Search Documents

By Warren A. Sheaffer

THE chief uses for copper are as a conductor of electricity and as the chief component in brasses and bronzes. For such uses, the copper must be of very high purity. H the impurities are zinc, iron, lead, arsenic, or antimony, they can be removed to a great extent by fire-refining. H, however, gold, silver, nickel, or cobalt are present, electrolytic refining is necessary. Electrolytic refining must be preceded by fire-refining and hence all impure copper must be fire-refined. The electrolytic refining of copper is most efficiently carried on when the impurities in the anodes are at a minimum. Some of the impurities tend to deposit with the copper at the cathode, while others remain in solution, decreasing the conductivity of the electrolyte and thus increasing the voltage necessary for refining. Since these dissolved impurities must be removed by continuous purifications, the amount of impurity in the anode copper should be reduced by furnace refining to some predetermined limit. Anode furnace operation aims to reduce these impurities to a minimum beyond which the cost of further furnace refining would exceed that of removing the remaining small amounts of impurities from the electrolyte. The anodes should have a fine-grain internal structure because any pieces of metal becoming detached from the anode during the electrolytic refining are inconvenient to remove from the cells and may cause short-circuits. Impurities tend to disrupt such a structure and thus form zones of weakness during corrosion. When the impurities are reduced to a satisfactory mini-mum, the anode, due to having a fine-grain structure, will corrode uniformly over the entire surface area exposed to the electrolyte. Oxides of the impurities may be volatile, in which case they pass off as flue gases, or they may form viscous slags having a lower specific gravity than molten copper, thus permitting their removal by skimming. Some impurities can be oxidized by introducing air into the bath. Due to the large solubility of oxygen in molten copper, oxygen is distributed uniformly throughout the bath and thus comes into intimate contact with all impurities. The oxides which are insoluble in molten. copper are removed either as flue gases or as slag.

Jan 1, 1942

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By The Satff

"TEXADA Island is situated in the Strait of Georgia, about 100 miles northwest of Vancouver. The property of Texada Mines Ltd. lies on the southwest coast of the northern end of the Island. A part of the ""Sunshine Coast,"" the climate is moderate, with about 30 inches of rain during winter months and relatively dry summers. Texada has been shipping high-grade magnetite concentrate continuously since 1952 to Japanese ore buyers. In 1959, a 3,000-foot tunnel was driven just above sea level to explore the possible downward extension of known orebodies then being mined by open pit. In January of 1961, because the open-pit operations had a limited life, C. C. Huston and Associates were brought in as mining consultants to do a feasibility study on the possibility of going underground for production. This study was completed in March, 1961. With the completion of the report, the Company went to Japan seeking a ,long-term contract to justify the capital outlay necessary for setting up an underground operation. Concurrently, underground diamond drilling revealed more ore, and the Company planned some modifications to the concentrator for increasing the copper recovery. By November, 1961, a ten-year contract was signed with Japanese ore buyers for the sale of 450,-000 long tons of concentrates beginning in October, 1963. Since that time, the Company has built its own 65 000-ton ore carrier and an additional three-year contract has been negotiated, with an annual tonnage increase of from 450,000 to 550,000 tons."

Jan 1, 1967

By N. K. Jaber

The "Pidgeon Process" for the extraction of magnesium from dolomite ore utilizing ferrosilicon as the reducing agent has been studied extensively by active metallurgists such Mr L,M, Pidgeon the father of this process, Most of the work sited so far has focused on heating the (FeSi/MgO,CaO) briquette mix under vacuum in stainless steel retorts by external fuel hydrocarbon heating, In this work Electrical Induction Heating was employed as the heating method whereby the briquette mix was placed in a steel crucible around which an Induction Heating copper coil was wound and placed inside in a stainless steel vacuum tank, It was observed that by virtue of the fast Induction Heating method utilized in the silicothermic extraction process higher reduction temperatures were reached in shorter periods of time due to fast heat transport into the ore charge mix, This facilitated shorter metal reduction times as compared to the conventional fuel heating methods.

Jan 1, 2006

By J. A. Chamberlain

DURING a recent trip across Canada and parts of the northern United States, the. writer examined some forty mine models. Construction -details and the uses to which the models were being put were outlined in a report to Eldorado Mining and Refining, Limited, and a specific model was proposed on the basis of the Company's particular needs at their Beaverlodge operation. It was felt, however, that portions of the report would be of some value to anyone contemplating building a mine model. For this reason, a synopsis of some of the more important aspects of the problem is presented here, together with a suggested model type that appears to have wide application. Thanks are due not only to Eldorado for permission to publish the following material, but also to the many mine personnel across Canada who allowed the writer to examine their models and gave freely of their time in discussion.

