Search Documents

By P. Talonen

Since the last Iron Control in Hydrometallurgy Symposium in Montreal in 1996, the Kokkola zinc plant has increased its capacity from 175,000 t/y to 280,000 t/y by installing an atmospheric concentrate leaching process, which has also affected iron control in the leaching circuit. Major changes have been made at the jarosite residue pond; a subterranean plastic wall reinforced with bentonite and cement has been built around the pond. A new water collecting system that is used for groundwater level control in the pond area was installed. With these two investments in the pond area, it is now possible to prevent any seepage flow from the pond into the surrounding environment. Water pumped from the residue pond is treated in the water treatment plant. This paper describes the behavior of iron in Kokkola's current leaching processes. The treatment of the jarosite, the improvements to the residue pond and the water treatment process are also described.

Jan 1, 2006

By Pierre Pelletier, Christian Pichetie, Dany Pelletier

"IntroductionDuring 1994, Barrick Gold Corporation, or American Barrick at that period, acquired Lac Minerals Ltd. properties. One of them was the Bousquet Complex. The Bousquet Complex is divided into three distinct sites: one mine (Bousquet 2), one mill (Est-Malartic Division) and one analytical chemistry laboratory (Les Terrains auriferes).The Bousquet 2 orebody was discovered in 1986. An extensive drilling program was initiated during 1987. Its purpose was to define the orebody extent. At the end of 1997, gold production from Bousquet 2 mine reached 1 290 000 oz of gold from a cumulative tonnage processed of 4 175 000 M t.From 1980 to 1990, the Est-Malartic mill was used for the treatment of ore from the following mines: Bousquet 1, Doyon, Francoeur (Richmont mines), Buckshot and 1-20 stope. At present, the mill receives ore from the Bousquet 2 mine.HistoryThe Est-Malartic mill is located close to the town of Malartic in northwestern Quebec. The mill has been in production since the mid-1930s processing mainly clean, free mill gold ore. Active mining from the Est-Malartic mine ceased in 1979 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that it would be economically more attractive to modify the existing Est-Malartic mill than building a new facility on site. The Est-Malartic mill modifications for processing the high-copper/gold ore from the Bousquet 2 mine began in late 1989 and new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leaching circuit continued to operate on the copper flotation tailings with some minor modifications to the solution handling systems. A S02/Air cyanide destruction circuit was also added at that time."

Jan 1, 2000

By David Berberick

"Hecla Limited’s No. 4 Shaft at the Lucky Friday Mine is the largest capital expenditure in the corporation’s 128-year history and is considered the deepest shaft in the United States. This paper will discuss the project’s history and lessons learned from the initial conceptual design work in 2007 through project commissioning in 2017. Change management was key for the owner, contractors, and vendors in delivering the operational and organizational success on the project. The No. 4 Shaft has extended the life of the Lucky Friday Mine by 21 years to 2039. INTRODUCTION The Lucky Friday Mine of Hecla Mining Company (Figure 1) is the oldest active (77 years) and deepest mine in the Coeur d’Alene mining district, producing approximately 725 tonnes (800 tons) per day from narrow, vertical, silver, lead, and zinc veins. Primary access into the mine is via the Silver Shaft, a 5.5-m (18-ft) diameter, concrete lined shaft sunk to an original depth of 1,890-m (6,200-ft). Current production is from the Gold Hunter vein system, approximately 1,525-m (5,000-ft) northwest of the Silver Shaft.Cut and fill stoping is currently employed at depths to 2.3 km (7,500 ft) below ground surface, making it one of the deepest mines in the western hemisphere. No. 4 Shaft is a 5.5-metre (18-foot) diameter, concrete lined circular shaft, constructed as a 1.2 km (3,860 feet) deep winze in the Lucky Friday Mine. The 2.4 m (8 ft.) diameter, double drum, double clutch, Siemag hoist and associated headworks are situated at the 4760 level, top station at 4940 and shaft stations at 5900, 6500, 6580, 7500, 7580, 8300, 8380, 8500, and 8620. Shaft stations reference depth below Silver Shaft top station. The 4 Shaft was designed, constructed and commissioned over ten years, between 2007 and 2017. Basic design work was completed by Nordmin Engineering, followed by detailed design completed by Cementation Canada. Shaft construction was awarded to Cementation USA and lateral development was initiated in early 2008. Over the course of the next nine years, the project was suspended and restarted twice, dealt with the loss of a miner, added scope including shaft depth and mine infrastructure facilities, experienced squeezing ground that required liner replacement, changed excavation section, and dealt with a final alignment that was not within design requirement for verticality. Hecla and Cementation were successful in delivering a facility that provides fully functional access from collar at 4940 level to shaft bottom at the 8620 level. Two active mining levels below the collar, 5900 and 6500 are accessed. In addition, the shaft provides access to the future mining level at 7500, skip loading facility at 7580 level, station and loading pocket cutouts at 8300 and 8380 levels, spill pocket at 8500 level, and shaft bottom pumping facility at 8620 level (Figure 2)."

