Search Documents

By A. Taylor, M. Blanchette, J. Doucet

"A Z1600 Jameson Cell Test Rig was rented for test work at Vale’s Clarabelle Mill operation. This paper discusses the evolution of renting the unit for test purposes to owning the unit and operating it as a revenue generating process component. The paper focuses on three aspects of the Z1600 project; the initial rental and installation, the test work performed in the cleaning circuit, and the business factors which led to the unit being permanently incorporated into the copper circuit.INTRODUCTION Clarabelle Mill is located in Sudbury Ontario (approximately 350 km north of Toronto) on the southwest rim of the Sudbury basin a meteoric impact crater that is 62 km long and 30 km wide. The result of the meteoric impact was concentrated nickel (Ni), copper (Cu) and platinum group metal (PGM) ore bodies in the outer perimeter of the basin; described in more detail by Hanley (1957). Vale currently has seven operating mines in the Sudbury basin, from which nine distinct ore types are mined. Ores are also received from two QuadraFNX mines. Clarabelle Mill processes all of these ores for the Ontario Operations of Vale. The mill, commissioned in 1971, was originally built as one of four mills operated by then Inco Limited. Between the late 70’s and the early 90’s process changes were made to consolidate the Sudbury Operations milling processes into a single operating mill, Clarabelle Mill. In 1990, the SAG mill was installed resulting in peak mill throughput of 11.9 million short tons per annum (Mstpa), with typical throughputs of ~10 Mstpa. Mill average feed grades were 1.4% Cu and 1.2% Ni. During the resources boom, plans were developed to increase the mill capacity at Clarabelle Mill in stages to a final capacity of 13.5 Mstpa. The project known as the Clarabelle Mill Expansion and Recovery Project (CMERP) included expansion and reconfiguration of the grinding and flotation circuits. The first stage was a planned increase in grinding capacity with the reallocation of existing mills, the existing flotation capacity would be required to treat higher throughput until the new flotation circuit was constructed."

Jan 1, 2012

By Denilson Coutinho, Euler Soares, Paulo de Tarso, Jordana Ferreira, John R. Goode, Andreas Sprecher, Alexandre Rocha

The Serra Verde Project is located in the northern part of Goiás state, Brazil, and comprises 49 mineral claims covering an area of 69,814 ha. The Serra Verde deposit is a rare earth element (REE) enriched weathered granite comparable to the weathered granite, or ionic-clay, deposits found in southeastern China. The Mineral Reserves of the Serra Verde Project total 388 Mt (Measured and Indicated) at an average grade of 1,484 ppm of REE oxide (REO). Several hundred agitated leach and column leach tests have confirmed recovery of about 40 to 55% of the REE, except for Ce, using simple desorption techniques. Present plans call for a heap leach operation followed by precipitation of impurities and precipitation of a pure REE carbonate suitable for refining and separation. The project plan includes initial production of 5,000 t/a of REO, with a high content of heavy and critical REO, rising to 10,000 t/a of REO. This production rate will be obtained by mining of the Mineral Reserves over a 22-year mine life at an initial rate of 6 Mt/a for the first four years with the mining rate thereafter increasing as required by grade and production targets.

Jan 1, 2014

By E. J. Sun

The ADS system was developed to reduce accidents related to haul trucks operating under low visibility conditions in surface mining and construction sites, which is based on the GPS, mesh-wireless networks, and the Google-Earth 3D graphic engine as the graphic interface and mine-mapping server. This system has the capability to pin-point and track vehicles in real time using a 3D interface, which is based on user-based AutoCAD mine maps using the Google-Earth graphics interface. All equipped vehicles are shown in a 3D mine map stored in a local server through a wireless network. When low visibility conditions are present, the system indicates available exit/escape routes for driver safety. The research results indicate that the ADS system potentially increases reliability and reduces uncertainty in open pit mining operations by customizing the local 3D digital mining map, constructing the truck 3D models, tracking vehicles in real time using a 3D interface and indicating available escape routes for driver safety.

