Search Documents

By E. Ghali, A. D. Bas

There is a lack of electrochemical studies of oxidized gold ores since the majority of previous studies were conducted with sulphidic gold ores. In this study, the influence of agitation and iron oxide minerals, i.e. magnetite, hematite, and maghemite on gold leaching was investigated by means of galvanic and passivation phenomena. Cyclic voltammetry studies of Roasted Gold Ore (RGO) in de-aerated electrolyte have shown one oxidation and one reduction reaction while three oxidation and one reduction peaks were observed with gold electrode. Galvanic coupling results by Zero Resistance Ammeter (ZRA) mode indicated that magnetite showed a negative effect on gold dissolution while maghemite and hematite showed a positive effect, relatively, as a result of higher galvanic corrosion rates. Generally, gold dissolution was found to increase in the initial 15 minutes. Increasing agitation speed from 100 to 400 rpm resulted in higher galvanic corrosion rates for RGO, magnetite, and maghemite electrodes, while 250 rpm was found to be optimum for hematite electrode. Passive products such as silver and iron-oxide were identified by XPS and SEM-EDS analysis, respectively.

Jan 1, 2015

By P. R. A. Andrews, I. Jackman

"A mineral processing investigation to recover chromite was performed at Lakefield Research, under the guidance of CANMET personnel, on a 70 tonne ore sample from the Bird River deposit in Manitoba. In the laboratory phase a flowsheet was developed which involved grinding, gravity separation and flotation. The gravity concentrates were upgraded by magnetic separation and the flotation concentrates by gravity concentration . Pre-concentration by electronic ore sorting, magnetic separation and heavy media separation also was examined.The developed flowsheet was applied on a pilot-plant scale in the second phase of the testwork to the ore as received, and to ore pre-concentrated by electronic ore sorting and magnetic separation. Ore pre-concentrated by heavy-media separation was treated on a laboratory scale based on the pilot-plant flowsheet ,Processing the are as received resulted I n 77% recovery of chromite in a concentrate analyzing 30% Cr20 J; processing are pre-concentrated by electronic are sorting resulted in 64% recovery of chromite in a concentrate analyzing 30.5% Cr20J."

Jan 1, 1988

By Stephan I. Zajac, Roger A. Blais, John B. Stubbins

THE iron deposits of central Labrador occur within a relatively small area, herein called the Knob Lake Iron Range, in which a northwest-trending series of low hills and ridges defines the height-of-land at the boundary between provinces of Quebec and Newfound-land. Approximately two-thirds of the deposits are in Quebec and the remainder in Labrador, with several deposits straddling the inter-provincial boundary. These deposits are being exploited in open-pit mines by the Iron Ore Company of Canada centered at Schefferville, Quebec. Since 1954 this company has produced more than 56 million tons of iron ore to become Canada's leading iron ore producer. With indicated reserves of more than 375 million tons of direct-shipping ore and large tonnages of iron formation amenable to beneficiation, this mining district is assured of a long life. This paper describes the Knob Lake iron ores and their geological settings and stresses the features that lead to a better understanding of their origin. The

Jan 1, 1961

By J. T. Vehkala, S. S. Kerr, D. E. Robertson

"Since the late 1970s, extensive work has been carried out at Placer Dome Inc. 's Dome Mine to develop new mining methods and equipment to improve the productivity of narrow vein mining (Mining Magazine, Oct. 1986, pp. 308-317; Mar. 1988, pp. 176-/79). This work has been focused on mining veintype deposits varying from 0.9 m to 1.5 m in width using open stoping and cut-and-fill mining methods.In 1989, the Dome Mine entered into a contract with Ram Raising Ltd., a joint venture company of Angus Martin and I.S. Redpath Ltd., to develop and mine a narrow vein test stope using an Alimak Raise Climber. Early results have been favourable, indicating that Alimak methods can be used successfully to mine narrow vein are.HistoryThe Dome Mine, which has been in continuous operation since 1910, is located in South Porcupine, part of the city of Timmins, Ontario. The mine is wholly-owned and operated by Placer Dome Inc. and is part of Placer Dome Inc.'s international stable of of 19 mines."

