Search Documents

MR JOHN S Foxall wrote: Mr Clayton in his paper on the above subject (Proceedings, N.S. No. 34) made an assertion which should not be allowed to remain unchallenged. On the top of page 10 appears the following statement;- "By viewing the box at adepression angle of 45°, all the dimensions are disclosed and the box may be projected on isometric co-ordinates" and lower down on the same page:- "An isometric plan, being virtually a projection on a plane inclined at 45°, the nearer the dip approaches this figure so is the outline of the stoping more truly shown." Those statements embody an inaccuracy which would be misleading were an isometric plan to be constructed to suit a special case, ie the case of a mine whose lode dipped at 45°, or approximately 45° and it would be found that in such a plan the outline of the stoping would not be truly shown. The reason for this is that the depression angle at which an object is viewed in order to...

Jan 1, 1920

By J Naser, M Tuck

This paper reports a computational study using computational fluid dynamics (CFD) in a mine ventilation system. Ambient air is injected to a rectangular mine drive through a circular duct. Moisture evaporates from shaft wall depending on flow properties of air in the drive-duct system. The physical process involves simultaneous momentum, heat and mass transfer. A species transport equation is employed to account for the moisture concentration in air. The momentum equation is solved using standard k- model, while energy and species transport equations are solved using standard expressions for moisture evaporation rate and heat flux from the drive wall. The aim of this paper is to investigate effectiveness of CFD simulation in relation to mine ventilation in a drive where a significant mass transfer phenomenon occurs. Results from simulation are compared with existing data from a site in Victoria.

Jan 1, 2005

Wollongong* is Australia's largest single centre of mining and metallurgy. Wollongong's total employment in manufacturing of basic metal products (over 26,500 in 1972/1973) was almost 50 per cent higher than that of Newcastle and double that of any other Australian city. Although the great bulk of this employment was in steelmaking, Wollongong's copper industry was also a significant employer. Wollongong's total employment in mining (4,900 in 1971) was second only to that of Newcastle among Australian mining centres. Although the bulk of Wollongong's mining is of coal, there is also considerable mining of blue metal, sand and clay. In all, over 40 per cent of Wollongong's work force is employed in mining and metallurgy. The great bulk of the other

Jan 1, 1976

By L Ryan, S Halley

The use of a field spectrometer to systematically analyse drill samples from over 200 holes around the Permian-Carboniferous Ravenswood gold deposits in north-east Queensland has successfully identified both small and deposit-scale changes in the alteration mineral chemistry. Changes in chlorite composition within the tonalite host rocks are evident at the district scale, with Fe-rich chlorites seemingly more common in the vicinity of the deposits. Significant variations in white mica chemistry also occur, but mostly on the vein selvage scale, with no clear distinction between near-mine and distal compositions. The results indicate that chlorite compositional maps produced from regional field or airborne spectrometer data could potentially be used as a vector to ore in exploring for similar deposits in the area. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Before exploration programmes or minerals developments are formulated, a mining company ought to assess how capital can be returned if the project is successful. A fact not well appreciated by the minerals community is that it is often difficult to get money out of many Pacific Rim countries due to special foreign exchange controls or restrictions on dividend or capital repatriation. On top of this risk are factors such as creeping expropriation through administrative, fiscal, or corruption pressures; environmental regulations; terrorists; and organised labour and political activists. Political risk is much more than just expropriation or nationalisation.Political risk factors can make or break a project in many PacRim countries and just the cost of delays and negotiations can insidiously affect project economics. This unpalatable thought, however, can be readily addressed by either legal structuring e.g. offshore proceeds accounts, offset/back-to-back currency hedges, or political risk insurance for the equity as well as any subsequent project development debt.