Oct 1, 2009

By Anna Maria Venezia

Bimetallic Au-Pd catalysts supported on amorphous silica-alumina (ASA) with vary amount of alumina (0, 8, 14, 28 and 100%) were prepared by the simultaneous reduction of palladium and gold precursors by ethanol in the presence of the polyvinylpyrrolidone (PVP). X-ray diffraction and X-ray photoelectron spectroscopy analyses indicated formation of alloyed Au-Pd particles. Ammonia temperature programmed desorption measurements were performed to monitor the acid strength and the amount of acid sites on the catalysts after their reduction with 10%H2/Ar at 573 K for 1h. The effect of the support acidity on the catalytic activity was investigated in the simultaneous hydrogenation (HYD) of toluene (T) and naphthalene (NP) in the presence of dibenzothiophene (DBT). Coke formation was also determined. Under the selected conditions (P = 5.0 MPa, T = 523 K, WHSV = 41.2 h-1), all the catalysts were resistant to poisoning with 113 ppm of S (as DBT). The hydrogenation activity of toluene and the HDS activity of DBT were found to correlate with the concentration of the medium strength acid sites. The enhancement of the HYD activity and the S- tolerance was related to modifications of the electronic properties of the metal atom upon interaction with the Brönsted acid sites and upon intermetallic interaction.

Oct 1, 2003

By K. Harris, J. B. Wahl

Ni-base superalloy cast materials provide an outstanding balance of high temperature strength, fatigue resistance, oxidation resistance and coating performance and can be produced to very tight tolerances in extremely complex configurations, such as axial and centrifugal integral cast turbine wheels. As a result, cast superalloys are used in the most demanding applications of aero and industrial gas turbine engines. Use of these materials is expanding to smaller microturbine, turbojet, turbocharger and missile engine applications due to this unique combination of desirable properties. This paper will present an overview of the application of investment cast Ni-base superalloys and process capability to small turbine and missile engines.

Jan 1, 2010

By Stephen J. Roberts

Gold catalysts were prepared on co-precipitated, calcined copper oxide - zinc oxide support by an inverse deposition-precipitation method. These catalysts were characterised by X-ray diffraction (XRD) and temperature-programmed reduction (TPR) and studied for CO oxidation activity at various catalyst calcination temperatures. TPR studies of the support material exhibited a double peak and shift to lower temperatures for the reduction of Cux+ to metallic copper, as opposed to the single reduction peak for pure CuO. This phenomenon is possibly caused by an interaction with the zinc oxide. The addition of gold to the support CuOZnO led to a further shift in copper reducibility to lower temperatures. Gold present in the initial uncalcined catalyst as Au3+ was auto-reduced to Au0 under various calcination temperatures. The Au3+ reduction peak was observed to shift to lower temperatures with increasing calcination temperature. The catalytic activity was found to pass through a minimum value with respect to calcination temperature. Catalysts with both gold in entirely the 3+ or metallic oxidation state were found to exhibit high activity. Furthermore, the catalysts were found to decrease in activity with decreasing Au3+ content up to an intermediate calcination temperature, afterwhich the activity increased sharply. Possibly at higher temperatures, a stronger Au-support interaction is formed, leading to a new active site.

Oct 1, 2003

By P. S. Capper

"Generally speaking, the most intensive efforts at dust control in the mining industry have, in the past, been concerned with underground operations and where uranium ore or high silica material is processed. In the past several years, Stoop Rock has made Intensive efforts to reduce dust levels in it's Iron ore pelletizing complex. There have been no great engineering break-throughs with regard to dust control in such plants, and certainly no new engineering techniques have had to be applied at Steep Rock. This paper deals with how significant improvements in dust levels have been achieved through minor modification to dust collectors and ventilation units, improvements in operating practices, and education of supervisors and hourly personnel.PROCESS DESCRIPTIONSteep Rock Iron Mines is located 120 miles west of Thunder Bay near Atikokan. (fig. 1) Run-of-mine ore is pelletized along with some -1"" concentrate that has been processed in the concentrator (a summer operation only), which utilizes gravity separation to upgrade a mechanical mixture of ore and waste."

