Search Documents

By W. G. Miller, J. D. Scott, D. C. Sego

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Jan 1, 2010

By S. Glen

Cyanide management practices on modern gold plants are becoming more onerous, due to environmental pressures, particularly for signatories to the International Cyanide Management Code. Operations are therefore seeking to reduce levels of weak-acid dissociable (WAD) cyanide reporting to spigot discharge as well as to any eventual discharges from the tailings storage facility (TSF). Current gold industry standard processes primarily include the oxidation of cyanide by means of sodium meta-bisulfite (SMBS, or SO2) with air, Caro&apos;s acid (H2SO5) or hydrogen peroxide (H2O2). These processes require the transport and usage of expensive oxidizing reagents, along with the safety and environmental issues associated with these corrosive and toxic chemicals. Maelgwyn Mineral Services (MMS) has developed the MMS CN-DTM process, which utilizes the Aachen ReactorTM, a high-energy mass-transfer superoxygenation system, in conjunction with an activated carbon-based catalyst and no additional reagents, to increase the rate of cyanide oxidation to cyanate, the thermodynamically more stable form. Testwork conducted at the Maelgwyn Australia testwork facility in Perth Australia is described, at both pilot scale and continuous bench-scale, on a sample of tailings effluent obtained from an Australian gold plant. WAD cyanide is demonstrated to be lowered using the MMS CN-DTM process from an influent of 130 mg/L to the required levels for discharge to TSF (<50 mg/L). The continuous test results showed stable operation over three residence time turnovers. The pilot-scale results demonstrated the efficiency of the process at the reasonably large scales required for engineering cost estimation.

Jan 1, 2011

By S. M. Grillo, M. Fiori, R. Bornioli, C. Marini, S. Fadda

The Na-feldspar orebodies in Sardinia occur along structures belonging to a regional ENE-WSW system that developed during the late stages of the Hercynian orogeny, and that was reactived during the Alpine orogeny. The main petrographic facies include granitoids, albitized granitoids, albitites (more or less rich in quartz), and albitites containing Mg minerals. Field observations and petrological and geochemical data point toward a metasomatic origin for the albitite orebodies. Albitization involved depletion of K from K-feldspar and biotite, dissolution of free quartz, and a lowering of Sr/Na2O and CaO/Na2O ratios in the protolith, under conditions of a positive thermal gradient. The absence of later K-metasomatism implies that, during a subsequent decline in temperature, the composition of the albitizing fuids was modified by an influx of meteoric or other waters. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1997

By T. R. Stanley

Introduction The purpose of this paper is to interest mining men in the economic possibilities of sand deposits suitable for modern foundry work. Many members of the profession are constantly travelling over the country and it is felt that some knowledge of the necessary properties of foundry sands will enable these men t0 recognize such deposits. It is the experience of the writer that good sands suitable for the varied work of a foundry, such as that of the Consolidated Mining and Smelting Company, at Trail, are almost impossible to obtain from western Canadian sources. It is hoped that the following discussion may arouse some interest in the search for such sands. Sands are used in foundries for two purposes. The main use is for making moulds suitable for receiving hot metal. The mould must retain the? required shape until the metal has solidified. The second use of sand in the foundry is as an abrasive in sand blasting. This is a relatively minor use, and consequently will not be dealt with in detail. Any coarse sand with a high content of quartz will serve this purpose, but round-grained sands are superior to angular types, because they have not the same tendency to shatter on impact with the casting. Sand plays an extremely important part in the successful production of sound castings. This is more evident today than ever before, due to the greater variety of castings and alloys, each of which requires special sand characteristics. Poor sand is responsible for a great many foundry troubles which formerly were attributed to bad? metal; in fact, one investigator goes so far as to say that ninety per cent of bad castings can be traced directly to the sand. Very little of the vast amount of sand distributed over the earth&apos;s surface is suitable for moulding. It is the purpose of this paper to describe briefly the properties which are essential in good moulding sand. Sand for this work must be able to withstand the wash and hydrostatic pressure of molten metal, and yet be sufficiently porous to allow the gases generated in the mould to escape.

