process consists of primary crushing feeding a coarse ore stockpile followed by secondary crushing operating in closed circuit with vibrating screen decks. The screen undersize feeds the first of its kind Metso hydraulic roll crusher (HRC) operating in a closed circuit with vibrating screens. The primary crusher is a Metso 60x110 gyratory crusher. Secondary crushers are Metso MP1250 Crushers with variable speed drives. Secondary crusher discharge is recycled to the dry screen feed bin and screened with oversize returning to secondary crushing and undersize feeding the Metso HRC3000. The product from the 3.0 meter X 2.0 meter roll crusher is wet screened with the undersize feeding the grinding circuit, which is comprised of two each 24-foot diameter by 40- foot-long variable speed ball mills running in parallel with each in closed circuit with a cyclone bank of 12 cyclones. The wet screen oversize is recycled to the HRC feed bin."

Jan 1, 2019

By A. Eltringham

Operations downstream of mining and beneficiation are still being subjected to increasing scrutiny as highly capitalized projects have been either slow to achieve their targets or have actually failed to do so. Leaching and smelting projects have fundamentally high calls on capital and technology as reaction rates are increased and the capture and disposal of unwanted products are subjected to greater restrictions. Separating value from waste inherently becomes riskier as the purification of the desired product imposes greater demands on the process to produce benign wastes. When we superimpose on the chemistry of the project severe predictions of throughput rates, that bring in facets of manufacturing, we are introducing complexities that the records show are not handled well. This paper discusses some of the more common challenges that operators face and what methods are available and are likely to be successful in preventing the loss of value as projects are brought on-stream. This thinking needs to start much earlier and at greater intensity than our industry has normally chosen to employ.

Jan 1, 2011

By R. T. Jones

"Technical publications in the field of mining and metallurgy have existed for a long time. Recent developments in electronic publishing on websites make it possible to disseminate information more widely and cost effectively than before. Professional societies have an opportunity to serve their members and their industry by publishing high-quality peer-reviewed papers on their websites as well as in printed form. Older publications can be scanned, and optical character recognition can be used to provide searchable text. Various business models exist around this process. This paper outlines the approach used by the Southern African Institute of Mining and Metallurgy (SAIMM) to provide free open access to their journal papers and conference proceedings, as well as the work being done by OneMine.org to collect technical papers from a number of international societies and make them available to subscribers via a large database. An approach is outlined that should be of benefit to authors, readers, and society at large.INTRODUCTIONGeorgius Agricola (1494-1555) was not the first writer on the subjects of mining and metallurgy, but is well known as the author of De Re Metallica (‘of things metallic’ or ‘on the nature of metals’), a book that documents and illustrates the observations he made in the course of his extensive travels in the 1500s. Agricola wrote extensively about mining methods and metallurgical processes that were in place in the Middle Ages. The original Latin version of De Re Metallica was published in 1556, the year after Agricola died. It was translated into English by Herbert Hoover, a mining engineer and later President of the United States, and his wife Lou Henry Hoover, a geologist and classicist. The English version of De Re Metallica was published in 1912."

Jan 1, 2012

By J. Ouellet

The design of hydrostatic liner for a deep potash mine shaft in Saskatchewan poses tremendous technological challenges. Technology has evolved to a point where one could consider a new innovative approach to hydrostatic liner design. But there is still a place for conventional technologies such as cast iron tubbings. As will be discussed in this paper, improvement to manufacturing process, installation procedures and even new materials can bring this technology to an excellent level of performance. With the spur of new projects in the potash industry of Saskatchewan, the authors worked in various shaft liner designs from the conceptual stage through to the construction phase. They were either directly leading the design work on some of these projects or acting as an external reviewer on others. Most of these shaft liner designs involved cast iron tubbing technology and ground freezing. The major challenge in sinking potash shafts in Saskatchewan is to go through a water-bearing ground formation under high pressure, known as the Blairmore or Manville fm. The only proven stabilizing technology for these formations is ground freezing. For a potash shaft, dry shaft conditions are highly desired, so a fully waterproof hydrostatic liner is required. All the existing potash mine shafts in Saskatchewan, except for two with composite steelconcrete lining, used the cast iron tubbing technology. Two new shaft tubbing liners have been constructed recently, one in the Athabasca Basin and one for a potash mine in Saskatchewan. When the authors began working on these new projects, what became quickly evident is that the technological knowhow for designing and constructing tubbing liners was no longer available within Canada and that the past construction methods used to sink tubbing lined shafts was obsolete. The tubbing liner for the shafts sunk in the sixties were designed either by German or British companies. In both of these countries only few tubbing lined shafts were sunk in last 40 years and the technology used in the sixties was not improved. There are only few countries where tubbing is routinely produced and installed: China, Russia, Ukraine and Poland. Out of these countries Poland is the one where this technology is the most advanced. The authors, working in close collaboration with engineers from Poland, attempted to rebuild this knowledge for the mining industry in Canada. This process involved thorough analysis of old technical reports, literature review and study of current polish design and construction practices as well as site visits of existing shafts. Through actual construction experience, some lessons were learned as well as ideas for improvements. In this paper, the authors will present a succinct review of design and procurement process. But, the practical aspects of the construction and installation methodology will be treated with more emphasis, more specifically the practice leading to good liner performance. Some of the poorly understood technical aspects of tubbing installation will be discussed more thoroughly and some currently accepted myths dispelled.

