Search Documents

By Campain RA, Horner NJ, Limerick JM

The review covers the different concepts of automation which are appropriate to non-ferrous smelting and the degree to which the smelter, and the furnace in particular, is amenable to total automation. Due to the problems peculiar to a smelter, it is unlikely that a fully closed loop system could ever be achieved and that the smelter will continue to depend upon extended manual control supported by computer based information sorting and optimisation.Generally, loop control is performed using Taylor's Mod III process control system. For distinct plant systems involving a combination of process loops, sequencing, and data acquisition, the company has developed its own microprocessor based systems. Process optimisation using computer based analysis of operating data is well established. Utilising this data, computer modelling provides manual set point supervision for the furnace process control system.The impact of automation on the workforce and on operating costs is also examined. Predictions on future developments in the field of automation, optimisation and sequencing are propounded and related to the non-ferrous industry at large.

Jan 1, 1985

By Morrell S

As more and more autogenous and semi-autogenous mills are run in closed circuit with cyclones the limitations that can be imposed by poor grate and pulp lifter design are becoming increasingly apparent. Relevant literature on the subject is al

Jan 1, 1997

For effective backfilling, a system with the 13 features covered under the section: effective backfill systems, is required. Effective backfilling cannot be done with systems that are badly designed, outdated or overextended. But in cases where the requirements for effective backfilling are overlooked, the shortcomings of such systems may wrongly come to be regarded as limitations to the capabilities of backfilling per se. Mining is currently done to depths of 3500 m, and is to go deeper since the gold-bearing reef extends down to 4000 m and 5000 m below surface. Effective backfilling systems will be required at such depths, and with suitable design this can be achieved. Mining the narrow tabular orebody of a typical South African gold mine is described at the start of this paper, then cycloned backfilling is discussed in general, and its effectiveness (most of the fill placed in South Africa is cycloned backfill or ædeslimed tailingsÆ).

Jan 1, 1998

By J C. Macintosh

Capcoal Mine has modified its water use practices over the past 15 years. Two issues have changed the way water was managed:an economic review of water supply options for a planned expansion of the coal handling and preparation plant (CHPP) in the early 1990s, and increasing neighbour concerns about discharge of worked water from the mine into the local streams. These issues resulted in commitment by the site General Manager to cease discharge of worked water from site and to convert from using raw water to worked water in the CHPP. Operational needs, societal demands and continuing dry weather are again demanding change to the siteÆs water management strategy. This paper outlines the drivers for past and future operational change.

Jan 1, 2006

By Stein A

The general mechanism of recrystallisation for cold worked metal is well established, and need be only briefly summarised with a few references to recent articles which clarify minor points. The types of extension, whether by stretching, drawing, hammering, rolling, etc., do not alter the general principles (1), although quantitative results may differ somewhat, particularly with regard to differences between the surface and interior of samples.These principles can be summarised as follows: The first stage in annealing is a recovery (sometimes known as relaxation) of physical properties such as hardness, elongation, etc., without any appearance of recrystallisation; the second stage involves a further alteration in physical properties, accompanying the formation of new recrystallised grains which replace the original structure; a possible third stage involves an increase in the grain size of the completely recrystallised structure by absorption of smaller grains by larger ones. These three stages will be referred to as recovery, recrystallisation, and grain growth. Depending on conditions, the three stages may be clearly marked or may occur more or less simultaneously.For a given annealing temperature, cold deformations below a certain amount fail to give recrystallisation, and the final structure consists of the original grains which have recovered and possibly become more equiaxed. When a certain deformation, critical for that annealing temperature, is given, recrystallisation can occur, and will give the maximum recrystallised grain size.Increasing deformations beyond this give progressively smaller grain sizes.For each material there is a minimum recrystallisation temperature, below which recrystallisation will not occur whatever the deformation or time of annealing. For a given deformation there is a temperature, critical for that deformation, below which recrystallisation will not occur, and above which it will take place with increasing rapidity.

