Search Documents

By Evans A. F

Arising out of the increasing demands for efficiency in modern ore-dressing operations has grown a requirement for fuller knowledge of the characteristics of the ore treated. In part, this is being met by improved methods of study of the mode of occurrence of the constituent minerals, and of the intricacies of their physical relationships.A typical instance of the need for such a study is the presence of some undesired mineral in a flotation concentrate or tailing, which may be due either to mechanical association through insufficient grinding, or to incomplete separation in the flotation operation.Again, with modern practice in fine grinding, which often requires that from 70% upwards of the ground ore shall pass a 200-mesh screen, it is obviously impossible to obtain data on comparative grinding efficiencies, for instance, unless there is adequate knowledge of the size-composition of the material passing the finest available screen.Studies like these can be made satisfactorily only after size-separation (which may be carried out conveniently by elutriation) and by actual visual examination with the aid of a microscope, and the minute size of the mineral grains to be examined has necessitated the development of a new technique of sizing and microscopic examination.

Jan 1, 1932

By Bogar D. V

Often dewatering of coal tailings is inhibited by the presence of clays, making it difficult to obtain a high concentration, handleable coal tailings. The net result can be a low concentration, chocolate mousse-like tailings which poses significant sedimentation problems in a tailings dam and represents a significant environmental problem. This paper examines the coal tailings from a Hunter Valley colliery where the tailings properties are influenced significantly by the presence of montmorillonite clay. The influence of the calcium ion on the rheology and sedimentation/compression behaviour of coal tailings . containing montmorillonite already dispersed in water was investigated and revealed that very little improvement in the properties is achieved through the coagulation. The preliminary investigations also indicated that the properties of the tailings were dominated by the presence of the montmorillonite clay. Thus investigations were carried out on the clay alone in water. Investigations into the effect of dispersing samples of the clay alone in water and then coagulating with calcium compared with dispersing the clay directly into calcium ion solutions at the same calcium concentration showed huge improvements in the rheology, compressibility, sedimentation rates and sediment solids concentrations for the second dispersion method, which can be called controlled dispersion. The sediment volume fraction solids improved by more than a factor of two by controlling the dispersion of the clay. The reason for the improved properties lies in the suppression of the initial swelling of the clay, which is initially in the sodium form, thus maintaining the parallel orientation of the platelets that is present before wetting. While swelling is being suppressed, ion exchange occurs with the calcium which results in permanent swelling suppression. In the uncontrolled dispersion case where swelling is uninhibited, the clay is allowed to break up and despite the powerful coagulating nature of the calcium ion, the random orientation of the high aspect ratio clay platelets inhibits effective coagulation. Results indicate that the initial electrolyte concentration of the washwater in a coal washery is the critical factor controlling the dewaterability of clay tailings and the handleability of the dewatered product rather than the actual act of coagulating with the calcium ion. The results presented are of clear practical significance and indicate how coal tailings problems where clay dominates the rheology can be improved considerably by knowledge of the surface chemistry.

Jan 1, 1995

The Golden Pig Mine is wholly owned by Bunnine Operations Limited and is located in the Yilgam Goldfields at Southern Cross, Western AustraliaThe paper briefly describes the geology and history of the operations. Mining is by shrink stoping, both hand held and mechanised. Advantages and disadvantages costs of the mining system are discussed.