Aug 1, 2013

By E. Henderson, L. K. Daneshmend

Drawpoint control is critical in determining the cutoff point for load-haul-dump mucking operations to minimize dilution. It is also necessary to ensure even mucking distribution and to prevent possible hang-up of material within a stope. A prototype production monitoring and reporting system has been developed for load-haul-dump operations in under-ground mines. The system generates accurate and timely information regarding mucked tonnages and drawpoint and ore/waste pass utilization. The monitoring system integrates a PLC-based load weighing system with a radio frequency identification (RFID) system for locating the vehicle. The system records the identification and time of entry and exit of each draw-point and ore/waste pass visited during a shift, as well as the weight of each bucket load. A trial of the system was conducted at the CAN-MET Experimental Mine near Val d’Or, Quebec. The monitoring and reporting system functioned as designed, with the exception that the maximum read range of the RFID tags under dynamic conditions was found to be a limitation. RFID systems with greater range capabilities have been identified for a second generation system. The system is the first of its type in North America to demonstrate that RFID tagscan be successfully applied to locate trackless underground equipment. Because of their ability to locate equipment and personnel within underground mines, RFID systems should be considered a key technology for future mine information and process control systems.

Jan 1, 1996

By Cesar A. Urbano Jr., Gretchen T. Lapidus

A series of experiments examined silver extraction from a high-grade sulfide concentrate employing thiourea solution. Thiourea was initially oxidized with hydrogen peroxide (H2O2) to form formamidine disulfide (FADS) and used to extract silver from the as-received concentrate and after various pretreatments. Very low recoveries (~30%) were obtained with the as-received concentrate due to competitive cementation reactions by metallic iron and easily oxidizable copper phases. Over 80% Ag recovery was obtained when the concentrate was pretreated to remove this iron and copper. The results suggest that an oxidative acid pretreatment of this concentrates significantly improves silver recovery upon leaching with thiourea.

Jan 1, 2014

By J. J. Crowder, A. L. Coulson

Ground support is a significant component of underground mining costs. The rehabilitation of failed support, however, is often much more expensive than the initial installation. This paper investigates whether the right type and length of support can be designed correctly the first time, through forward modelling of the support and the mining process. Back analyses demonstrate how high-quality instrumentation and monitoring can help with the estimation of the post-peak (post-failure) rock mass parameters required for a comprehensive analysis. A hybrid modelling approach combines a three-dimensional mine-wide boundary element model with a non-linear finite element model to allow for the failure process in the rock mass. The back analyses demonstrate that, for the case study site, the post-peak Generalized Hoek-Brown value of mr must be reduced significantly in order to properly simulate displacements observed in instrumentation data. High-quality instrumentation data is the key to post-peak rock mass parameter calibration. The procedures outlined in the paper highlight the need for a new hybrid numerical modelling package that can use the influence of three-dimensional mining-induced stresses to predict displacements in, and potential failure of, rock masses surrounding mining infrastructure in order to radically alter strategic and tactical mine design.

Jan 1, 2007

By Noel W. Kirshenbaum

Difficulties and costs of transport markedly affect Canadian mineral producers because of distance from markets, weather conditions and rugged terrain. The chemical and physical nature of sulphide concentrates presents additional difficulties in handling and transport, resulting in higher costs which are ultimately borne by the mineowner. Troublesome properties include the thixo-tropic character of wet concentrates, freezing, susceptibility to autogenous heating, and fine particle size causing spillage and dusting losses. Canadian mineowners and shippers must contend with these problems and with stringent regulations governing the maritime shipping of concentrates. A "systems approach," in which complementary techniques in materials preparation, handling and transport are integrated, could reduce freight costs and losses for those selling concentrates, facilitate operations for those carrying and handling them and, in some cases, improve metallurgical processes in smelters receiving them.

