Search Documents

By C. M. Trigg

"PEC uranium deposit, 100 km southwest of Coppermine, was discovered by diamond drilling in 1976 following ground and airborne geophysical surveys, geological mapping, geochemical surveys and boulder prospecting that were initiated as the result of the discovery of uraniferous sandstone outcrops in 1969 by geologists of Aquitaine Company of Canada Ltd.The deposit is within gently northeasterly dipping medium to coarse-grained Unit 11 quartzitic sandstone of Neohelikian Dismal Lakes Group. The deposit is from 10 m to 70 m above the base of the sandstone which, beneath the deposit, non-conformably overlies weathered and altered Aphebian granite of Great Bear Batholith or unconformably overlies rubble breccia, conglomerate and medium-grained Unit 8 sandstone of Paleohelikian Hornby Bay Group.A northeasterly trending, 500 m wide graben, bounded by the steeply dipping northeasterly striking Imperial and Aquitaine faults, contains the deposit which is 1.1 km long by up to 340 m wide. The deposit overlies a post-Hornby Bay Group, pre-Dismal Lakes Group topographic high. Uranium principally occurs as stratabound, often peneconcordant bands; a lesser amount of uranium is fracture controlled.Stratabound uranium exists in gently easterly dipping, subparallel bands ranging in thickness from 1.5 m to 6.0 m. Pitchblende, coffinite and sooty black uranium oxides occur as interstitial disseminations and grain coatings subparallel to bedding; they also replace pyrite and form narrow veinlets.Small amounts of torbernite, carnotite and cuprosklodowskite coat pitchblende and are disseminated within mineralized bands. Pyrite, marcasite, chalcopyrite, chalcocite, cove/lite, digenite, azurite, malachite, arsenopyrite, glaucodot, niccolite, bravoite (? ), goethite, hematite and magnetite as well as quartz, barite, calcite, biotite, chlorite and clay minerals exist within the mineralized bands. Uranium grades of 0.1 % to 0.3 % U3O8 over thicknesses of 1 m to 2 m are typical.A steeply dipping fracture zone near the Imperial fault contains sooty black uranium oxides, torbernite, carnotite and cuprosklowdowskite as well as sulphides, cobalt arsenides, quartz and carbonate. The zone may reach 70 m long; its true width is about 1.9 m. Uranium grades range up to 5.18% up, over0.9m.Pitchblende and coffinite from PEC deposit have been dated at 1.08 ± .10 Ga with possible remobilization at .45 Ga. The deposit contains an inferred 3,150 tonnes of U3O8."

Jan 1, 1986

By D. Gagnon, B. Dubreuil, J. -M. Lalancette, D. Lemieux

"The pilot scale extraction of gold with a brine of sodium chloride and bromide at 30 ºC, in an atmosphere of halogens at atmospheric pressure, leads to gold chloride with 95% gold recovery. The use of dilute hypohalites (1 – 3%) instead of free halogens, which is strong enough to oxidize hypobromite into bromine, simplifies the recycling of halogens by electrolysis. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable. The Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.INTRODUCTIONThe use of chlorides for the extraction of gold predates the discovery of chlorine by Scheele in 1774. In the Plattner chlorination process (Christy, 1888) sodium chloride and copper salt were used to promote gold recovery by amalgamation with variable results. The introduction of the cyanide technology in 1889 has led to a general use of this method for gold recovery. In the last decades, a return to chlorine in extractive processes has been noted (Ferron, Fleming, O’Kane and Dreisinger, 2002), mostly because of environmental pressure for non-cyanide technologies.This paper describes a closed circuit proprietary approach (Lalancette, 2009) developed and piloted by Nichromet Extraction Inc. for the extraction of precious metals with recycled mixed halogens; chlorine and bromine from hypohalites. DESCRIPTION OF THE PROCESSThe attack of gold by halogens can vary significantly. The rate of reaction is substantially higher with bromine (Br2) than with chlorine (Cl2), by a factor of more than five, although the oxidation potential of Cl2 is higher than Br2, as shown in Equation 1a and Equation 1b (Latimer, 1952)."