Jan 1, 1990

By A. Dahi Taleghani, Amir Shojaei

A continuum damage mechanics (CDM) based constitutive model has been developed to describe elastic, plastic and damage behavior of rock during drilling. In addition to inelastic deformations, this model incorporates rock anisotropies like toughness anisotropy due to the bedding planes orientation that is a common observation in soft Shales. The pressure sensitive inelastic deformation of porous rocks together with their damage mechanisms are studied for drained and undrained conditions. Fracture mechanics of microcrack and micro-void nucleation and their coalescence are incorporated into the formulation of the CDM models to accurately capture different rock failure modes. The performance of the developed elastoplastic and CDM models are compared with the available single cutter test data of a specific shale play and then the models are introduced into a commercial finite element package through user-defined subroutines. A workflow to derive the required model parameters is presented through inverse modelling of the single cutter test data. The developed CDM model outperforms the traditional discrete element and fracture mechanics approaches by removing stress singularities at the fracture tips and simulation of progressive fractures like formation of the cuttings ribbon without any essential need for remeshing. This model would provide a robust tool for modeling bit performance and rate of penetration using conventional elements of FEA with a reliable results and a computational cost less than similar computational techniques like discrete element methods.

Jan 1, 2015

By Getu F. Biftu

There is general agreement among scientists that global surface temperatures have been increasing during the past decades. The increase in temperature is postulated to be the result of either an increase in greenhouse gases emission or climate variability (i.e., due to variations in sun or volcanic activity or El Nino and La Nina events) during past decades and may continue to increase. The effects of a predicted rise in the Earth?s surface temperature include an increase in average global evaporation and increase or decrease in precipitation (Bloomfield, 1992; Mann et al., 1991; Vinnikov et al., 1990; Gan 1995; Zhang et al., 2000a). The general circulation models (GCMs) project a global warming due to greenhouse effects of 1.5-4.5°C by the mid 2050s, with the most pronounced changes taking place in northern latitudes (Nicholls et al., 1996). However, similar predictions at a watershed scale or even a regional scale using GCMs are mot possible yet (Arnell et. al., 1996; Georgievskii et. al., 1996; Zhang et al., 2000a). Detection of historic trends, changes and variability in climatic variables is another indirect means of understanding potential future changes or variability at regional and local scales. The main objective of this paper is to review studies related to climatic change or variability and associated hydrologic changes at a regional scale and local scale, particularly those studies applicable to the Oil Sands Region (OSR) of Alberta. This paper identifies gaps in our current understanding of the hydrologic processes that may be affected by climate change; it discusses potential implications to developments in the OSR; and it explores mitigation opportunities including several that have already been implemented.

May 1, 2004

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015

By Jim Cooney

Background ?1990s saw massive changes in South African mining industry ?over 100,000 jobs lost as the industry restructured; ?1999 ?Placer Dome purchased a 50% interest in South Deep (WAL), a mine located just outside Johannesburg ?This was the first major post-apartheid foreign investment in the South African mining industry The Situation ?Placer Dome decided to lay off 2560 mineworkers (one third of the workforce) from the South Deep Mine to restore the mine to economic viability. ?Unemployment in South Africa was over 25%, and the retrenched mineworkers had few skills with which to make a living. Policy Context ?Placer Dome was committed to: ?global corporate policy of Sustainable Development, ?demonstrating that its business contributes to the economic and social progress of host jurisdictions. ?Government of South Africa was committed to ?attracting foreign investment to its mining sector with a view to modernizing and enhancing its economic and social viability, ?ameliorating the negative social consequences of structural change without arresting the necessary process of restructuring. ?National Union of Mineworkers was committed to: ?working with the mining industry and the government in implementing a Code of Good Practice on Dismissals and a Social Plan to assist retrenched mineworkers (1999).