Jan 1, 1990

Since 1960, the Dongchuan Copper Mining Bureau, Yunnan Province, China, has treated copper oxidised ores by sulphidisation - flotation technique only to recover copper. In order to improve the metallurgical performances and economics of flotation, extensive development work has been carried out during the past 30 years: several specific flotation flowsheets have evolved from the originally selected `stage - grinding and stage - flotation' flowsheet to suit various ores; the overall grinding size of the ores has been increased from 80 per cent - 200 mesh to 90 per cent - 200 mesh, resulting in significant increase in copper recovery; the substitution of CaS for NazS proved to be successful in sulphidisation of copper oxidised minerals, and also in avoiding the depressing effect of Na2S on copper sulphide minerals; the application of a number of activators of copper oxidised minerals, especially ethylene diamine phosphate, has considerably improved the flotation performance and decreased the consumptions of other reagents. Finally, the combined use of sodium hydroximate with butyl xanthate has been shown to be effective in enhancing the floatability of both copper oxidised and sulphide minerals.

Jan 1, 1993

By M Darby, B Burdett, F Lovell

The results of the process control improvement project aimed at improving the quality of Australian Bulk MineralsÆ (ABM) iron ore pellets produced by four vertical shaft furnaces are very positive. These results are achieved through process stabilisation and optimisation, improvement in process monitoring and taking early corrective actions when operating variables were outside the target ranges. A number of benefits are obtained from this project. These benefits include: More consistent and improved pellet quality. The average cold compression strength (CCS) value of pellets produced during the eight-month trial is 260 kg/pellet, which is 16 kg/pellet higher than that produced during the 12 months prior to the trial (244 kg/pellet). Reduction in the heat input by eight per cent, from 727 MJ/tonne to 668 MJ/tonne. Reduction in bentonite rate by six per cent, from 7.1 kg/tonne to 6.7 kg/tonne. Increase in the furnace throughput rate by four per cent and additional production of 10 000 tonnes per annum through process stabilisation. Better understanding of the process behaviour. This knowledge is valuable not only for setting the target operating conditions but also for developing the ABM expert system to control the process.

Jan 1, 2005

Geotechnical practice combines the site engineering geological model with engineering design and operations to control risk. The responsibility of the geotechnical professional is to present relevant engineering geological information to an engineer to effectively impact an outcome. Return is enhanced by understanding expected operating and capital cost due to ground conditions.   Risk is effectively communicated by a successful geotechnical practitioner. In a mining environment the need is to assess ground conditions accurately and quickly, and to effectively communicate expected ground response due to mining. A good engineering geological model includes a description of geotechnical engineering parameters to design assuming reasonable expected soil, rock and water conditions. Pit slopes are steepened, stope spans widened and waste foundations and land forms are constructed all under geotechnical control.   The responsibility of the geotechnical professional is to collect, assess and disseminate relative engineering geological information. The geotechnical professional is a person advising on ground related engineering, and generally operates within geology and engineering end members.   Return is better assessed on an understanding of ground cost. In operations the goal is to meet production at lower cost. In evaluation, regional and exploration geology, mine design and expected operational factors influence expected cost and project return. Return allows companies to meet shareholder expectations, attract equity to develop and add value to the community.   This paper presents a discussion with some examples to present an approach and design philosophy for geotechnical practice in the mining industry.

Jan 1, 2004

Strong markets for metals and energy over the past five years have supported equity and debt market funding to enable a new group of mining juniors to emerge in control of economic resources, some in regions with high investment risk. As companies drive these projects to development, production and positive operating cash flow, their Boards and CEOs are confronting important questions:Having achieved initial success, what is our longer term purpose as a company? Does the purpose originally described in the Initial Public Offering to raise equity remain wholly relevant? Given that purpose, how do we understand the available sets of opportunities and related risks? Should we be acquiring new assets or other companies, or developing the existing portfolio? What commodity sectors and geographies should we focus on? Or should we be conserving funds until asset prices or project costs provide greater assurance of value to shareholders? How do we translate that purpose into tangible goals that shape and direct the work of people in the organisation? How do we get the right work done in the face of high turnover and competition for capable staff? Drawing on the authorÆs career experience and on work undertaken by Heuris Partners, this paper provides a practical CEO framework for strategy development, organisation design and on planning the work of the business in the mining industry.

