Search Documents

The cost-effectiveness of blasts involving radiating blastholes is cur- rently restricted in the following ways. (a) Significant percentages of potential explosion energy are not being liberated; the collar sections of some charges are being dislocated and/or desensitised by the detonations of adjacent earlier-firing charges. (b) If the minimum charge spacing is too small, detonation of an early- firing charge can initiate an adjacent charge sympathetically, thereby eliminating the benefit of any intended inter-charge delay. (c) The overall distribution of energy is poor. Appreciably better fragmentation would be achieved if current drill- ing patterns were to be replaced by staggered fans/rings having a toe spac- ing : burden ratio of about 4 : 1. This wide-spaced pattern would enable a higher percentage of the potential energy to be released, would reduce the incidence of sympathetic detonation and would provide a superior overall distribution of this liberated energy. If improved fragmentation is not required, the proposed fan/ring design should allow a significant expansion of the blasthole pattern with consequential cost savings in drill- ing, explosives and initiation.

Jan 1, 1988

The mined-out Old Waite volcanogenic Cu-Zn deposit lies in the Noranda mining district of northwestern Quebec. The deposit has a distinctive pipe-like zone of alteration beneath the massive ore, extending into the stratigraphic footwall. The hydrothermal metasomatism within the alteration pipe produced a concentric zonation. with a peripheral quartz - sericite - chlorite mineral assemblage surrounding an axial core of magnesian chlorite - Phlogopite.

Jan 1, 1989

The mine planning and operational aspects of applying Continuous Surface Miner (CSM) technology to Australian coal strip and open cut mines is investigated for both existing and planned deposits. CSM produc- tivity as a function of geomechanical properties, formation thickness, mechanical availability and in-pit physical constraints, are considered. Productivity and operational costs are derived from current production machines and from first principles.

Jan 1, 1989

By Sinha DK

Coal Mining in India had been confined in the past primarily to two or three coalfields. Unscientific mining has led to huge degradation of land including massive subsidence of strata and disturbances of water tables to a wide extent. This has caused problems not only in flooding of mines from surface water but also in further planning of the surface drainage for current mining activities. Now, therefore, surface hydrology and land-use potentialities of the area have been endangered inflicting severe damage to the overall environment and ecology of the area. The paper Discusses certain investigative aspects of the problems highlighted as above in one of the coalfields, and encompasses mainly the following areas : 1) Quantitative estimation of the damage already done to the natural surface drainage system. For this purpose damage to topography and drainage for the last fifty years have been made out through the aerial photographs and topographic map sheets 2) Analysis and comparison of different states of such photographs are carried through to indicate the extent of damage to the hydrological conditions inducing undesirable changes in its land-use pattern. Based on the analysis, concrete suggestions are made to restore the water drainage system which will be most suitable for future mining in the area containing high grade coal. The design and planning of the drainage system is based on the total system approach including the cost benefit analysis as well as hydrological considerations.

Jan 1, 1988

In the early ages man contented himself with the use of such tools and appliances as would assist him in the enlightenment of his labours. With the advancement of science, numerous motives, with modifications and adaptations, have been introduced to enlighten labours, and in many cases have taken the place of man, but it can hardly be said that this applies to shovels, although one of the oldest implements of labour; certainly, with the introduction of the steam shovel the labours of man have been considerably reduced, but the hand shovel of today is used similarly to that of years ago.If the principle of the hand shovel has not been improved upon, it must not be suggested that the manufacturers of this article are not endeavouring to improve its quality, and the main point with which the manufacturers have to contend is the production of an article which will give a maximum of durability combined with a minimum of lightness. In order to accomplish this they must select suitable material, and subject it to such heat treatment process that will produce a shovel having a maximum of hardness and toughness without being unduly brittle, and which will withstand the excessive wear to which it is subjected.In this article an endeavour will be made to explain (a) the manufacture of shovels; (b) the defects commonly met with-the cause of same and measures which are necessary to remedy them.Before doing so a brief description will be given of the class of steel used for shovels; this is an important factor, and a steel which is admirably suitable is a plain carbon one containing approximately 55 - 70% C., and closely resembles that used for the manufacture of railway rails. This plain carbon steel is very extensively used, although at present alloy steels are being utilised to a certain extent for shovel manufacture, and with suitable heat-treatment.