Jan 1, 1935

By J. Bélanger, B. Semlali, M. Grenon

RÉSUMÉ La conception des fosses ainsi que l'évaluation des ressources géologiques et des réserves minières sont désormais réalisées entièrement à l'aide d'outils informatiques spécialisés. Cependant, plusieurs analyses, pourtant essentielles à l'évaluation de la viabilité du projet, sont réalisées en parallèle sans véritable optimisation ni synergie avec l'ensemble des données disponibles. Cet article présente deux approches permettant d'intégrer certains types d'analyses aux modèles de blocs miniers. Ces approches permettent de quantifier la broyabilité du massif rocheux ainsi que d'étudier la stabilité des pentes minières à même les outils d'optimisation et de planification minières. Cette méthode permet dès l'étude de faisabilité d'un projet minier de maximiser les données disponibles, menant ainsi à une approche plus intégrée en conception minière. De plus, ces approches sont flexibles et permettent d'évaluer rapidement plusieurs scénarios, tout en laissant la possibilité de bonifier le modèle et de revoir la conception tout au long du projet minier.

Jan 1, 2010

By Victor Azbe

Introduction Lime enters our daily life in many ways. Our building, chemical, agricultural, sanitary, and industrial endeavours depend on it to such a great extent that it could probably be called the most important inorganic chemical, and the extent to which it is used might be considered an index of industrial development. Industrial limes vary greatly in quality, due to internal structure and other characteristics. They may be good or bad, sensitive or slow to react. While improper manufacture may not greatly alter the appearance of the lime, it may affect its properties considerably and thus its suitability in the many processes in which lime is used. In some of the processes, one kind of lime is wanted, in others another. While the nature of the stone from which it is made has much to do with whether a lime is suitable or not, its burning and hydration are the crux of the matter. Up to not so many years ago, the knowledge of lime burning was rather imperfect and it is only relatively recently that its manufacture is approaching the state of a higher industrial art. This slow development was in part due to lime manufacture being scattered among many small concerns who, independently, either lacked the inclination or could not afford to strive for a higher technical development.

Jan 1, 1946

By Ralph D. Parker

THE subject matter of this paper will be primarily restricted to the metallic mineral industry, which last year was responsible for almost 60 per •Cent of the total value of Canada's mineral production. It has been written that, in the broad sweep of eternal time, sixty years is as transient as a flicker of lightning in a summer night's sky. In the history of mankind and human endeavour, however, six decades can encompass momentous events and far-reaching •circumstances, all of which affect the lives of men and change the destiny of nations. This observation is con-firmed very positively by a study of our Canadian mining history, from either the broad viewpoint of human progress or the more specialized viewpoint of national economy. The past sixty years have witnessed vast changes in the economic importance of mining in this country's affairs, and also in the technology of the industry. Mining has emerged from the days of rule-of-thumb practice and is now taking on the stature of a highly diversified science.

Jan 1, 1962

By A. A. Holland

Introduction The world&apos;s largest known deposits of natural sodium sulphate (Glauber salt), generally termed &apos;alkali &apos; throughout western Canada, are located in the Province of Saskatchewan: reserves are estimated to exceed 200,000,000 tons. These are surface deposits resulting from the recent or present-day natural evaporation of brines, in which respect they are similar to those occurring in certain other parts of the world, as in semi-arid sections of the United States, Russia, Germany and Austria. In some areas, underground deposits formed hundreds of thousands of years ago have been _encountered in drilling, and indications are that they also were formed under arid or semi-arid conditions. The master key to the formation of deposits of natural sodium sulphate, wherever they occur, is a climate, either past or present, under which evaporation exceeds precipitation over a considerable period of time. Commercial development of the Saskatchewan deposits began about thirty years ago. Previously, the demand for sodium sulphate had largely been met by salt cake produced as a by-product in the manufacture of hydrochloric acid from common salt. The rapid increase in the production of Kraft paper and, more recently, the development of synthetic detergent materials, have caused a marked increase in the market for sodium sulphate. This chemical gives the extra toughness to Kraft paper and is used in detergent compositions in proportions as high as 75 per cent. Saskatchewan now has six commercial plants producing natural sodium sulphate. Production from each in the fiscal years 1947 and 1948 is shown in Table I. The newest and latest plant is that of Saskatchewan Minerals, at Chaplin, which 1s designed to produce up to 150,000 tons of salt cake, 98.5 to 99.5 per cent pure, yearly. This is equivalent to about 24 percent of the total United States production of crude commercial salt cake for 1947.