Jan 1, 2012

By D. R. Lentz, J. A. Walker

"Abstract -The Flat Landing Brook Zn-Pb-Ag deposit of the Bathurst Mining Camp occurs within a narrow thrust-bound nappe containing felsic volcanic and volcaniclastic rocks of the Tetagouche Group. Within the host nappe, the Tetagouche Group is represented by the Nepisiguit Falls Formation and the overlying Flat Landing Brook Formation. The Nepisiguit Falls Formation is divided into two members: quartz- and quartz-feldspar-phyric volcaniclastic rocks ± minor lavas (Grand Falls member), and aphyric, fine-grained volcaniclastic rocks (Little Falls member). The Flat Landing Brook Formation consists of aphyric rhyolite flows and interbedded pyroclastic rocks. Several gabbroic intrusions occur in both the footwall and hanging-wall sequences. These gabbros locally cut out the mineralized horizon at shallow levels, and are considered to be feeders to tholeiitic basaltic flows (Forty Mile Brook member) of the Flat Landing Brook Formation. The Flat Landing Brook deposit has many of the characteristics typical of volcanogenic massive sulfide deposits occurring within the highly productive Nepisiguit Falls Formation in the eastern part of the Bathurst Mining Camp. Mineralization occurs within or at the top of the Grand Falls member and comprises four or more massive to semi-massive sulfide lenses that vary in thickness between 3 and 5 m. Massive lenses are laterally gradational to, or underlain by, zones of disseminated sulfides up to 38 m thick. The deposit contains an estimated resource of 1.7 Mt grading 4.9% Zn, 0.94% Pb, and 19.54 g/t Ag to a depth of approximately 150 m. From 150 to 300 m below surface, mineralization is low grade and mostly disseminated. However, below 300 m, ore-grade (>10% Pb+Zn) massive sulfide lenses have been intersected over mineable widths. Oxide facies iron formation overlies and (or) grades laterally into the sulfide lenses. The oxide facies has strong positive Eu anomalies and gently sloping rare earth element (REE) profiles suggesting that it was formed from relatively hot acidic fluids that had interacted with felsic volcanic rocks in the footwall. In contrast, the silicate facies iron formation that is more distal to sulfide accumulations has very weak positive Eu anomalies and gently sloping REE profiles, suggesting either cooler hydrothermal fluids or dilution of the hydrothermal component by detrital material. Hydrothermal alteration has affected most footwall rocks. Most notably, albite-destructive alteration has resulted in Na2O depletion, whereas mass addition of K2O is manifested in the formation of sericite (white mica). In more intensely altered quartz- and feldspar-phyric volcaniclastic rocks of the Grand Falls member, feldspar destruction is accompanied by chlorite alteration, producing quartz-phyric rocks similar to those in the footwall of many Bathurst Camp deposits."

Jan 1, 2006

By R. D. Lindsay

Pamour Porcupine Mines, Limited has been actively engaged in the ''Custom Tolling'' of Gold-Bearing materials throughout the past decade. Experience acquired in this area was utilized to design and commission a custom gold milling facility at its operations in Timmins, capable of:(a) Accepting a bulk ore test sample at the rate of 150 t/d for crushing, sampling, and metals analysis;(b) Processing gold-bearing ores at a rated capacity of 150 t/d, to produce a goldbearing sulphide concentrate;(c) Processing free milling gold ores at a rated capacity of 80 t/d for total cyanidation;(d) Cyaniding custom gold flotation concentrates at a rated capacity of 80 t/d; and(e) Processing of complex gold/copper or carbonaceous ores, requiring an impurity flotation concentrate separation stage prior to cyanidation, at a rated capacity of 100 t/d.Items considered in the process design and development included:- various gold ore types available for processing;- flowsheet flexibility required;- sampling strategy as related to head grade determination and metals accounting; and- contract considerations.This paper highlights how these various considerations were used to design Pamour's ''Custom Gold Milling Facility''.