Jan 1, 2019

By I. Ruiz Bustinza, L. F. Verdeja, Daniel Sbarbaro, R. Parra, J. Mochón

The oxidation of sulfides is a complex process involving gaseous products and intermediate species given rise to emission and absorption spectra which carry out important information about the reaction process. This information could be used for on line monitoring of pyrometallurgical reactor if the appropriate sensors were available. We present in this paper an analysis of the concept that has been successfully applied in iron and steel making industry, as well on fuel combustion control, where the spectra measurement gives the possibility for online monitoring and automatic control of high temperature processes. This concept has not been widely applied in the nonferrous pyrometallurgical primary production. The design of new sensors is discussed from the analysis of spectra measurements during flash combustion of copper concentrates at laboratory scale.

Jan 1, 2015

By K. Webb, M. Hohn

"This paper reviews the evolving Ontario mining regime for mining industry-Aboriginal engagement and its apparent alignment with court decisions, domestic law, emerging international norms, mining industry rules, and mining firm-Aboriginal agreements, drawing on publicly available commentary from government officials, the private sector, and Indigenous communities. This paper provides a preliminary analysis of the potential implications of the new regime, especially for the mining industry and Aboriginal communities and, on that basis, discusses possible future developments.RÉSUMÉ Le présent article analyse le régime minier de l’Ontario pour l’engagement entre l’industrie minière et les Autochtones et son harmonisation avec les décisions des tribunaux, le droit interne, les nouvelles normes internationales, les règles de l’industrie minière et les ententes compagnies minières- Autochtones en se basant sur des commentaires, disponibles publiquement, d’officiels gouvernementaux, du secteur privé et des communautés autochtones. Cet article fournit une analyse préliminaire des implications potentielles du nouveau régime, surtout pour l’industrie minière et les communautés autochtones et, en s’appuyant sur ces données, il traite des futurs développements possibles."

Jan 1, 2016

By F. D. Aaring

"IntroductionTHE PINCHER CREEK gas condensate field, in Township 3, Range 28, and Townships 3 and 4, Range 29, West of the Fourth Meridian, was discovered in 1947 by the Canadian Gulf Oil Company with the completion of Pincher Creek No. 1 well in the Madison lime-stone of Mississippian age.This discovery was the result of a great deal of detailed seismic work in the area and is a credit to the geophysical personnel of the Company. The depth of the reservoir varies from 7,400 feet to 8,200 feet subsea, with the established water level at -8,200 feet. The predicted depth was but a scant 100 feet from that found in the discovery well, at 11, 705 feet. Since the discovery of the reservoir, three additional wells have penetrated the Madison limestone and have further verified the original •seismic interpretation of the limits of this reservoir.To date, •only a very small amount of gas has been produced from this field. Consequently, the reservoir studies that have been made so far are predominantly based on investigations of the phase behaviour of the fluid and physical characteristics of the reservoir rock. In view of the above limitations, it has been necessary to set up and perform model reservoir studies with the fluids and to recover as much core from the productive Madison limestone as possible in order that it might be analysed by conventional laboratory technique and be subjected to detailed microscopic geological examination."

