Search Documents

Looking back 25 years, the role of the drill and blast engineer in an Australian mine seemed relatively simple, with the primary focal points being scheduling of the drill rigs, oversize control, and budget control with respect to consumption of both explosives and drill consumables. The choice of explosive selection was relatively simple, though many mines were becoming involved in trials of slurry explosives, emulsion blends, and low density ANFO blends. Guidelines to assist the engineer towards specific fragmentation targets were scarce, environmental constraints were light, and computers were rarely found on the desks of any mining engineers. Wall control blasting was in its infancy, with the bulk of attention being given to appropriate slope design and little real attention given to factors such as explosive distribution, and optimum delay timing and sequencing. Quantitative measurement of blasting performance was rare. The science of blasting, for fragmentation control, wall control, and environmental impact control was about to be born, and was heralded in those years by intense efforts by the explosive manufacturers and a proliferation of research centres throughout the world. Since the early 1980s, the role of the Australian drill and blast engineer has gone through a major metamorphosis, and currently requires a greater depth of scientific understanding than any other specialisation within mining engineering.

Jan 1, 2004

By Blair J. R

In the Bayer process, bauxite is leached with caustic soda, forming a solution of sodium aluminate, from which hydrated alumina is precipitated. The efficient operation of the continuous form of this process requires that the concentration of caustic soda be controlled. A computer simulation of the concentration of caustic soda has been conducted to provide information, regarding the dynamic behaviour of caustic concentration, which is not available from normal plant data. The basis of the simulation is a state- space model of an alumina refinery, linearized about the normal operating condition. The formulation of the model, with the relevant approximations and assumptions, is outlined. The simulation of the mudwash section of the. plant is described in detail. A continuous model of the mudwash, having time-varying coefficients, was driven using operating data from an alumina refinery. The modelled response showed reasonable agreement with the recorded plant response.

Jan 1, 1977

In December 1997, a series of new environmental legislation was enacted including:ò Environmental Planning andAssessmentAmendmentAct 1997; ò Contaminated Land ManagementAct 1997;ò Protection of the Environment (Operations) Act 1997; ò Native Vegetation Conservation Act 1997; andò Pollution Control (Load Based Licensing) Act 1997.These new Acts will have varying degrees of impact on the coal mining industry in New South Wales when they commence later this year.

Jan 1, 1998

Carbothermal Reduction of Ilmenite Concentrates and Synthetic Rutile in Different Gas Atmospheres

Sep 13, 2010

By Christie AB

Stream sediment geochemical analyses from 140 mining company exploration surveys of the Coromandel, Northwest Nelson, Marlborough and Westland regions of New Zealand have been compiled from open file reports and entered on a database called REGCHEM (for Regional Exploration GeoCHEMistry). REGCHEM is supported by GEOEXPL, a custom-written computer software application which operates under the Microsoft Access relational database mangement system on a PC-type computer. The data are plotted as maps using the Maplnfo geographic information system (GIS) package. Thesholds separating anomolous values from background values are determined using the PROBPLOT univariant statistical package, which enables the descrimination and modelling of several populations. Relevant REGCHEM data are being incorporated into a GIS for the Coromandel region as part of ongoing studies to sevelop mineral deposit and metallogenic models for the region, and to assess regional prospectivity.]

Jan 1, 1995

This paper describes a case history of using an integrated geochemical and hydrogeological approach to predicting solute transport from gold mine tailings in highly fractured volcanic terrain. Two modes of transport are identified, namely discrete fissure flow and diffuse seepage through the intervening weathered rock. A simple mass balance approach is used to predict concentrations at points of emergence because most of the seepage migration will be by way of the discrete fissures where advective transport will predominate. The mass balance method has been modified to allow for natural degradation of weak acid dissociable cyanide. The long term effects of diffuse seepage are also examined.