Jan 1, 1987

By Sanjiv Dhanjal

"Often mineralogy dictates the physical properties of a material rather than chemistry. This in turn affects how that material behaves in a process plant, and whether optimum conditions for refining one mineral are different to those for refining another. For example how does refining copper from chalcopyrite differ to refining copper from bornite?Minerals are naturally occurring inorganic solids that have a definite chemical composition and an ordered atomic (crystalline) structure. X-ray diffraction is a common and highly developed method to identify and quantify minerals. X-rays are fired onto a material and the mineral is identified by the angles where the diffracted X-rays are in phase.Most X-ray analyzers are laboratory based. A sample is prepared and analyzed by a detector that travels in an arc to collect the diffraction pattern. COSMA has a curved detector which picks up the complete x-ray pattern instantaneously. Therefore, material is collected and transported through the machine where is it is analyzed continuously.COSMA measures about 0.5 tons of material per day, while laboratory analyzers measure a few grams at a time. Real time data trends are produced allowing for improved process evaluation and automatic control. The COSMA on-line system has taken X-ray diffraction out of the laboratory into the field.There are a number of systems in operation in cement production. It is recognized that on-line mineral analysis has a role in many other processes. This paper presents the technology and invites further discussion should the technology be beneficial to members of the audience.INTRODUCTIONThis article describes COSMA, a system that provides direct and continuous on-line mineral analysis using X-ray diffraction in the field. While X-ray diffraction is a common technique used in mineral analysis, the time from sampling to analysis can be hours and plant operators typically do not get the data in time to control a process or respond to an upset. COSMA provides rapid measurement, analysis and feedback of data, in real time. This provides powerful information that can be used to optimize operation, thereby reducing costs and increasing quality."

Jan 1, 2009

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By C. S. Parsons

Introduction Up to the present, the operation of small mills for the treatment of gold ores has not been favoured in Canada to the extent that it has in other countries. For instance, a list of the operating properties in Southern Rhodesia, published in The Rhodesian Mining Journal of November, 1934, shows for the month of September, 1934, that there were over 500 small mills treating less than 50 tons per day, and the majority of these between 5 and 25 tons. They are operated by individuals, syndicates, and small mining companies. It is presumed that the operations are profitable, although from the published figures of the tonnages treated and the yields, it is difficult for one familiar with Canadian operations to understand how this can be possible, in the majority of cases. Most of these small mills employ stamps with plate amalgamation and with, occasionally, tables to produce a concentrate. Enquiries have been received from many parts of the world respecting milling practice suitable for small gold mines and the type of plant used in Canada. The tenor of these enquiries leaves the impression that the majority of the writers assume that the practice would be similar at all small properties. This, of course, is not the case. Conditions vary widely, and what would be a suitable mill for a typical Nova Scotia ore would not necessarily be wholly adaptable to many ores in Ontario, Quebec, or British Columbia. This paper has been written with the intention of inviting discussion, and it is hoped that, by such discussion, the subject will be more fully dealt with than has been possible in the time at the disposal of the writer. Only more or less standard principles and practices have been dealt with, and, purposely, no reference has been made to plants using mills of the Hadsel, the Nutt, or the Gibson type. As there is available but little reliable information on the costs of installation and operation of small mills, it is also hoped that those contributing to the discussion of milling practices for small mines will be in a position to give these data for the benefit of those contemplating the erection of small plants in Canada. Although it is difficult to generalize, it can be said that there are three types of gold mills commonly used at small mines: (1) Amalgamation and Gravity Concentration; (2) Amalgamation and Flotation; and (3) Cyanidation.

Jan 1, 1935

By G. J. Hawkes

"We all know that every man who works for us should have a thorough knowledge and understanding of his responsibilities. But how about ourselves? Du we have a thorough knowledge and understanding of our own responsibilities as Mill Superintendents?I once had an occasion to say to a Manager that I did not know something was my responsibility and he replied with suitable emphasis ""Everything inside those four walls is your responsibility"". That makes the extent of our responsibilities clear but does not give us a check list to keep an eye on as we do our job from day to day.What are our responsibilities? I suggest they are the following:1. Developing and maintaining efficient operating and maintenance crews.2. Milling the required tonnage.3. Recovering the economical maximum amount of gold.4. Keeping costs at the economical minimum.5. Seeing that the figures are reasonably accurate for tonnages, assays, production, losses, and costs.6. Preventing accidents.7. Preventing fires.8. Maintaining the equipment and building and keeping them clean and tidy.9. Enforcing company rules and regulations."