Jan 1, 1949

By S. Luidold, A. Poscher, H. Antrekowitsch

"The rare earth elements (REE) are nowadays mainly used for permanent magnets, catalysts, hydrogen storage alloys in rechargeable batteries, for glasses, ceramics, and polishing agents. Other important areas of application are phosphors in different types of lamps (fluorescent tubes, energy-saving lamps, etc.). These lamps are often collected and treated at their end of life by disintegration and sorting. However, the obtained fine fractions comprise not only REE-containing phosphors but also small amounts of mercury and are therefore disposed till today in special landfills. Due to the enormous price increase of the rare earths during the last two years, a lot of activities started for extracting these elements from secondary resources such as for example phosphors. All recycling concepts for this task mainly work with hydrometallurgical methods. The large number of different compounds in phosphors with sometimes very different behaviors with respect to their solubility in aqueous phases forms a major challenge to achieve good yields as well as acceptable purities of the produced rare earth concentrates by a process with a reasonable number of operation steps. Therefore, this paper gives at first a brief overview about the compounds, used as phosphors and about existing concepts or investigations. It further describes our own process design and the results, obtained on laboratory scale. INTRODUCTIONThe rare earth elements (REE) have a central position in the industrialised world despite their marginal production volume in comparison to common metals such as aluminium, copper, zinc etc., because they are essential for many applications. They often cannot be substituted without a considerable loss on functionality and quality. This group of metals comprise the lanthanoids (f–block elements, lanthanum–lutetium) as well as scandium and yttrium.The estimated world mine production of REE amounted to 133,000 t rare earth oxide equivalent in 2010, whereat China accounted for 130,000 t or 98 % (Cordier, 2012). The European Union (EU-27) imported 23,013 t in 2008 to cover its demand. The figure 1 shows the fraction of the European member states in terms of the total imports of rare earth compounds from outside the EU-27 (Schüler, Buchert, Liu, Dittrich, & Merz, 2011)."

Jan 1, 2012

By N. T. Oo, L. D. Hutton

"The Banora Point Upgrade Project is a 2.5km long six-lane divided freeway in northern New South Wales, Australia. The geology at the project area comprises a volcanic succession of variably weathered basalt flows and agglomerate deposits that reach 48m in thickness and overlie Mesozoic sedimentary rocks. A site specific rock classification system was developed that characterised all the rock units based on the engineering properties governing the rock mass behaviour i.e. intact rock strength and defect characteristics (spacing, aperture, infilling, wall roughness and weathering) irrespective of the geological origin. This approach simplified the design and the on-site verification processes. Based on this classification system, rigorous quantitative statistical assessments of the available geological information including various laboratory and field testing were performed to derive the geotechnical design parameters for various rock classes. These parameters were used to complete geotechnical designs of retaining wall systems. INTRODUCTIONThe Banora Point Upgrade Project is a 2.5km long six-lane divided freeway in northern New South Wales, Australia. The key features include two interchanges, a 300m long viaduct, a large cutting through Sexton Hill with an associated 100m wide Land Bridge and retaining walls reaching 490m long and up to 22m high. This paper focuses on the derivation of representative geotechnical parameters for geotechnical design of the retaining structures supporting Sexton Hill Cutting including bored pile retaining walls and soil nail walls. The geology at the project area comprises a volcanic succession of variably weathered basalt flows and agglomerate deposits that reach 48m in thickness and overlie Mesozoic sedimentary rocks. Due to the complex geological nature of the site, an understanding of the regional and local geology, the typical behaviour of individual geological units and the implication of onsite variations from design intention are the ultimate challenges to the geotechnical engineer in order to select representative geotechnical parameters for design."