Jan 1, 1947

By Collier D

The topaz resource at Torrington in northern N.S.W is currently the subject of a joint research and development programme managed by Pacific Copper Ltd, This programme has culminated in a pilot topaz calcination plant, located at Parramatta, which, through its operation, will establish the commercial viability of developing this mineral as an industrial raw material for both the refractory and fluoride chemical industries.

Jan 1, 1989

Organic dyes such as nigrosine and sun yellow act as depressants for carbonaceous particles in the, flotation of sulphide ores. Depression is achieved when initially hydrophobic organic surfaces are made hydrophilic by preferential adsorption of dye molecules. Experimental studies, mainly on Mount Isa ores, indicate that dyes are adsorbed as planar anionic micelles attached to carbonaceous surfaces by van der Waals and ion exchange attractive interactions. Relationships appear to exist between the amount of organic matter on the surface of ground particles, the surface area of the particles, the "saturation" adsorptions of dyes, and the degree of difficulty experienced during froth flotation.

Jan 1, 1975

By Russo S

Metals Refining Operations Pty Ltd (MRO) began refining gold in PNG in 1991 and has undergone continuing growth since then in servicing an everchanging and growing market. MRO's ownership combines PNG Government interests and Golden West Refining Corporation Limited as operator.Features include a very diverse range of suppliers, a full range of technical methods and challenges and the financing and marketing responses unique to a developing country. These areas are examined and documented with special emphasis upon the service needs for the gold industry and future trends and challenges are discussed.

Jan 1, 1997

By B Wiggins, M Russell

Off-gas handling systems are a critical component of modern metallurgical furnaces and typically represent as much as 50 per cent of the total installed smelter capital cost. Inadequate off-gas system performance, due to insufficient exhaust flow or excess maintenance downtime, can present a serious process bottleneck and limit smelter production rate. Therefore, it is essential that the relevant performance issues are fully understood and considered in the design of these systems, particularly when combustibles produced within the furnace must be combusted or handled in the off-gas system. This paper examines the requirements, design issues, and conceptual design process for state-of-the-art postcombustion off-gas systems. The relevant design considerations of safety, environment, energy consumption, and maintenance are presented, and the relative importance of these key issues are compared and discussed. The benefits of using computational fluid dynamic (CFD) modeling in the design process at the conceptual design stage are also demonstrated. Finally, the design basis and performance of a recent Hatch-engineered system currently in operation is evaluated.

Jan 1, 2002

By Misk A

Several logging methods are presently available to the oil industry for the evaluation of formation porosity: the Sonic and Neutron logs are already widely used, the Gamma-Ganmia log is being progressively introduced. The readings of these instruments are primarily a function of the rack-porosity, hence the general term of "porosity tools". Apart from porosity, however, other variables such as type of fluid in the pores, nature of matrix and degree of shaliness have an important influence.The response of each device is a different function of such parameters: therefore, a cci bination of porosity tools can lead to information on these variables in addition to the evaluation of effective porosity.For example, the presence of gas; rather than water or oil, in a formation which is not deeply invaded, will tend to give Neutron derived porosity values which are too 'low; on the other hand, the Sonic derived porosity: value will be too high in such- a case. For the same porosity, the Sonic gives a longer transit time in sandstone than limestone, whereas in the low porosity range, the Neutron will read more counts per second in a sandstone than in a limestone of the same porosity. The presence of shale also affects the readings of the various porosity tools in different ways so that the combination of two or more methods may lead, in some cases; to an evaluation of both the-effective porosity and the shale, content.In conclusion, it may be said that the various porosity tools pre-sently available, are, to a large extent, complementary, and that in many problems the use of two porosity tools, instead of one, is very likely to bring valuable additional information.

