Search Documents

By The Staff

"IntroductionThe difficulties to be overcome in shaft sinking and development at depth are centred at McIntyre in and around No. 12 shaft. Generally they have been due to increasing pressures and temperatures and to changes in geological structure. This paper describes the difficulties and the measures taken to meet them.No. 12 ShaftEarly in 1932 McIntyre decided to sink an internal shaft from the deepest level, the 3875, to explore and develop known veins extending below that horizon. The location selected was a point 1,500 feet south and 1,000 feet east of No. 11 shaft, the main operating shaft through which the men, ore, and most of the materials are handled Shaft and auxiliary equipment we1e laid out for 3,000 feet, that is to 7,000 feet below the surface. The shaft was to be capable of handling 1,500 tons of ore daily from the lowest level, and was to provide ventilation, compressed air, water, and electric power to service all levels.No. 12 is an internal, vertical shaft extending from the 3875 to the 6825 level and bottoming at 7,007 feet. It is a rectangular, four-compartment shaft, 21 ft. 9¾, in. by 6 ft. 3¾ in. outside the timber (Figure 1).There are two hoisting compartments and one airway compartment, each 4 ft. 10¾ in. by 5 ft. ¾ in. inside dimensions, and a combined manway, pipe, and cable compartment 4 ft. ¼ in. by 5 ft. ¾ in. Levels have been established at 150-foot intervals, pump stations and sumps at 1,000-foot intervals, and. there are two loading pockets, one at the 5525 and the other at the 6900 level.The shaft was sunk in two stages. The first stage, consisting of preparation above the 3875 level and sinking to 5585 feet, was completed by March 31st, 1935. The second stage of deepening the shaft from 5,585 to 7,007 feet was started August lst, 1946, and completed three years later."

Jan 1, 1950

By U. Caliskan, S. Miskovic

Gravity separation is a technique that depends on the difference in density of minerals for their separation. Although this method is one of the oldest separation techniques, it is still preferred in the industry because of its low capital and operating cost while it is environmental-friendly. In this paper, we present a new numerical methodology that can be used to investigate dynamics of dense slurry flows in gravity separation systems. A simple channel with a set of riffles is selected as a test platform in order to observe the effect of the riffle shape on segregation profile of particles with different densities. It is believed that the riffle shape would affect the slurry flow and possibly cause one class of particles to segregate within the riffle zone. The turbulence, as a disturbance effect within the riffle zone, causes heavy particles to displace the light, that is, the heavy particles will be trapped in riffles, while the lighter particles are carried by water to the end of the channel, which is an example to uninterrupted suspension. MP-PIC model in OpenFOAM is used to study the effect of riffle shape and slurry percentage of solids in this simple gravity separator on particle segregation profile of four discrete mineral density classes, which are Quartz/Clay (SG 2.6), Pyrite (SG 4.2), Chalcopyrite (SG 5.1), and Gold (SG 19.32). Gold particles are found to be readily captured and retained in the riffles because of their high density, while particles with the intermediate densities are more influenced by the flow. The developed model framework has been proven robust and capable of providing physical results even for the flows with a very high percentage of solids, characteristic for mineral processing operations. INTRODUCTION Gravity-based ore concentration techniques make use of differences in density of minerals within an ore to enable separation of valuables from the gangue. As some of the oldest techniques used for ore beneficiation, they are known to offer a range of benefits such as low specific energy consumption and low capital and operating costs (Burt, 1999; Falconer, 2003; Holland-Batt, 1998), however, they suffer from low selectivity, poor separation efficiency, and low capacity. Gravity separation techniques are common practices in the mining industry and are employed widely for the precious mineral concentration, iron ore recovery and coal preparation (Kroll-Rabotin, Bourgeois, & Climent, 2013; Laplante & Spiller, 2002; Williams, 1997). For example, gravity separation systems are highly applicable for precious metal enrichment operations by being included in primary grinding circuits, shaking table tailing separation, pre-concentration of leach feed and flotation concentrate enrichment for both flash and conventional flotation purposes (Burt, 1999; Falconer, 2003; Holland-Batt, 1998; Laplante & Spiller, 2002; McAlister, 1992). Gravity separation can be employed in the copper processing circuits by being integrated into the pre-flotation circuit to capture the gravity recoverable gold (GRG) and any free copper aiming to enhance the gold and copper recovery of the plant. When native copper and GRGs are present in the deposit, this integration not only facilitates plant overall performance via removal of the valuables early in the circuit, but it also reduces downstream operational expenditures due to less retention time of coarser copper particles in the system.