Jan 1, 1952

By Gary Hawthorn

"Laboratory testing, by Lakefield Research determined that, in spite of the relatively high pyrite content of the Golden Rose (GR) orebody, it would respond well to gravity concentration followed by either direct cyanidation or cyanidation of a flotation concentrate.Economics favoured the former choice which became the adopted process flowsheet.During the latter stage of the feasibility study, the Dekalb 500 tpd copper flotation mill became available in the Highland Valley of British Columbia. This plant was purchased by Emerald Lake Resources, and was moved to the Golden Rose minesite.The crushing and grinding circuit were retained and the original flotation circuit was replaced with a 400 mtd gravity plus cyanidation circuit. The plant commissioning commenced in August 1987, and by early September was processing 300 tpd.HistoryThe Golden Rose Mine was operated by Cominco during the period 1935 to 1941 processing 146000 tons grading DAD oz/t Au at a rate of 110 tpd .The process flowsheet consisted of gravity plus amalgamation followed by cyanidation.Metallurgical TestingThe underground mining areas were below the level of Emerald Lake, and had flooded on abandonment in 1942.Samples for metallurgical testing were collected from exposed faces underground once the mine had been dewateredin 1984.In spite of the anticipated high pyrite content of the ore samples, it was apparent from the success of the previous operation that the pyrite did not interfere with the gold recovery.Laboratory testing, at Lakefield, determined that, from a technical perspective, two metallurgical options existed, as shown in Tables I and 2.Note that the very high pyrite content of the ore precluded the possible direct marketing of concentrate. The process flowsheet, therefore, had to contain a cyanidation circuit for the operation to succeed financially.Although the anticipated metallurgy was excellent with either option, the 2.1 % increase in gold recovery with the gravity plus cyanidation option made this the clear choice."

Jan 1, 1989

By O. Herstad, J. M. Toguri, K. Grjotheim

DURING the last three years, investigations on the aluminum reduction of magnesium-bearing compounds have been initiated at the Institute of Inorganic Chemistry, The Technical University of Norway. The results of these investigations are reported in this paper. Very little information exists in the literature on the reaction between magnesium compounds and metallic aluminum. The available information itself is conflicting, and, to clarify the existing discrepancy, the reactions between aluminum and magnesium oxide (MgO), caJcined dolomite (CaO . MgO) and olivine (Mg2SiO.) were studied. The logical approach for the study of these reactions between condensed states with the formation of a gaseous phase is, ( 1) the measurement of the equilibrium vapour pressure of the gas, in this case magnesium, associated with the respective reactions and, (2) the identification of the end products of the reaction in order to establish the re-action scheme.

Jan 1, 1962

By L. E. Djingheuzian

"IntroductionIN 1940, in a series of articles, M. W. von Bernewitz(l) reviewed in detail roasting of gold and silver sulphide ores and concentrates. Since that time some significant developments in roasting have taken place, and a number of papers have appeared in the Canadian technical literature, dealing severally with the roasting of a particular ore or concentrate.The purpose of this paper is not only to review some of these Canadian papers and bring the information on Canadian roasting practices to .date, but also to analyse the mechanism of roasting. Hence, it is proposed to start with a study of physico-cl1emical factors fundamental in roasting, the knowledge of which, by creating a sound basis for a proper roaster design, makes good roasting possible.Physico-Chemical FactorsRoasting can be defined as heating sulphide ores in presence of air below fusion points of the constituent minerals, at such temperatures as to convert metallic sulphides to oxides. Hence, roasting is a chemical process.The object of roasting is, by changing, chemically, mineral constituents of sulphide ores, to make the economic recovery of the desired •Constituent metal by a subsequent standard treatment possible. For instance, pyritic ores, containing gold in sub-microscopic form which no amount of grinding would release, are roasted in order, by oxidizing the sulphides, to open up their structures to such an extent as to enable cyanide solutions to come into contact with the gold and dissolve it. The production of porous calcine is, therefore, the object of roasting of refractory auriferous sulphide ores or concentrates. Such a porous calcine may be defined as a desirable calcine, and the roasts which produce desirable calcines can in their turn be termed desirable roasts."