Jan 1, 1965

By Fathi Habashi

The year 1987 marked the centennial of the beginning of modern hydrometallurgy. On October 19, 1887 British Patent No. 14174 entitled Process of Obtaining Gold and Silver from Ores was issued*. The discovery was made by John Steward MacArthur (Fig. 1), a chemist-metallurgist, supported and assisted by Robert and William Forrest, two brothers practicing medicine in Glasgow. The discovery was made in the basement of their clinic. The process, which became known as the cyanidation process in reference to the alkali cyanide reagent used, immediately received industrial success in New Zealand in 1889 and in South Africa in 1890t. It displaced the chlorination method which had been in use. In 1903 MacArthur was awarded the first Medal of the Institution of Mining and Metallurgy in London1131 - The cyanidation process was responsible for the doubling of gold production in the world in the two decades which followed its first application (Fig. 2). To the modern metallurgist, it may be surprising to think of MacArthur coming across an obscure reagent such as an alkali cyanide as a leaching agent for gold ores. It is the purpose of this paper to discuss the background and the factors that led to this invention, the development of the understanding of the process, and the application of modern technology.

Jan 1, 1999

By F. P. Hassani, H. B. Poorooshasb

"A kinematically admissible velocity field is applied to study the arching phenomenon in a cohesionless granular backfill placed between two rough vertical inflexible walls. The study is different from the previous works which are almost entirely based on statically admissible stress fields. It is shown that the development of arches is strongly influenced by the previous loading history of the backfill which controls the nature of the constitutive laws that govern the mode of stress deformation of the backfill. This preliminary study employs simple models in order to show the potential use of such an approach in evaluating and understanding mine backfill behaviour in the underground excavation. The pressure exerted on the floor supporting the backfill is also studied in some detail.INTRODUCTIONAlthough the importance of the design of mine backfill has been discussed extensively by a number of authors, i.e. Hassani et al. (1985), such theories have not as yet been incorporated in design criteria for underground mine backfilling operation . One factor that such theories must incorporate is the so-called arching action .The phenomenon of arching has been the subject of study by many researchers in the field of civil engineering and mining engineering. Among these scholars the works of Terzaghi (1943), Krynine (1945), Lusher and Hoeg (1964) and Handy (1985) are noteworthy. All these authors use a statically admissible stress field as a starting point to develop their theories. The approach taken by the authors of the present paper is completely different because they employ a kinematicallyadmissible velocity field. It is their belief that the arching phenomenon is closely linked to the interlocking of grains as manifested by the degree of dilatation of the granular mass when subjected to a shearing process.This paper is written in the following sequence. To define the interlocking quantitatively it is necessary to state the constitutive law governing the stress deformation characateristics of the granular mass. This is done in the next section as the law proposed by Poorooshasb and Pietruszazck (1985, 1986) is stated and simplified to suit the present analysis. Next the mode of formation of an arch in a simple system consisting of a mass of backfill sandwiched between two vertical rough walls of infinite extent is examined. The velocity field obtained from the above example is used to obtain solutions to two more complicated situations. The first situation assumes that the backfill is supported, in addition to the vertical rough walls, by a Winkler foundation at its base. The second situation assumes that the Winkler foundation has been replaced by a horizontal beam of uniform section and simply supported at its extremities. The findings of the study are summarized and their practical implications discussed in the concluding remarks."