Jan 1, 2019

By B. Kenney

For SOFCs, composite cathodes comprising an electronically conducting electro¬catalyst (e.g. LSM) and an conically conducting electrolyte material (e.g. YSZ) are considered to improve the electrochemical performance by extending the active reaction zone to regions beyond the electrolyte-electrode interface, as in the case of conventional cathodes. Interpretation of experimental data for composite cathodes, however, is complicated by the mixed conducting behaviour which results in local overpotential distributions throughout the composite cathode. These local overpotentials depend on many factors, such as the composition, particle size, porosity and thickness of the cathode. Reliable experimental data obtained from composite cathodes requires carefully crafted microstructural parameters in order to minimize the overpotential variations. A mathematical model of a composite cathode was developed using coupled differential equations describing transport and consumption of chemical species, oxygen ion and electrons. Simulations under various oxygen concentrations were used to obtain the reaction order of the oxygen reduction reaction. An apparent po2 dependency was then extracted from the predicted Rp vs P02 data. It was found that this p02 dependency can be significantly influenced by the micro-structural parameters of a composite cathode, primarily due to local overpotential distributions.

Jan 1, 2005

By R. W. Lawrence

"The management of acid rock drainage( ARD) to prevent impact when tailings are disposed of in the environment requires understanding of the phenomena giving rise to acidic drainage, a rigorous evaluation of the weathering characteristics of the tailings, and the successful implementation of control measures that will be effective in the long term. This paper provides a brief theoretical background to the complex reactions taking place in mill tailings containing residual sulfide minerals which must be appreciated to enable waste characterization program to be effective in predicting the future behavior of the tailings and in designing control methods which will work. The principals and practice of prediction and control as part of an ARD management strategy will then be discussed.Paper Not Available at Time of Publication"

Jan 1, 1997

By Laura Prati

Gold-on-carbon catalysts resulted very active and selective in liquid phase oxidation [1, 2, 3] and during past studies we established that activity is ruled by two factors: particle dimension and gold exposure on the carbon surface [4]. These two parameters are also connected to the nature of activated carbon where the chemical nature of the surface oxygenated groups probably plays an important role [5]. Our studies, focused on the design of an active gold-on-carbon catalyst for liquid phase application, were aimed, operating a fine tuning of all the parameters involved in determining activity, to optimize gold-on-carbon preparation, keeping in mind that gold particle activity increases with decreasing particle size and increasing gold exposure. Gold sol immobilisation represents a versatile methodology in preparing gold catalysts [6]: throughout this work we used as sol stabilizing agent, the N-dodecil-N,N-dimethyl-3-amino-1-propan sulphonate (SB), that provides both sterical and electrostatic stabilisation, a condition we already demonstrated necessary to preserve particle dimension when carbon is used as the support [6]. We generated different gold sols by varying the relative amount of reagents (HAuCl4, SB, NaBH4), the type of alkali and the temperature of the gold precursor reduction. Moreover, as we had recently evidenced that there is also a carbon effect [5], we employed only one active carbon to immobilize the sols.

Oct 1, 2003

By G. R. Yourt

"Generally speaking the usual approach for controlling dust is three-fold:1. Suppress the formation of dust at the source.2. Confine dust that cannot be suppressed.3. Dilute and remove dust that cannot be confined.This discussion will be concentrated on the second approach, namely, confining and disposing of dusty air.Dust BehaviourBefore delving into actual design principles a brief discussion on behaviour of dust should be helpful. For prevention of silicosis only respirable dust, ranging in size from < 0.5 to 5u needs to be controlled. As particles of this size have insignificant mass and momentum they follow air movements very closely. Consequently if contaminated air around dust sources is confined within enclosures and leakages maintained, strongly indraft dust is automatically controlled and capture velocities are of no concern.Dust SourcesAt metal mining operations ore is prepared for wet concentration by crushing it to mostly <3"" in size. This usually involves a jaw crusher, one or two cone crushers, one or more screens and several conveyors. Dust is actually produced only by the crushing action but it is liberated also when numerous fine particles contained in the ore stream are dispersed by surges and vibration at the discharge of the crushers, screens and headpulleys of conveyors. Furthermore, dust is dis¬persed when the slime adhering to the underside of the return portion of belts becomes dry and is rendered airborne by vibration and by cleaning floors especially where the slime has dropped."