Jan 1, 1952

By D. Ibarra, J. Jacob, A. G. Guezennec, P. d’Hugues, A. Archane

The lack of adequate gas mass transfer is a rate limiting step in many bacterial leaching processes. Oxygen often becomes a limiting factor because of its low solubility compared to the high demand induced by sulfide oxidation. One way of increasing the solubility of oxygen in water or in media solution is by increasing the driving force, i.e. raising the oxygen partial pressure in the gas stream supplied to the leach pulp. The use of oxygen is a well-known practice in high-temperature bioleaching reactors (above 70°C) whereas air is usually preferred in medium and low-temperature operations in order to avoid too high dissolved oxygen concentrations which could impact negatively the bacterial activity. The purpose of this study was to investigate the use of oxygen-enriched gas in bioleaching reactors at 40°C in order to improve the gas transfer in the system when operating at high solid load (20% and more). Bioleaching experiments were performed on a sulfide-rich tailing waste (pyrite 60%, copper 0.8%, cobalt 0.06 %, gold 1 g/t) using the “BRGM-KCC” bacterial consortia. The reactor used for the tests was designed on the basis of a new bioleaching reactor concept developed by Air Liquide, Milton Roy Mixing and the BRGM which uses floating agitators to inject gases and to mix and to suspend solids in the bioleaching solution. Two types of tests were carried out: with air injection and with oxygen enriched gas mix injection. The aim of this work was to confirm the capacity of bacteria to grow and to dissolve pyrite in this type of bioreactors in oxygenrich atmosphere, and to compare sulfides dissolution rates during both types of bioleaching tests. The results obtained show that the use of oxygen enriched gas mix does not decrease bioleaching performances compared to air injection. High metal extraction yields were achieved (above 80%). No deleterious effect due to oxygen use was observed on the bacteria despite the high level of dissolved oxygen reached in oxygen tests (up to 14 mg.L-1).

Jan 1, 2016

By Gavin A. Hunt

In order for mines to operate profitably throughout their life it is important to monitor and maximise ore recovery. A common problem facing many mines is the underestimation of clay type and its distribution in ore at the mine face, blast hole or in the ore stockpile. Too much clay entering the heap leach ore stream for example causes a dramatic reduction in heap leach efficacy and or increased leaching times. The end result is poor leaching performance and much reduced metal production. Poor clay identification and quantification is attributable to many factors, including costly and slow off-site mineral analysis techniques, such as XRD, XRF and petrology, the visual and subjective limitations of the core logging geologist and a lack of suitable low cost, high throughput mineral logging instruments. To get round these problems a new, non-contact, imaging spectrometer - the SpecCam - was developed by Spectra-Map Ltd, to allow high throughput identification and quantification of minerals from mineable material. Its novel imaging design can collect millions of data points (pixels) per day; each pixel contains spectral information that allows a wide variety of mineral types, including the smectite and illite clays, and phyllosilicates such as talc and kaolin, to be identified. Because all the ore can be imaged a much more reliable mineral log can be made. Hence, mapping changes in mineral composition - related to variations in phenocrysts, macrocrysts, veining or wall rock - is possible. Examples of SpecCam data from Goldfields Cerro Corona Porphyry stockpile and from Rio Tinto?s Argyle Diamond mine illustrate the mineral identification and quantification capabilities of the SpecCam. More importantly, for the first time very accurate % abundances for the different minerals can be obtained using an image-based modal count technique. The modular design of the camera, plus its extremely flexible high speed filter, mean that the SpecCam can be easily installed on different equipment, each one suited to different ore recovery problems. For example the SpecCam can be used on an automated portable logging frame to measure drill core, RC chips, hand samples or powder, or alternatively installed on a Geotek multi-sensor core logger for high-throughput, automated logging of drill or blast hole core using co-registered multi-sensor data. An exciting recent development has been the installation of the SpecCam on CommoDas ore sorting equipment, used around the world for 24 hour mill-feed monitoring and automatic ore sorting. Real-time ore sorting decisions can be made as material is monitored on a conveyor belt running at 3m s-1, from which the ore can be automatically sorted into high-grade, low-grade or waste streams for example. The three installation options for the SpecCam mean that most mineral analysis and automated core logging or ore monitoring needs can be met at the mine. For the first time rapid and automatic mineral identification and accurate quantification can be made. All of which allow the mine geologist or metallurgist to make important decisions about maximising the metal recovery process.