Jan 1, 1989

By Boyd Davis, Vladimiros Papangelakis, Douglass Duffy, Michael Carlos

"The processing of lateritic saprolite in hyper-concentrated magnesium chloride brines offers several potential advantages for the hydrometallurgical production of nickel. An aggressive HCl-MgCl2 leach at atmospheric pressure can significantly reduce magnesium dissolution, and offers the ability to recover HCl and MgO by a less energy intensive process than conventional techniques via the formation of magnesium hydroxychlorides. Inevitably, the high chloride concentration renders iron fully soluble during leaching and thus requires subsequent iron control and disposal steps. Experimental measurements coupled with OLITM modeling were conducted to investigate the behaviour of iron in concentrated magnesium chloride brines, in terms of chemistry (nature of iron species) and solubility limits. The solubility of ferric chloride in magnesium chloride solutions of concentrations and temperatures relevant to this process was controlled by a previously unreported solid phase: 2.5FeCl3·MgCl2·7.5H2O. Iron precipitation tests on synthetic leach solutions without seeding indicate a metastable akaganeite precipitate which transitions to hematite upon equilibration. Magnesium chloride solubility in ferric chloride solutions was also investigated to allow the simulation of a ternary phase diagram for the MgCl2-FeCl3-H2O system, in order to determine process conditions that avoid unwanted chloride precipitation.INTRODUCTION In the search for more economical processes to treat lateritic saprolite for nickel production, chloride hydrometallurgy has been increasingly investigated. While High Pressure Acid Leaching (HPAL) can frequently economically treat lateritic limonite, the presence of saprolite negatively affects process economics. The higher magnesium content of saprolite increases acid consumption, because magnesium sulphate, unlike iron and aluminum sulphates, does not hydrolyze in HPAL. This soluble magnesium decreases the sulphuric acid strength by an amount greater than the amount of acid stoichiometrically required to leach magnesium, which must also be disposed of or recovered (Jankovic, Papangelakis, & Lvov, 2009). Due to these issues, pyrometallurgy is most commonly employed to treat lateritic saprolite, via the Rotary Kiln-Electric Furnace (RKEF) process; this process uses a rotary kiln to dry and partially reduce nickel and iron oxides before sending the calcine to an electric furnace for smelting to produce a ferronickel product for the stainless steel market. Although the problems encountered during hydrometallurgical processing are avoided and nickel recoveries are high, high capital and energy costs prevent the application of this process to lower grade lateritic saprolite deposits (De Bakker, 2011)."

Jan 1, 2016

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By Thomas R. Larson

"Many concentrators use re-circulating “plant” water for dilution in their flotation circuits. However, if crusher dust suppressants, ball mill grinding aids, or even agitator bearing grease are introduced into this water, and the water itself is not subject to cleaning steps, then sufficient quantities of these chemicals may appear in the flotation cells and begin to impact the flotation separation. A bench flotation procedure has been coupled with statistical analysis in order to estimate the impact of small quantities of non-flotation chemicals on flotation performance.INTRODUCTIONCleveland Cliffs produces iron oxide pellets for blast furnace feed, and is developing the capability to produce ferrous metallic products to supply a wider customer base. Cliffs manages five North American iron mines, including the Wabush mine sites in Labrador and Quebec. Based on various characteristics of the ore bodies, the flow sheets of the five mines are diverse. For example, Hibbing Taconite uses magnetic separation alone as their primary upgrading method, but Northshore and Empire use magnetic separation followed by flotation, and Tilden uses flotation alone. Last but not least, the Wabush concentrator upgrades primarily with gravity and electrostatic separation techniques.At Northshore, concentrate from the magnetic separator circuit is fed to a reverse flotation circuit. By design, the magnetic separators operate at the highest possible recovery of magnetite, as the separator tails are discarded, and relatively high silica content was acceptable to Northshore’s customers. As the steel-making industry moved toward lower and lower slag volumes, the silica content in the magnetic separator concentrate became a problem. The flotation step was added in the late 1980s in order to decrease the silica assay of the magnetic separator concentrate to meet the current customer requirements. In this setting, the flotation feed stream contains very little silica that occurs as liberated quartz particles. As the degree of liberation of the flotation feed stream is then a limiting factor for silica removal, the online grind control then was linked to flotation in the overall plant control system so that grind can be adjusted to achieve improved liberation if necessary for the flotation process."