Jan 1, 1926

By R K. W Merkle, E Whiteman

The anorthosite complexes and related rock types of the Indian Precambrian shield are primarily associated with either cratons or mobile belts. They were metamorphosed under amphibolite to granulite facies conditions. The major rock types are chromite-bearing meta-anorthosites, amphibolites, basic granulites, pink granites and gneisses. This study was carried out on chromitite bearing samples from Sittampundi Anorthosite Complex (SAC), Tamil Nadu, to evaluate the nature and textural settings of platinum-group minerals (PGM), using state-of-the-art technology. The structure and petrology of SAC were well studied by earlier workers (Subramanian, 1956), but only scanty data on geochemical, petrology and mineralogy of PGM are available. The mineralogy of the samples is dominated by chromite (>70 mass per cent), plagioclase (An90) and chlorite-actinolite with orthopyroxene (En85). Details of the petrological evolution of the Sittampundi complex will still have to be studied further, but indications of magma replenishment at the level of chromite formation and the elevated PGE values associated with the chromitite samples make the Sittampundi complex a promising target for future exploration activity.

Jan 1, 2008

Mineral processing is at the hub of the exploration-mining-metals production system. Because of the large volumes of material processed, incremental technology investments can pay off better than for other parts of the system. However, much of mineral processing remains a 'black art', because we are behind in investing in modem technologies. Consequently, we have one of the best opportunities to improve efficiency and competitiveness through the application and transfer of technologies that have already been developed for other industries. The reluctance of minerals companies to place priority in our area is not because we lack new ideas; our senior management has not been convinced, based on our previous results, that such investments will pay off as well as other investment opportunities competing for the same resources. The key is the proper establishment of technology strategy and more effective transfer of technology. The presentation will identify the failure mechanisms of technology transfer and will present a model for improving the success rate, a prerequisite for raising the priority of mineral processing investment. Topics emphasised include strategy formulation, human resources planning, and total quality management principles applied to improving technology transfer.

Jan 1, 1993

The preconcentration of uranium ore by radiometric ore sorting at Mary Kathleen Uranium Ltd. is described. The operation of the ore sorting machines is discussed in detail and performance results obtained with the existing system are presented.

Jan 1, 1978

The Hartley layered mafic igneous complex within the Great Dyke of Zimbabwe contains economically-recoverable quantities of platinum group metals and gold, nickel, copper and cobalt. The recoverable metals are concentrated in a thin gently-dipping stratigraphic unit - the Main Sulphide Zone. The Hartley Platinum mine, jointly owned by BHP and Delta Gold NL, is scheduled to come on stream at the end of 1996 at an initial mining rate of 2.16 million tonnes per annum and will produce approximately 150 000 oz of platinum and 3300 tonnes per annum of nickel, as well as saleable amounts of palladium (110 000 oz), rhodium (11 500 oz) and copper (2232 tonnes).

Jan 1, 1996

By Rowena C. Duckworth

The Ocean Drilling Program (ODP) is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (legs) which each last approximately two months. These legs are designed by geoscientists from the nineteen countries that subscribe to ODP. Australia and Canada presently share ODP membership under the banner of the AUSCAN Consortium. The benefits of Australia's involvement in ODP include internationalisation of Australian geoscience, advanced graduate training, and unique scientific investigations of the ocean floors in the Australasian region. In addition, visits to Australian ports by the ODP drill ship, the JOIDES Resolution, contribute up to $2 million per visit to the local economy. Amongst the many other aspects of ten years of scientific drilling, ODP has significantly contributed to our understanding of hydrothermal processes on the seafloor. To date, three hydrothermal sites have been drilled to date by the ODP, Snakepit (MAR), Middle Valley (Juan de Fuca Ridge) and TAG (MAR). Two more hydrothermal sites are scheduled for 1996.