Jan 1, 1988

By S S. Kanchibotla, D La Rosa, R W. Pesch

The Porgera Joint Venture and Dyno Nobel have commissioned a joint project to optimise the drill and blast operations to increase the overall profitability of the mine. One of the aims of this project is to increase the throughput of semi autogenous (SAG) mills by optimising the blast fragmentation. A number of test blasts were conducted during the period May 2000 to January 2002 and the ore from these blasts was campaigned through the mill. The data from these trials suggested up to 15 per cent increase in the SAG mill throughput with high energy blast designs. However, changes in ore geology (shape, structure and hardness) and potential ore dilution/loss and wall damage have raised concerns about the economic benefits of these designs over the entire orebody. The lack of a system to track the economic benefits of these modified designs has also compounded these concerns. PJV and DynoConsult, the consulting arm of Dyno Nobel have initiated steps to minimise the potential for ore dilution and wall damage resulting from these modified designs. DynoConsult worked with Julius Kruttschnitt Mineral Research Centre (JKMRC) to develop and implement a blast management system to track the quality of blast implementation and down stream process benefits. This paper discusses the implementation of the system and the results achieved to date.

Jan 1, 2003

Highwall mining commenced in the Appalachian region 50 years ago. With innovative equipment design introduced in more recent times, penetration distances over 300 m are now commonplace. It is only in the last three years that highwall mining has become part of the Australian coal industry. Geotechnical evaluation is an integral part of the Australian procedures, and although still being refined, has already proven its worth. Statutory guidelines have also been prepared for operations in Queensland. This paper explores trends in equipment design, geotechnical prediction, operating techniques and statutory requirements with regard to highwall mining Australia's coal deposits. A quick assessment guide to assist in the evaluation of potential sites is included.

Jan 1, 1992

Laboratory scale simulation experiments show that the adsorption capacity of Au(CN)Z- on activated carbon in the presence of organic plant contaminants is dependent on the particle size of the carbon. This observation suggests that fine carbon in a CIP contactor can protect coarse CIP carbon from fouling in a dirty CIP plant. A preliminary test of this concept was made using fine lignite coal as the organic scavenger in the presence of the CIP carbon Calgon GRC22 in an alkaline cyanide solution containing Teric 401, sodium ethyl xanthate and kerosene.

Jan 1, 1991

New Zealand's Land and Income Tax Act 1954 contains unique incentives for companies engaged in mining certain specified minerals or petroleum. Sections 152 and 153 provide for the taxable income of such companies to be based not on profits made but on dividends paid to shareholders. A significant saving in tax results, particularly where profits are not distributed: but the Act attempts to ensure that undistributed profits are used for further mineral exploration and development. To encourage investment in the mining industry, persons taking up shares in a company mining for the specified minerals or petroleum are entitled to a one-third deduction in respect of monies paid on the shares and used by the company for its purposes; and company shareholders may make loans to the company and write-off such loans for tax purposes to an amount of up to half their taxable income. Maximum utilisation of the tax incentives calls for careful consideration as to whether a mining or petroleum company should be financed by way of loan capital or share capital.

Jan 1, 1971

By S Pfaff, R Rajic

In the case when the number of independent variables is greater, a careful design for carrying out tests has to be made in order to obtain, with the smallest possible number of tests, as much as possible neutral information about the influence of independent variables on the dependent ones. Only on the basis of such design and its statistical analysis it is possible to come to right conclusions about the function of the whole system. The influence of pressure, temperature, humidity and granulation of the coal upon the resistance to pressure and the water absorption of the briquettes has been tested, with the aim to examine how each of the two dependent variables changes depending on the values assumed by any of the four independent variables and which of the mentioned independent variables significantly influences the dependent ones. The full factorial design with 16 experiments and the central composite design with 27 experiments have been applied. The influence of the independent variables upon the dependent ones has been examined by applying the analysis of variance. The influence values of individual factors and their interaction upon the dependent variables have been stated as well as coefficients of curvilinear equation.

Jan 1, 2003

By M Ruhrberg, J Grassmann, C Bauer

Within the context of acid mine drainage (AMD) associated with mining activities worldwide there has been a tremendous research effort to determine the extent of AMD and assess the influencing factors controlling this process. However, the majority of the current approaches focus on local and regional scale case studies and do not provide a global scale picture of AMD potentials. This study attempts to develop a method aiming at a global environmental impact assessment related to AMD. To confine the complex topic this study concentrates on acidic emissions from heaps in consequence of copper mining processes. In order to pursue this approach two factors are of significant advantage: a comprehensive environmental data base of more then 600 copper sites worldwide and a method which has been developed and proven to be successful in assessing environmental impacts related to land use. Current and future research efforts focus on using this background knowledge to enable both a comparison between sites and a categorisation of sites according to emission estimates.