Jan 1, 2002

By Ken Dyck, Chuck Edwards

"Cameco's McArthur River is the world's largest high grade uranium mine. Production started in late 1999. Cameco carried out the engineering design and construction management for the McArthur River project, including all aspects of mining, ore handling and ore transportation. The ore composition was expected to vary dramatically (0 to 30% U3O8; 0 to 25% clay; etc). To cope with the composition swings, sizing screens were selected to provide classification in the grinding circuit. The grinding circuit started up close to the design to provide minus 500 micron slurry. The 50% solids (wt) ground ore slurry proved to be difficult to transport to and process at the Key Lake Mill. Slurry containing high concentrations of high density pitchblende (about spgr 8.0) and low concentration of stabilizing clays, would settle in containers. Ore transport efficiency to Key Lake was found to be unacceptable.A test classification cyclone was installed in the grinding circuit at McArthur River early in 2002. The cyclone operating parameters were not typical, but the cyclone was made to work very successfully. Transportation efficiency to Key Lake increased due to more stable slurry. Preferentially ground (fine) pitchblende particles were easier to leach at Key Lake. The radiation exposure for operators and maintenance personnel to handle the more stable slurry was also reduced.The classification sizing screens were removed from the McArthur River grinding circuit and replaced by permanent classification cyclones late in 2002.INTRODUCTIONThe McArthur River mine and Key Lake mill operations are located in northern Saskatchewan, approximately 650 and 720 kilometres from Saskatoon, respectively. Figure 1 is a location map. McArthur River is the world's largest, high-grade uranium mine, with a production capacity of 18.7 million pounds U3O8 annually. (Rosner and Edwards 1998, Dyck 2000, Jamrozek 2000, Rodgers 2001) Proven and probable reserves are more than 473 million pounds U3O8. McArthur River ore, grading on average 21% U3O8, is milled at Cameco's Key Lake operation, 80 kilometres southwest by road. McArthur River production began in December 1999."

Jan 1, 2004

By Stuart Elliot

Brownfield project portfolios are notoriously hard to manage. Day to day there is a constant stream of changes and challenges within projects and across the whole program. When the budget year is over, we?re often left wondering: did the facilities get what they really needed? Did we get value for the capital that was spent? Did we get all the project control and process improvement that we paid for? Great work has been done over the years by the Project Management Institute, Construction Industry Institute and Independent Project Analysis to identify what leads to project success, develop project delivery systems and equip project leaders to perform better. But is attention to individual projects all we need when the job is to deliver a portfolio of many projects? Let?s work with an analogy for a moment, and say a project is like a car, and a project manager the driver. Why can?t all the projects in the portfolio get home in time for dinner? The answer, of course, is that the commute home is about traffic, not just about cars. The road, the signals and the actions of other drivers affect us in our individual cars. Optimizing traffic flow is not about managing individual cars, it is about creating the conditions that allow all traffic to move as smoothly as possible. When we?re stuck in traffic, it doesn?t really matter that we are skilled drivers who know our exact location and our engine?s vital signs. Success with a brownfield portfolio requires more than the equivalent of driver training and a good GPS in every vehicle. Managing the annual budget requires more than tight management of each project. This is not a suggestion to abandon project management in the brownfield multi-projects world; the idea is to find and apply the right tools for delivering a portfolio. Remember, we want confidence in 3 areas: 1. that the facility is getting what it really needs, when it needs it 2. that we are getting value for money invested in facility modifications and improvements, and 3. that our controls are adding value by guiding our improvement What are those portfolio tools? The job they have to do is distinct from project-level thinking: ? Create a clear and balanced business pull for project ideas ? Maintain a respectable plan for fiscal, resource and business control ? Organize the work into a steady flow ? Manage the nature and timing of value-driven project substitutions and priority changes ? Focus on overall business value added and best use of resources ? Repurpose the projects organization into being the way the facility gets improved

Nov 1, 2011

By Bian Xue, Wu Wenyuan

High quality, mono-dispersed, hollow CeO2 microspheres with high surface area were produced by a spray pyrolysis method at 700oC. CeCl3 was used as the raw material of the process rather than Ce(NO3)3 because the latter is relatively difficult to obtain in industrial quantities. X-ray diffraction and electron microscopy results confirm the high quality synthesis of hollow CeO2 microspheres with narrow size distribution, good mono-disperse, and good reproducibility. The process of the formation of mono-dispersive CeO2 microspheres was investigated by chemical dynamics and a possible mechanism is proposed. This simple method for synthesis of CeO2 microspheres is easily scaled up to fabricate other metal oxide nanostructured materials at industrial scale.

Jan 1, 2014

By Konstantinos Modis

According to recently established theoretical analysis and under certain conditions, a critical sampling density can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results. The objective of this paper is the application of the above theory to the Sesklo clay quarry in Greece, where Heracles General Cement Company had conducted a sampling campaign to estimate its reserves. The structural analysis of Al2O3 values generated a variogram model, from which the critical sampling density was identified. This critical number was by far lower than the existing sampling density. Clay reserves were then estimated using geostatistics and inverse distance squares in different data schemes with variable densities. The results of the comparisons between the various models revealed that, when the sampling density was greater than its critical value, geostatistics and deterministic interpolation gave similar estimations, which is also in agreement to the theory. The optimal sampling grid finally proposed here, will result to significant cost savings in the next drilling program which is now in plan by the company.