Jan 1, 1969

By J. C. Mitcheson

Mr. President, Mr. Mayor, Ladies & Gentlemen: IT GIVES ME great pleasure to have the opportunity, today, to speak on behalf of all the constituent. bodies of the Common-wealth Council of Mining and Metallurgical Institutions. For the past month we delegates have been right royally entertained across the length and breadth of Canada by Provincial Governments, City Councils, and other equally generous public organizations and private corporations. On this occasion, however, the President of The Canadian Institute of Mining and Metallurgy, our good friend Dr. H. J. Fraser, has been our host at the enjoyable reception preceding this Institute Luncheon, which luncheon was sponsored by our official host, The Canadian Institute of Mining and Metallurgy, one of our .constituent bodies.

Jan 1, 1957

By N. J. Duncan

"Coal mining, whether surface or underground, has hazards that make it unique in the field of industrial safety and health. The often soft, faulted and folded sedimentary strata make wall or roof movement a risk to the safe and economic removal of the coal, while the extraction and handling of coal may create an explosion hazard even in surface operations, In Canada, these problems are compounded by the situation of the coal fields which range from deep undersea deposits in Nova Scotia to steeply pitching thick coal seams high in the Rocky Mountains. Climate too can create its own problems, particularly the effect of metals of minus 40°C temperatures, as crumpled dragline booms at prairie strip mines witness. Because of the difficult and sometimes hazardous conditions, Canada's underground colliery managers, in common with those of other Commonwealth coal-producing countries, must have a government ""certificate of competency"" before being appointed as mine managers. Certification of assistant managers (""under-managers"") and foremen (""fire-bosses"") is also a legal requirement for all of Canada's underground collieries, while the province of Alberta requires certification of surface management personnel. Electricians and mechanics who install and maintain the specially designed equipment underground and in hazardous areas of surface mines and processing plants, and mine surveyors who ensure accuracy of the location of underground workings, must also hold government certificates of competency. The requisites for all certification include a minimum work experience and knowledge of coal mining technology and mine safety and health legislation. Despite recognition of the hazards and increasing knowledge of methods of preventing explosions of flammable gas and coal dust in Canada's underground mines, there have been several disastrous explosions such as those at Springhill Colliery in Nova Scotia in 1891 with the loss of 125 lives, at Hillcrest Colliery in Alberta in 1914 with 189 dead, and more recently · explosions and fires in No. 20 and No. 26 Collieries in Cape Breton. Preventing explosions has required developing optimal ventilation techniques, reducing ignition potential, suppressing ignition at source, draining flammable gas before it can enter the air courses, and preventing, or sealing off, autogenous heatings with their associated carbon monoxide or explosion dangers."

Jan 1, 1985

Over five decades ago Kitchener et al. in England and La Mer and Healy in the US were advancing our understanding and application of flocculants, primarily related to water treatment and filtration of sludge. This paper identifies the beneficial uses of flocculants in the mining industry and revisits some less common applications. Flocculants are used in unique ways in the mining industry: (a) to increase the effectiveness of sediment ponds to achieve discharge compliance; (b) to eliminate air emissions and costs associated with concentrate drying; (c) to reduce soil loss by applying a flocculant to erodible soils, and reducing wind and water erosion; (d) to remove/thicken metal precipitates in acid rock drainage treatment; and (e) to enhance clarification and thickening in mineral processing. The mechanism of how flocculants, coagulations and potentially-determining ions function is described and how their use can be controlled and optimized. The potential toxic effects of flocculants and coagulants when used to achieve effluent permit discharge compliance for suspended solids is discussed. A review of numerous best management practice (BMP) guidelines for the design and operation of sediment ponds treating mine site runoff to remove total suspended solids (TSS) and turbidity revealed an absence of a predictive methodology to address regulatory discharge compliance for TSS concentration, turbidity and flocculant-induced toxicity. An essential component of pond design is the need to determine whether flocculants and/or other settling aids are required based on the site-specific soil particle size distributions upslope of the pond. Procedures are provided to predict the need for settling aids and estimate pond discharge quality and downstream impact for TSS, turbidity, toxicity and sub-lethal toxicity. The need to develop BMP guidelines are discussed for (a) the application of flocculant to surface soils to reduce erosion, (b) the application of flocblocks to increase the ?sediment control? aspects of erosion and sediment control, as part of the mine site erosion control plan strategy and (c) the application of flocculant to silt socks to treat mine site runoff.