May 1, 2006

By A. Navarra, C. Arrancibia, R. Yañez, C. Acuña, F. Valenzuela

"Discrete event simulation (DES) is a suitable framework to evaluate and optimize the dynamics of sulphide smelters. In particular, iron-nickel-copper-cobalt sulphides undergo continual oxidation within a roasting or smelting operation, followed by batch oxidation within the converting operation, thus producing iron-free Bessemer matte (or blister copper, in the case of copper smelters); this semi-finished product undergoes further processing to produce nickel, copper and cobalt products, and to recover precious metals. The juncture between continuous smelting and batch converting is often an appropriate focus for the earliest phases of DES development, since it is typically a major bottleneck within nickel and copper smelters; later phases may include increasing levels of detail for auxiliary unit operations, as well as plant logistics. Moreover, DES can support matte-slag chemistry, including Gibbs free energy balances to determine the iron speciation within the slag. DES is therefore capable of linking the fundamentals of oxidation reactions to the intricacies of plant dynamics.INTRODUCTION Discrete event simulation (DES) is gaining acceptance within the extractive metallurgy community, as a technique that quantifies the system-wide performance of metallurgical plants under conditions of uncertainty (Wheeler & McGinty, 2015). In particular, over 90% of smelters that process nickel-copper-cobalt sulphides and copper sulphides exhibit similar semi-continuous dynamics (Crundwell et al., 2011b; Schlesinger et al., 2011b), in which the converting aisle produces batches of material that are sent for further processing (Figure 1). Thus the tools and practices that are developed for a specific sulphide smelter are often relevant to numerous other smelters.The juncture between continuous smelting and batch converting has long been a focus for discrete event simulation (Welgama et al., 1996). Nonetheless, the broad acceptance of DES in nonferrous smelters has been hindered by interdisciplinary barriers that divide industrial and metallurgical engineers (Navarra et al., 2016; Noorossana et al., 2012); this divide has been less severe in steel plants (Hollocks, 2006). In recent years, DES has been used in copper smelters to analyze crane-and-ladle motions (Coursol et al., 2009a), reverts production and consumption (Noorossana et al., 2012), and innovative control systems (Herrera et al., 2016); additionally, DES models have accounted for shutdowns and random breakdowns to provide realistic assessments of copper smelter capacities, thus guiding equipment upgrades (Campbell et al., 2013; Coursol et al., 2009a). All of these studies feature a Peirce-Smith converting aisle similar to Figure 1 that, under normal operations, constrain the smelter throughput, and are thus a bottleneck (Campbell et al., 2013; Navarra et al., 2016)."

Jan 1, 2017

By T. R. Skerry, H. P. Hudson, T. E. Warren

"ALTHOUGH coal is generally the cheapest fuel on the basis of heating value it has been at a disadvantage in competition with other fuels because means have not been available for efficient •Conversion of its thermal energy to mechanical work. Taking the •railway application •as an example, the cost of Diesel oil is about three times that of its thermal equivalent in coal, but the overall efficiency of a Diesel locomotive is about five times that of a coal-fired steam locomotive. Accordingly, the Canadian railways are replacing all coal-fired steam Locomotives, as they are retired from service, with Diesel units. This conversion in itself represents a major loss to the coal industry because the value of railway fuel is approximately 130 million dollars per year, and there are other applications in the medium power range where oil is displacing coal. There is, therefore, a strong incentive to attempt development of an efficient coal-burning engine.Coal has never been a promising fuel for reciprocating internal combustion engines because of the time required for its combustion in pulverized form . This is not less than one-tenth of a second so that the speed of such an engine would have to be very slow. There are also serious difficulties of a mechanical nature arising from the necessity for intermittent combustion and the use of close-fitting pistons."

Jan 1, 1952

By I. I. Betcherman

INTRODUCTION A DISTILLATION process offers one of the most effective methods of refining metals. Its use is particularly attractive in the case of reactive metals which are not readily treated by pyrometallurgical or electrolytic methods. The 1ow vapour pressure of most metals severely restricts the applicability of the disti1lation process and only one or two metals may be effectively treated under atmospheric pressure at a reasonable temperature. If operations are carried out under reduced pressure several additional metals may be effectively distilled. Table I shows the vapour pressure of a number of metals together with a value of the free energy of formation of their ?oxides. Zinc and cadmium head the list and for many years? they have .been effectively refined by distillation. Sodium, magnesium, and calcium follow in descending order, and they may be distilled readily in vacuo and with difficulty at atmospheric pressure. Sodium, which is not of great metallurgical interest, is not considered. Magnesium has recently been produced in considerable tonnages by distillation methods ( 3). This paper describes the vacuum distillation of magnesium and calcium, their separation from each other, and their separation from less volatile impurities.

Jan 1, 1951

By Cheryl Devine, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg

The microbial-mediated recovery of valuable metals locked in mining wastes presents an economical alternative to conventional hydrometallurgical processes. The present study investigated the bioleaching response of a low-grade nickeliferous pyrrhotite tailings (0.6 wt% Ni) and an upgraded pyrrhotite tailings (1 wt% Ni) produced by Vale Base Metals in the Sudbury Basin of Ontario, with the ultimate aim of maximizing Ni recovery. The initial part of the study focused on the bacterial adaptive evolution protocol, by repeatedly sub-culturing an indigenous culture from an acid mine drainage site on 2% (w/v) pyrrhotite tailings. The results showed that the extent of Ni dissolution is positively correlated with microbial activity. Microbial profiling revealed A. ferroxidans to be the dominant member of the microbial consortium. The enriched culture was used for optimizing the growth medium by varying the concentration of essential growth nutrients. Finally, an aerated biotic and abiotic leach of a 10% (w/v) upgraded pyrrhotite tailings with and without pH control, showed a higher recovery of Ni in the pH controlled experiments. These results demonstrate that a high concentration of the oxidant Fe3+ in solution promotes the dissolution of Ni. Furthermore, the sulphide conversion into So was found to be higher in the pH controlled experiments (32%), relative to the experiment without pH control (10%).