Oct 1, 2009

By Rees J. Llewellyn

High chromium white irons can be formulated to provide required combinations of abrasion and erosion wear resistance, toughness and capability to withstand corrosion attack. As a consequence, they are used widely in casting form throughout the mining/mineral processing industry, particularly as components for slurry pumps and also as mill and crusher liners, laminated wear plates in chutes and hoppers and in valves, nozzles and cyclones. Traditional cast chromium molybdenum and high chromium white irons for wear applications are covered in ASTM A532 Classes 11 and 111 and are also available as comparable proprietary alloys. They rely on heat-treated, hypoeutectic microstructures containing a high volume fraction of very hard eutectic/secondary metal carbides and martensite to provide extremely high wear resistance. The ability to increase the carbide volume fraction and hence achieve higher wear resistance, has been limited because of severe casting difficulties encountered when carbon and chromium contents are raised and hypereutectic alloys with structures also containing coarse acicular primary metal carbides are produced. The limitation has been overcome and cast hypereutectic chromium white iron pump components have established themselves in a wide variety of mineral processing service applications. Comparisons will be made between the microstructures and wear test performance data for the various alloy types and details will be provided of the service performance improvements that have been achieved through the use of hypereutectic chromium white irons.

May 1, 2004

By D. Knuutila, G. Goyette, James A. Finch, G. Bartolacci, A. Fortin, Chi Ho Lau, A. Lockhart

"In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in a rougher column flotation cell of 125 m3 is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through a decrease in gas flow rate and/or increasing frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability.INTRODUCTIONMcGill and COREM have over the past two years collaborated in a research and development project to merge gas dispersion parameters, frother analysis (McGill technology), and froth properties (COREM’s imaging system) to study the interactions between the collection zone (pulp) and the cleaning zone (froth). The main goal is to increase knowledge of flotation cell hydrodynamics since it is known to govern the metallurgical performance of the flotation process (Power et al., 2000). In this paper, specific work on developing some relationships between operating conditions and froth stability in a copper flotation circuit is reported.The objective of this work is to study gas dispersion in a large volume flotation column (hydrodynamics) and to measure its impact on the froth. By froth imaging, it is possible to diagnose operational problems on the basis of froth characteristics (Bartolacci et al., 2005a) and consequently, to propose ways of improving process performance by froth analysis (Bartolacci et al., 2005b).Another approach to froth characterization is investigated in this paper. In the same flotation column, a froth stability apparatus (column) was included (Triffet and Cillers, 2004). The mechanical froth stability apparatus is used to link “hard” froth characteristic measurements to “soft” froth characteristic measurements (those obtained by imaging)."

Jan 1, 2008

By J. A. Meech, G. R. Baiden

"A dynamic simulation of a mine-mill complex has been conducted using networked microcomputers (IBM PC/AT and IBM PC/XT). These models allow simultaneous operation of an open pit using shovels and trucks, a primary crusher, and a secondary crushing plant. Each process transmits information via the network, linking all operations together. The effects of blasting, ore quality, equipment utilization and configuration on productivity can be studied either interactively or from a report listing at the end of each shift. Programs are menu driven leading the user through the decisions required in day to day operations. The mine-mill simulator is currently being used as a teaching tool at Queen's University to provide senior mining and mineral processing engineering students with an experience and appreciation for the operating problems across the mine-mill interface. The need for coordination and close communication between the mine and mill can be aptly demonstrated using these models. The simulator could be used to contribute to the training of operating personnel in a real mining operation. INTRODUCTIONThis paper describes a computer simulator that is capable of showing the interactions and operating strategies between a mine and a secondary crushing plant. The simulator uses two models developed at Queen's University; one for open pit mining and the second for secondary crushing. PITSIM is a dynamic shovel/truck haulage model origin2lly developed by P.D.D. Chick (1) and K.G. Fytas (2) to solve shovel/truck scheduling problems. CRUSHSOFT is a dynamic secondary crushing plant model developed by R.J. Tucker (3) and C.A. Harris (4) to study alternative operating and control strategies in a crushing plant."

Jan 1, 1987