Jan 1, 2003

By Mitchell M. A

The steeply dipping Mammoth orebody is mined by Gunpowder Copper Limited using a sub- level uphole bench stoping method at a mining rate of 350 000 tonnes per year. of three per cent copper ore. Access to the mine, is provided by 1 in 9 decline which spirals in the footwall connect-, ing all the sublevels, thus maximising mobility and accessibility of trackless mining equipment Sublevels are driven in ore off cross- cuts from the decline every 15 metres vertic- ally. Sublevel drives are stripped out to widths up to 18 metres before cutoff slots are mined at each end. A two boom fan drilling jumbo is used to drill inclined rows of holes to the floor of the sublevel above. Two or three rows are fired at a time which allows broken ore and remnants from the level above to be mucked out by rubber tyred LHD equipment to the brow. Ore widths of up to 80 metres are en- countered at lower levels where ring drilling from longitudinal drill drives will break ore to a draw point system below. Development is carried out with three boom rubber tyred jumbos. All haulage from the mine is in 20 and 35 tonne rear dump trucks. All aspects of the mining operation are discussed including ventilation, pumping and drainage, services and future planning.

Jan 1, 1974

On the face of it this is an easily answered question. Modern technology and life as we know it today would be impossible without industrial minerals and the responsible utilisation of mineral resources is essential for the economic wellbeing of the nation. The quarrying industry supplies a high percentage of the industrial minerals used in New Zealand and our role therefore, is to ensure a constant supply of high quality roading and concrete aggregates so that society and the community as a whole can develop. We must do this in a manner which causes the least possible disruption to members of the community, which efficiently utilises all the valuable resources, which causes as little pollution as possible and last but by no means least, creates realistic profit for the operator. It is only by achieving a reasonable profit that we are able to continue in business and therefore play our part in the development of the country. Unfortunately, quarries have a poor image and are not generally popular, as on the whole, they are noisy, dirty and dusty and attract large trucks which create traffic problems. Judging by the amount of restrictive legislation with which we have to comply today, not even government or the local authorities want quarries which presents the industry with some serious problems, some of which will be outlined in this paper.

Jan 1, 1978

By A Singleton, J Busfield

World coal producers have been under constant pressure in recent years because of falling export prices arising from oversupply and the Asian slowdown. This has resulted in a dynamic market place, a sharpening of focus on bottom line costs and some rationalisation of participants. Productivity has increased dramatically as many inefficiencies, typical of the coal industry, have been eroded through workplace reform. This is true for the both open cut and underground sectors of the industry. At the same time, the technology of underground mining is undergoing dynamic change. Mine operators are implementing better exploration and planning tools and are also starting to make gains against chronically low equipment availability and utilisation. æStep-changeÆ improvements in output are imminent. As the statutory environment shifts to a æduty of careÆ regime, it is hoped that mine safety performance will improve, particularly with regard to fatalities. The focus of the paper is on the Australian coal sector, although references to international benchmarks are made. Despite environmental threats to the future of coal, it is concluded that the next ten years will see impressive performance results from underground coal mines which will assist coal to maintain its position as the preferred fuel of lowest cost.

Jan 1, 2000

By Mogi G, Akaike A, Yamaguchi U

A new algorithm has been investigated for three-dimensional open pit designs to improve the dynamic cone approach which utilises the dynamic programming technique. The conventional dynamic cone method was improved by introducing examination processes: 1. whether any negative blocks are included in a unit cone or not; and 2. whether it is possible or not to leave the negative blocks unmined in the unit cone without disturbing the geometric condition imposed on the slope angle of the cone. The newly developed algorithm was applied to a large-scale open pit copper mine in a planning stage and the results have been compared with those obtained by the conventional methods.

Jan 1, 1995

By Walker V

The 'MAGNADET' to provide a safe enhanced protection extraneous currents, electricity and radiodetonator was designed electric detonator with against the effects of current leakage, static frequency energy.It has found a particular niche in shaft sinking operations and Mount Isa Mines initiated trials of the system in 1983 as part of the design work for the 3000/3500 orebody access shaft.Initial surface blasts indicated a number of significant advantages which were confirmed during the bench and concrete phase of the M37 shaft sink. The application of 'MAGNADETS' was later extended to the horadiam phase of the project.Details of the exploder capacity calculations for the various M37 round designs are included with the paper.