Jan 1, 1958

By Jiuhua Xu, Shuiku Jia, Weiren Sun

"The Jinqingding gold deposit, situated in the east Jiaodong Peninsula of Shandong province, is typical of the pyrite-quartz vein gold deposits in the Muping-Rushan gold belt of China. The gold deposit is controlled by a great NNE fracture zone and is composed of several lenticular orebodies within the fracture rone occurring in the Kunyushan granite massif. The Kunyushan granite massif was formed by the replacement of the Archean Jiaodong group.The main minerals associated with gold are pyrite, chalcopyrite, galena and sphalerite; the gangue minerals are dominated by quartz, sericite, microcline and calcite. The mineralizing event can be divided into four stages: (1) pyrite-quartz; (2) quartz-pyrite; (3) siderite-polymetallic sulfides; and (4) calcite-quartz. Gold occurs mainly as native gold and electrurn in stage I and stage II. There are some evident differences between pyrite from major stages of gold mineralization and that from minor stages; these include differences in crystal forms, size and composition of fluid inclusions.Wallrock alterations consist of sericitization, silicification, pyritization and potash-feldspar alteration. Five alteration zones can be distinguished from unaltered granite (zone 0) to vein lodes (zone IV). Au and Ag increase rapidly from zone 0 to rone IV, Cu increases continuously, while Pb and Zn increase slowly. R-type geological factor analysis indicates that the Au, Ag, Cu, Pb and Zn bear a close relationship to wallrock alteration."

Jan 1, 1994

By H. Huang, R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic to neutral solutions, over the pH range 1-7, to determine a potential range for co-dissolution. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated EH-pH diagrams for the copper-arsenic-sulfur-water system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Jan 1, 2014

By V. C. Wansbrough

First, permit me to say with what very great pleasure we find ourselves assembled in this most ancient and honourable city of Quebec. It is a city which we deeply respect as the fountain-head of the culture of French-speaking fellow citizens, and the seat of government of a province which is steadily recording new achievements in Canadian mining. Such achievements prove what can be accomplished when enlightened and progressive government policy, technical and scientific competence, and private initiative pull forward together in harmonious rhythm. It is a most happy and auspicious event also that the guiding control of the affairs of the Institute and of the fine traditions of provincial administration have for the past year been united in the person of our honoured President, Dr. A. O. Dufresne. This year, again, we have bad prepared for us by our hosts a splendid programme of technical sessions and social entertainment. Each year we pay an unspoken compliment to the Institute, expecting as a matter of course nothing but the highest standards in both these spheres. In its annua1, semi-annual, and regional meetings, in the constant activity of its local Branches, the Institute continues with marked success to perform its great dual service, social and educational. We are all its beneficiaries to the extent to which we choose to profit by participation in its affairs. But, one imagines, to none are the advantages of Institute membership more valuable than to young men embarking on their professional careers.

Jan 1, 1951

By H. A. Oaks

FROM 1921 to 1939, the aeroplane played an increasingly important role in Canadian prospecting and mine development. This service has been interrupted by the war, but undoubtedly it will be accelerated in the postwar years, if suitable aircraft are available. The purpose of this paper will be to review the uses to which the aeroplane has been put in prospecting and development in the past, and its future possibilities as an aid in prospecting. If by review, and deduction, we get a clear picture of what we expect the prospecting plane to do, we may be able to arrive at a very close approximation of its required characteristics and, from this, an idea of costs. &apos;Function&apos; is defined as the mode of action by which it (the aeroplane) fulfills its purpose. We will endeavour, therefore, first to find what this purpose is, or should be, so that our expectations will not be too limited nor too great-and then find, by analysis, what performance we require in an aeroplane to meet our reasonable expectations at an economic price.