Jan 1, 2015

By Megan Becker, Aubrey Mainza, Indigo Research Laboratories, Jenny Wiese, Gaynor Yorath, Lucy Little

Particle shape characterisation has an important role to play in mineral processing, to clarify effects of shape on rheology, equipment wear rates, comminution, classification, sizing and flotation. However in industry, shape characterisation is not routine, and the most commonly used shape descriptor in the field (circularity/ angularity/ sphericity) is not invariant. This study aims to investigate shape measurements for a fine particulate ore sample measured with different analytical devices. Two Automated Scanning Electron Microscopy devices with Energy Dispersive X-ray Spectrometry (FEI QEMSCAN® and Zeiss Mineralogic®), and a camera based image-sizer using dynamic image analysis (Retsch CAMSIZER® XT) were compared. Each device was used to analyse the shape characteristics of specific particles in both a coarse sample (–212/+150 µm) and a fine sample (-53 µm) of UG2 platinum ore. Circularity and Roundness frequency distributions obtained from the three devices were then compared. For selected individual particles, circularity showed higher variability than roundness, and the sample circularity distributions obtained by the three devices were completely different. It is clear that circularity data from different studies relying on different devices should not be compared on an absolute scale. The shape parameter roundness was found to be a more robust descriptor than circularity, and it can give a stronger indication of a particulate sample’s shape characteristics on an absolute scale. However, there were still significant differences in the roundness measurements obtained by the CAMSIZER XT and the two Auto-SEM devices, which was attributed to the dissimilar mechanisms of image capture.

Jan 1, 2016

By H. U. Ross

ROASTING is usually thought of as a process in which finely crushed or ground ore is heated with air in a suitable furnace in which the ore is rabbled or agitated in such a way as to insure complete reaction between the oxygen of the air and the oxidisable constituents of the ore. Roasting in this sense is used only to a very limited extent in the iron and steel industry. This is because, in most iron ore deposits mined today, the ore is of a type that does not require roasting. Where this process is used, it is usually because of some special circumstance, such as a peculiar economic condition, that warrants it. If roasting is looked upon in the broader sense as a gas-solid chemical reaction carried out at an elevated temperature in which both gaseous and solid products are formed, then the process is used in the iron and steel industry to a greater extent

Jan 1, 1961

By Arthur Dubé

An account is given of the developments brought about in the last fifteen years by metallurgical research in the field of heat treatment of steels. The practical aspects of these developments are especially emphasized. Methods of representation of the phase-change during austenitizing and sub-critical transformation of austenite are described and the importance of time-temperature-transformation charts for the planning of heat treatment cycles is shown. Special copies such as retained austenite and internal stresses developed on quenching are also discussed in some detail. Due to the interest shown currently in these problems, it has been thought advisable to describe briefly the underlying principles and present some of the results already available.