Jan 1, 1985

Throughout the Kalgoorlie Field the dominant factors influencing all planned exploratory work are: firstly, the general geology of the district, and, secondly, the lode fracture pattern. Superimposed on these, there are innumerable faulting problems which tend to complicate the search for ore.In this paper it is proposed to deal primarily with the lode fracture pattern and to touch on the general geology only insofar as it affects ore distribution. So much has been written on Kalgoorlie geology that it would be impossible to review the literature adequately in a brief paper such as this. The basic facts of rock types and rock distribution are well established and the broad structure of the field is known in the central portion, though it is less well established towards the northern and southern ends.The latest descriptions of the general geology are those of Stillwell (1), and Gustafson (2), -and these represent the basis of current knowledge.GENERAL GEOLOGY.The field is six miles long and about one mile wide, the long axis trending north-west. The "Golden Mile," or heart of the mining 'area, covers a length of three miles in the southern section, and consists of a central core of quartz dolerite greenstone which merges into uralitic quartz 'dolerite on its western margin. The uralitic quartz dolerite is derived from an original quartz dolerite by a low grade...

Jan 1, 1948

By A B. Christie

In Northland, Coromandel, Taupo and Canterbury, weathering and hydrothermal alteration of Cenozoic volcanic rocks has resulted in the formation of various types of clay deposits. Subtropical weathering of rhyolite in the Matauri Bay area (Matauri and Mahimahi deposits) in Northland has formed high quality halloysite deposits. The Matauri Bay halloysite is mined and processed to produce reputedly æthe world's whitest clayÆ that commands a high price in niche ceramic markets. In the Coromandel, some argillic alteration zones contain kaolinite clays (at Hahei) and advanced argillic alteration zones contain kaolinite-gibbsite-pyrophyllite assemblages (at Pumpkin Hill and Lookout Rocks). In addition to known halloysite and kaolinite clay deposits, there is also economic potential for smectite clays produced by hydrothermal alteration of volcanic rocks. Bentonite (mainly ferriferous-beidellite) is mined from weathered basaltic ash in Miocene lake beds at Coalgate in Canterbury.   We have compiled interim mineral deposit profiles for bentonite in basaltic ash, halloysite in rhyolite, kaolinite in altered rhyolitic rocks, kaolinite-gibbsite-pyrophyllite clays in advanced argillic alteration zones and for smectite clays in argillic alteration zones. These deposit profiles include geological and mineralogical attributes, which are linked to the underlying volcanic, hydrothermal and weathering processes that have produced the clay minerals from their source volcanic rocks. Further work on refining the deposit profiles includes characterising the composition of selected deposits to determine spatial trends in mineralogy and geochemistry.

Jan 1, 2007

By C Mpodozis

Central Andean (22¦S to 34¦S latitude) Miocene giant ore deposits share common features that reveal their origin. Tectonic and magmatic features include a relation to a shallow subduction zone, an association with the waning or initiation of a magmatic episode, emplacement at the time of uplift associated with crustal thickening and formation at times of major magmatic changes along the Andean margin. Rare Earth Element (REE) signatures in magmas erupted near the time of mineralisation indicate a progressive change from equilibration at depth with a hydrous, intermediate-pressure amphibole-bearing mineral residue to equilibration with an anhydrous high-pressure garnet-bearing assemblage. These features point to a common history. First, a relatively shallow subduction zone leads to hydration of a cool mantle wedge providing a source of fluids which builds up over at least several million years. Arc magmas formed at this time equilibrate with a hornblende-bearing residual mineralogy. Second, a compressive tectonic regime leads to crustal shortening and thickening that facilitates entrapment of arc magmas in the crust. Eventually, the magma-weakened crust yields to horizontal compression causing rapid crustal thickening. Fluids required for mineralisation are liberated as amphibole-bearing assemblages break down to garnet-bearing ones and over pressured fluids are released from plutons. Mineralisation subsequently ceases in the region unless continued dehydration of the slab and mechanical thinning of the continental lithosphere causes the previous conditions to repeat. The type of mineral deposit generated depends on the pre-existing continental lithosphere and the distance from the trench.

Jan 1, 1999