Jan 1, 1945

By Ken Hester, Bruce Arthur

"Introduction""Pebble milling"" is a term used to describe secondary grinding done with rock pebbles rather than steel balls or other steel or metal shapes. This paper discusses pebble milling with particular attention being paid to uranium grinding circuits.Pebble milling is typically employed:a. where the cost of steel balls becomes exorbitant, as may be the case in an isolated area.b. where the extra steel added from steel ball consumption may be detrimental to further processing.c. where the over-all economics favour the use of pebbles rather than ball.Pebble milling differs from autogenous and semi-autogenous grinding in that a sized product has been removed from some part of the primary comminution circuit, and it is this sized product which is added as grinding media to the pebble milling stage. The pebbles do not necessarily have to be produced from the ore- ""foreign"" pebbles can be used. Also, pebble milling generally refers to grinding from a fine size, below about 6 mesh (3360 micron), with relatively small media, that is, secondary grinding. In South Africa, however, primary pebble mills are sometimes used to grind crusher house product, and thus function in place of rod mills. Pebbles for this service are large and heavy as they must weigh as much as balls used in similar service.The first large applications of pebble milling were in South Africa(n. ""Tube milling"" with pebbles started in 1904. The tube mill was simply a tumbling mill with a length to diameter ratio over two. A ""typical"" early tube mill was 5.5 ft. (1.7 m) in diameter and 16 ft. (4.9 m) in length. Diameters increased steadily. King(n mentions 8-ft. (2.4 m) units in his 1949 book. By 1961, the largest units discussed by Jackson('' were 12ft. (3. 7 m) in diameter."

Jan 1, 1989

By P. Srinivasan

Corrosion is a major operational problem in amine-treating plants causing significant expenditures each year, Corrosion may become more severe when the amine plants contain process contaminants ? namely heat-stable salts. The heat-stable salts enter the plants with feed-gas streams and makeup-solution, and/or are produced within the plants by reactions of alkanolamine and available carboxylic-acid anions, This work investigated interaction corrosion effects that may exist in amine-treating plants containing a mixture of heat-stable salts, The investigation was experimentally carried out in a 5 kmol/m3 monoethanolamine (MEA) solution containing 0,20 mol/mol carbon dioxide (CO2) loading at 80°C under atmospheric pressure using carbon steel 1018, Six heat-stable salts, including formate, oxalate, bicine, acetate, thiosulfate and chloride, were tested with a series of salt combinations, Potentiodynamic Polarization, Tafel Extrapolation, and Cyclic Polarization were used for revealing corrosion behavior, determining corrosion rate, and examining the pitting tendency, respectively, Results show that thiosulfate induces the most corrosive environment when present either individually or in the form of salt mixtures.

Jan 1, 2005

By S. J. Buckler

Many metallurgical processes use submerged gas injection to increase the contact area between gas and liquid phases in order to promote faster overall reaction rates. The work presented in this paper is part of an experimental investigation to measure the gas-liquid interfacial area available in bubble plumes within molten metal baths. Measurements of the nitrogen absorption rate during submerged injection into molten iron baths have been used to estimate the interfacial areas of the bubble plumes. A theoretical model was used to predict the superficial nitrogen transfer rate under mixed liquid phase mass transfer -interfacial reaction control. The interfacial area was calculated by dividing the overall nitrogen absorption rate by the superficial rate. Reasonable agreement was obtained between the interfacial areas measured in our laboratory with data from a comparable system reported in the literature. The experimental results were compared with the predictions of three theoretical models and one empirical correlation. The models of Turkdogan (3) and Zhao and Themelis (5) gave the best agreement with our data.

Jan 1, 2004

By E. B. Wilson

"Although the Operations Research technique of Reliability Theory has been applied with marked success in many fields, including the Apollo spaceship programs, the concept of reliability has not been generally adopted in mining and other heavy industries. Of course, reliability, or the probability that a system will be able to operate without a failure for a given interval of time, does not require the same emphasis in mining as in the aerospace industries. Nevertheless, certain aspects of Reliability Theory can be followed advantageously. For example, reliability calculations can determine the best time to overhaul and whether to retain stand-by units.The usefulness of the pseudo-operations research technique known as Replacement Theory is more readily re-cognized by the maintenance engineers in mining and other heavy industries. One of the least complex models enables the optimum Lifetime of an asset to be determined."

Jan 1, 1970

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By N. Afrin

The microstructure and tensile properties of AZ31B-H24 magnesium (Mg) alloy after friction stir welding (FSW) were evaluated. The grain size was observed to increase from approximately 5 µm to about 9 µm after FSW. The obtained Hall-Petch type relationship showed a strong grain size dependence of the hardness values. While the FSW led to about half of the yield strength of the base magnesium alloy, the ultimate tensile strength after FSW could reach about two thirds of that of the base alloy. The hardening capacity of the FSWed samples was about twice of that of the base alloy. The strain hardening exponent of the base alloy was found to be about 0.1 whereas it became larger than 0.3 for the FSWed samples. After yielding the base alloy showed a high initial and almost constant work hardening rate, corresponding to linear hardening stage II, followed by stage III with a decreasing hardening rate. Stage II linear hardening was observed to be absent in the FSWed samples.