Aug 1, 2013

By John Galbraith, Dwayne D. Tannant, Chris C. Langille

"Development of underground openings in a deep mining environment requires a support system that is able to absorb energy as a result of dynamic loading due to rockbursting and blasting and static loading due to convergence as the development face advances. The support system must be resistant to corrosion and be effective over the life of the excavation, upward of ten years, yet simple and cost effective to install. Over the past two years, research has been conducted at INCO’s Creighton Mine to try and identify a one-pass grouted support system that will meet these needs.The main problem faced, with simply using grouted rebar at depth, is the effect of tunnel convergence on the stiff grouted bolts. Typically, if fully grouted, stiff rebar are installed to the face of an advancing development heading, the amount of convergence that occurs can result in failure of the bolts at the face plates used to attach the mine screen to the back. An initial support is required to enable crews to continue the bolting cycle in the immediate term, yet allow for this convergence over the longer term as the drift advances. The ideal support system will allow both to occur, giving effective immediate support while providing long-term effectiveness in allowing convergence to occur while maintaining the capacity of the bolt.This paper will investigate the expected convergence in deep development headings at +2200 m (+7200 ft) through the use of direct measurements using both flex rod extensometers grouted into the back of a development heading and five-point tape extensometer stations. Measured results will be compared with simple2-D numerical analysis to evaluate the anticipated convergence expected to be absorbed by the bolting system. The required convergence will then be compared with load deformation response of several support configurations."

Jan 1, 1996

By S. Dominguez, E. Gebrehiwot, S. Richardson, S. Sandoval

Copper electrowinning/electrorefining (EW/ER) is powered by direct current (DC) rectifiers that typically generate 30,000 to 70,000 amps and a bus-bus voltage of 200 to 500 volts DC. Tankhouses are designed so that DC current flows through “cell lines” which contain individual EW/ER cells electrically connected in series. Electrolyte composed of copper sulfate and sulfuric acid in water forms the “liquid conductor” that connects the metallic conductors in this circuit. In this setting, stray current is a DC current that strays from and therefore bypasses the tankhouse circuit by finding a path to ground, often through the electrolyte in pipelines that feed into and discharge from the cells, or through dried electrolyte (i.e. sulfate), which is also electrically conductive. Tankhouse workers can be exposed to shock hazards if they become part of a stray current path to ground. This presentation details examples of stray current shock hazards in electrolytic tankhouses and provides voltage and amperage measurements associated with stray current in these examples. A review of critical safety controls in EW/ER tankhouses that will mitigate the risk of employee shock from stray current is also provided. INTRODUCTION Electrolytic tankhouses are designed to deliver relatively large amperages of DC current to a series of electrolytic cells in which copper is plated out of solution using the classic anode-cathode pair geometry within each cell. Electrolyte is the “liquid conductor” that transfers current in between the metallic conductors of the cell. The metallic conductors include inter-cell copper bus bars and the anodes and cathodes themselves. It is sometimes forgotten that electrolyte as a conductor is capable of delivering DC current outside the designed circuit of a tankhouse. Stray current is a DC current that strays from the tankhouse electrical circuit by finding a path to follow other than the designed path. Safety becomes a concern when there is a risk of an employee becoming part of an accidental stray current path, thereby suffering an electrical shock. In 2016, Freeport-McMoRan (FMI) suffered a fatality at one of its copper electrowinning tankhouses. The forensic analysis concluded that stray current from the tankhouse rectifier contributed to the fatality. An employee accidentally fell into contact with a metal flange at the end of an HDPE pipe that was collecting cell overflow electrolyte from the tankhouse. DC current passed through the employee to ground, creating a shock that was judged to contribute to his death. The situation was exasperated because the employee was unconscious, and therefore was exposed to the stray current for several minutes before being found. In addition, the employee’s clothing was saturated with liquid, and the employee was found kneeling in puddled liquid on the ground. FMI immediately began an investigation into the root cause of the stray current that was measured at the scene. Sufficient electrolyte had accumulated in the HDPE pipe such that a continuous path was formed between it and electrolyte that was continuously overflowing from energized electrowinning cells. The metal flange on the pipe was the metallic conductor that carried the current to the employee from the electrolyte inside the pipe. Current then flowed through the employee to ground. Because of this incident, FMI undertook an extensive review of the hazards of stray current in EW/ER. FMI’s tankhouse workforce received a Tankhouse Electrical Safety training course developed in- house to insure worker understanding of stray current hazards. Tankhouse design changes were implemented to better insulate workers from stray current. Personal protective equipment (PPE) standards were also reviewed and changes made.

Jan 1, 2019

By Dennis Martin

What is Borehole Hoisting Borehole Hoisting is the use of a hoisting plant to hoist rock, workers and materials or both, vertically through a borehole, between a mine level and surface or between two levels of an underground mine. Screen and bolt ground support on walls of 5.5 m diameter borehole hoisting shaft

May 1, 2013

By R. W. Wein, L C. Bliss

Northern ecosystems are dominated by a harsh physical environment which dictates a need for biological adaptation. As yet, it is unknown just how these adapted plants and animals will tolerate industrial development. Our work, sponsored by university, government and industry, is part of an effort to evaluate this developmental impact. Our present studies and the results to date will be discussed. Other problems to which the environmental student may address himself in the future to ensure against environ-mental degradation will be suggested.

Jan 1, 1971