Jan 1, 2015

By Ahmad Ghahremaninezhad, Denver H. Cowan

Much of today’s gold is locked within sulphide minerals. These sulphide minerals, including pyrite, need to be subjected to oxidative pre-treatment in order to leach the refractory-gold using traditional methods. Typically autoclaves employing high temperatures between 180?225 ºC, and extremely high pressures between 1,500?3,200 kPa, are used for the oxidative pre-treatment. However, the autoclaves themselves are very expensive, costly to operate and maintain, and produce excess sulphuric acid. This paper studies the atmospheric oxidation of pyrite in ferric sulphate solutions. In general, pyrite oxidation under atmospheric pressure can result in high elemental sulphur production, i.e. less acid generation. Activated carbon has displayed an ability to catalyze the process, achieving reasonable kinetics. The reaction kinetics were investigated by altering acidity of the leaching solution, temperature, catalyst ratio, sparged oxygen and agitation. A combination of X-ray diffraction, scanning electron microscopy, optical microscopy, X-ray fluorescence, inductively coupled plasma mass spectrometry (ICP-MS), and atomic absorption spectroscopy (AAS) were used to monitor the kinetics of the process and elemental sulphur yield. The purpose of this investigation was to determine optimal operating conditions that maximized kinetics of the atmospheric oxidation while maximizing elemental sulphur yield.

Jan 1, 2015

By R. E. Martin

"The Westerose Leduc (D-3) pool, a Devonian reef reservoir situated in Central Alberta, Canada, has now been producing for over seven years. As a unit operation, the pool pro-vides an interesting example of the full exploitation of gravity segregation tendencies. The reef has a 238-foot oil column, underlain •by bottom water and over-lain by a substantial gas cap. The original hydrocarbons in place were 147.96 million STB oil and 94.4 MMMCF of Taw gas cap gas. Nine-teen producing wells on 80-acre spacing have been completed, most of which are highly productive. Gas injection operations return solution gas to the gas cap. A study of the rock and fluid properties of the pool show it to be conducive to production by gravity segregation at high rates. Monthly average producing rates have varied between 800 B/D and 8,000 B/D and have recently totalled 3,000 BID to 5,000 B /D. Recovery and performance predictions under partial pres-sure maintenance at 10,000 BID indicate an ultimate recovery of 66 per cent of the original oil in place. In the absence of pressure maintenance, recovery would be only slightly less."

Jan 1, 1960

By John C. Taylor

A resource document, prepared for the Royal Commission on the Health and Safety of Workers in Mines, which outlines aspects of occupational health and safety in the Canadian metallurgical industry has been expanded to provide examples of some practical solutions. General process descriptions are provided in conjunction with some of the major potential hazards associated with each step. Emissions to the working environment, particularly around converters, are discussed. Newer metallurgical processes, the role of automation and other advances in the metallurgical industry are described with respect to their impact on the work place. The role of staff and unit employees in providing safe working conditions in the complex metallurgical plant of today is outlined and the need for close cooperation within the human sector emphasized. The technology is available and is being applied to integrate the complex process requirements with realistic regulations to control emissions and provide a safe, healthy environment in metallurgical plants.

Jan 1, 1978

By G. Cailletaud, I. Guillot, D. Larouche, R. Martinez, D. Massinon

The precipitation of Al2Cu particles in a 319 T7 aluminum alloy has been modeled. A theoretical approach enables the concomitant computation of nucleation, growth and coarsening, based on an implicit scheme using the finite differences. The equation of continuity is discretized in time and space in order to obtain a matricial form. The inversion of a tridiagonal matrix allows us to determine the evolution of the size distribution of Al2Cu particles at t + dt. The fluxes of solute in-between the boundaries, as well as the ones at the boundaries, are computed in order to respect the conservation of the mass of the system. The main results of the model are compared to TEM measurements. Simulations provide quantitative features on the impact of the cooling rate on the size distribution of Al2Cu particles in good agreement with the TEM measurements. This metallurgical model is integrated into FEA software in order to perform mechanical computations. This kind of multiscale approach allows new perspectives to be investigated in the process of designing cylinder heads. It enables a more precise prediction of the microstructure, its evolution as a function of continuous cooling rates and its impact on the integrity of the structure.