Jan 1, 2007

By J. S. Edwards

The ISASMELT? process is recognized worldwide as a modem, flexible, environmentally-friendly and low capital cost smelting technology. Due to the inherent simplicity, and the advanced process control that has been developed, personnel become competent within weeks of being introduced to the ISASMELT? technology. This compares with the years required to become proficient with alternative technologies. Copper smelters in Australia, USA, India, China, Peru and Zambia have installed ISASMELT? technology under licence from Xstrata Technology. In the secondary copper business, plants in Belgium and Germany are processing copper and/or lead materials in ISASMELT? furnaces in a two stage process. In a single furnace smelting is followed by converting. Both plants have exceeded design capacities and are continuously improving their performance. The next evolutionary step for the technology is the implementation of the continuous copper converting process on a commercial scale. The present work describes the design status of the continuous converting process - ISACONVERT?.

Jan 1, 2007

By K. U. Kainer

Magnesium and its alloys as the lightest available construction metal offer a wide range of opportunities for the usage in transportation industries, especially Magnesium wrought alloys with their improved mechanical properties show a high potential for structural applications, While magnesium cast components have found their application the interest is now spreading to wrought alloys due to the possibility to get even more homogeneous and better properties compared to cast parts, Therefore alloy and process development especially for extruded and sheet material is a main concern to enhance the application of Magnesium wrought alloys, Castings are still form the majority of applications of magnesium alloys, although efforts to develop adequate wrought alloys have increased, In the presentation, the alloy requirements for processing of cast and wrought alloys will be discussed, The various processing routes and alloy compositions result in specific microstructures and properties which determine the potential use of these alloys, Today, the spectrum of available alloys covers standard alloys as well as alloys for use at elevated temperatures, The trend will be to further diversify the alloy compositions and to improve the alloy properties, Areas of concern still remain the wrought processing and the high temperature (creep) and corrosion properties of magnesium alloys, Examples of recent developments in these sectors will be given, The presentation will also provide an overview of the historical and current use of magnesium and an outlook on future applications.

Jan 1, 2006

By H. D. B. Wilson, W C. Brisbin

The Thompson-Moak Lake nickel belt lies along the root of a Precambrian mountain range of the island-arc or alpine type. This range coin-. cides with the boundary between the Superior and Churchill blocks of the Canadian Precambrian shield. The nickeliferous peridotites and nickel ores occur along a negative gravity strip, which also coincides with strong thrust faulting and the axis of greatest deformation of the mountain range. Similar structures and highly nickeliferous peridotites occur in present-day island arcs. Much of the belt is covered by Paleozoic rocks, but a length of 270 miles may be explored by present-day methods. Nickel deposits have been located along 60 miles of the belt. The length of the favorable structure and the size of the known deposits suggest that this will be one of the world's major nickel regions. The regional gravity anomalies, which consist of a branching negative strip bordered by two positive strips, are best explained by major warps of a crust consisting of a granitic and basaltic layer. The ore deposit

Jan 1, 1961

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By S. Pauly, U. Kühn, J. Eckert, I. Kaban, G. Wiehl, F. Silze

In the present work, the effect of Ga on the wetting behavior of the Cu-rich braze filler CuGa10 (wt.%) on the steel 304L was investigated. For this, the macroscopic and microscopic effects governing the wetting of pure Ga, pure Cu and CuGa10 alloy (wt.%) on the austenitic steel were analyzed and compared. Contact angle and surface tension measurements were carried out by means of the sessile drop technique and, in addition, the phase formation at the interface was determined. Pure liquid Ga spreads on 304L, which supposedly is related to the formation of intermetallic Fe-Ga phases growing into the liquid Ga. Depending on the annealing time, FeGa3 and Fe14.5Ga12 were identified. In contrast, CuGa10 as well as pure Cu show secondary wetting on the steel surface. Especially, liquid Cu prefers to spread laterally and vertically along the grain boundaries of the steel substrate. In spite of rather similar mechanisms, CuGa10 wets 304L steel at lower rate than pure Cu above the liquidus temperature.

Jan 1, 2014