Jan 1, 1945

By J. D. Clucas, D. B. Dreisinger

"The Starved Acid Leach Technology (SALT) has been developed by Search Minerals to extract nickel and cobalt VALUES (from nickel laterite ores (saprolites) and Caron plant residues. The technology consists of sulfuric acid atmospheric leaching of the ores or residues followed by neutralization and recovery of nickel and cobalt. The acid addition is carefully controlled to maximize nickel and cobalt extraction while minimizing overall consumption of acid by various gangue reactions. The final recovery processes can be tailored for maximum economic benefit. The use of resin-in-pulp processing is advocated as the most cost effective method for initial recovery of nickel and cobalt from lower grade materials. INTRODUCTIONCommercial processes for laterite ore treatment vary according to laterite type and local conditions. The two general categories of laterite ore are saprolites and limonites.Saprolites are generally treated by pyrometallurgical processes for reduction of nickel to matte or ferro nickel alloys. The high cost of drying, chemical reduction and electric furnace smelting requires that the saprolite grade for economic processing is of the order of 1.8% nickel or higher. There are of course large amounts of saprolite that fall below this “cut-off” grade that are not currently economic.Limonites can be treated by the Caron Process which involves drying of the ore, a reduction roast of the whole ore to reduce nickel and cobalt (and some iron) to the metallic state followed by ammonium – ammonium carbonate solution to leach nickel and cobalt. Nickel and cobalt recovery are low (70-85% for Ni and 20-50% for Co). The Caron plant tailings therefore contain high levels of unrecovered nickel and cobalt. Relatively few plants have used the Caron Process and new installations are not anticipated due to the high energy cost of drying and reduction roasting. Nevertheless, plants in Brazil (Niquelandia), Australia (Yabulu) and Cuba continue to operate.The high pressure acid leach (HPAL) process was pioneered at Moa Bay in Cuba in the 1960’s in the treatment of limonites. In the 1990’s the HPAL process was touted to revolutionize the nickel industry with low capital and operating costs for new installations. Murrin Murrin, Cawse and Bulong in Australia were started and in each case the technical difficulties of operating at extreme temperature and pressure conditions and the challenges in “ramping up” a complex hydrometallurgical facility conspired to cause these plants to fail economically. At present, Cawse and Bulong are closed and Murrin Murrin continues to operate after undergoing a financial restructuring."

Jan 1, 2012

By G. M. Behrend

"The mining and processing of mineral ores is a very old industry which is steeped in tradition. Rising demand for metals has recently forced the exploitation of lower-grade orebodies which require extensive beneficiation. The high capital expenditures involved, together with market pressures for high-quality concentrates and pellets, have forced the development of new process technologies which are heavily dependent on automatic process control. Development of suitable instrumentation has been rapid and it is being applied to mining processes today with a high degree of sophistication. The drive for higher efficiency and profitability goes on and has reached a level at which modern digital computers appear to be the only answer. However, the efficient application of a digital process computer is extremely complicated and is therefore approached by the mining industry with considerable hesitation.Some of the benefits promised by the digital computer can be obtained today by other means, which are more manageable and can provide immediate payoff. The result would be a building-block system which would utilize the digital process computer as its final component, to perform true plant optimization, free from routine chores."

Jan 1, 1971

By I. Paredes, R. Díaz, H. Henao

Smelting of copper concentrate generates a significant amount of dusts which are collected in electrostatic precipitators. This material, which is a complex oxide of Cu, Fe, S, As, Sb, Bi and others, is difficult to recirculate into the smelting process due to the reported high concentration of arsenic. However, the dust also has concentration of copper above 10wt %, aside from reported contents of silver corresponding as much as 25wt% of the total inventories of this element in the smelters. Thus, it is of economic and environmental interest the development of a process able to reduce the concentration of arsenic in the dust and produce a material suitable to be recirculated into the smelting process. The present experimental work shows the results of a process of dust sulfidization-oxidition able to remove more than 65wt% of the arsenic present. INTRODUCTION Copper sulfide deposits worldwide exhibit increasing concentrations of arsenic. One case of interest would be the copper ores from the northern zone of Chile, which report high concentrations of enargite (Cu3AsS4) (Revista química, 2015) (Latinominería, 2014). The obtained concentrate from this ore is treated in a Fluidized Bed Roaster, producing calcines with low concentration of arsenic (<0.5 wt% As). This material is suitable to be treated in a Flash Furnace. At the roasting process, the arsenic is volatilized and then precipitated as fine particles of complex oxides. Most of this particulate material is removed from the gas stream through a device called Electrostatic Precipitator (Minería chilena, 2014). The experimental results reported in the literature indicate that arsenic present in these particulate materials (or dusts) cannot be eliminated in oxidizing atmospheres (air) or with inert gases (N2) in a Fluidized Bed Roaster even at temperatures as high as 700°C. There is also information that even the recovery of valuable metals from the dust is difficult through hydrometallurgical processes (private communication). This is how in some foundries these dusts are considered environmental liabilities. Regarding the decomposition of enargite (Cu3AsS4) in neutral atmosphere, it is reported in the literature (Padilla, 2001) that the main chemical reactions are:

Jan 1, 2019

By K. Fagerlund, L. Rosenback, T. Mäkinen, Y. Anjala

This paper deals with the nickel smelter and refinery concepts Outokumpu has applied at Harjavalta and several other plants. Also other process routes and modifications developed and tested by Outokumpu during the recent years are highlighted. Outokumpu started nickel production in Harjavalta in 1959. Until 1995 the Flash Smelting - Peirce-Smith (PS) converting route was applied. High grade nickel matte from the converting step was further refined by means of leaching and electrowinning to produce cathode nickel. In 1995 the nickel production capacity was increased from 17 000 t/a to 52 000 t/a based on the Direct Outokumpu Nickel Smelting Process (DON). In the DON process PS converting is eliminated and high grade nickel matte with low Fe-content is directly produced in the flash smelting furnace (FSF). Metal values from the smelting slag are recovered in the electric furnace (EF) as iron containing Ni-matte. The DON process can be operated with either two matte concept, where high grade FSF matte and EF matte are produced, or a single matte concept, where EF matte is recycled to the smelting furnace and thus only one type of high grade matte is obtained. The additional refinery capacity at Harjavalta is based on hydrogen reduction producing.

Jan 1, 2005

By F Kelly

"A central composite experimental design was used to determine empirical relationships between the operating variables of a ball mill and the characteristics of the ground products. The independent variables selected for the study were the work index and size distribution of the feed material, the feed rate and the pulp density. The measured responses included product size distribution, product surface area, viscosity of pulp discharge, weight of dry solids in mill, mill time constant and emitted sonic vibrations. The ball mill was operated continuously in open circuit during each experimental run.Multivariable regression techniques were used to derive linear empirical models from the experimental results. Of the four factors studied, the grindability of the feed material significantly affected every measured response. The size distribution of the ground product was affected significantly by the feed rate and the size distribution of the feed, but not by the pulp• density. Feed throughput capacity and pulp density were significant to the viscosity of the pulp discharge, the weight of solids in the mill and the mill time constant. Significant first-and second-order models are given for the above relationships. The relation-ships between the characteristics of the sonic vibrations of the operating mill and the various dependent variables have not as yet been established."

Jan 1, 1970

By W. S. Dyer

The Minto coal basin lies in the central part of the province of New Brunswick, near the head of Grand Lake. The village of Minto which is the centre of mining activity of the district, lies about 35 miles east of Fredericton and somewhat greater distances to the north and west of the cities of St. John and Moncton respectively. Although coal has been mined in the basin for a number of years, it was not until recently that the production became sufficient to warrant a thorough geological investigation. The summer of 1922 was spent, in accordance with in structions from the Director of the Geological Survey, in making a detailed study of the geology and coal resources of the Minto coal basin, which is covered by the Minto and Chipman map sheets, each embracing an area of 200 square miles. The present paper is a short outline of the principal results obtained in the field. The writer wishes to acknowledge the assistance cheerfully given him by the managers and officials of the various companies operating in Minto. He wishes especially to thank Mr. W. B. Evans, Manager of the Rothwell Coal Company, for assistance in the collection of fossils and for the generous supply of information relative to the early history of the coal field.

Jan 1, 1924

By Jean Dugas, Roger Sirois

The Mineral Deposits Service of the Quebec Department of Natural Resources is engaged in the preparation of metallogenic maps as a contribution to the Canadian Sub-Committee of the Metallogenic Map of North America. The preliminary work is being done on large-scale maps. The main objective is to clearly represent information on ore deposits in a suggestive way. The design of the legend to meet these requirements is discussed. As these maps are still only descriptive, a further step will be the interpretation of data into metallogenic maps with Jess emphasis on the individual deposits and more on the metallogenic factors. Both types of map should prove useful in the search for ore deposits; the first by providing at once a large amount of information, the second by suggesting the ore controls.

Jan 1, 1967