Jan 1, 1976

By B. K. Gorain

"Mining of low grade deposits along with the necessity to design and operate process plants requiring high throughputs presents unique metallurgical environmental and sustainability challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life-of-mine.Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy and high ore variability, water scarcity and quality issues, high energy costs, complex environmental issues including tailings management, high capital and operating costs, worldwide constraints on resource availability, complicated regulations in emerging economies, changing demographics of mining operations with ever-changing cultural or community issues and the urgent need for a better assessment of project viability to reflect the dynamics of present mining scenario. Developing breakthrough solutions to these problems is the key to success of any new project and maintaining profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial along with the need for a more lateral thinking, strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex metallurgical problems.IntroductionThere is a plethora of challenges in developing new ore bodies. The metallurgical complexity of these deposits has increased significantly due to the need for mining lower grade ores along with the presence of deleterious elements that have environmental and processing implications. In addition, many of the mining projects are capital intensive due to high throughput requirements to be economical along with the need for building infrastructure due to remote locations, while operating costs steadily increase due to high reagent, energy and labour costs, increased state royalties and community obligations, to name a few of the key factors. There is also scarcity of water in many regions requiring the use of sea water or brackish water, which has both environmental and metallurgical implications. The shortage of qualified technical manpower adds significantly to the woes of many mining companies. Considering these multiplicity of challenges, it has become imperative for many mining companies to be innovative in addressing these issues."

Jan 1, 2015

By Ken Witherly

Modern airborne EM surveys typically acquire more data than is processed or analyzed at the time of acquisition Suitable additional processing can provide more diagnostic information, thereby allowing for more effective ranking and hopefully, follow-up of outcomes

Apr 1, 2005

By Y. S. Sun, Northeastern University, W. B. Li, P. Gao, Z. Y. Zhang, J. W. Yu

"The boron-bearing iron concentrate was extracted from ludwigite ore by the process of magnetic-gravity separation. In order to fully utilize the refractory ore and meet the boron consumption of China, a novel process for separation of boron from iron in boron-bearing iron concentrate was proposed in this paper. In particular, laboratory scale experiments of improving boron reactivity were performed. Fine boron-bearing iron concentrate briquettes were reduced by bituminous coal completely at 1125 °C for 150 min. The effect of sodium carbonate, which was used as an additive in the roasting process, was investigated. The addition of sodium carbonate decreased the boron reactivity and facilitated the volatilization of boron. The influence of diverse cooling methods of the reduced samples on the boron reactivity was studied. The results indicated that boron reactivity could reach up to 80.76% when the reduced samples were cooled by rapid water quenching. In addition, the magnetic material containing 92.71 % Fe with a recovery of 95.11 % and boron-rich non-magnetic material containing 14.51% B2O3 with a recovery 88.85% could be obtained by low-intensity magnetic separation. The magnetic material and boron-rich non-magnetic material were good raw materials for steel-making and borax production, respectively.INTRODUCTION Ludwigite ore is abundant in Liaoning province of China, with 28.43 Mt B2O3 accounting for 57% of the boron resources of the country (Liu et al., 2006). However, it has not yet been utilized on an industrial scale due to its complex mineralogy and fine mineral dissemination (Wang, Wang, Ding, Ma & Xue, 2012). At present, boron-bearing iron concentrate and boron concentrate can be obtained from ludwigite ore using magnetic-gravity separation. The boron concentrate contains B2O3 12%~16%, which can be used as a high-quality raw material for the boron chemical industry after activated roasting, but the B2O3 content in the iron concentrate reaches up to 4%~6%. In order to further separate boron and iron from boron-bearing iron concentrate, a blast furnace and a solid pre-reduction followed by electric arc furnace melting have been proposed (Liu, Cui & Zhang, 1998; Wang et al., 2012). However, both of these two current routes face the same crucial problem that molten boron-rich slag has to be cooled slowly to obtain the alkali-dissolution activity of boron, which affects the yield of boron resource."