Jan 1, 1993

This paper reviews the geochemistry of weathered nickeliferous sulphidic and lateritic profiles, the supergene behaviour of nickel and ore-associated elements, and their implications for exploration in an attempt to distinguish between barren and mineralised nickeliferous profiles. Nickel is an abundant accessory element in ultramafic rocks with background concentrations in some units up to 0.25 weight per cent. Ore-grades in fresh rock are mostly associated with massive and disseminated sulphide zones within magnesium-rich layered ultramafic sequences. In lateritic weathered terrain, nickel is also concentrated in the regolith profile. This process not only upgrades nickel in the gossanous weathered product of sulphidic deposits, but for sub-economic sulphide zones and some ultramafic rocks, is sufficient to result in a supergene resource. Ore-grade accumulations of nickel in regolith after sulphide-poor ultramafic rocks are referred to as lateritic deposits. Nickel sulphide zones and their ferruginous weathering products are collectively referred to as sulphidic deposits and are the major source of nickel in Western Australia. Mineral exploration in the Yilgam Block is hampered by deep lateritic weathered profiles (eg Butt and Sheppy, 1975; Smith, 1977; 1982). During the nickel boom of 1967 - 1972, most discoveries resulted from the location of outcropping nickeliferous gossan and ironstone. Exposed ultramafic terrain with nickel sulphide potential were explored intensively, mostly by gossan and soil sampling. However, up to 85 per cent of the area of the Yilgarn Block is buried by transported regolith. In these covered areas, barren and mineralised rock responses at the surface are similar and soil sampling produced unreliable results due to many false anomalies. A statistical, multi-element approach to regional geochemical exploration has evolved. Potential trace element indicators investigated, include Co, Cr, Cu, Ir, Mn, Pb, Pd, Pt, Sc, Se, and Zn. In recent years, trace element ratios have also been tested with varying degrees of Success.

Jan 1, 1996

By Corbett GJ

Comparisons between individual SW Pacific Rim gold deposits have facilit-ated proposal of a new classification of porphyry-related mesothermal gold deposit types. Carbonate base-metal gold systems form at relatively high crustal levels, peripheral to porphyry intrusions. There is a spatial assoc-iation with major structures which focus fluids from degassing porphyries at depth. Milled matrix intrusive breccias and extrusive maar volcano/ diatreme breccias form as a result of pre-mineralisation phreatomagmatic eruptions. These focus degassing magmatic fluids by the provision of fracture ground preparation, typically within competent host rocks, adjacent to the breccia bodies. Local dilational structures control the form of individual deposits which may contain bonanza gold grades at sites of fluid quenching and/or repeated mineral deposition.Early quartz veining and porphyry-related alteration is common and later gold mineralisation typically occurs in association with carbonate veining and Fe and base metal sulphides as Zn > Pb > Cu. The progressive cooling by mixing of the upwelling mineralised magmatic fluid with descending bicarbonate waters, produces characteristic zonations in carbonate compositions. These vary with distance from the porphyry source, from Ca through Mg, Mn and distal Fe types. Gold mineralisation is preferentially distributed within the Mn/Mg carbon-ates.

Jan 1, 1994

By Blair J. R

A Train Performance Calculator (TPC) is an essential tool in railway operations, as a means of acquiring quickly a precise measure of the performance of the system. Traditionally the TPC was used in the form of program for a large computer. By employing an efficient integration algorithm and tailoring the program to suit the computer system it is shown that it is possible to devise a TPC for a mini computer. The resulting low running costs and flexibility of operation makes this a useful design tool. This TPC was developed to study problems associated with a single track railway operation. It was applied specifically to study the railway operated by the Mt. Newman Mining Co. Limited in the Pilbara region of W.A. to transport iron ore from the mine to the port. The TPC was used to calculate the effects of changes to locomotive power, to train size, to the track and to the amount of traffic. Its accuracy was checked by comparing its performance with that of the actual trains.

Jan 1, 1977

By Kovscek P. D, Thimons E. D

The Bureau of Mines equipped a longwall shearer with a water- jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 1 MPa and with water-jet-assisted cutting pressures ranging from 7 to 40 MPa. At water pressures of 20 MPa and higher, dust concentrations were reduced by as much as 85 % via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1988

By Sheng X. L

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts. collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger..

Jan 1, 1992

By Dorricott M. G, McAllister J

This paper is concerned with the application of a probabilistic approach to the risk assessment of mining projects.In current practice, sensitivity analysis is the most commonly used deterministic approach of accounting for the uncertainties involved in mining project evaluation, while Monte Carlo simulation is considered to be the best probabilistic method available for the same purpose. The methodology of the approach proposed in this paper is as simple as that of sensitivity analysis. However, the results obtained can be more comprehensive than those obtained from Monte Carlo simulation. Various important statistical features, such as correlation and skewness, of the basic random parameters can be easily taken into account by the proposed approach. Example studies are demonstrated. Lotus 123 was employed for the associated probabilistic calculations.