May 1, 2007

By J. A. Brothers, M. R. Foran

"AbstractThis paper reviews the progress made in the manufacture of hydraulic cement from iron blast-furnace slag by simply grinding the granulated material with other constituents. The influence of the chemical and mineralogical composition of the slag, the conditions of granulation, the manner of drying, and the fineness of grinding, on the hydraulic properties of the cement, is discussed. The effect of additions of lime, portland cement, and anhydrite, alone and in combination, on the physical and cementing qualities of the mortar and concrete made from Sydney blast furnace slag, is shown in tables of data and is reviewed in some de- tail. The work at the Nova Scotia Technical College has shown that a cement equivalent in every respect to portland cement can be made from basic blast furnace slag- by the us2 of certain quantities of portland cement as an activator.IntroductionBlast furnace slag is a potentially valuable material for the manufacture of hydraulic cement. It is a by-product of the manufacture of iron in the blast furnace, and is formed by the combination of the silica and alumina .of the iron ore with the limestone flux. The metallurgist terms a slag .acid or •basic according as the percentage of lime is less or greater than the percentage of silica plus alumina. The basic slags have the •more pronounced hydraulic properties."

Jan 1, 1950

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By K. Duckworth

The treatment of Turam data by conventional procedures does not permit the interpreter to make any estimate of induced current magnitudes. This problem may be overcome by using an alternative data treatment procedure. It is shown that the conventional and alternative procedures are equally satisfactory in terms of their ability to provide the location of line currents and estimates of conductor quality. A full description and evaluation of both procedures is presented in conjunction with field examples to show how the alternative procedure may assist interpretation when used to complement the conventional approach.

Jan 1, 1973

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By Patrick S. Hudd

Traditionally in hard rock mining, large diameter raise boring was thought of as 3.04 metre or 3.66 metre diameter holes 300 metres deep. Mine and ventilation engineers were challenged to design systems either incorporating such holes, or slashing and modifying to suit. Now, 5.49 metre diameter holes up to 1,000 metres deep are being excavated. The ability to pilot and ream such holes not only creates new options for mine engineers in mine ventilation system design, but also creates new opportunities in mine access. By combining holes of this diameter with the ability to accurately drill long pilot holes within the diameter of the pilot hole through the entire length of the hole, borehole hoisting systems are now fully capable of being main production or service accesses for mines. This paper will review the present day capabilities of large diameter raise boring, potential applications for such excavations and some considerations for companies contemplating using large diameter raise boring in their operations

Oct 1, 2010

By C Carbonneau

In order to successfully produce columbium pyrochlore concentrates, St. Lawrence Columbium and Metals Corporation had to face two principal problems met in several new operations but possibly made more acute than usual owing to the newness of the project. 1.-The ore is particularly complex, as it is made up of an elaborate intermingling of carbonates and discontinuous ultra-alkaline rock bodies of various ages and types in which no less than seventy mineral have been re-ported. Obvious petrographic or structural controls are lacking. Ore boundaries have to be defined on the basis of assay results and the determination of several minerals which occur in trace amounts. 2.-The pyrochlore concentrates produced had to com-ply with a set of stringent specifications. This fact, combined with the low Cb205 content of the ore, necessitated the use of a beneficiation process that would have to operate at a concentration ratio greater than 100:1. A brief description of the mill circuit is given. Mill stability was obtained through extensive mineralogical study of the mill feed coupled with close geological and engineering control of the mining operations.