Jan 1, 2016

By A. L. Rutledge, R. S. Nichols

"Waste dump development at the Fording River Operation s in British Columbia began in 1971. In 1981, several unique as well as unplanned situations provided an opportunity to study water flows through waste dumps.The key to the drainage is naturally segregated rock sizes .created by end dumping from the crest of a pile. The largest size material accumulates at the toe. Flow rates along the base of the studied dumps varied from 2,800 to 13,500 m3/day or 0.032 to 0. 156 m3/s (1.2-5.5 cfs}. Sediment concentrations in the water ranged from 1 to 1,800 mg/I.This paper describes water flows through dumps of varied lithology and maturity. The results suggest that neither long-term water flow nor contained sediments in small streams are jeopardized when crossed by end-dumped fills.IntroductionThe Fording River Operations are located in southeastern British Columbia approximately 115 km north of the United State s and 10 km west of Alberta, within the medial range of the Rocky Mountains. All production is carried out at elevations ranging between 1,600 and 2,200 m above sea level.The property is within a continental climatic zone, with temperature extremes of - 40°C in January to +35°C in July. The average annual precipitation of 335 mm of rainfall and 390 cm of snowfall feeds the numerous seasonal, small drainage courses along the Fording River valley.Since start-up in 1971, 149 million bank cubic met res of waste from truck-shovel and dragline mining have been placed in numerous dumps or ""spoils"". The dumps were developed to the point that several unique situations could be studied. During the peak run-off period of May-June 1981, water flow studies were performed on dumps of varied lithology and maturity. This paper describes the results of the study."

Jan 1, 1982

By X. Grant Chen, A. R. Farkoosh, M. Pekguleryuz

Nano-scale Al-(Fe,Mo)-Si dispersoids form during solution treatment in grain interiors (intradendritic regions) of cast Al7Si0.5Cu0.3Mg alloyed with 0.3Mo (wt.%). Unlike the Q-Al5Cu2Mg8Si6 and ?-Al2Cu age-hardening precipitates which coarsen resulting in loss of strength in Al-Si-Cu-Mg alloys, these Mo-containing dispersoids are thermally stable and retain their strengthening effect at elevated temperatures. Consequently, the age-hardened Al7Si0.5Cu0.3Mg0.3Mo (wt.%) exhibits high strength and creep resistance at 300 °C.

Jan 1, 2014

By J. R. Hart, V. C. Smith, V. P. Babarovich-Hansen, J. H. Schubert

"An introduction and case study of Mintek's latest generation of Milling Circuit controller, the MillStarTM with IES (Interpreting Expert System) is presented. This paper also describes as a case study its installation on a Southern African base metals concentrator plant which has demonstrated improved operation, greatly reduced variation in product quality, as well as increased capacity and availability of the circuit.In this case study, the MillStarTMw as installed along with several other enhancements, including hydrocyclone underflow monitoring, product particle size estimation and flotation circuit stabilisation. MillStarTM utilised the particle size measurement to control grind to within 2% of setpoint, all the while ensuring sump level control, density control as well as mill power optimisation. Mintek' s expertise in the modelling of tumbling mills allowed the development of a specialised optimising controller that ensured the mill was kept in the most efficient operating region.MillStarTM augments the automatic control with useful user interface features, such as on-line trends of any logged variables, historic data warehousing and retrieval and production summary reports.A novel feature that distinguishes the MillStarTMi s the IES (Interpreting Expert System). This is a feature of the software that works with the automatic control code to generate explanations for control actions made by the controller. Often complex control systems are mysterious in nature, reducing trust and eventually resulting in them being switched off. The IES method of exposing the heart of the controller has proved popular and is seen to have potential as a training tool. 314"

Jan 1, 2000

By D. Verhulst

The Altair process digests ilmenite concentrate in high-chloride HC1 solution, with complete dissolution of titanium and iron. The Fe(III) ions are reduced to the ferrous form, and the solution is cooled to produce crystalline ferrous chloride. Titanium is transferred by solvent extraction into a purified, concentrated Ti stream, which is spray-hydrolyzed to produce TiO2 hydrate. The hydrate is further calcined with additives to generate a high-quality pigment. All the chloride streams are recycled. In the original flowsheet, the iron chloride is pyrohydrolyzed by spray roasting to regenerate 18% HCl, which is subsequently converted to HC1 gas and water by pressure-swing distillation. A modified flowsheet includes an alternative to iron chloride spray roasting, producing more concentrated HCl and decreasing the amount of solution to be distilled. Improvements in digestion, solvent extraction and final pigment production are also introduced. A 100 t/y pilot plant is being built and will test the new concepts and confirm the overall water, acid and impurity balances of the process.