Jan 1, 1992

Large GDP increases in the Pacific Rim countries have been accompanied by similarly large increases in demand for oil products. In the case of residual fuels, this demand has been tempered by the substitution of other energy products such as coal or gas.In the region's developing and newly industrialised nations, it has not been possible to make the very large investements in infrastructure which allow other energy sources to be used for transportation. As a result, GDP growth has been mirrored in the demand growth for automotive fuels. Other non-sustitutable products such as lubricants have also benefitted by the region's GDP growth.The combination of a number of years of sustained growth, coupled with increasing quality requirements is now stretching the upgrading capacity of the region's refineries. If, as seems likely, the region continues to enjoy a high GDP growth rate, then this will be accompanied by increasing reliance on finished products coming out of the Middle East. The owners of the most simple form of refinery in which crude is simply distilled and the naphtha reformed into petrol will face major capital investments. If they decide not to bear this cost, they will face increasing problems in selling their surplus residual fuel oil at an economic price. Quality will become an increasingly important issue. Not only in the well publicised areas such as unleaded petrol, but also for products such as lubricants which play a major role in the efficiency of modem equipment. Quality of service such as hours of opening, ease of access, and service station facilities will also become increasingly important as the oil companies use these to attract customers and gain brand differentiation.

Jan 1, 1990

By Aspinall T. O

Draglines have found wide application in strip mining coal seams down to 60m depth. A research Project funded through NERDDC has been underway during the past two years investigating the application of large draglines loading overburden into hoppers feeding into conveyor systems or off-highway trucks. This paper presents the preliminary results of these investigations and covers overburden characteristics, bucket spotting con- trol, bucket design, conceptual hopper systems, system application at representative mine sites, and broad process comparison. The studies have initiated new concepts in the extended use of draglines at deeper strip- ping depths. Alternate arrangements for dragline bucket rigging and bucket control aspects of dragline stripping operations offer productivity improvements. Extended use of existing draglines includes, draglines dumping into hoppers which feed large trucks or conveyors, trigger dump buckets rigging arrangements, and rear dump dragline buckets with integral grizzly bars. The paper details these suggestions, and points to specific areas where the most productive applied research is anticipated. Mine planning considerations detail the factors involved in selecting dragline bench heights in association with hopper operations.

Jan 1, 1989

By Ohga K, Isobe T

Basing upon many and long practical experiences of gas drainage from coal seam and results investigations on the gas flow through in si-tu coal seam using tracer gases,it became clear that solid coal itself is hardly gas permeable or has extremely low gas permeability. Almost all of gas flows from a coal seam into boreholes through fracture net- works intersecting with them.Primary and secondary fractures in coal seams differ in their size and continuity from place to place according to differences of the coal strength and the stress conditions. A lot of gas can be drained through boreholes which intersect with many and/or wide fractures. A mathematical model for gas flow from a coal seam to a borehole through a discoidal fracture is proposed. From the numerical analyses,the apparent radius of the discoidal fracture in this model is shown to be a good indication of the gas drainage ratio. In addition to this,an atempt to make fractures around a borehole using high velocity water jet(ca.lmm dia.,300-700atm., 100-200 1/min.) is introduced.

Jan 1, 1982

By Reid T. W

This paper describes the results of investigations into the relationship between specific gravity and chemical composition in the Cockatoo Island orebody, In the early investigations the samples were classified into groups according to porosity. This resulted in high, medium and low porosity groups, the latter being further subdivided into ore and waste. Whole number tonnage factors were assigned to each group. In the later investigations the reciprocals of bulk specific gravity and true specific gravity were ex- pressed as linear combinations of iron, silica and alumina using stepwise regression. The efficiency of the models as predictors was tested by dividing the data into two sets; one of which was used to calculate the regression equation and the other to test the efficiency of the equation as

Jan 1, 1976

Australis Mining N.L. operates a continuous mode carbon-in-pulp (CIP) gold plant, processing sand and slime tailings from previous gold mining operations in the Norseman area. Plant design is that of conventional countercurrent contact between pregnant pulp and activated carbon. Gold desorption is achieved by the Zadra process using near boiling tempera- tures and atmospheric pressure. Process water is drawn from nearby Lake Cowan (saline). The plant operates at, or above, design specification of 400 dry tonnes per day. This paper describes the plant design and operating processes utilised in optimising throughput and gold recovery. TNTDnPTTnmTnM Favourable world gold prices and substantial reserves of sand and slime tailings prompted Australis Mining N.L. to construct a gold extraction plant during 1981. The projected plant throughput was set so as to complete treatment of available tailings over a three year period. Metal- lurgical tests indicated that, with a regrind facility satisfactory gold recovery could be achieved using a countercurrent CIP process. Reflecting the entry of Australis Mining N.L. into its first large scale treatment operation, the plant design emphasised simplicity but effectiveness of Operation.