Jan 1, 1971

By James F. Allan

"The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec. Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by =.0.10% Y2O3, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% ZrO2, The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and calc-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and minor britholite. Yttrium also occurs in britholite in calc-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By James F. Allan

"The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec. Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by =.0.10% Y2O3, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% ZrO2, The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and calc-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and minor britholite. Yttrium also occurs in britholite in calc-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By T Salman

The construction and use of the B.E.T. (gas adsorption) apparatus is described. Examples are given for the determination of large and small surface areas using nitrogen and krypton. Introduction A NY study of the milling of ores from crushing to grinding, classification, and concentration and finally dewatering of the products involves solid particles which are either in contact with a gas or a liquid phase. The surface area of the solid and its characteristics constitute important parameters in all mineral dressing operations. The success of any particular operation is dependent on the interaction of the surface of the solid particles with the gas or the liquid phase. Particle size and specific surface (surface area per unit weight) continue to be important parameters in the flotation research associated with the adsorption of collector molecules or ions on mineral particles, as in the early years of mineral dressing research (1). In order to understand the mechanism of the flotation process, it is essential that the surface properties of the adsorbent be known.

Jan 1, 1965

By Michael Bowker

Au/TiO2 catalysts were prepared by incipient wetness impregnation and tested for the room temperature photocatalytic reforming of methanol in aqueous solution. These catalysts proved to be more active, on a molar basis, than Pd/TiO2. The dependence on loading of gold was different from that of palladium, showing a double maximum in yield at 0.1 and 2 wt. % with low rate below 0.01% and above 10%. A model is proposed for the reaction involving band gap excitation of titania electrons which are used to oxidise the methanol via adsorbed CO. With palladium, photoreforming of CO and water can be achieved, but this is much less effective on gold, presumably due to the much weaker bonding of CO on Au.

Oct 1, 2003

By R. H. McMillan

A classification of important uranium deposits which utilizes both genetic and descriptive criteria is presented. The dual aspect is useful because, while the non-genetic nomenclature for the different deposit types is amenable to various interpretations, the critical characteristics of each deposit type can be analyzed to clarify various genetic points. Although the classification is intended primarily for Canadian uranium deposits, most of the important deposit types known elsewhere can be accommodated.

Jan 1, 1978

By DAVID C. MILLER

Barite deposits occur worldwide and in a variety of geological environments. In recent years, several deposits of barite and barite-lead-zinc have been discovered in northern British Columbia, Yukon Territory and Alaska. Most are associated with Devonian-Mississippian age sediments, and many are syngenetic, bedded-type deposits. The Mel is a barite-lead-zinc deposit; it lies within Lower Cambrian strata and appears to be of epigenetic replacement origin. Figure I is an aerial view of the property from the south. Observations herein described are based largely upon field work, megascopic studies and two recent B.A.Sc. theses (Biasucci 1979, Rennie 1979).

Jan 1, 1984

By T. Lux, H. -J. Krassnig, I. Filzwieser, E. Hecker, R. Degel, A. Filzwieser

Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions for the primary copper production lines as well as for non-ferrous metals starting with the primary smelting of concentrate and ending with the electrolysis. PolyMet Solutions provides the process know-how whereas SMS group supplies the plants and equipment and Mettop the key components. SMS group and Mettop also cooperate in the field of tankhouse technology. Together with Montanwerke Brixlegg AG, Mettop has developed together with a parallel flow technology (METTOP-BRX Technology), allowing a current efficiency of above 98 % at a current density of 420 A/m², which is a milestone in copper electrolysis. For the secondary copper production route, SMS group and PolyMet Solutions developed an innovative refining furnace (PolyRefine) for the smelting and refining of copper scrap. The refined copper is directly charged to the Contirod line to produce copper rods and wires. The innovative cooling solutions of SMS and PolyMet Solutions come into play where furnaces have to stand the highest loads and stresses, for instance in areas of very high temperatures or temperature fluctuations, aggressive exhaust gases and slags, or at critical spots such as taphole areas. Custom-tailored cooling systems for furnace vessels make sure varying loads are compensated in a targeted and effective manner. The solutions include air cooling, spray cooling, cooling technologies with integrated copper elements such as CFM (Composite Furnace Modular) cooling systems, plate and finger coolers. The major innovation in the field of furnace cooling is the ILTEC (Ionic Liquid Cooling) Technology which paves the way for increased plant safety. This revolutionary, patented cooling technology is jointly marketed by Mettop and SMS group. It permits water-free cooling to be implemented and thus makes operation safe wherever it is applied. INTRODUCTION Non-ferrous metals or NF metals are changing the world. There is no modern industrial sector that can do without these valuable metals. Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. The importance of the non-ferrous metals market is reflected by two figures. In 2018, the production of non-ferrous metals was worth more than 237 billion Euros. This contrasts with 255 billion Euros of the value of iron and ferro- alloy production in the same year (International Organizing Comittee for the World Mining Congresses, 2018). Hence, the NF metal industry is almost as important as the iron and steel industry. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions and to enhance customer value. The prices of nearly all metals have come under pressure during the past few years. Therefore, competitive technologies are regarded a crucial factor to achieve success in this critical market situation respectively to stabilize the market position.