Jan 1, 2006

By M. Labrie, H. L. Gibson, G. Doiron, J. J. Watkins, D. H. Watkinson

The Corbet deposit is one of 17 proximal Cu-Zn massive sulfide deposits located. within the Noranda Cauldron which occurs within the core of the Noranda Volcanic Complex. The deposit is located at the top of the Havrian Formation, the lowermost formation of the 3000 m thick Mine Sequence; the deposit has Yielded 2.75 M tonnes of ore grading 3% Cu, 0.96% Zn, 2.06 g/t Ag and 1.0 g/t Au. The multi-lens Corbet deposit formed within a 250 m wide crater that occurs within a localized breccia pile. The Corbet breccia pile was constructed by explosive magmatic and hydrovolcanic eruptions localized along the south flank of a larger andesitic shield volcano that formed during the waning stages of Havrian volcanism. The breccia footwall of the deposit allowed unfocused and widespread hydrothermal discharge that resulted in the development of a large area of chlorite and fringing sericite alteration that exceeds, by six times, the size of the sulfide lenses and represents a significant exploration target.

Jan 1, 1993

By Shamia Hoque, Charles Q. Jia

Smelter slags contain valuable metals such as Co, Ni and Cu in proportions of less than 1 wt% along with about 40 wt% of Fe and 15 wt% of Si. Although aqueous SO2 is a versatile lixiviant for transition metals, dissolving the slag in aqueous SO2 produces solutions in which Co and Ni concentrations are lower than that of Fe due to the low metal/ Fe ratio in the slag. To develop the options for increasing Co and Ni concentrations the solubility of slag in aqueous SO2 was studied experimentally and theoretically using OLI, a software package for simulating electrolytes chemistry. The modeling results correlated well with experimental results. The model suggested that the species dominating the system was FeSO3, which would precipitate out as FeSO3.3H2O when the concentration of Fe+2 reached 1.22 molal and the concentration of S032- was beyond 1.4 molal. In the experiments the influence of pH and solids loading were studied. The leach solution obtained after dissolution of slag at 50% solids loading had a pH of 1.85. On raising the pH to 3, precipitation occurred. Analysis of the solution collected after the addition of alkali showed over 50% reduction of Fe, Co and Ni. XRD analysis revealed the precipitate to be of amorphous nature due to the silica present. The analysis confirmed that the precipitate was mainly FeSO3.3H2O. The paper also discusses the potential impact of the slag on the environment.

Jan 1, 2004

By A. R. Laplante

"In this paper, the performance of the Knelson Concentrator and of the batch and continuous Falcon Concentrators are compared. The units are based on different operating principles, and as such they perform quite differently. The Knelson yields very high free gold recoveries over a wide size range of both the recovered and rejected species. It is ineffective in recovering very fine ( <15 µm) or flaky gold, as encountered in flotation feeds, concentrates or tails. It is the: preferred unit for gold recovery from grinding circuits. The batch Falcon is effective in the fine range, typically less than 37 µm for gold. Its recovery zone is quickly saturated when there is significant heavies in the feed. It works best as a pre-concentration unit. The continuous Falcon is a versatile unit which is capable of recovering fine heavies (density down to 5 g/cm3 ), especially from coarser gangue. INTRODUCTIONThe purpose of this presentation is to describe the mode of operation of two Canadian centrifugal concentrators, the Knelson and Falcon. It is hoped that it will prove informative to prospective users in the selection, testing and optimization for applications of either machine. The work is based on testwork both in Canadian mills and at McGill. I am indebted to many colleagues at these locations. Appropriate references will be made to articles further describing the work, either already in the open literature or in preparation.Although this work is meant to be more practical than scholarly, it is appropriate to begin by considering how the two units achieve selective recovery. This will become useful in establishing a suitable testing methodology, which will then be described, and interpreting typical results. In the last section I will attempt to define appropriate applications for the two units. This is a thankless task, as I am likely to miss some applications or to make projections based on partial results, as much of the work is still in progress. In deference to the reader and both manufacturers, areas where reasonable doubt still remains will be identified."