Jan 1, 1995

By Kurita K, Tanaka T

In order to clarify the gas flow and motion of coke and reaction in the raceway, the mathematical raceway model was developed. This model consists of the equations of momentum and continuity of gas and coke. The simulated results were compared with the results of the cold and hot experimental model. The relationship between the blast volume and the raceway size, the pressure distribution and the velocity distribution of coke are in good agreement with the experimental results. Moreover the equations of reaction and heat conservation were simultaneously calculated with the dynamic equations. Distributions of gas composi- itions and temperature were simulated and found to be in good agreement with the distributions of gas compositions of CO, CO2 on the tuyere level measur- ed in the hot experimental model.

Jan 1, 1981

The Split Rock low grade copper prospect was discovered in 1969 by Cyprus Mines Corporation using stream geochemistry. Cyprus "Imes carried out geochemical and geophysical investigations, geological mapping, and percussion and diamond drilling, and concluded that the grade of mineralisation was too low (0.1% copper) to be of interest. In the present study, the geology was remapped and very substantial differences from the previous observations are recorded. (lineraliced acid dykes in a 1 000 foot hole drilled by Cyprus Mines had a total inter- section of almost 300 feet with an average crade of 0.4% copper. Surrounding drill holes at distances of 500 feet did not intersect +hese dykes. This group of drill holes occupies a small part of an area about 2 km by 1 km which was affected by intense quartz sericite pyrite alteration along many fractures with an associated soil copper anomaly. It may be that the quartz sericite alteraiion with feeble copper mineralisation represents hydrothermal alteration emanating `rom a mineralised intrusion of which the dykes mentioned above are off shoots.

Jan 1, 1978

During the development of Lorca tunnel project in the South-East of Spain, an in-site study has been done, with the purpose of obtaining the characteristics of the different lithological units through twenty-two parameters for the design of the tunnel excavation and support. In the paper both the different works developed and the different methods and criteria followed in the obtention of the parameters are described. The values of those parameters may be useful in similar cases. Also a summary-table of the parametrical characterization for the use in similar studies is given.

Jan 1, 1987

By Trutwin W, Tracz J

The outbreak of open fires underground cause disturbances to the conditions of the mine ventilation process. Thermal and chemical effects due to fire create unsteady, transient states in airflow and the spread of combustion products in the mine ventilation network. Changes in airflow have an influence on the fire, constituting a sort of feed-back between the fire and the ventilation process. This paper deals with a numerical simulation method, which enables the determination of transients caused by fires. The mathematical model, of the simulation method considered, has been based upon a: simple model of combustion of fuel in the airway, unsteady exchange of heat between the fire, airflow and surrounding rocks, airflow in mine ventilation networks and the theory of heatflow in the rocks. Initial and boundary conditions allow the determination of a set of parameters describing the airflow, the propagation of combustion products, the tempera- ture of the fire and flow etc. due to the fire. The simulation method, facilitates a graphical presentation of the spread of combustion products throughout the network. The simulation method has been prepared for an IBM PC/AT Computer.

Jan 1, 1988

Krupp Polysius AG, FRG, in close cooperation with Prof. Dr. K. Schoenert, FRG have developed the principle of the high pressure grind- ing roll POLYCOM. The POLYCOM mill basically consists of two counter-rotating rolls of large diameter and relatively small width, one of which is fixed and the other moving in slide blocks. The pressure required for comminu- tion is applied via the sliding roll by a powerful hydraulic system. The comminution takes place between the rolls under high pressure in the bed of material by nipping and compacting. The top feed size-depending on the rolls diameter -may be as coarse as conventional secondary crusher feed and the product is a compacted cake containing a high amount of fines created by micro-cracking. The amount of fines depends on the pres- sure (grinding force) applied. Operating results show that even in wet griding circuits capacity increases at downstream connected grinding mills of up to 100010 can be accomplished with an interconnected POLYCOM machine and energy savings of up to 25070 may be achieved depending on application. POLYCOM can be used in existing grinding plants for low-cost upgrad- ing of capacities but also as an advanced alternative to conventional crush- ing and grinding equipment in open or closed circuit configuration. A single industrial size 2.8m roll diameter POLYCOM machine may be fed with top feed size of up to 200mm and produce a finish product as fine- grained as known from rod and ball mills but with less energy consumption. Meanwhile, the POLYCOM high pressure grinding roll has established itself world-wide in the cement industry and is now entering the mining industry. POLYCOM machines are currently designed in industrial standard sizes of 1.0m to 2.0m rolls diameter and drive units of up to 2400 kW. This paper includes: principles of high pressure grinding, main fea tures of the POLYCOM machine, results of tests on various materials including Australian gold and copper ores carried out at the POLYSIUS research centre in Germany. Some examples of industrial applications of high pressure grinding will also be presented.