Jan 1, 2006

Agitation leaching data has generally not been analysed to extract the maximum amount of information that is available. Analysis of heap leaching systems has been developing over the last five years to include the underlying rate determining process. This has been found to be diffusion control for all copper leaching; irrespective of whether they are oxide or sulfide minerals. Extension of the diffusion model has enabled better scale-up protocols to be developed. Acid consumption in copper heap leaching operations has been found to be a first-order chemical controlled system. The analysis of the data is relatively straightforward. However the interpretation and scale-up is not as direct as for agitation leaching. The differences in the residence time distributions (RTDs) are required to properly account for the scale-up between test columns and field. The leaching of oxide copper in agitated systems has also been found to be diffusion controlled. However, there are significant differences in the control mechanisms. Initially the leaching control is the supply of acid to the mineral surface. This is limited by the diffusion through the surface boundary layer and is thus subject to the level of agitation. Higher agitation provides thinner boundary layers and faster diffusion rates. Similarly, higher grade material creates a thicker concentration boundary layer and relatively slower leaching. Acid consumption in agitated leach systems is also a first-order system. However, the interpretation of the RTD is easier from batch testing to continuous multiple CSTR series plant operations. Altering the method of acid delivery can significantly reduce acid consumption rates. Predilution of the acid minimises the local acid concentration near the addition point and can reduce the consumption by up to 50 per cent. Modelling of the combined leach rate(s) and acid consumption rates in agitated systems allows comparison of various leaching strategies and selection of the most appropriate. Similarly, the model allows the identification of economic limits to leach recovery; where the cost of acid consumption is greater than the value of the copper recovered. From this analysis selection of residence times for agitation leaching can be determined. The modelling tools are useful in identifying optimum conditions for the leaching process.

Jan 1, 2005

By P Hanna

In an effort to improve returns to shareholders, the Australian Mining Industry has consolidated considerably over the past decade or so. Technical services at mines have been re-structured, whilst those at corporate offices have been all but eliminated. A recent study of the role of the geologist in BM Alliance Coal Operations Pty Ltd (BMA), showed the adverse impact on the companyÆs performance due to a lack of geologists. With an education campaign, to demonstrate the contribution of geologists to the æbottom lineÆ and in increasing the options available to the company, the value of the geology role became better understood. The implications of the loss of invaluable corporate knowledge, when long serving geologists left the company, also became clear. Steps have since been taken to increase the numbers of company geologists, particularly on mine sites. In common with other sectors of the mining industry, the Australian coal industry is experiencing a critical shortage of experienced coal geologists, as companies have found in recent recruitment efforts. This is further evidence that the recommendations from the recent study by World Competitive Practices, commissioned by The Australasian Institute of Mining and Metallurgy, æRising to the ChallengeÆ have not been adopted. People, and the mineral resource base, are the assets from which mining companies gain a sustainable competitive advantage. Geologists, as the nexus between the resource base and people, are in a unique position to enhance the profitability of their companies. To maximise their contribution to the industry, and ensure that they receive due recognition, geologists must adopt a more commercial approach in their work and take a front foot stance in promoting their value to management. Geology is a core competency for all mining companies. The tendency for companies to outsource this function, to the detriment of the company geologist role, is not sustainable in the longer term. TodayÆs geologists need to work closely with management, technical and human resource professionals, universities and schools to ensure their significant value is well understood, and that the industry can attract, train and retain new recruits through the implementation of graduate programs and company career paths.