Jan 1, 1982

By Zharinov SE

Geonechanical modelling of island arc sys- tems and their analogs is investigated. Slow seismotectonic movements along the inclined deep fault zone under the compressive horizontal stress conditions are proposed to be the princi- pal mechanism controlling the structures and processes in the active continental margins. A model of shearing surface crack in an elastic half-plane is used for simulation. The main ele- ment of the model is viscous interaction bet- ween the crack sides, the viscosity varying with depth. To describe the stress-strain state of the medium an integro-differential singular equation is derived and solved numerically. The results of simulation are in good agreement with geological and geophysical data on the ac- tive continental margins.

Jan 1, 1987

Geochemical investigations carried out in the Woodcutters area, Rum Jungle district, NT., consisted of a programme of C-horizon soil geochemical sampling followed by rotary-percussion and diamond drilling.Comparison of detailed geochemical sampling with the original broadly-spaced sampling showed that the structures along which the orebodies occur are reflected very closely by the detailed sampling.A series of vertical rotary-percussion drill holes put down adjacent to a gossan revealed a broad layered dispersion of lead and zinc in the deep lateritic weathering profile, while primary dispersion haloes are only very narrow. The layering appears to be related to the weathering profile.

Jan 1, 1978

By Durucan S

Uncertainty due to spatial and temporal variability of different pollutants found in soil, water and air is an important issue in the modelling of environmental impacts. Recognition of spatial environmental patterns is relatively straightforward to achieve by applying most of the well-known artificial neural networks or adopting a stochastic approach. However, it is the temporal component of the environmental variables that makes modelling of the environmental pollutants particularly complicated and challenging. This paper presents the results of a case study investigating the artificial neural network performance when modelling the spatio-temporal behaviour of environmental pollutants. The test case involved the modelling and prediction of the distribution of water quality indicators along a river from the point of discharge of treated mine effluents. The behaviour of river water quality indicators is rather complex and shows a lot of fluctuations due to a number of hydrochemical, hydrobiological and hydrodynamic factors. Results obtained in this study indicate that artificial neural networks provide a very powerful and robust method for simultaneous modelling of spatio-temporal behaviour of environmental pollutants.

Jan 1, 1995

By Fowke NC, Williams RJ, Hungerford F

In-seam, directional drilling has been implemented at Huntly West Mine, New Zealand as the most cost effective means of obtaining geological information at a level of detail and accuracy required for planning of longwall ("flexiwall") panels. No geological or geophysical technique tried at the mine prior to 1989 has been able to reduce geological risk to an acceptable level. Surface and in-seam seismic methods have not had adequate resolution. Obtaining the required knowledge via surface drilling would be prohibitively costly, and still not precisely locate or orient faults or the axes of seam "ridges and valleys".A total of 3543 m was drilled at an average of 67m/shift including setting up time. Unplanned delays totalled only 9.6 percent. Major re-interpretation of seam structure resulted from the drilling. Lateral and longitudinal panel grades have been defined. which should be negotiable with the Coalcorp longwall equipment.

Jan 1, 1991

The problems encountered with the introduction and use of Isanol underground are described. Significant direct as well as indirect savings have resulted from the use of Isanol. Field studies have shown that the concentration of common gases released during detonation is considerably lower than with conventional nitro-compound type of explosives.

Jan 1, 1977

Total extraction is a misnomer and invariably some coal losses occur in the mining of pillars. "Fulls" pillar extraction is by the pocket and fender method, the splitting method or the open end method, with extraction in the pillar, and in rows of pillars in planned sequence, using combinations of coal and timber and roof-bolts for support. Where circumstances dictate, partial extraction is used, leaving behind portions of pillars in large blocks for support. The use of such extraction plans and supports as minimum guidelines has contributed greatly to safety in United States Coal Mines.

Jan 1, 1974