Jan 1, 1988

An efficient energy management programme can often significantly reduce a company's energy costs. The programme consists of a series of steps, namely a statement of support from senior management, assigning the management team, the energy audit, defining the goals and comwnicating with and training employees. The energy audit provides the information base from which the company can start to control and improve upon energy Usage.

Jan 1, 1983

By Koginmo V. I

The concentrator at Bougainville Copper Limited has an annual throughput of 48.2 million tonnes/year producing approximately 175,000 tonnes copper, 16.1 tonnes gold, and 50 tonnes silver. Conventional three stage crushing and screening are used to reduce run of mine ore to an average product d80 size of 6.7mm. The primary objective of the crush- ing plant is to provide a continuous supply of ore to the 12 primary grind- ing mills via an intermediate 300,000 tonnes capacity stockpile. Since ball mill performance improves with decreasing mill feed size, the crushing plant continually strives to produce the finest possible product for mill- ing. This has been achieved by increasing plant availability and total installed power, and improving crusher manganese liner life, screen cloth life, and plant operating practices. A recent innovation was the installa- tion of a 35 million tonnes/year preconcentration screening plant in Janu- ary 1987 to recover high grade fines from low grade run of mine ore types in which the mineralisation occurs preferentially along fracture planes in the parent rock.

Jan 1, 1988

Environmental considerations were key factors in the design of the Ranger Uranium Mines treatment plant. The mine is located adjacent to the Kakadu National Park and has an average rainfall of 1.6m per annum. Initially, no contaminated water or liquid effluents are to be released from the project area and thus water management is a key design and operating fact. Particulate and gas emission criteria influenced design as did occupational hygiene factors (dust, radon, housekeeping, maintenance access). Equipment selection and engineering standards were conservative and resulted in the plant attaining design performance in less than three months from the date of commissioning. A number of mechanical and operational problems were experienced and are discussed in the paper, however none of these problems have had a significant effect on production.

Jan 1, 1984

The 250 metric tonnes of gold and 360 000 metric tonnes of copper recovered from the Mt Morgan Mine in Central Queensland justify its fame. The mine ceased operation before the advent of three-dimensional computer graphical modelling of orebodies became common practice in mine planning. The Mount Morgan Mine records however remain and are the database for this study. The Mount Morgan project takes ore deposit modelling one step further by examining the relationship between grade distribution within the orebody and key geological features, as a tool for exploration and development.The Mount Morgan gold and copper mineralisation is shown to be strongly lognormally distributed. The deposit has been split into three areas, using geological boundaries, each with different geostatistical characteristics. Important features include: the spatial relationship of near-vertical, high grade shoots with a ring dyke thought to be related to the North Dyke; separation of the high grade eastern stopes from the others along the Andesite Dyke; and lack of concentrated mineralisation along the Slide Fault.Recognition of these features is useful to those currently exploring the Mount Morgan district for similar style deposits, by stressing the importance, or lack thereof, of the geological features.

Jan 1, 1993

The mineralogy of regolith material for which whole rock geochemistry has already been done can be used to better understand/rank the significance of geochemical anomalies. Case studies show that the secondary minerals of the regolith environment have quite different capacities to incorporate pathfinder and target elements, eg hematite appears to be a better host to Pb than goethite and Pb rich alunite-jarosite minerals are a better Ag host than mimetite. Thus correlations between elements in regolith material may be strongly affected by mineralogy. Understanding of the significance of a geochemical anomaly is frequently enhanced by knowledge of the weathering susceptibility of different minerals. For example, when a mineralogical sequence which does not correspond to the expected order is found (eg feldspar overlying weathered material without feldspars) it is possible that transported material is present in the profile. Such mineralogical information is particularly relevant as exploration continues into areas of thick regolith.

Jan 1, 1997