Jan 1, 1965

By W. L. Bancroft, Peter Price

"What is now known as the 'Waite section' of the property of Waite Amulet Mines, Limited, was originally the Waite-Ackerman-Montgomery mine. It includes a group of twenty-eight claims lying on either side of the Duprat-Dufresnoy township line, and about 8 miles north-northwest of Noranda, Quebec. ,The original discovery of ore on the property was made by Thomas Montgomery in Block Q, Duprat township, and was staked by him on behalf of himself, I. C. Waite, and C. H. Ackerman, in the summer of 1925. The property was optioned late in 1925 to N. A. Timmins who, after trenching and drilling the deposit, sold his 85 per cent interest to Noranda Mines, Limited. Early in 1927, a company known as Waite-Ackerman-Montgomery Mines, Limited, was formed and shaft sinking and development undertaken. Production commenced in August, 1928, ·and continued tJ May, 1930, when, owing to falling metal prices, shipment of direct smelting ore was stopped. Development of the mine by shaft sinking, drifting, and drilling continued until March, 1932, when owing to the prolonged low price of metals, the property was closed down. In September, 1933, an amalgamation with Amulet Mines, Limited, was effected, the new company being called Waite Amulet Mines, Limited. Early in 1937 operations were resumed, first by direct shipments to the smelter and later by aerial tramway to the Amulet mill. Operations have been continuous up to the present time, reaching an average of 720 tons a day milled for the year 1940. Production during the initial period (1928-1930) amounted to 75,811 tons, having an average grade of 7 .11 per cent copper, 4.47 per cent zinc, and 0.03 oz. gold and 0.65 oz. silver per ton. During the second period (1937 to end of 1946) , 1,060,524 tons, having an average grade of 4.53 per cent copper, 2.97 per cent zinc, and 0.03 oz. gold and 0.65 oz. silver per ton, were produced."

Jan 1, 1954

By H. J. Oterdoom

SMS Group (SMSG) has always been concerned about safety aspects of electric smelter plants for the ferro-alloy and non-ferrous industry. The awareness for safety increased significantly over the past decades and also SMSG contributed with its design features to a safer operation. Today, safety aspects are not only part of the smelter design but also of the overall plant layout. Explosions in electric smelters are rare, but have a huge impact on peoples’ lives, on equipment and on production. For this reason, SMSG wanted to have a better overview of explosions within the smelting industry in order to see if useful statistics could be extracted. Generally, there is a lack of statistics regarding explosions in the electric smelting industry, and not enough information is collected or published. A significant portion of the explosions seems to be water related. Many companies, both operating and engineering, are trying to handle the risks of water, and apply methods to detect water leakages. Installing such a system is a management decision and management has then to make sure the system is properly implemented. The disadvantages and limitations of these systems should be carefully considered and communicated to operators and authorities.

Jan 1, 2015

By F. Baczek, S. S. Rocks, D. Chaiko, T. Walters

The atmospheric leaching of chalcopyrite concentrates using acidic ferric sulfate lixiviants is well known to suffer from slow leach kinetics and poor copper recoveries. A number of approaches have been proposed for improving both leach kinetics and recoveries in this system. Many of these, while effective, suffer from high CAPEX and/or OPEX. As many mine sites begin transitioning from heap leaching of copper oxides to processing of primary copper sulfides, cost-efficient leach processes that are compatible with existing SX/EW processes will be needed to maintain existing cathode production. To this end, FLSmidth is exploring process options and reactor technology for the hydrometallurgical processing of primary sulfides. One approach that appears to be highly effective at increasing copper recoveries takes advantage of the enhanced reactivity of transitory, surface-defect structures generated during particle fracture. Significant process efficiencies are gained by matching the rate of grinding to the rate of electrochemical leaching in Mechano-Chemical leach processes. The patent-pending FLSmidth® ROL process uses a Stirred Media Reactor (SMRt reactor) to achieve copper recoveries of 97+% in 6 hours or less. This approach overcomes many of the surface passivation problems that have hindered other atmospheric leach processes. New insights to leach mechanisms are presented.

Jan 1, 2015