Jan 1, 2015

By Xian Jian Guo, Lei Li, Hua Wang

Direct smelting of copper concentrate to blister copper has the advantages of energy saving and environmental protection. There has been a lot of effort invested in process development including test work and theoretic analysis in the past half century. However, the process has only been applied commercially to a few smelters that treat chalcocite types of copper concentrate. The main limitation to treating chalcopyrite types of copper concentrate is high copper content in smelting slag and low direct copper recovery. Thus intensive slag cleaning is needed. In this paper, the thermodynamic analysis was mainly carried out for the multiphase equilibrium of direct to blister copper smelting for both chalcopyrite and chalcocite concentrates. The practical problems in direct to blister copper smelting, which are mainly in copper content in slag, are clarified. The operational window of slag composition for different temperatures and oxygen partial pressure for the treatment of chalcocite type concentrates is identified. The process operation optimization for the blending of chalcocite, pyrite and chalcopyrite concentrates was done. INTRODUCTION The extractive metallurgy of copper can be divided into two broad groups of processes, namely, pyrometallurgy and hydrometallurgy, and the former is dominant. About 80% of copper in the world is produced by pyrometallurgy (Christopher et al., 2006). The first stage of conventional copper pyrometallurgy processing is to smelt copper concentrate to copper matte composed of FeS and Cu2S with slagging to remove a proportion of the iron (Gargul, Boryczko, & Bukowska, 2017). The smelting processes include bath and flash smelting. The second stage of the process is to convert copper matte to blister copper. In most cases, the copper matte is converted in Peirce Smith (P-S) converters, which are batch operations (Kubiszewski, 2015). The P-S converting can be divided into two periods, slagging and copper blowing. During slagging period, FeS in copper matte is oxidized to FeO, which reacts with silica flux forming slag. When the iron content in matte is less than 1%, copper begins to oxidize and reduce to form blister copper (Kucharski, Sak, Madej, Wędrychowicz, & Mróz, 2013).

Jan 1, 2019

By M. W. Wadsley

"Physical and chemical property models are widely used in process engineering. There exist, in the published literature, completely empirical models of ''thermodynamic properties"", that is, property models that are not consistent with the laws of thermodynamics. There also exist property models that purport to be thermodynamically consistent but are flawed in their implementation. There are also published property models that are consistent with the laws of thermodynamics but that do not reproduce property values with an acceptable accuracy. A practicing engineer might be asked to assess very different property models for which there are a variety of claims. This paper discusses features of thermodynamic and empirical property models that may assist in their practical evaluation and implementation."

Jan 1, 2005

By M. Sanchez

In the last decades, the Chilean copper mining and metallurgical industry have had to modify their technological processes to meet the environmental regulations implemented by the Chilean government, and also to support the pressure of the public opinion. Thus, air quality standards for sulfur dioxide and particulate matter (primary and secondary), plans for reducing emission of arsenic by the Chilean copper smelters, effluents discharge limits, among others regulations were applied by the environmental agency. Additionally, agreements on cleaner production were carried out by mining sector and government. Now, a draft law on mine closure, and another on environmental mining wastes (abandoned mines) are being discussed by the authorities and the mining sector. In the context, production and environmental impacts in different ways to produce copper in the Chilean mining industry are reviewed and regulatory tendencies as well as abatement technologies today used are exposed and discussed in this presentation. Pyro, hydro and electrometallurgical processes employed and their current effluent and contaminants are presented showing various alternatives of treatment in the copper industry. An update of regulations established in Chile vis a vis copper production, with an especial attention to mine closure are also presented.

Jan 1, 2007

By James McManus

The original analogue instrumentation at Lornex Mining Corporation to optimize the throughput by controlling the power drawn by the semi-autogenous mills was found to be inadequate because of the frequent changes in ore type. Although the trunnion bearing pressure of the mill was a crucial control criterion, it was not utilized in the original control scheme. After several plant tests of different types of analogue controllers were unsuccessful in finding any control equipment suitable for this application, it was concluded that a digital process control computer was required. Computer control strategy to optimize the grinding rate by controlling the power and the bearing pressure of the semi-autogenous mill was developed and a Fox 2 /30 computer made by Foxboro was selected. After six months of experimentation, it was found that the throughput was increased substantially by computer control.

Jan 1, 1978