Jan 1, 1962

By G C. Reed, J M. Murray

During more than 100 years continuous mining of the lead-zinc orebody at Broken Hill, an immense amount of geological data has been collected about shear zones related to the orebody. The challenge to current mine geologists is to synthesise and interpret these data sets in a way that is applicable to production demands. Precise knowledge of the locations of major shear zones is important not only for the determination of ground conditions but also to develop an understanding of ore remobilisation along these structures. Traditionally, geological information has been collected from drill core and back and wall mapping underground, and interpreted on sections that are approximately 20 m apart. The recent introduction of MaptekÆs Vulcan software has enabled the shear zones to be modelled in three dimensions. The new three-dimensional shear models have been combined with seismic data from the Southern Cross area. The seismic data is collected from a microseismic monitoring system installed in the Pasminco Southern Operations in August 1996 (Rauert and Tully, 1998). The addition of seismic information to the shear zone models has led to a greater degree of certainty about the shear zone locations and has provided information about shear zones in areas yet to be drilled.

Jan 1, 2000

Activated carbon is ideally suited to treating low grade ores and tailings by the carbon-in-pulp process and is rapidly replacing the use of zinc for recovering gold from cyanide leach solutions. Coarse carbon particles derived from coconut shell adsorb up to 30,000 ppm Au as a gold cyanide complex and can leave barren solutions containing

Jan 1, 1982

By Nyamekye GA, Subramanian S

Adsorption tests have been carried out to elucidate the interaction mechanism between dextrin and sulphide minerals. Sulphides such as galena and heazlewoodite exhibit high affinity adsorption over the pH range that coincides with the iep of lead and nickel hydroxides, and is suggestive of chemical interaction. The adsorption behaviour with respect to the sulphides of copper is of the low affinity type, and follows a different pattern. The adsorption studies on graphite, support the chemical interaction mechanism, with the metallic impurities serving as adsorption centres. In conformity with the proposed mechanism selective separation of galena from chalcopyrite and heazlewoodite from chalcocite has been Achieved.

Jan 1, 1993

By Lin Bin, Qain Minggao, Qu Qundi, Yao Zhichang

This paper describes the application of a 89C52 chip microcomputer in hydraulic pressure information monitoring system of powered supports in a coal face, and the details of circuit and software of a monitoring system substation. Each substati

Jan 1, 1998

The first grant of land rights in Australia was pursuant to the Aboriginal Land Rights (Northern Territory) Act 1976. That Act has been at the core of the dispute between land rights and miners' rights. The mining industry believes that the Act, in giving a right of veto to Aborigines with respect to exploration and mining on Aboriginal land, has been responsible for a stagnation in exploration amd mining activity in the Northern Territory. In February 1985 the Commonwealth Government released for public comment its preferred model for national land rights legislation. The model has been opposed by the mining industry because it believes, first, that land rights is a matter which should be left to the States and, secondly, that the detailed mechanisms contained in the model constrain the industry in the manner of the Northern Territory legislation. Aboriginal leaders have opposed the model because it does not, in their view, measure up to undertakings given by the Commonwealth Government and, in addition, it provides for amendments to the Northern Territory legislation which are likely to result in the loss of the Aboriginal veto right. Are land rights and miner's rights compatible? The answer is yes provided all parties, including Governments, are prepared to talk and compromise and Governments recognise that the grant of land rights and any control by the Aboriginal people of exploration and mining on their land is not a substitute for raising the living standards of Aborigines as a significant group of disadvantaged Australians.

Jan 1, 1986

By E Kabwe, E Chanda, M Karakus, S Akdag

The Convergence Confinement Method (CCM) is one of the frequently used methods that considers the ground response to the advancing tunnel face. The CCM analytical solutions represent stress relaxation on circular tunnel walls in a rock/soil media. The CCM analytical solutions is based on circular tunnel geometry and consider a hydrostatic stress field in a homogeneous isotropic rock mass condition. However, noncircular tunnel geometries, non-hydrostatic stress field, staged excavation process in a discontinuous anisotropic non-linear rock mass conditions are usually ignored in these analytical solutions. In this paper, we investigate the performance of the existing CCM analytical solutions developed for elastic and elastoplastic ground behaviour for circular tunnels. For this purpose, a finite difference analysis is conducted to compare the analytical results with the results obtained from Finite Difference Method (FDM) for a chosen rock mass condition. Results obtained from the investigation shows that floor, crown and wall displacement are 30%, 10% and 23% more, respectively, in a horse-shoe relative to a circular tunnel. This indicates that the application of analytical formulation tailored for circular tunnels would lead to inaccurate quantification of wall convergence in horseshoe-shaped tunnels. CITATION:Kabwe, E, Karakus, M, Chanda, E and Akdag, S, 2018. Investigating the tunnel closure using convergence confinement method and 2D plane strain finite difference analysis, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 152–159 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By W Lu, D Wang