Jan 1, 2019

The system of keeping geological plans and sections for the Geco Mine at Manitouwadge, Ontario, is described. Special methods employed to save draughting time with-out sacrificing accuracy, such as the extensive use of black line prints, are discussed. The uses made of the plans and sections by the mine planning engineers in their designs of stopes, and by the blast-hole engineer in ~is preparation of blast-hole layouts, are noted. An unusual scheme for portraying the distribution of .copper, zinc and silver values within the ore zone is de-scribed. The method of estimating the grade of ore to be "blasted in each ring of blast holes is outlined, as is the method of estimating the annual ore reserves. The design of an effective but simple transparent geo-logical and mine development model, used as a display for -visitors, is discussed. A large-scale model used for the study of problems in geological structure is also de-scribed.

Jan 1, 1964

By M. Connell, S. Bedrossian

Alkali cracking followed by chloride-based leaching is one of the prominent methods for rare earth element processing. Regeneration of the leach lixiviant, namely hydrochloric acid, is a critical operation in the process. A number of different process routes are available for recovery of hydrochloric acid from chloride solutions. The objective of this paper is to discuss various recovery routes and analyze the impact of several input variables on the variable operating cost.

Jan 1, 2014

By Georges Houlachi, Akram Alfantazi, Maysam Mohammadi

Manganese ions in zinc electrowinning electrolytes form a protective MnO2 layer that ultimately decreases Pb contamination in the zinc product. In this study, the effect of dissolved Mn2+ on the electrochemical performance of Pb, Pb-Ca and composite Pb-MnO2 anodes was investigated. The properties of the MnO2 layer formed on these anodes were studied and compared. Potentiodynamic polarization and cyclic voltammetry experiments were performed in 180 g L-1 sulphuric acid to study the electrochemical reactions occurring on the anodes. The anodes were subjected to galvanostatic polarization at 50 mA cm-2. The morphology and uniformity of the MnO2 layer on the anodes were examined using scanning electron microscopy (SEM). Experimental results revealed that the MnO2 layer formed on the composite anode was more compact and uniform compared to that formed on the Pb and Pb-Ca anode. It was also observed that the cell mud formation rate, and consequently manganese ions consumption, depended on the anode type. Although initial formation of the MnO2 layer decreased the oxygen evolution overpotential, its growth might negatively affect electrocatalytic activity of the anodes.

Jan 1, 2014

By Dirk Claessens

The term ?cost? is too small when describing the destructive power of safety incidents for mining companies. Breaches in employee or environmental safety are felt way beyond the bottom-line: human life can be taken; ecosystems tarnished; the ire of peoples, media and government inflamed; significant halting of production; and high levels of legal and financial challenges. According to a recent survey of Mining executivesi, ?ensuring workforce safety? was the most important issues identified above any other, with a plurality of 31 percent, reigning above capital projects, product efficiency, and equipment reliability. We accept that safety is a most paramount issue, yet for many reasons we keep approaching the problem the same way we have in the past. We need to stop doing the same things decade over decade and try something new. New innovations are significantly changing the fundamentals of how mining companies explore, excavate, produce, refine and distribute their valuable commodities. Technologies such as visualization, analytics, location awareness, and gaming simulation are making these enterprises smarter. Now, attention turns to an area we?ve long held as integral to our business: safety. By using the same breakthrough technologies that are changing our business, we can now boldly imagine ? and credibly strive for ? a world of zero incidents.