Jan 1, 1993

By Bern Klein, Malcolm Scoble, Justin Widdifield, Andrew Bamber

"It has been suggested that the pre-concentration of ore underground can bring positive economic and environmental benefits to underground mining, particularly at extreme depth. The integration of mineral processing systems for coarse waste rejection and disposal into the underground mining environment has a substantial impact on the economics and operation of the mine. A case study for the integration of underground pre-concentration at Falconbridge’s Thayer Lindsley and Fraser Copper operations in Sudbury, Ontario is discussed, with particular focus on ore evaluation, system design, integration, and impacts on the operation. Conclusions as to the overall feasibility and potential impacts of underground pre-concentration are presented.INTRODUCTIONObjectivesA scoping investigation has been conducted for Falconbridge Ltd on the Fraser Copper Zone and Thayer Lindsley mines in order to develop a better understanding of the operations, and to do a preliminary evaluation of the potential for pre-concentration of the ore underground. The objective was to develop a conceptual design and evaluation of a pre-concentration system for each site. The results are to be used as the basis for a more detailed future study.Underground Pre-ConcentrationThe pre-concentration of ore to reduce the quantity and improve the quality of material transported to the processing plant is not a new concept and has been in practise at several mines including the American Zinc Company in Mascot Tennessee (Munro et al, 1982), the Sullivan Mine in British Columbia and presently at Xstrata’s Mt Isa lead-zinc mine in Australia, as well as at several PGM mines operating in the South African Bushveld. For each of these mines, a high degree of waste rejection was achieved at a coarse particle size with good metallurgical recoveries. The benefits arising from the surface pre-concentration of ore are well documented in the literature (McCullough et al, 1999; Miller et al, 1978; Munro et al, 1982; Schena et al, 1990; Sivamohan & Forssberg, 1991)."

Jan 1, 2006

"The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copperzinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products.Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance.Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of run-of-mine and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling.One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost, and reagent consumption.Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ‘equivalent’) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties, and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ore becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance, and thereby profitability, is a powerful tool.In an operation such as Antamina, where managing ore sources, campaigns, and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency."

Jan 1, 2005

By Rodney G. Orr, Phil Robertshaw, Roland Loewer, Klau Lehnert-Thiel

This paper documents the 1988 discovery and subsequent evaluation (to 1991) of diamond bearing kimberlites in the Fort à la Corne area, Saskatchewan, by Uranerz Exploration and Mining Limited. Cameco Corporation began participating as a joint venture partner (50%) in mid-1989. The first indications that kimberlite-type intrusions might exist in the area carne from Geological Survey of Canada aeromagnetic maps. Because of the overburden thickness (over 100 m), magnetometer surveys continue to be the main exploration tool in defining pipe locations and sizes. Magnetometer surveys in varying levels of detail have outlined one main cluster and two sub-clusters, the main group being some 10 km by 50 km in size. In excess of 70 individual targets have been interpreted from the magnetics as probably representing kimberlites. The size range of the individual magnetically-defined bodies is between 1 ha and 74 ha. Proof that the magnetic anomalies were kimberlite intrusions carne in 1989 when each of seven test holes, all drilled on different targets, intersected the potential diamond host rock. The majority of the targets tested were diamond-bearing, with the indicator mineral chemistries suggesting that both peridotitic and ecIogitic diamond parageneses could be expected. To date, 18 individual kimberlite bodies have been drill-tested. A total of 39 bulk samples, amounting to 186 t (representing 360 t of theoretical sample recoveries) were processed in 1990 and 1991. One hundred and sixty diamonds were recovered, averaging 0.04 carats in weight, the largest being 0.6 carats. Most of the bulk sample grades are less than 2 carats/loo t; only three bulk samples have higher grades, the best being approximately 10.5 carats/l00 1. The diamonds are predominantly gem-quality stones.

Jan 1, 1992