Study of coal oxidation at low temperatures forms the basis of investigating the inherent properties of spontaneous combustion of coal. In general, the process of coal oxidation at low temperatures is very complex, involving many factors. Experiments examining the properties of oxidation and ignition of coal have been carried out. Based upon the results of these experiments, the catastrophe properties in the process of coal oxidation are analysed and the mechanism of catastrophe is proved for the ignition of coal. A folding catastrophe model is also established for the process of coal oxidation. Results obtained show that the process of coal oxidation to ignition is discontinuous, where the coal-environment system yields structure destabilisation. The system can jump from one stable attractor to another. The research results presented in this paper help to show the irregularities of coal oxidation at low temperatures and how to pursue effective control measures.

Jan 1, 2005

A three-dimensional finite element analysis is used to determine the stress intensity factors associated with the chevron-notched semi-circular bend test specimen. The stress intensity factor calibration is done over a range of crack lengths a

Jan 1, 1998

By S Worden, P A. Kirsch, A Kirsch

Despite the current downturn, coal remains an important commodity in the Australian economy. Increasing coal resource development has resulted in increasing competition for land use in coal mining regions across the country with communities and other stakeholders becoming more adept at articulating their concerns regarding this competition in a range of traditional and social forms of media. In this environment, obtaining and maintaining a social licence to operate (SLO) is problematic and has been identified as the fourth greatest risk facing the international mining industry.This research presents the findings from a longitudinal study on how Australian newspapers frame the views of coal mining stakeholders across each stage of the coal mining life cycle. News stories from national, state and regional newspapers in 2000, 2006 and 2013 were analysed.Over the study period, there have been significant changes in the coal mining themes being covered by Australian newspapers, the number of stories being published, the number of newspapers covering coal mining stories, and the diversity of stakeholders being quoted. How do the dominant themes in media communication change over time? How do these changes impact mining across the life-of-mine?The research confirmed that Australian journalists use framing, priming, labels and bias to conceptualise and understand the events that they report, and that this behaviour has a profound effect on public opinion.CITATION:Worden, S, Kirsch, A and Kirsch, P A, ?2014. Moving beyond economic framing of the Australian coal industry, in Proceedings Life-of-Mine 2014 , pp 365–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

The major slime forming minerals in coal seams are generally montmorillonite, illite and kaolinite, and due to the consistant trend to full seam mechanisation in New South Wales and Queensland these minerals remain in the feed to a coal preparation plant. After coming into contact with water their size degradation is very rapid, and therefore they mostly report to the fine coal cleaning section of the plant. Froth flotation, being the most effective method of beneficiating fine coal, is widely practised in these two major coal producing states of Australia. Plant experience and laboratory tests suggest that the presence of these slimes in the flotation circuit depresses the flotation of fine coal. Although the deleterious effects of slimes on the flotation behaviour of minerals is well known, the mode of their adsorption at the mineral surface has been a subject of controversy for some time. In this paper, on the basis of the surface properties of slime forming minerals and coal, a model has been put forward to explain the adsorption of slimes at the coal surface. The degree of slime coating has been examined by scanning electron microscopy. Laboratory tests have revealed that with the appropriate use of polyvalent phosphate electrolytes these slimes can be liberated from the coal surface. Just attrition and desliming are not enough to ensure complete liberation of slimes. Coal, after treatment with these electrolytes and then deslimed, floats readily with a common frother, such as MIBC. Modifications in the conventional flotation circuits have been suggested to ensure an efficient flotation of fine coal.

Jan 1, 1978