Aug 1, 2013

By S. L. Chen

The Kumera Technology Center developed a unique type of steam dryer for drying copper concentrate in the mid 1990s. The dryer has been chosen in several copper smelter projects since 1999. To expand production capacities, the Norddeutsche Affinerie smelter, the Pirdop smelter of Cumerio, the Toyo smelter of Sumitomo Metal Mining and the Tamano smelter of Hibi Kyodo Smelting have carried out projects in which Kumera Steam Dryers were installed. The capacity of a single steam dryer varies from 70 t/h to 160 t/h. This article summarizes the latest operation results of the Kumera Steam Dryers in these smelters and introduces the progress of the ongoing projects in Yanggu Xiangguang Copper, Guixi smelter of Jiangxi Copper, Jinlong Copper, Boliden Harjavalta, and Onsan smelter of LS-Nikko Copper.

Jan 1, 2007

By G. Chung, W. Petruk, D. Doyle

"A series of tests was conducted on Carol Lake iron ore, which contains about 38 wt % hematite and 19 wt % magnetite, to establish a flowsheet for high weight yield by spirals. A pilot plant was run in parallel with the IOC concentrator to simultaneously test two flowsheets on the same feed material. The IOC concentrator processes the ore by treating it directly in a spiral circuit, whereas the pilot plant used a laconite flowsheet which had a low intensity magnetic separator (LIMS) at the front of the circuit. The LIMS produced a non-magnetic (hematite-rich) product and a magnetic (magnetite-rich) product prior to treating the ore in two separate spiral circuits. The results from about 150 tests were evaluated by chemical assays and materials balancing techniques, and a selected test was evaluated by the image analysis and materials balancing technique.The image analysis and materials balancing evaluation showed that a higher hematite recovery was obtained by the hematite spiral circuit than by the IOC concentrator spiral circuit, and a slightly lower magnetite recovery by the magnetite spiral circuit than by the IOC concentrator spiral circuit. Furthermore the hematite recovery by hematite spirals was higher than the magnetite recovery by magnetite spirals. The better hematite recovery was achieved because a higher liberation is obtained for hematite than for magnetite, and the hematite in the Carol Lake ore has a narrower grain size range than magnetite. Consequently, better spiral control can be maintained when processing a hematite-rich spiral feed, than when processing a magnetite-rich spiral feed. Since the feed to the IOC concentrator spiral is a mixture of hematite and magnetite, an intermediate hematite recovery is obtained by the IOC concentrator. INTRODUCTIONA study of characteristics that affect recoveries of hematite and magnetite from the Carol Lake ores of the Iron Ore Company of Canada (IOC), was carried out in connection with a project on designing a flowsheet for maximum weight yields. A pilot plant using a taconite flowsheet was run in parallel with the existing IOC concentrator which uses a classical iron ore flowsheet. About 150 tests were run to compare iron recoveries and weight yields by the spirals in the two flowsheets. Better iron recoveries were indicated for the taconite flowsheet, but the results were not consistent and the reasons for the observed differences were not apparent. The material from one test (Test 61), which gave better iron recoveries for the taconite flowsheet, was evaluated by the image analysis and materials balancing technique. A suite of samples was taken from 5 points in the IOC concentrator and from 8 points in a pilot plant (taconite flowsheet). The samples were analyzed to compare the behaviours of the Carol Lake hematite and magnetite in the spirals of the two flowsheets. The results provided a sound basis for further tests in designing a high weight yield flow sheet."

Jan 1, 1993

By N. Djilali

Many of the transport phenomena encountered in proton exchange membrane fuel cells occur intrinsically at the microscale level. Physically representative models that fully account for the salient physico-chemical and transport processes in PEM fuel cells are necessary to achieve truly predictive models that can be used with confidence to: (i) gain a better understanding of in-situ processes and couplings, (ii) explore new concepts, and (iii) support design and optimization. The development of more general, rationally based macroscale models requires use of knowledge on the microscale level to provide guidance, and to determine the required parameters and coefficients (model "constants"). In this paper we present a new membrane transport model, the binary friction membrane model (BFM2), recently developed to account for coupled protonic and water transport in polymer membranes. This general model is based on rational and physical consideration, removes several of the limitations of the empirical models used to date, and is formulated for all purfluoro-sulfonic acid membranes. The use of the BFM2 in a fuel cell model is illustrated highlighting significant performance predictions compared to existing empirical model. The second part of the paper addresses the fundamentals of two-phase transport in hydrophobic gad diffusion media. Computational and experimental visualizations resolving the microscale dynamics of water transport between the fibres of a GDL are presented, revealing transport mechanisms that are, contrary to assumptions used to date, dominated by fingering and channeling.

Jan 1, 2005