Jan 1, 2003

The Australian Mining Industry Council is the peak mining industry representative body in the country. It is wholly funded by its member companies which comprise all of the major Australian mining houses. AMIC represents companies invo

Jan 1, 1994

By Denholm WT

The Dittmer process for the debismuthising of lead by electrolysis beneath molten caustic soda has been scaled up to 100 kg lots for batchwise operation and to 20 kg per hour for a continuous flow of lead. Bismuth was decreas- ed from 0.03 to less than 0.005 wt. per cent for an electricity consumption of 220 kWh per ton of lead. Lower bismuth levels may be readily achieved if required.

Jan 1, 1975

Continuing education is recognised as an essential aspect of professional training, but no systematic procedures have hitherto been attempted. The tertiary educational institut- ions are making a valuable contribution without formal financial support. The Australian Mineral Foundation is offering a programme of continuing education in the earth science and related disciplines both by direct initiative and by co-operation with existing tertiary educational institutions.

Jan 1, 1974

Inadequate understanding and/or assessment of technical and economic risk associated with geological uncertainty are key reasons many mining projects do not achieve forecast profitability. In the last 20 years many new and existing mines have experienced geology related problems, including lower than planned development and production rates, geotechnical/stability issues, unplanned dilution, ore loss, reduced metallurgical performance, environmental management concerns and unbudgeted capital/operating costs. Greater emphasis on the evaluation and communication of uncertainty associated with geological interpretations for feasibility and operations management results in better decision-making. The outcome of better decision-making is more efficient mining yielding enhanced financial returns for the mining industry.

Jan 1, 2009

By Jin C, Shuyi L, Yuanbiao Z

This paper describes the structure, performance, principle and effectiveness of a new laboratory type of composed-forces field separator utilising the composition of the magnetic force, vibrating force, pulsating force, gravity and fluid-viscous force etc to separate fine feebly magnetic valuable minerals. Compared with the pulsating high gradient magnetic separator, this separator possesses unique advantages of higher enrichment ratio and higher recovery of the magnetic component.

Jan 1, 1993

A review of the motivation of personnel in the open cut mining industry. The effect of social, geographic, environ- mental, organisational, union and other factors on employees' motivation as assessed from job experience and from an attitude survey. An appraisal of where we should be heading and what influence management can have on the motivation of employees.

Jan 1, 1980

By Diehl GW, Kuntonen J

The Tamrock all-hydraulic rock drilling system 400 has been developed to cover as wide a drilling range as possible, from 35 mm holes in tunnelling, roofbolting and development work to 64mm holes in long hole production drilling. Field experience during the last five years shows that the Tamrock drill covers this range in a way that no other rock drill on the market does and recently the range has been success- fully further expanded to cover bench drilling with 76 mm holes.

Jan 1, 1978

Pressures are foreseen for departments of metallurgy to make. radical changes in their undergraduate curricula. The curricula need to be made more attractive to high'school students in -order to increase the number of enrolled students. The distinctive character of extractive metallurgy needs to be emphasised to resist encroachment by chemical engineering. There should be content relevant to each of the professional functions and, particularly, to' society's broad expectations of metallurgists. Content, teaching methods, etc. need to be acceptable to women, mature-age -students, Aboriginals, and other groups, as well as young white males. Learning experiences should be negotiable by the students in response to the advent of learning packages delivered via personal computers. All of these needs could be satisfied by a radical change. in attitudes and objectives during the design; implementation and evaluation stages of . a new type of curriculum, using a wide range of problem-based learning experiences..

Jan 1, 1986

Future metal prices play a direct role in both the economic evaluation and short to medium planning of a mine scheduling sequence. It is difficult to predict with accuracy the future price of volatile metal commodities, however, it is possible to fix some future metal price, outside of long term contracts by the selling of futures contracts through a commodities exchange. The futures contract represents a fixed amount of a speci- fied quality of a commodity for future delivery at a predetermined price. Several different types of hedginc are possible, one in particular which is best suited for mining companies. There are relative advantages and disadvantages when trading in futures contracts and particular reference is made to gold contracts on the Sydney Futures Exchange.

Jan 1, 1980